Generac CX5500 PMC145500.01 Manuel utilisateur

Marque: Generac

Modèle: CX5500 PMC145500.01

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

CX1400/3500/5500 Portable

Generator

Owner’s Manual

SAVE THIS MANUAL FOR FUTURE REFERENCE

001593

(000209a)

WARNING

This product is not intended to be used in

a critical life support application. Failure to

adhere to this warning could result in

death or serious injury.

MODEL:________________________

SERIAL:________________________

DATE PURCHASED:______________

SAVE THIS MANUAL FOR FUTURE REFERENCE

www.powermate.com

1-800-445-1805

Table of Contents

Section 1 Introduction and Safety 1

Introduction ..................................... 1

Safety Rules .................................... 1

Safety Symbols and Meanings ........ 1

Exhaust and Location Hazards ....... 2

Electrical Hazards ........................... 3

Fire Hazards .................................... 3

Standards Index .............................. 3

Section 2 General Information and

Setup .............................................. 4

Know Your Generator ..................... 5

Emissions ........................................ 5

Connection Plugs ............................ 6

Remove Contents from Carton ....... 7

Assembly ......................................... 7

Add Engine Oil ................................ 9

Fuel ............................................... 10

Section 3 Operation .................... 11

Operation and Use Questions ....... 11

Before Starting Engine .................. 11

Prepare Generator for Use ............ 11

Grounding the Generator When In Use

Know Generator Limits .................. 12

Transporting/Tipping of the Unit .... 12

Starting Pull Start Engines ............ 13

Generator Shut Down ................... 13

Low Oil Level Shutdown System ... 13

Section 4 Maintenance and

Troubleshooting ..........................14

Maintenance ..................................14

Maintenance Schedule ..................14

Preventive Maintenance ................14

Engine Maintenance ......................14

Inspect Muffler and Spark Arrestor 16

Valve Clearance ............................16

Storage ..........................................16

Troubleshooting .............................18

Notes .............................................19

(000004)

WARNING

California Proposition 65. Engine exhaust and some

of its constituents are known to the state of California

to cause cancer, birth defects, and other reproductive

harm.

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

Owner’s Manual for Portable Generator 1

Section 1 Introduction and Safety

Introduction

Thank you for purchasing a Powermate prod-

uct. This unit has been designed to provide

high-performance, efficient operation, and

years of use when maintained properly.

If any section of the manual is not understood,

contact your nearest Independent Authorized

Service Dealer (IASD), or contact Powermate

Customer Service at 1-800-445-1805, or

www.powermate.com with any questions or

concerns.

The owner is responsible for proper mainte-

nance and safe use of the equipment. Before

operating, servicing or storing this generator:

• Study all warnings in this manual and on

the product carefully.

• Become familiar with this manual and the

unit before use.

• Refer to the Assembly section of the man-

ual for instructions on final assembly proce-

dures. Follow the instructions completely.

Save these instructions for future reference.

ALWAYS supply this manual to any individual

that will use this machine.

THE INFORMATION CONTAINED HEREIN

WAS BASED ON MACHINES IN PRODUC-

TION AT THE TIME OF PUBLICATION.

POWERMATE RESERVES THE RIGHT TO

MODIFY THIS MANUAL AT ANY TIME.

Safety Rules

The manufacturer cannot anticipate every

possible circumstance that might involve a

hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, there-

fore, not all inclusive. If using a procedure,

work method or operating technique that the

manufacturer does not specifically recom-

mend, verify that it is safe for others. Also

make sure the procedure, work method or

operating technique utilized does not render

the equipment unsafe.

Throughout this publication, and on tags and

decals affixed to the generator, DANGER,

WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions

about a particular operation that may be haz-

ardous if performed incorrectly or carelessly.

Observe them carefully. Their definitions are

as follows:

NOTE: Notes contain additional information

important to a procedure and will be found

within the regular text of this manual.

These safety warnings cannot eliminate the

hazards that they indicate. Common sense

and strict compliance with the special instruc-

tions while performing the action or service

are essential to preventing accidents.

Safety Symbols and Meanings

• If you start to feel sick, dizzy, or weak after

the generator has been running, move to

fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poison-

ing.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

000657

DANGER

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is

a poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

2 Owner’s Manual for Portable Generator

• For safety reasons, it is recommended that

the maintenance of this equipment be per-

formed by an IASD. Inspect the generator

regularly, and contact the nearest IASD for

parts needing repair or replacement.

Exhaust and Location Hazards

• If you start to feel sick, dizzy, or weak after

the generator has been running, move to

fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poison-

ing.

(000179a)

DANGER

The exhaust system must be properly maintained. Do

not alter or modify the exhaust system as to render it

unsafe or make it noncompliant with local codes and/or

standards. Failure to do so will result in death

or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000116)

DANGER

Electrocution. Turn utility and emergency

power supplies to OFF before connecting power

source and load lines. Failure to do so will result

in death or serious injury.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000250)

WARNING

Equipment and property damage. Do not operate unit on

uneven surfaces, or areas of excessive moisture, dirt, dust

or corrosive vapors. Doing so could result in death, serious

injury, property and equipment damage.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and appendages

away from moving parts. Failure to do so could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operting machine, do not

touch hot surfaces. Keep machine away from

combustables during use. Hot surfaces

could result in severe burns or fire.

(000142)

Do not insert any object through the air cooling slots.

Generator can start at any time and could result in

death, serious injury, and unit damage.

WARNING

Risk of injury. Do not operate or service this

machine if not fully alert. Fatigue can impair the

ability to service this equipment and could result

in death or serious injury.

(000215)

WARNING

Injury and equipment damage. Do not use

generator as a step. Doing so could result in falling,

damaged parts, unsafe equipment operation,

and could result in death or serious injury.

(000216)

CAUTION

(000291)

Equipment damage. Do not attempt to start or operate

a unit in need of repair or scheduled maintenance.

Doing so could result in serious injury, death, or

equipment failure or damage.

WARNING

000406

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

(000179a)

DANGER

The exhaust system must be properly maintained. Do

not alter or modify the exhaust system as to render it

unsafe or make it noncompliant with local codes and/or

standards. Failure to do so will result in death

or serious injury.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

Owner’s Manual for Portable Generator 3

Electrical Hazards

• The National Electric Code (NEC) requires

the frame and external electrically conduc-

tive parts of the generator be properly con-

nected to an approved earth ground. Local

electrical codes may also require proper

grounding of the generator. Consult with a

local electrician for grounding requirements

in the area.

• Use a ground fault circuit interrupter in any

damp or highly conductive area (such as

metal decking or steel work).

Fire Hazards

• Wipe up any fuel or oil spills immediately.

Verify that no combustible materials are left

on or near the generator. Keep the area

surrounding the generator clean and free

from debris and keep a clearance of five (5)

feet on all sides to allow for proper ventila-

tion of the generator.

• Do not operate the generator if connected

electrical devices overheat, if electrical out-

put is lost, if engine or generator sparks or if

flames or smoke are observed while unit is

running.

• Keep a fire extinguisher near the generator

at all times.

Standards Index

1. National Fire Protection Association

(NFPA) 70: The NATIONAL ELECTRIC

CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association

(NFPA) 5000: BUILDING CONSTRUC-

TION AND SAFETY CODE available from

www.nfpa.org

3. International Building Code available from

www.iccsafe.org

4. Agricultural Wiring Handbook available

from www.rerc.org, Rural Electricity

Resource Council P.O. Box 309 Wilming-

ton, OH 45177-0309

5. ASAE EP-364.2 Installation and Mainte-

nance of Farm Standby Electric Power

available from www.asabe.org, American

Society of Agricultural & Biological Engi-

neers 2950 Niles Road, St. Joseph, MI

49085

This list is not all inclusive. Check with the

Authority Having Jurisdiction (AHJ) for any

local codes or standards which may be appli-

cable to your jurisdiction.

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident,

immediately shut power OFF. Use non-conductive

implements to free victim from live conductor. Apply

first aid and get medical help. Failure to do so will

result in death or serious injury.

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death

or serious injury.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Add fuel in a well

ventilated area. Keep fire and spark away. Failure to

do so will result in death or serious injury.

(000166)

DANGER

Do not overfill fuel tank. Fill to 1/2 in. of top of tank to

allow for fuel expansion. Overfilling may cause fuel to

spill onto engine causing fire or explosion, which will

result in death or serious injury.

(000142)

Do not insert any object through the air cooling slots.

Generator can start at any time and could result in

death, serious injury, and unit damage.

WARNING

Fire risk. Fuel and vapors are extremely

flammable. Do not operate indoors. Doing so

could result in death, serious injury, or

property or equipment damage.

(000281)

WARNING

Explosion and fire risk. Do not smoke near unit.

Keep fire and spark away. Failure to do so could

result in death, serious injury, or property or

equipment damage.

(000282)

WARNING

Explosion and fire risk. Do not smoke while

refueling unit. Failure to do so could result in

death, serious injury, or property or equipment

damage.

(000284)

4 Owner’s Manual for Portable Generator

Section 2 General Information and Setup

Figure 2-1. Features and Controls

TABLE 1. Generator Components

Figure 2-2. CX1400 Control Panel

Figure 2-3. CX3500 Control Panel (CSA/CARB)

001593

1 120 Volt AC, 20 Amp Duplex Receptacle

2 120/240 Volt AC, 30 Amp Locking

Receptacle (NEMA L14-30R)

3 Circuit Breakers (AC)

4 On/Off Switch

5 Hour Meter

6 Ground Terminal

7 Choke Lever

8 Fuel Tank

9Oil Drain

10 Oil Fill

11 Air Cleaner

12 Recoil Handle

13 Fuel Shutoff Valve

14 Battery Charger

15 Circuit Breaker (DC)

16 120 Volt AC, 30 Amp Locking Receptacle

(NEMA L5-30R)

17 120 Volt AC, 30 Amp Receptacle (NEMA

TT-30R)

18 2-pole Circuit Breaker (AC)

19 120 Volt AC, 20A GFCI Duplex

Receptacle (CX5500 CARB only)

002339

5 1

15 6

002340

3 1

6 16

Owner’s Manual for Portable Generator 5

Figure 2-4. CX5500 Control Panel (CSA/CARB)

Know Your Generator

Replacement owner’s manuals are available

at www.powermate.com.

Emissions

The United States Environmental Protection

Agency (US EPA) (and California Air

Resources Board (CARB), for engines/equip-

ment certified to California standards) requires

that this engine/equipment complies with

exhaust and evaporative emissions stan-

dards. Locate the emissions compliance decal

on the engine to determine applicable stan-

dards. For emissions warranty information,

please reference the included emissions war-

ranty. It is important to follow the maintenance

specifications in the manual to ensure that the

engine complies with the applicable emissions

standards for the duration of the product’s life.

002341

18 5

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

Product Specifications

Generator Specifications 1400 3500 5500

Rated Power 1400W 3500W 5500W

Surge Power 1700W 4375W 6875W

Rated AC Voltage 120 120 120/240

Rated AC Load (Amps) 11.7** 29.2** 45.8 / 22.9**

Rated Frequency

60 Hz @ 3600

RPM

60 Hz @ 3600

RPM

60 Hz @ 3600

RPM

Phase Single Phase Single Phase Single Phase

Unit Weight 60 lbs. (27.2 kg) 107 lbs. (48.5 kg) 173 lbs. (78.5 kg)

** Operating Temperature Range: -18 deg. C (0 deg. F) to 40 Deg. C (104 Deg. F). When operated

above 25 deg. C (77 deg. F) there may be a decrease in power.

** Maximum wattage and current are subject to, and limited by, such factors as fuel Btu content, ambi-

ent temperature, altitude, engine condition, etc. Maximum power decreases about 3.5% for each

1,000 feet above sea level; and will also decrease about 1% for each 6° C (10° F) above 16° C (60°

F) ambient temperature.

Engine Specifications 1400 3500 5500

Displacement 98 cc 208 cc 420 cc

Spark Plug Part No.

NGK BPR6HS or

equivalent

NGK BPR7ES or

equivalent

NGK BPR7ES or

equivalent

Spark Plug Gap

0.028-0.031 inch

(0.70-0.80 mm)

0.028-0.031 inch

(0.70-0.80 mm)

0.028-0.031 inch

(0.70-0.80 mm)

Gasoline Capacity

5.7 L (1.5 U.S.

gallons)

17 L (4.5 U.S.

gallons)

26.5 L (7 U.S.

gallons)

Oil Type

See Chart in

Add

Engine Oil

See Chart in Add

Engine Oil

See Chart in Add

Engine Oil

Oil Capacity 0.4 L (0.4 qt.) 0.6 L (0.6 qt.) 1.0 L (1.0 qt.)

Run Time at 50% Load 9.5 Hours 12 Hours 12.5 Hours

* Go to www.powermate.com or contact an IASD for replacement parts.

6 Owner’s Manual for Portable Generator

Connection Plugs

120 VAC, 20 Amp, Duplex

Receptacle

The 120 Volt outlet is overload protected by a

20 Amp push-to-reset circuit breaker. See Fig-

ure 2-5. Each receptacle will power 120 Volt

AC, single phase, 60 Hz electrical loads

requiring up to 2400 watts (2.4 kW) or 20

Amps of current. Use only high quality, well-

insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater).

NOTE: Limit length of extension cords to fif-

teen feet, or less, to prevent voltage drop and

overheating of wires.

Figure 2-5. 120 VAC, 20 Amp, Duplex

Receptacle NEMA 5-20R

120 VAC, 20 Amp, GFCI Duplex

Receptacle (if equipped)

The 120 Volt outlet is overload protected by a

20 Amp push-to-reset circuit breaker. See Fig-

ure 2-6. Each receptacle will power 120 Volt

AC, single phase, 60 Hz electrical loads

requiring up to 2400 watts (2.4 kW) or 20

Amps of current. Use only high quality, well-

insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater). It also pro-

vides protection with a Ground Fault Circuit

Interrupter with a press to TEST and RESET

button.

NOTE: Limit length of extension cords to fif-

teen feet, or less, to prevent voltage drop and

overheating of wires.

Figure 2-6. 120 VAC, 20 Amp, GFCI Duplex

Receptacle NEMA 5-20R

120 VAC, 30 Amp Receptacle

Use a NEMA TT-30R plug with this receptacle.

Connect a suitable 3-wire cord set to the plug

and to desired load. The cord set should be

rated for 125 Volts AC at 30 Amps (or greater).

See Figure 2-7.

Use this receptacle to operate 120 Volt AC,

60Hz, single phase loads requiring up to 3600

watts (3.6kW) of power at 30 Amps. The outlet

is protected by a 30 Amp push-to-reset circuit

breaker.

Figure 2-7. 120 VAC, 30 Amp Receptacle

NEMA TT-30R

120/240 VAC, 30 Amp Receptacle

Use a NEMA L14-30 plug with this receptacle

(rotate to lock/unlock). Connect a suitable 4-

wire grounded cord set to plug and desired

load. The cord set should be rated 250 Volts

AC at 30 Amps (or greater). See Figure 2-8.

Use this receptacle to operate 120 Volt AC, 60

Hz, single phase loads requiring up to 2760

Watts (2.7 kW) of power at 23 Amps or 240

Volt AC, 60 Hz, single phase loads requiring

up to 5520 watts (5.5 kW) of power at 23

Amps. The outlet is protected by a 2-pole 23

Amp toggle switch circuit breaker.

Figure 2-8. 120/240 VAC, 30 Amp Receptacle

NEMA L14-30R

000424

000203

002226

000204

Owner’s Manual for Portable Generator 7

110/120 VAC, 30 Amp Receptacle

Use a NEMA L5-30 plug with this receptacle

(rotate to lock/unlock). Connect a suitable 3-

wire cord set to the plug and to desired load.

The cord set should be rated for 125 Volts AC

at 30 Amps (or greater). See Figure 2-9.

Use this receptacle to operate 120 Volt AC,

60Hz, single phase loads requiring up to 3600

watts (3.6kW) of power at 30 Amps. The outlet

is protected by a 30 Amp push-to-reset circuit

breaker.

Figure 2-9. 120 VAC, 30 Amp Receptacle

NEMA L5-30

Remove Contents from Carton

1. Open carton completely by cutting each

corner from top to bottom.

2. Remove and verify carton contents prior to

assembly. Carton contents should contain

the following:

TABLE 2. Accessories

3. Call Powermate Customer Service 1-800-

445-1805 with the unit model and serial

number for any missing carton contents.

4. Record model, serial number, and date of

purchase on front cover of this manual.

Assembly

Call Powermate Customer Service at 1-800-

445-1805 for any assembly issues or con-

cerns. Please have model and serial number

available.

The following tools are required to install the

accessory kit.

•See Table 2: Accessories (Tool Kit)

NOTE: The wheels are not intended for over-

the-road use.

Item - All Models Qty.

Main Unit 1

Owner’s Manual 1

Liter SAE Oil 1

Oil Funnel 1

Hardware Bag - CX1400 Qty.

Spark Plug Wrench with Rod 1

Battery Cable Set 1

Hardware Bag - CX3500 Qty.

Wheel (1) 2

Axle Pin (2) 2

Cotter Pin (3) 2

Foot Spacer (4) 2

Rubber Feet (5) 2

M10 x 4mm Flat Washer (6) 2

000844

M6 x 25 Bolt (7) 2

M8 x 65 Bolt (8) 2

M6 Nyloc Nut (9) 2

Hardware Bag - CX5500 Qty.

Wheel (1) 2

Handle and Handle Bracket (2) 2

Axle Pin (3) 2

Cotter Pin (4) 2

Foot Spacer (5) 2

Rubber Feet (6) 2

M12 x 4mm Flat Washer (7) 2

M12 x 1.5mm Flat Washer (8) 2

M8 Flat Washer (9) 2

M8 x 50 Bolt (10) 2

M8 x 80 Bolt (11) 2

M8 Nyloc Nut (12) 4

Handle Grip (13) 2

Tool Kit Qty.

5mm Hex Key 1

10 x 13mm Wrench 1

Spark Plug Wrench with Rod 1

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

8 Owner’s Manual for Portable Generator

CX3500

See Figure 2-11.

Install wheels as follows:

1. Slide axle pin (2) through wheel (1), M10 x

4mm flat washer (6), and frame.

2. Insert cotter pin (3) through axle (2). Bend

tabs (of cotter pins) outward to lock into

place.

Install frame foot assembly as follows:

1. Slide rubber foot (5), M6 nyloc nut (9), and

foot spacer (4) onto M6 x 25 bolt (7).

2. Align through holes in frame rail and

secure with M8 x 65 bolt (8).

Figure 2-10. Wheel and Foot Assembly (CX3500)

CX5500

See Figure 2-11.

Install wheels as follows:

1. Slide axle pin (3) through wheel (1), M12 x

4mm flat washer (7), and frame.

2. Install M12 x 4mm flat washer (7) and

insert cotter pin (4) through axle (3). Bend

tabs (of cotter pins) outward to lock into

place.

Install frame foot assembly as follows:

1. Slide M8 flat washer (9), rubber foot (6),

foot spacer (5) onto M8 x 80 bolt (10).

2. Align through holes in frame rail and

secure with M8 nyloc nut (12).

Install handle as follows:

1. Slide M8 x 50 bolt (10) through handle

bracket and handle (2). Secure with M8

nyloc nut (12).

002346

Owner’s Manual for Portable Generator 9

Figure 2-11. Wheel, Handle and Foot Assembly (CX5500)

Add Engine Oil

1. Place generator on a level surface.

2. Verify oil fill area is clean.

3. Remove oil fill cap and wipe dipstick clean.

See Figure 2-12.

Figure 2-12. Remove Dipstick

4. Add recommended engine oil. Climate

determines proper engine oil viscosity.

See chart to select correct viscosity.

NOTE: Use petroleum based oil (supplied) for

engine break-in before using synthetic oil.

NOTE: Some units have more than one oil fill

location. It is only necessary to use one oil fill

point.

5. Thread dipstick into oil filler neck. Oil level

is checked with dipstick fully installed.

6. See Figure 2-13. Remove dipstick and ver-

ify oil level is within safe operating range.

Figure 2-13. Safe Operating Range

7. Install oil fill cap/dipstick and hand-tighten.

001592

(000135)

CAUTION

Engine damage. Verify proper type and quantity of

engine oil prior to starting engine. Failure to do so

could result in engine damage.

000115

SAE 30

10W-30

Synthetic 5W-30

000399

000116

Owner’s Manual for Portable Generator 10

Fuel

Fuel requirements are as follows:

• Clean, fresh, unleaded gasoline.

• Minimum rating of 87 octane/87 AKI (91

RON).

• Up to 10% ethanol (gasohol) is acceptable

(where available; non-ethanol-premium fuel

is recommended).

• DO NOT use E85.

• DO NOT use a gas oil mix.

• DO NOT modify engine to run on alternate

fuels. Stabilize fuel prior to storage.

1. Verify unit is OFF and cooled for a mini-

mum of two minutes prior to fueling.

2. Place unit on level ground in a well venti-

lated area.

3. Clean area around fuel cap and remove

cap slowly.

4. Slowly add recommended fuel. Do not fill

above red fuel indicator (A). See Figure 2-

14.

5. Install fuel cap.

Figure 2-14. Add Recommended Fuel

NOTE: Allow spilled fuel to evaporate before

starting unit.

IMPORTANT NOTE: It is important to pre-

vent gum deposits from forming in fuel

system parts such as the carburetor, fuel

hose or tank during storage. Alcohol-

blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which

leads to separation and formation of acids

during storage. Acidic gas can damage the

fuel system of an engine while in storage.

To avoid engine problems, the fuel system

should be emptied before storage of 30

days or longer. See the Storage section.

Never use engine or carburetor cleaner

products in the fuel tank as permanent

damage may occur.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

(000166)

DANGER

Do not overfill fuel tank. Fill to 1/2 in. of top of tank to

allow for fuel expansion. Overfilling may cause fuel to

spill onto engine causing fire or explosion, which will

result in death or serious injury.

000206

Owner’s Manual for Portable Generator 11

Section 3 Operation

Operation and Use Questions

Call Powermate customer service at 1-800-

445-1805 with questions or concerns about

equipment operation and maintenance.

Before Starting Engine

1. Verify engine oil level is correct.

2. Verify fuel level is correct.

3. Verify unit is secure on level ground, with

proper clearance and is in a well ventilated

area.

Prepare Generator for Use

Grounding the Generator When

In Use

The generator is equipped with a terminal for

the connection of a grounding electrode sys-

tem. Article 250.34 (A) does not require the

frame of the generator to be connected to a

grounding electrode system when the genera-

tor only supplies power to cord and plug con-

nected equipment through the receptacles on

the generator.

When the generator supplies power to a 3

pole manual transfer switch or distribution

panel boards for temporary power, a ground-

ing electrode system shall be installed and

connected to the grounding electrode terminal

on the generator. See NEC 250.30, 250.34

and 250.52 for clarification. See Figure 3-1.

• Neutral Bonded to Frame

Figure 3-1.Grounding the Generator

Special Requirements

Review all Federal or State Occupational

Safety and Health Administration (OSHA) reg-

ulations, local codes, or ordinances that apply

to the intended use of the generator.

Consult a qualified electrician, electrical

inspector, or the local agency having jurisdic-

tion:

• In some areas, generators are required to

be registered with local utility companies.

• If the generator is used at a construction

site, there may be additional regulations

which must be observed.

Connecting the Generator to a

Building Electrical System

When connecting directly to a building electri-

cal system, it is recommended that a manual

transfer switch be used. Connections for a

portable generator to a building electrical sys-

tem must be made by a qualified electrician

and in strict compliance with all national and

local electrical codes and laws.

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000179a)

DANGER

The exhaust system must be properly maintained. Do

not alter or modify the exhaust system as to render it

unsafe or make it noncompliant with local codes and/or

standards. Failure to do so will result in death

or serious injury.

WARNING

(000118a)

Risk of fire. Do not use generator without

spark arrestor installed. Failure to do so

could result in death or serious injury.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

002341

12 Owner’s Manual for Portable Generator

Know Generator Limits

Overloading a generator can result in damage

to the generator and connected electrical

devices. Observe the following to prevent

overload:

• Add up the total wattage of all electrical

devices to be connected at one time. This

total should NOT be greater than the gener-

ator's wattage capacity.

• The rated wattage of lights can be taken

from light bulbs. The rated wattage of tools,

appliances, and motors can be found on a

data label or decal affixed to the device.

• If the appliance, tool, or motor does not

give wattage, multiply volts times ampere

rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction

types, require about three times more watts

of power for starting than for running. This

surge of power lasts only a few seconds

when starting such motors. Make sure to

allow for high starting wattage when select-

ing electrical devices to connect to the gen-

erator:

1. Figure the watts needed to start the largest

motor.

2. Add to that figure the running watts of all

other connected loads.

The Wattage Reference Guide is provided to

assist in determining how many items the gen-

erator can operate at one time.

NOTE: All figures are approximate. See data

label on appliance for wattage requirements.

Table 3. Wattage Reference Guide

Transporting/Tipping of the Unit

Do not operate, store or transport the unit at

an angle greater than 15 degrees.

Device Running

Watts

*Air Conditioner (12,000 Btu) 1700

*Air Conditioner (24,000 Btu) 3800

*Air Conditioner (40,000 Btu) 6000

Battery Charger (20 Amp) 500

Belt Sander (3") 1000

Chain Saw 1200

Circular Saw (6-1/2") 800 to 1000

*Clothes Dryer (Electric) 5750

*Clothes Dryer (Gas) 700

*Clothes Washer 1150

Coffee Maker 1750

*Compressor (1 HP) 2000

*Compressor (3/4 HP) 1800

*Compressor (1/2 HP) 1400

Curling Iron 700

*Dehumidifier 650

Disc Sander (9") 1200

Edge Trimmer 500

Electric Blanket 400

Electric Nail Gun 1200

Electric Range (per element) 1500

Electric Skillet 1250

*Freezer 700

*Furnace Fan (3/5 HP) 875

*Garage Door Opener 500 to 750

Hair Dryer 1200

Hand Drill 250 to 1100

Hedge Trimmer 450

Impact Wrench 500

Iron 1200

*Jet Pump 800

Lawn Mower 1200

Light Bulb 100

Microwave Oven 700 to 1000

*Milk Cooler 1100

Oil Burner on Furnace 300

Oil Fired Space Heater (140,000

Btu)

400

Oil Fired Space Heater (85,000 Btu) 225

Oil Fired Space Heater (30,000 Btu) 150

*Paint Sprayer, Airless (1/3 HP) 600

Paint Sprayer, Airless (hand-held) 150

Radio 50 to 200

*Refrigerator 700

Slow Cooker 200

*Submersible Pump (1-1/2 HP) 2800

*Submersible Pump (1 HP) 2000

*Submersible Pump (1/2 HP) 1500

*Sump Pump 800 to 1050

*Table Saw (10") 1750 to 2000

Television 200 to 500

Toaster 1000 to 1650

Weed Trimmer 500

* Allow 3 times the listed watts for starting these

devices.

Owner’s Manual for Portable Generator 13

Starting Pull Start Engines

1. Unplug all electrical loads from the unit's

receptacles before starting engine.

2. Place generator on a level surface.

3. See Figure 3-2. Open the fuel shut-off

valve (A).

4. Turn engine ON/OFF switch (B) to ON.

See Figure 3-2.

Figure 3-2.Engine Controls

5. Slide engine choke (C) to Full CHOKE

position (left). See Figure 3-3.

Figure 3-3.Choke Position

6. See Figure 3-2. Firmly grasp recoil handle

(D) and pull slowly until increased resis-

tance is felt. Pull rapidly up and away.

7. When engine starts, move choke lever to

1/2 CHOKE position until engine runs

smoothly, then fully into ON position. If

engine falters, move choke back to 1/2-

CHOKE position until engine runs

smoothly, then to ON position.

NOTE: If engine fires, but does not continue to

run, move choke lever to Full CHOKE and

repeat starting instructions.

IMPORTANT NOTE:Do not overload gener-

ator or individual panel receptacles. These

outlets are overload protected with push-

to-reset circuit breakers. If amperage rat-

ing of any circuit breaker is exceeded, that

breaker opens and electrical output to that

receptacle is lost. Read Know Generator

Limits carefully.

Generator Shut Down

1. Shut off all loads and unplug electrical

loads from generator panel receptacles.

2. Let engine run at no-load for several min-

utes to stabilize internal temperatures of

engine and generator.

3. Move ON/OFF switch to OFF.

4. Close fuel valve.

NOTE: Under normal conditions, close fuel

valve and allow generator to run carburetor

bowl out of fuel. For emergencies, switch to

OFF.

Low Oil Level Shutdown System

The engine is equipped with a low oil level

sensor that shuts down the engine automati-

cally when the oil level drops below a speci-

fied level. The engine will not run until the oil

has been filled to the proper level.

If the engine shuts down and there is sufficient

fuel, check engine oil level.

(000183)

WARNING

Recoil Hazard. Recoil could retract unexpectedly.

Kickback could result in death or serious injury.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

001593

000209

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

14 Owner’s Manual for Portable Generator

Section 4 Maintenance and Troubleshooting

Maintenance

Regular maintenance will improve perfor-

mance and extend engine/equipment life. The

manufacturer recommends that all mainte-

nance work be performed by an Independent

Authorized Service Dealer (IASD). Regular

maintenance, replacement or repair of the

emissions control devices and systems may

be performed by any repair shop or person of

the owner’s choosing. However, to obtain

emissions control warranty service free of

charge, the work must be performed by an

IASD. See the emissions warranty.

NOTE: Call Powermate customer service at 1-

800-445-1805 with questions about compo-

nent replacement.

Maintenance Schedule

Follow maintenance schedule intervals,

whichever occurs first according to use.

NOTE: Adverse conditions will require more

frequent service.

NOTE: All required service and adjustments

should be each season as detailed in the fol-

lowing chart.

Preventive Maintenance

Dirt or debris can cause improper operation

and equipment damage. Clean generator

daily or before each use. Keep area around

and behind muffler free from combustible

debris. Inspect all cooling air openings on

generator.

• Use a damp cloth to wipe exterior surfaces

clean.

• Use a soft bristle brush to loosen caked on

dirt, oil, etc.

• Use a vacuum to pick up loose dirt and

debris.

• Low pressure air (not to exceed 25 psi)

may be used to blow away dirt. Inspect

cooling air slots and openings on generator.

These openings must be kept clean and

unobstructed.

NOTE: DO NOT use a garden hose to clean

generator. Water can enter engine fuel system

and cause problems. If water enters generator

through cooling air slots, some water will be

retained in voids and crevices of rotor and sta-

tor winding insulation. Water and dirt buildup

on generator internal windings will decrease

insulation resistance of windings.

Engine Maintenance

Engine Oil Recommendations

To maintain the product warranty, the engine

oil should be serviced in accordance with the

recommendations of this manual. For your

convenience, maintenance kits designed and

intended for use on this product are available

from the manufacturer that include engine oil,

oil filter, air filter, spark plug(s), a shop towel

and funnel. These kits can be obtained from

an Independent Authorized Service Dealer

(IASD).

At Each Use

Check engine oil level

Every 100 Hours or Every Season*

Change oil ǂ

Change fuel filter

Every Season

Replace spark plug

Check valve clearance***

Every 200 Hours or Every Season

Inspect/clean air filter**

ǂ Change oil after first 30 hours of operation,

then every season.

hange oil and oil filter every month when

operating under heavy load or in high tem-

peratures.

** Clean more often under dirty or dusty oper-

ating conditions. Replace air filter parts if

they cannot be adequately cleaned.

*** Check valve clearance and adjust if neces-

sary after first 50 hours of operation and

every 100 hours thereafter.

(000142)

Do not insert any object through the air cooling slots.

Generator can start at any time and could result in

death, serious injury, and unit damage.

WARNING

(000141)

WARNING

Accidental start-up. Disconnect spark plug wires

when working on unit. Failure to do so could result

in death or serious injury.

Owner’s Manual for Portable Generator 15

Inspect Engine Oil Level

Inspect engine oil level prior to each use, or

every 8 hours of operation.

1. Place generator on a level surface.

2. Clean area around oil fill.

3. See Figure 4-1. Remove oil fill cap and

wipe dipstick clean.

Figure 4-1. Engine Oil Fill

4. Screw dipstick into filler neck. Remove

dipstick and verify oil level is within safe

operating range. See Figure 4-2.

Figure 4-2. Safe Operating Range

5. Add recommended engine oil as neces-

sary.

6. Install oil fill cap and hand-tighten.

NOTE: Some units have more than one oil fill

location. It is only necessary to use one oil fill

point.

Change Engine Oil

When using generator under extreme, dirty,

dusty conditions, or in extremely hot weather,

change oil more frequently.

NOTE: Don’t pollute. Conserve resources.

Return used oil to collection centers.

Change oil while engine is still warm from run-

ning, as follows:

1. Place generator on a level surface.

2. Disconnect the spark plug wire from the

spark plug and place the wire where it

cannot contact spark plug.

3. Clean area around oil fill, and oil drain

plug.

4. Remove oil fill cap.

5. Remove oil drain plug and drain oil com-

pletely into a suitable container.

6. Install oil drain plug and tighten securely.

7. Slowly pour oil into oil fill opening until oil

level is within safe operating range. DO

NOT overfill.

8. Install oil fill cap, and hand-tighten.

9. Wipe up any spilled oil.

10. Properly dispose of oil in accordance with

all applicable regulations.

Air Filter

Engine will not run properly and may be dam-

aged if run with a dirty air filter. Service air fil-

ter more frequently in dirty or dusty conditions.

To service air filter:

1. See Figure 4-3. Turn knob (A) and remove

air filter cover.

2. Wash in soapy water. Squeeze filter dry in

clean cloth (DO NOT TWIST).

3. Clean air filter cover before re-installing it.

NOTE: To order a new air filter, contact the

nearest authorized service center at 1-888-

436-3722.

Figure 4-3. Air Filter Assembly

SAE 30

10W-30

Synthetic 5W-30

000399

(000139)

WARNING

Risk of burns. Allow engine to cool before

draining oil or coolant. Failure to do so

could result in death or serious injury.

000115

000116

(000141)

WARNING

Accidental start-up. Disconnect spark plug wires

when working on unit. Failure to do so could result

in death or serious injury.

000379

16 Owner’s Manual for Portable Generator

Service Spark Plug

To service spark plug:

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Inspect electrode gap with wire feeler

gauge and reset spark plug gap to

0.028-0.031 in (0.7-0.8 mm). See Figure

4-4.

Figure 4-4. Spark Plug

NOTE: Replace spark plug if electrodes are

pitted, burned or porcelain is cracked. Use

ONLY recommended replacement plug. See

Specifications.

4. Install spark plug finger tight, and tighten

an additional 3/8 to 1/2 turn using spark

plug wrench.

Inspect Muffler and Spark

Arrestor

NOTE: It is a violation of California Public

Resource Code, Section 4442, to use or oper-

ate the engine on any forest-covered, brush-

covered, or grass-covered land unless the

exhaust system is equipped with a spark

arrestor, as defined in Section 4442, main-

tained in effective working order. Other states

or federal jurisdictions may have similar laws.

Contact original equipment manufacturer,

retailer, or dealer to obtain a spark arrestor

designed for exhaust system installed on this

engine.

NOTE: Use ONLY original equipment replace-

ment parts.

Inspect muffler for cracks, corrosion, or other

damage. Remove spark arrestor, if equipped,

inspect for damage or carbon blockage.

Replace parts as required.

Inspect Spark Arrestor Screen

(CARB models)

1. See Figure 4-5. Loosen screw and remove

retainer clamp (A) and retainer (B).

2. Remove retainer screw (C) from muffler

outlet tube.

3. Remove screen (D) and replace if torn,

perforated or otherwise damaged. If

screen is not damaged, clean with com-

mercial solvent.

4. Replace screen and retainer, secure with

screw.

5. Install clamp.

Figure 4-5. Spark Arrestor Screen

Valve Clearance

IMPORTANT NOTE: If uncomfortable about

doing this procedure, or the proper tools

are not available, take generator to the

nearest service center to have valve clear-

ance adjusted.

Check valve clearance after the first fifty-hours

of operation. Adjust as necessary.

• Intake – 0.1mm ± 0.02mm (cold), (0.004” ±

0.001” inches)

• Exhaust – 0.15mm ± 0.02mm (cold),

(0.006” ± 0.001” inches)

Storage

General

It is recommended to start and run the genera-

tor for 30 minutes, every 30 days. If this is not

possible, refer to the following list to prepare

unit for storage.

• DO NOT place a storage cover on a hot

generator. Allow unit to cool to room tem-

perature before storage.

• DO NOT store fuel from one season to

another unless properly treated.

• Replace fuel container if rust is present.

Rust in fuel will cause fuel system prob-

lems.

000211

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

001530

(000143)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Store fuel in a well

ventilated area. Keep fire and spark away. Failure

to do so will result in death or serious injury.

(000109)

WARNING

Risk of Fire. Verify machine has properly

cooled before installing cover and storing

machine. Hot surfaces could result in fire.

Owner’s Manual for Portable Generator 17

• Cover unit with a suitable protective, mois-

ture resistant cover.

• Store unit in a clean and dry area.

• Always store generator and fuel away from

heat and ignition sources.

Prepare Fuel System for Storage

Fuel stored over 30 days can go bad and

damage fuel system components. Keep fuel

fresh, use fuel stabilizer.

If fuel stabilizer is added to fuel system, pre-

pare and run engine for long term storage.

Run engine for 10-15 minutes to circulate sta-

bilizer throughout fuel system. Adequately

prepared fuel can be stored up to 24 months.

NOTE: If fuel has not been treated with fuel

stabilizer, it must be drained into an approved

container. Run engine until it stops from lack

of fuel. Use of fuel stabilizer in fuel storage

container is recommended to keep fuel fresh.

1. Change engine oil.

2. Remove spark plug.

3. Pour tablespoon (5-10cc) of clean engine

oil or spray a suitable fogging agent into

cylinder.

4. Pull starter recoil several times to distrib-

ute oil in cylinder.

5. Install spark plug.

6. Pull recoil slowly until resistance is felt.

This will close valves so moisture cannot

enter engine cylinder. Gently release

recoil.

Change Oil

Change engine oil before storage. See

Change Engine Oil.

(000181)

WARNING

Vision Loss. Eye protection is required to avoid

spray from spark plug hole when cranking engine.

Failure to do so could result in vision loss.

18 Owner’s Manual for Portable Generator

Troubleshooting

PROBLEM CAUSE CORRECTION

Engine is running, but

AC output is not

available.

1. Circuit breaker OPEN.

2. Poor connection or defective

cord set.

3. Connected device is bad.

4. Fault in generator.

5. GFCI receptacle is OPEN (if

equipped).

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is

in good condition.

4. Contact IASD.

5. Correct ground fault and press

reset button on GFCI recepta-

cle (if equipped).

Engine runs well at

no-load, but bogs when

load is applied.

1. Short circuit in a connected

load.

2. Generator is overloaded.

3. Engine speed is too slow.

4. Shorted generator circuit.

5. Dirty fuel filter.

1. Disconnect shorted electrical

load.

2. See

Know Generator Limits.

3. Contact IASD.

4. Contact IASD.

5. Replace fuel filter.

Engine will not start; or

starts and runs rough.

1. ON/OFF switch is OFF.

2. Fuel shut-off is OFF.

3. Dirty air filter.

4. Out of fuel.

5. Stale fuel.

6. Spark plug wire not connected

to spark plug.

7. Bad spark plug.

8. Water in fuel.

9. Overchoking.

10. Low oil level.

11. Excessive rich fuel mixture.

12. Intake valve stuck open or

closed.

13. Engine lost compression.

14. Dirty fuel filter.

1. Turn ON/OFF switch ON.

2. Turn fuel shut-off ON.

3. Clean or replace air filter.

4. Fill fuel tank.

5. Drain fuel tank and fill with

fresh fuel.

6. Connect wire to spark plug.

7. Replace spark plug.

8. Drain fuel tank; fill with fresh

fuel.

9. Set choke to no choke posi-

tion.

10. Fill crankcase to correct level.

11. Contact IASD.

12. Contact IASD.

13. Contact IASD.

14. Replace fuel filter.

Engine shuts down

during operation.

1. Out of fuel.

2. Low oil level.

3. Fault in engine.

1. Fill fuel tank.

2. Fill crankcase to correct level.

3. Contact IASD.

Engine lacks power. 1. Load is too high.

2. Dirty air filter.

3. Engine needs to be serviced.

4. Dirty fuel filter.

1. Reduce load (see

Know Gen-

erator Limits).

2. Clean or replace air filter.

3. Contact IASD.

4. Replace fuel filter.

Engine surges or

stumbles.

1. Choke is opened too soon.

2. Carburetor is running too

rich

or t

oo lean.

1. Set choke to halfway position

ntil engine runs smoothly.

2. Contact IASD.

La page charge ...

Generac CX5500 PMC145500.01 Manuel utilisateur

Marque: Generac

Modèle: CX5500 PMC145500.01

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac CX5500 PMC145500.01 User manual
español: Generac CX5500 PMC145500.01 Manual de usuario

Documents connexes

Generac WX5400 PM0145400.01 Manuel utilisateur