Brickcom OB-130N Series Hardware User Manual

Taper
Hardware User Manual

Ce manuel convient également à

Hardware Users Manual
Megapixel Day & Night
Outdoor Bullet Network Camera
Quality Service Group
Outdoor Bullet V2 Series
Review History:
1. Separate User Manual into HW and SW.
2. Merge OB-100A V2 series /OB-130N-series into this User Manual.
3. Add OB-500A Series /OB-300N Series into the User Manual.
4. Clarify the OB series Reset button and WPS button.
5. HW add one function for TV out Connector.
6. Modify I/O Terminal Block definition.
Product name:
Network Camera (Outdoor Bullet V2 series)
Release Date:
2013/01
Manual Revision:
V3.4
Web site:
www.brickcom.com
Email:
© 2011 Brickcom Corporation. All Rights Reserved
Table of Contents
Before You Use This Product ....................................................................................... 1
Regulatory Information ................................................................................................. 2
Plaque signalétique du produit final ..................................................................... 4
Chapter 1 - Package Contents ...................................................................................... 6
Chapter 2 - Outdoor Bullet Network Camera Overview .............................................. 9
Chapter 3 - Device Appearance Description ............................................................. 10
Chapter 4 - Installation ................................................................................................ 16
4.1 Hardware Installation .................................................................................... 16
4.2 Camera Connection ....................................................................................... 22
4.3 System Requirements ................................................................................... 24
4.4 Software Installation ...................................................................................... 25
4.3.1 EasyConfig ........................................................................................... 33
1
Before You Use This Product
In many countries, there are laws prohibiting or restricting the use of surveillance
devices. This Network Camera is a high-performance, web-ready camera which can be
part of a flexible surveillance system. It is the users responsibility to ensure that the
operation of this camera is legal before installing this unit for its intended use.
Upon opening the product’s package, verify that all the accessories listed on the
“Package Contents” are included. Before installing the Network Camera, read the
warnings in the “Quick Installation Guide” to avoid misuse. When installing the Network
Camera, carefully read and follow the instructions in the “Installation” chapters to avoid
damages due to faulty assembly or installation.
2
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are
country dependent and are firmware programmed at the factory to match the
intended destination. The firmware setting is not accessible by the end user.
3
Industry Canada statement:
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout
brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.
Avertissement:
Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux.
Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,
qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars
pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Conformement a la reglementation d'Industrie Canada, le present emetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inferieur) approuve pour
l'emetteur par Industrie Canada. Dans le but de reduire les risques de brouillage
radioelectrique a l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain
de sorte que la puissance isotrope rayonnee equivalente (p.i.r.e.) ne depasse pas l'intensite
necessaire a l'etablissement d'une communication satisfaisante.
Le present emetteur radio (IC: 9219A-WMDR129N)a ete approuve par Industrie Canada pour
fonctionner avec les types d'antenne enumeres ci-dessous et ayant un gain admissible
maximal et l'impedance requise pour chaque type d'antenne. Les types d'antenne non inclus
dans cette liste, ou dont le gain est superieur au gain maximal indique, sont strictement
interdits pour l'exploitation de l'emetteur.
4
Ce dispositif a ete concu pour fonctionner avec une antenne ayant un gain maximal de dB
[2.02]. Une antenne a gain plus eleve est strictement interdite par les reglements d'Industrie
Canada. L'impedance d'antenne requise est de 50 ohms.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:
(Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne,
3) Pour tous les produits vendus au Canada, OEM doit limiter les fréquences de
fonctionnement CH1 à CH11 pour bandes de fréquences 2.4G grâce aux outils de
microprogrammation fournis. OEM ne doit pas fournir d'outil ou d'informations à l'utilisateur
final en ce qui concerne le changement de réglementation de domaine.
Tant que les 3 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable
des essais sur son produit final pour toutes exigences de conformité supplémentaires
requis pour ce module installé.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé
de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation
distincte au Canada.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue
entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible
avec l'inscription suivante: "Contient des IC: 9219A-WMDR129N.
5
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du
produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises
et avertissements comme indiqué dans ce manuel.
6
Chapter 1 - Package Contents
Please check to make sure the product package contains all the accessories listed
below.
A. Camera Package Contents
a. Network Camera
(Outdoor Bullet V2 Series)
b. Shielding Cover
c. Screw bag
d. Product CD
e. Warranty Card / Easy Installation
Guide
f. 2 Water Proof Connectors
g. Dry Bag
h. High Power POE (Optional)
i. Bracket (Optional)
j. Bracket Assembly Plate (Optional)
k. Wi-Fi Dual Band Antenna package
(Optional)
l. 3G Antenna package (Optional)
7
m. Power adapter
B. Wi-Fi Antenna Package contents (Optional)
Refer to the installation guide included in the package when installing the
Wi-Fi antenna
a. Wi-Fi Dual Band Antenna
b. Extension Cable
c. Surge Arrestor Kit
d. Mount Kit
8
C. Wi-Fi Antenna Package contents (Optional)
Refer to the installation guide included in the package when installing the
3G antenna
a. 3G Antenna
b. Extension Cable
c. Surge Arrestor Kit
d. Mount Kit
9
Chapter 2 - Outdoor Bullet Network
Camera Overview
The Brickcom Outdoor Bullet SERIES is an outdoor bullet network camera. It adopts
a megapixel sensor which allows the camera to deliver extremely clear and detailed
images that CCTV cameras cannot offer. To optimize use of the megapixel resolution,
the Outdoor Bullet SERIES uses efficient H.264/ MJPEG/ MPEG-4 codec
compression to deliver dual configurable video streams simultaneously at up to 30 fps.
These features make this series the perfect outdoor camera for neighborhood, school
campus, and parking lot surveillance.
The Outdoor Bullet SERIES has many user friendly features, such as the Smart Focus
capability which allows users to configure settings for excellent image quality without
difficult procedures. Support for Power over Ethernet enables the camera to use the
same cable for power and data transmission, eliminating the need to install an external
power supply.
Installation for the WOB/GOB Series models is not restricted by location or landforms.
The cameras offer various wireless options that make connecting to networks easier
by adopting the technology of IEEE 802.11 a/b/g/n and 3G SIM module. The wireless
Bullet Cameras can be set within any wireless or 3G signal coverage areas. Users
do not have to worry about the data connection failing because each camera is
equipped with a SD/SDHC memory card slot for local storage.
With an IP67 certified outdoor enclosure, the Outdoor Bullet SERIES is not only
weather proof, but also dust and rust resistant. By utilizing a built-in industrial fan and
heater, it can perform well in extreme environments.
10
Chapter 3 - Device Appearance Description
< Front Panel >
< Rear Panel >
< Top >
11
< Bottom >
< Side >
**3G SIM Card Slot only apply for GOB-100Ap/GOB-130Np/GOB-132Np/GOB-500Ap
GOB-502Ap/GOB-302Np/GOB-300Np**
3G SIM Card Slot
12
<Inside> TV out Connector
***This function only apply below models.***
OB-502A Series/OB-500A Series and OB-302N Series/OB-300NSeries
< Extension I/O Terminal Block >
The Network Camera provides an extension I/O terminal block which is used to connect
the camera with external input/output devices. The pin definitions are listed as below.
Pin No.
Pin 1
Power +4.5V
Pin 2
Digital Output
Pin 3
Digital Input
Pin 4
Ground
Pin 5
RS-485-
Pin 6
RS-485+
Pin 7
Audio-in
Pin 8
Audio-out
13
< DI/DO Diagram >
14
OB-100Ap Series and OB-130N Series
Reset button
OB-502A Series and OB-302N Series
Reset Button and WPS button
**WPS Button only applies for WOB-502A Series/WOB-500Ap Series /WOB-302Np
Series/WOB-300Np Series**
<Noted> WPS button for quickly link to WiFi.
15
< Hardware Reset >
The Reset Button can be used to reboot the camera or restore it to factory default
settings. If the camera experiences a problem, rebooting the camera may correct the
problem. If the problem remains, please restore the camera to factory default settings
and reinstall the software.
To Reboot
Press and hold the Reset Button for one second using a paper clip or thin object. Wait
for the camera to reboot.
To Restore
Press and hold the Reset Button for ten seconds until the LED light turns off. When
successful restored, the LED will be blue during normal operation.
NOTE - By restoring the camera, all settings will be restored to the factory
default settings.
Micro-SD/SDHC Card Capacity
The network camera is compatible with Micro-SD/SDHC (Maximum 32GB) cards.
(*) These are optional features. Please refer to the Product List for the full list of
optional features that are available for this product.
16
Chapter 4 - Installation
4.1 Hardware Installation
WARNING - Do not mount the camera on a soft material. The camera
may fall and be damaged.
A. Micro-SD/SDHC Card and 3G SIM Card Installation
a. Remove the Lens cover from the Bullet Camera.
b. Inset the Micro SD/SDHC card and 3G SIM card(*) into their
respective slots.
c. Place a dry bag onto the camera device.
d. Reattach the Lens cover and secure the cover to the top of the
camera device using two screws.
17
B. Wall Installation Using the Optional Bracket
a. Using the Bracket plate as a guide, drill three holes into the wall and
hammer the supplied plastic anchors into the three holes. Use a
screwdriver and the supplied screws to secure the plate to the wall.
b. Attach the Bracket Assembly Plate to the bottom of the camera using
two screws.
c. (1) Use the two supplied screws to secure the bracket to the side of
the camera. (2) Push back the spring on the mortise lock and hook
the camera and attached bracket onto the groove of the wall mount
bracket as shown in the diagram.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43

Brickcom OB-130N Series Hardware User Manual

Taper
Hardware User Manual
Ce manuel convient également à

dans d''autres langues