Kichler 330130 Guide d'installation

Product images may vary slightly from actual product.

56” Almere

INSTRUCTION MANUAL

Model# 330130READ AND SAVE THESE INSTRUCTIONS

2 | KICHLER.COM

TABLE OF CONTENTS

ELECTRICAL CONNECTIONS……………………………………………12

INSTALLING THE WALL CONTROL…………………………………14

COMPLETING THE FAN INSTALLATION………………………15

OPERATING INSTRUCTIONS……………………………………………16

FCC INFORMATION……………………………………………………………17

TROUBLESHOOTING………………………………………………………18

SAFETY RULES……………………………………………………………………3

TOOLS REQUIRED………………………………………………………………5

PACKAGE CONTENTS…………………………………………………………5

MOUNTING OPTIONS…………………………………………………………6

ATTACHING THE FAN BLADES…………………………………………7

HANGING THE FAN……………………………………………………………8

INSTALLATION OF SAFETY SUPPORT……………………………11

fan support and may need to be replaced. Due to the

complexity of the installation of this fan, a qualified

licensed electrician is strongly recommended.

6. The outlet box and support structure must be

securely mounted and capable of reliably supporting

a minimum of 15.9 kg (35 pounds). Use only cULus

Listed outlet boxes marked “Acceptable for Fan

Support of 15.9 kg (35 lbs) or less”.

7. The fan must be mounted with a minimum of 2.1 m (7

feet) clearance from the trailing edge of the blades to

the floor.

8. WARNING: Do not operate reversing switch while

fan blades are in motion. Fan must be turned o and

blades stopped before reversing blade direction.

9. Avoid placing objects in the path of the blades.

10. WARNING: make sure the power is disconnected

before cleaning your fan.

56” Almere | 3

READ AND SAVE THESE INSTRUCTIONS

SAFETY RULES

WARNING: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO THE BUILDING STRUCTURE / CEILING JOIST.

DON’T SECURE THIS FAN TO AN OUTLET BOX.

1. CAUTION – RISK OF SHOCK: Disconnect Power at

the main circuit breaker panel or main fusebox before

starting and during the installation.

2. WARNING: All wiring must be in accordance with the

National Electrical Code “ANSI/NFPA 70” and local

electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

3. WARNING: To reduce the risk of electric shock, this

fan must be installed with a general-use, isolating wall

control/switch.

4. WARNING: Not suitable for use with solid-state speed

controls.

5. WARNING: To reduce the risk of fire, electric shock,

or personal injury, mount to outlet box marked

“acceptable for fan support of 15.9 kg (35 lbs.) or

less” and use mounting screws provided with the

outlet box. Most outlet boxes commonly used for

the support of light fixtures are not acceptable for

4 | KICHLER.COM

16. N.W. 7.82 KGS (17.24 LBS) / G.W. 8.75 KGS (19.29 LBS)11. To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

12. Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

13. After making electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be

spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the

outlet box and the ungrounded conductor on the

other side of the outlet box.

14. Electrical diagrams are reference only. Light kits that

are not packed with the fan must be cULus Listed

and marked suitable for use with the model fan you

are installing. Switches must be cULus General Use

Switches. Refer to the Instructions packaged with the

light kits and switches for proper assembly.

15. All set screws must be checked, and retightened

where necessary, before installation.

SAFETY RULES

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADES DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

• Phillips Screwdriver

• Blade Screwdriver

• 11 mm Wrench

• Step Ladder

• Wire Cutters

Unpack your fan and check the contents . You should have the following items:

A. Ball/Downrod Assembly

B. Mounting Bracket

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Assembly

G. Blade (3)

H. Blade Holder

A

B

G

H

C

D

E

I J

F

56” Almere | 5

I. Wall Control Unit

Face plate (1); Wall control (1); Receiver(1);

Wire Connector (4+5);

Long screw (2);

J. Package hardware

1.) Safety cable hardware: Wood screw (1);

Spring washer (1); Flat washer (1)

2.) Mounting hardware: Wire Connector (3);

3.) Blade attachment hardware: Screw (12);

4.) Motor Assembly attachment hardware: Screw (3) x12

x3

x1

x3

6 | KICHLER.COM

Fig. 1

Outlet box

Fig. 2

Fig. 3

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 22° ANGLE

Fig. 4

Outlet box

MOUNTING OPTIONS

If there is not an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the full weight of the fan (up

to 15.9kg (35 pounds)). Do not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12" is suggested for optimal operation.

NOTE: You must use 12" or longer downrod for 22° slope

(max angle 22°). (Fig. 3)

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist Hanger”

for the support of the outlet box. Make sure the joist hanger you

purchase has been designed for use with ceiling fans. (Fig. 4)

56” Almere | 7

ATTACHING THE FAN BLADES

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The

Electrical Supply Circuit To The Fan Before Installing Fan Blades.

Step 1. Align the four holes in a blade with four matching holes in the

blade holder. Thread blade attachment screws into the aligned holes,

and tighten screws to secure the blade to the blade holder. Repeat for

remaining blades. (Fig. 5)

Step 2. NOTE: Inside of the blade holder there are six tabs. Three of the

tabs have a post on top, and three of the tabs have a hole in the center.

NOTE: In the outer ring of the motor assembly there are six holes. Three

of the holes are smaller in size and three of the holes are larger in size.

Carefully insert the motor assembly into the blade holder, aligning the

smaller holes in the motor assembly with the posts on top of the tabs.

Pass the posts through the smaller holes, and seat the outer ring of the

motor assembly on top of all six tabs.

The larger holes in the motor assembly should align with the holes in

the tabs. Thread the three motor assembly attachment screws into the

larger holes in the motor assembly and into the holes in the tabs, and

tighten to secure the motor assembly to the blade holder. (Fig. 6)” Fig. 6

Fig. 5

Blade Holder

Blade Attachment

Screws

Blade

Tab With Hole

Blade Holder

Motor Assembly

Tab With Post

Motor Assembly

Attachment Screws

8 | KICHLER.COM

Fig. 7

Fig. 8

Fig. 9

Outlet Box

Ceiling Mounting

Bracket

Flat Washer

Screw

Set Screw

Hanger Ball

Cross Pin

Clevis Pin

Downrod

Hairpin

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is necessary for

your safety and also the proper programming of the control system.

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely

fastened to at least two points to a structural ceiling member (a loose box will cause the

fan to wobble). Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. Install mounting bracket to outlet box in ceiling

using the screws and washers included with the outlet box. (Fig. 7)

Step 2. Remove the hairpin and clevis pin from the downrod assembly, retain for later

use. Remove the hanger ball from the downrod assembly by loosening set screw,

removing the cross pin, and sliding ball o of the rod. (Fig. 8)

NOTE: Make sure to keep loosened hardware separate to avoid confusion during

installation.

Step 3. Loosen the two set screws on the motor coupling. (Fig. 9)

Set Screw

Motor Coupling

56” Almere | 9

Step 4. Carefully feed fan wires and safety cable up through the

downrod. Thread the downrod onto the motor coupling until the clevis

pin holes are aligned. Next, replace the clevis pin and hairpin, then tighten

both set screws. (Fig. 10)

Step 5. Slip the coupling cover, canopy hole cover and canopy onto the

downrod. Carefully reinstall the hanger ball onto the downrod. Make sure

the cross pin is in the correct position and the set screw is tight and the

wires are not twisted . ( Fig. 11)

CAUTION: Ensure all screws are tight before moving to the next step.

HANGING THE FAN (continued)

Motor Coupling

Downrod

Cross Pin

Set Screw

Hairpin Clevis Pin

Set Screw

Fig. 10

Fig.11

Canopy

Hanger Ball

Canopy Hole Cover

Coupling Cover

Downrod

10 | KICHLER.COM

Step 6. Now lift the motor assembly into position and place the hanger

ball into the mounting bracket. Rotate until the “Check Tab” has dropped

into the “Registration Slot “ and seats firmly. ( Fig. 12) The entire motor

body should not rotate if this is done correctly.

WARNING: Failure to properly seat the “Check Tab” can damage the

ceiling fan during operation.

HANGING THE FAN (continued)

Fig. 12

Check Tab

Registration Slot

Mounting Bracket

Hanger Ball

56” Almere | 11

Flat Washer

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 13)

Step 2. Insert the safety cable through the mounting bracket and one of the holes in

the outlet box into the ceiling. Adjust the length of the safety cable to reach the screw

and washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the safety

cable over the wood screw and under the washer. Tighten the wood screw securely.

(Fig. 14)

NOTE: Although the safety support cable is required for Canadian installations only,

it’s a good idea to make the attachment with any installation.

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable Bolt

Wood Screw

Fig. 14

Fig. 13

12 | KICHLER.COM

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the power

at the main circuit panel before wiring.

Follow the steps below to connect the fan to your household wiring. Use the wire

connectors supplied with your fan. Secure the connector with electrical tape. Make

sure there are no loose wire stands or connections.

WARNING: If your house wires are dierent colors than referenced in this manual,

stop immediately. A professional electrician is recommended to determine proper

wiring.

Step 1. Insert the receiver into the mounting bracket, with the flat side facing up toward

the ceiling. (Fig. 15)

Step 2. Connect wires using the connectors as shown in WIRE DIAGRAM. (Fig.16)

WARNING: Check to see that all connections are tight, including ground, and that no

bare wire is visible at the wire connections.

Step 3. After the connections have been made, they should be turned upward and

pushed carefully up into the outlet box. The wires should be spread apart with the

grounded conductor (white wires) and the equipment-grounding conductor (green or

bare copper wires) on one side of the outlet box and the ungrounded conductor (black

wires) on the other side of the outlet box.

Fig. 15

Mounting Bracket

Receiver

56” Almere | 13

WIRE DIAGRAM

Fig. 16

AC 120V INPUT

GROUND WIRE

FROM CEILING GROUND WIRE

WHITE (NEUTRAL)

BLACK (MOTOR)

WHITE (“TO MOTOR N”)

BLACK (“TO MOTOR L”)

WHITE (“AC IN N”)

BLACK (“AC IN L”)

RECEIVER

WHITE

BLACK

WALL

CONTROL

BLACK

(“AC IN L”)

BLACK

(“TO MOTOR L”)

GROUND WIRE

BLACK

14 | KICHLER.COM

Outlet Box

Wall Control

Face Plate

Switch

Wall Plate

Fig. 17

Fig. 18

INSTALLING THE WALL CONTROL

WARNING: All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a qualified

licensed electrician.

NOTE: SWITCH INSTALLATION MUST COMPLY WITH ALL LOCAL AND NATIONAL

ELECTRIC CODE.

WARNING: Shut o main power at the circuit breaker or fuse panel before continuing.

Step 1. Remove the existing wall plate and the old switch from the wall outlet box.

Disconnect wires. (Fig. 17)

Step 2. Connect the outlet box wires to the wall control wires, using the wire connectors

provided. (Fig. 18)

*Connect the lead wire (HOT) from the outlet box to BLACK wire marked

“AC IN L” from wall control.

*Connect the lead wire (LOAD) from the outlet box to BLACK wire marked

“TO MOTOR L” from wall control.

*Connect the GROUND from the outlet box to GROUND from wall control.

Step 3. Secure the wires connectors and make sure there are no loose strands or

connections. Carefully tuck wire connections back inside outlet box and secure the

wall control to outlet box with screws provided. Snap the face plate in place on the front

of the wall control.

GROUND WIRE

FROM CEILING

TO LOAD

TO 120V SOURCE

HOT

BLACK (AC IN L)

BLACK (TO MOTOR L)

GROUND

56” Almere | 15

COMPLETING THE FAN INSTALLATION

Step 1. Remove one of the two shoulder screws in the mounting bracket.

Loosen the second shoulder screw without fully removing it. (Fig. 19)

Step 2. Assemble canopy by rotating key slot in canopy over shoulder

screw in mounting bracket. Reinstall the shoulder screw that was previously

removed, then retighten two shoulder screws securely. (Fig. 20)

Step 3. Securely attach and tighten the canopy hole cover over the shoulder

screws in the mounting bracket utilizing the keyslot twist-lock feature.(Fig.21)

Mounting

Bracket

Shoulder

Screw

Shoulder

Screw

Canopy

Canopy Hole Cover

Fig. 20

Fig. 19

Fig. 21

16 | KICHLER.COM

OPERATING INSTRUCTIONS

ACTIVATING THE LEARNING PROCESS

NOTE: The control system for this fan is equipped with a learning frequency function which has 56K

code combinations to prevent potential interference from other remote units. The frequency on your

receiver and wall control unit has been preset at the factory. No frequency change is necessary. If

the fan is non-functional or if you desire to install another fan within the same area with a separate

frequency code, follow the instructions below.

1.Use a small flat screw driver and gently pry the faceplate apart from the top of wall control. (Fig. 22)

2.After installation is complete, press and hold the LEARN button for 3 seconds within 30 seconds

after AC power is turned on. Fan will turn on at medium speed and light (if installed) will turn on. This

confirms that the SMART SYNC setting is active and OK.

3.If you cannot finish the setting within the 30 seconds time frame, the main power must be turned

o and re-started again. This will repeat step 1 until the LEARN feature is activated as indicated.

LIGHT FUNCTION SELECTION SWITCH (Fig. 22)

D means “Dimmer”

O means “only on/o, no dimmer”

The light of this fan is dimmable, it has been set to “D” position at factory. If you want the light to be

only ON/OFF, slide the switch to “O” position.

NOTE: The “LIGHT FUNCTION SELECTION SWITCH” is N/A for this fan. This fan does not

include a light kit or lamps.

WALL CONTROL OPERATION(Fig. 23)

ON/OFF: Active and lock the wall control

HI : High speed

MED: Medium speed

LOW: Low speed

FAN OFF: Turn o the fan

LIGHT: Turn light ON or OFF. Press and hold the button to set desired brightness.

NOTE: The “LIGHT” button is N/A for this fan. This fan does not include a light kit or lamps.

Fig. 22

Fig. 23

Faceplate

Light function selection switch

LEARN

56” Almere | 17

Fig.25

Fig.24

Fig. 26

REVERSE FUNCTION

To operate the reverse function on this fan, slide the reverse switch

(Fig.24) to the opposite position.

WARNING: Do not operate reversing switch while fan blades are

in motion. Fan must be turned o and blades stopped before

reversing blade direction.

Warm Weather Operation: Warm Weather Operation: Forward (counter clockwise).A downward

airflow creates a cooling eect (Fig.25). This allows you to set your air

conditioner on a warmer setting without aecting your general comfort.

Cool Weather Operation: Cool Weather Operation: Reverse (clockwise). An upward airflow

moves warm air o of the ceiling (Fig. 26). This allows you to set your

heating unit on a cooler setting without aecting your general comfort.

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.)This device may not cause harmful interference, and

2.)This device must accept any interference received, including interference that may cause undesired operation.

Note: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician or help.

18 | KICHLER.COM

TROUBLESHOOTING

ProblemProblem

Fan will not start.Fan will not start.

Fan sounds noisy.Fan sounds noisy.

Fan wobble.Fan wobble.

Remote control Remote control

malfunction.malfunction.

SolutionSolution

1. Check circuit fuses or breakers.1. Check circuit fuses or breakers.

2. Check all electrical connections to ensure proper contact.2. Check all electrical connections to ensure proper contact.

CAUTION: Make sure the main power is OFF when checking any electrical connection.CAUTION: Make sure the main power is OFF when checking any electrical connection.

1. Make sure all motor housing screws are snug.1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are tight.2. Make sure the screws that attach the fan blade brackets to the motor are tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing. 3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is o.CAUTION: Make sure main power is o.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are not 5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are not

touching any other component.touching any other component.

6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors or 6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors or

remote controls.remote controls.

7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.

1. Check that all blade and blade arm screws are secure.1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the 2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the

ceiling above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for ceiling above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for

measurement. Repeat for each blade. The distance deviation should be equal within 1/8".measurement. Repeat for each blade. The distance deviation should be equal within 1/8".

3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and 3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and

possibly result in smoother operation. possibly result in smoother operation.

1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT 1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT

a basic On/o wall switch, if desired.a basic On/o wall switch, if desired.

KICHLER LIGHTING LLC

30455 SOLON RD.

SOLON, OH 44139 USA

CUSTOMER SERVICE 866.558.5706

8:00 AM TO 5:00 PM EST, MONDAY - FRIDAY

REV. 02-10-2023

www.kichler.com

Les images du produit peuvent varier légèrement par rapport au produit réel.

Almere de 56 po

MANUEL D’INSTRUCTIONS

Modèle n° 330130LISEZ ET CONSERVEZ CES INSTRUCTIONS

La page charge ...

Kichler 330130 Guide d'installation

Kichler 330130 Guide d'installation

dans d''autres langues