Chief CMA348 Guide d'installation

Catégorie
Mur
Taper
Guide d'installation

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
XL Vibration Dampener Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
CMA348
CMA348 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure that all components
located between the CMA-348 up to (and including) the
projector system weighs between 35 - 100 lbs (15.9 - 45.4 kg).
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this accessory outdoors.
IMPORTANT ! :
The CMA348
accessory
is designed to be
mounted to a 1-1/2" NPT or NPSM threaded extension column
(not included).
NOTE: The CMA348 will fit within a 2’ x 2’ ceiling tile.
--SAVE THESE INSTRUCTIONS--
Installation Instructions CMA348
3
DIMENSIONS
LEGEND
DIMENSIONS: INCHES
[MILLIMETERS]
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
CMA348 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/16"
3/32"
(included)
A (1)
[CMA348]
B (1)
3/32"
C (2)
10-24 x 1/4"
Installation Instructions CMA348
5
PREPARING FOR INSTALLATION
NOTE: The following instructions assume that a suitable
ceiling plate (not included) has been properly installed
following instructions included with the ceiling plate.
It is also assumed
that a 1-1/2" NPT or NPSM
threaded extension column (not included) is properly
installed in the ceiling plate.
CAUTION: WEIGH ALL PARTS BEFORE BEGINNING
INSTALLATION! Determine if the total combined weight of
the projector, projector mount, and lower mounting column
(projector system) is less than, or more than, 50 lbs (22.7 kg)
before proceeding with the installation.
IMPORTANT ! :
The CMA348 is shipped ready-to-install
for projector systems weighing between 35-50 lbs
(22.7 kg). For projector systems weighing 51-100 lbs
(22.7 - 45.4 kg), slight adjustments may be needed. (See
Adjustments
section for further information.)
NOTE: In order to optimize the CMA348 vibration dampening,
keep the CMA348 as close as possible to the projector
by minimizing the length of the lower extension column.
NOTE: For optimal CMA348 performance, the projector
system’s center of gravity should be centered on the
upper mounting column.
INSTALLATION
1. Thread top of CMA348 mount (A) onto NPT 1-1/2” upper
mounting column. (See Figure 1)
NOTE: Ensure there is no direct contact between mount and
surrounding structure. Any contact could allow
vibration transfer to the projector.
2. Secure NPT 1-1/2” upper mounting column to CMA348
mount (A) using one 10-24 x 1/4" set screw (C). Turn set
screw (C) until it contacts thread of NPT 1-1/2” upper
mounting column. (See Figure 1)
3. Thread NPT 1-1/2” lower mounting column (not included)
into bottom of CMA 348 mount (A). (See Figure 1)
4. Secure NPT 1-1/2” lower mounting column to CMA348
mount (A) using one 10-24 x 1/4" set screw (C). Turn set
screw (C) until it contacts thread of NPT 1-1/2” lower
mounting column. (See Figure 1)
5. Thread projector mount (not included) onto lower NPT 1-1/2"
lower mounting column. (See Figure 1)
6. Secure NPT 1-1/2” lower mounting column to projector
mount following the installation instructions provided with
the projector mount (not included). (See Figure 1)
7. Attach projector to projector mount following the installation
instructions provided with the projector mount (not
included).
Figure 1
ADJUSTMENTS
NOTE: If the entire projector system weighs between 51 and
100 lbs (
22.7 - 45.4 kg) some minor adjustments may be
necessary to optimize the vibration dampening quality of
the CMA348.
1
Upper
mounting
column
Ceiling
plate
(A)
(C) x 1
2
(C) x 1
4
Lower
mounting
column
3
Projector mount
Projector
5
7
CMA348 Installation Instructions
6
1. Tighten nut at bottom of each of the three springs two full
turns while holding bolt at top of each spring. Be sure this
is done in a uniform manner. (See Figure 2)
Figure 2
1
x 3
[Viewed from below CMA348]
Hold while
tightening nuts
at bottom of
springs
Installation Instructions CMA348
7
CMA348 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-003084 Rev00
2018 Milestone AV Technologies
www.milestone.com
09/18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief CMA348 Guide d'installation

Catégorie
Mur
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues