Senco DS530 Series Manuel utilisateur

Marque: Senco

Modèle: DS530 Series

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

KYOCERA-SENCO Industrial Tools, Inc.

8450 Broadwell Road

Cincinnati, OH 45244

1-800-543-4596

NFD810X • Issued June 13, 2021

DS530 Series

AUTO-FEED SCREW

SYSTEM ATTACHMENT

Operating Instructions

IMPORTANT:

Read before use.

Table of Contents

General Power Tool Safety Warnings ...................................................................................... 4

Work Area Safety ................................................................................................................... 4

Electrical Safety ..................................................................................................................... 4

Personal Safety ..................................................................................................................... 4

Power Tool Use and Care ...................................................................................................... 5

Service .................................................................................................................................. 5

Functional Description ............................................................................................................. 6

Tool Operation .......................................................................................................................... 7

Installing a DS530 Attachment .............................................................................................. 7

Adjusting for Fastener Length ............................................................................................... 8

Loading the Tool .................................................................................................................... 9

Depth of Drive Adjustment .................................................................................................... 9

Driving Screws ...................................................................................................................... 9

Reverse Operation ............................................................................................................... 10

Bit Replacement .................................................................................................................. 10

Nosepiece Replacement ...................................................................................................... 10

Installing the Extension Pole ............................................................................................... 11

Maintenance .......................................................................................................................... 12

Accessories ............................................................................................................................ 12

Technical Speciﬁcations ........................................................................................................ 12

Troubleshooting ..................................................................................................................... 13

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated

with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates a hazardous situation, which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a hazardous situation, which, if not avoided, could result in

death or serious injury.

CAUTION: Indicates a hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE: (Without Safety Alert Symbol) indicates information considered im-

portant, but not related to a potential injury (e.g. messages relating

to property damage).

Some of the following symbols may be used on this product. Please study them and learn their meaning.

Proper interpretation of these symbols will allow you to operate the product in a better, safer manner.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s

Manual

To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Eye Protection Always wear eye protection with side shields marked to comply with

ANSI Z87.1.

Wet Conditions

Alert

Do not expose to rain or use in damp locations.

No Hands Failure to keep your hands away from blade will result in serious

personal injury.

Recycle This product uses Litium-ion batteries. Local, state, or federal laws

may prohibit disposal of batteries in ordinary trash. Consult your

local waste authority for information regarding available recycling

and or disposal options.

VVolts Voltage

min Minutes Time

Direct Current Type or characteristic of current

Alternating

Current

Type or characteristic of current

noNo Load Speed Rotational speed, at no load

.../min Per Minute Revolutions, strokes, surface speed, orbits, etc. per minute

General Power Tool Safety Warnings

WARNING

Read all safety warnings, instructions, illustrations and speciﬁcations pro-

vided with this power tool. Failure to follow all instructions listed below may result in electric

shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

WORK AREA SAFETY

1. Keep your work area clean and well lit. Cluttered or dark areas promote accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable liquids,

gases, or dust. Power tools create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

4. The included auto-feed screwdriver attachment was designed to work with one make and several

models of power screwdrivers. Refer to the screwdriver manufacturer’s operator’s manual for related

safety and operating instructions.

ELECTRICAL SAFETY

5. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodiﬁed plugs and matching outlets will reduce risk of

electric shock.

6. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigera-

tors. There is an increased risk of electric shock if your body is earthed or grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

8. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

9. When operating a power tool outdoors, use an extension cord suitable for outdoor use. If operating

a power tool in a damp location is unavoidable, use a RESIDUAL CURRENT DEVICE (RCD) protected

supply. Use of a cord suitable for outdoor use reduces the risk of electric shock.

10. Hold power tool using its insulated gripping surfaces when performing an operation where the fastener

may come into contact with hidden wiring. Fasteners that come into contact with a “live” wire may make

exposed metal parts of the power tool “live” and could give the operator an electric shock.

11. If operating a power tool in damp location is unavoidable, use a Residual Current Devise (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

NOTE: the term “Residual Current Devise (RCD)” may be replaced by the term “Ground Fault Circuit

Interrupter (GFCI)” or “Earth Leakage Circuit Breaker (ELCB)”.

PERSONAL SAFETY

12. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use

a power tool while you are tired or under the inﬂuence of drugs, alcohol, or medication. A moment of

inattention while operating power tools may result in serious personal injury.

13. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce

personal injuries.

14. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your ﬁnger on the

switch or energizing power tools that have the switch on promotes accidents.

15. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal injury.

16. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power

tool in unexpected situations.

17. Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving

parts. Loose clothes, jewelry or long hair can be caught in moving parts.

18. If devices are provided for dust extraction and collection, ensure these are connected and properly

used. Use of dust collection can reduce dust-related hazards.

19. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool

safety principles. A careless action can cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

20. Do not force the power tool. Use the correct power tool for your application. The correct power tool will

provide better safer results when used according to its speciﬁcations.

21. Do not use the power tool if the power switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

22. Disconnect the plug from the power source and/or remove the BATTERY pack, if detachable, from the

power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

23. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained

users.

24. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by poorly maintained power tools.

25. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

26. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into

account the working conditions and the work to be performed. Use of the power tool for operations

different from its intended purpose could result in a hazardous situation.

27. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

SERVICE

28. Have your power tool serviced by a qualiﬁed repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

29. Users or full-service dealers need to be aware that a spring is housed inside the feed system.

It will release from its constrained position during disassembly. Normal precautions should apply.

GENERAL POWER TOOL SAFETY WARNINGS

Functional Description

Extension Pole Handle

Stand-Up Extension Pole Strip Guide Track

Detachable Feed System

Locking Clamp

Slide Body Loading Point

Tool-less Nose Piece

Adjustment Pin

Nose Piece

Retention Screw

Depth of Drive

Indicator

Depth of Drive

Lock Button

Depth of Drive

Adjustment Knob

Tool Operation

Read sections titled “Safety Warnings” before operating tool.

WARNING

Do not use this product if it is not completely assembled or if any parts

appear to be missing or damaged. Use of a product that is not properly and completely

assembled or with damaged or missing parts could result in serious personal injury.

WARNING

Do not attempt to modify this product or create accessories or attachments not

recommended for use with this product. Any such alteration or modiﬁcation is misuse

and could result in hazardous conditions possibly leading to serious personal injury.

If any parts are damaged or missing, please call 1-800-543-4596 for assistance.

MODEL ADAPTER COMPATIBLE TOOLS

DS530-S1 MB0184 SENCO • SG2510, SG4100

DS530-M1 MB0186 MAKITA • FS2200, FS2500, FS4200, FS6200, XSF03, XSF04, XSF05

DS530-D1 MB0183 DEWALT • DW252, DW253, DW255, DW257, DW266, DW272, DW276

MB0185 DEWALT • DCF624

SOLD SEPARATELY MB0187 MAKITA • FS2701

INSTALLING A DS530-S1 OR DS530-M1 ADAPTER AND ATTACHMENT

1. Unplug tool from electrical supply or remove battery before installing attachment.

2. Remove the manufacturer’s nose cone from the tool.

3. Remove manufacturer’s bit and holder if present.

4. Choose the adapter which matches the screwdriver model and brand you are using.

5. Attach the adapter onto the screwdriver ensuring it is fully seated and secure, tighten all set screws.

NOTE: If you want to use an extension pole with the attachment, install that, now. See instructions for

using the extension pole on page 11. Otherwise, continue to next step, below.

6. Install the appropriate Senco bit, making sure it is fully seated (this may require some force.)

7. Slide the attachment onto the adapter. Make sure there’s no gap between the attachment and the adapter.

Tighten clamp. Adjust the screw with a 2.5mm hex key if necessary to provide more or less clamping

force. This should only be tightened enough to prohibit the attachment from easily rotating on the adapt-

er or sliding off with minimal force. Over-tightening will only make it harder to unlock the clamp during

removal and could damage clamp components.

Locked Unlocked Bit Type DS530

EA0314 Phillips

EA0315 Square

EA0316 Rex

TOOL USE

INSTALLING THE DS530-D1 OR DS530-D2 ADAPTER AND ATTACHMENT

1. To prepare the screw gun before installing the screw-on adapter.

Adapter

DeWalt Tool

Output Shaft

Assembly

a. Unplug tool from electrical supply or remove battery before installing attachment.

b. Remove the nose cone.

c. Remove manufacturer’s bit and holder if present.

d. Unscrew the stock DeWalt clutch housing by rotating clockwise (threads are left-hand/reversed). The

use of a wrench may be necessary.

e. Remove the output shaft assembly from the stock clutch housing and reinstall into the supplied Senco

adapter.

f. Thread adapter onto the DeWalt tool by rotating counterclockwise.

g. Torque adapter onto tool to 50 in. lbs. with an adjustable wrench.

2. Install the bit and the attachment onto the tool as described in steps 6-7 in the previous section.

ADJUSTING FASTENER LENGTH

1. Unplug tool from electrical supply or remove battery before adjusting nose-piece for fastener length.

2. Depress the screw selector pin until it is ﬂush with nosepiece and slide the nosepiece to the desired

setting by aligning hatch marks with the silver adjustment pin.

3. Release pin ensuring it is fully engaged in selected nosepiece slot for proper operation.

Nosepiece has these possible settings:

DS530

1" 1 1/4” 1 1/2” 1 5/8” 1 3/4” 2” 2 1/4” 2 1/2” 2 3/4” 3”

TOOL USE

LOADING THE TOOL

CAUTION

Beware of sharp points on screws. Avoid grabbing this area during loading and

operation.

11. Make sure the heads of the screws are resting on top of the plastic colla-

tion material.

This will ensure proper strip advancement and prevent jamming.

2. Check for proper fastener length setting (see “Adjusting for Fastener

Length” above).

3. Feed the strip into the strip guide up toward the nose of the tool.

4. Feed the strip into the slide body until the ﬁrst screw is aligned with the bit. The tool will feed all

subsequent screws automatically as the tool is pulled back off the work surface, returning to its

relaxed state.

5. To remove the strip, pull it through from the top of the nosepiece.

ADJUSTING DEPTH OF DRIVE

1. This tool is equipped with a locking depth-control adjustment.

2. Depress the lock switch to release the thumbwheel and rotate it to a notched position. Adjust the

amount of countersink by turning the thumbwheel clockwise to go more shallow, or counter-clock-

wise to go deeper. Release the lock button after adjustment, and make sure the thumbwheel is

locked into a notched position.

3. Test drive screws while adjusting until the desired countersink is reached.

DRIVING SCREWS

1. Whenever possible, hold the tool at a right angle (perpendicular) to the work surface.

2. Pull the trigger to start the motor.

3. Press the nosepiece with constant force against the work surface. Do not remove the tool from the

work surface until the clutch disengages and the bit stops rotating, signalling a fully driven screw.

4. Continue to allow the motor to run. The next screw will be automatically fed into place when the tool

is pulled off the work surface.

TOOL USE

REVERSE OPERATION

To operate tool in reverse for removal of screws (refer to Figure 1):

1. Flip the forward/reverse switch on the tool to reverse rotation.

2. Rotate the clamp on the attachment to the unlock position.

3. Slide the attachment off the tool to expose the bit.

4. Insert bit into screw and apply/maintain pressure to engage clutch.

5. Pull trigger until screw is completely disengaged.

BIT REPLACEMENT

Due to wear or damage, the bit will need to be replaced periodically or when changing screw recess type.

CAUTION

Remove battery or unplug tool before attempting to replace the bit.

1. Turn the clamp on the attachment to the unlock position.

2. Slide the attachment off the tool to expose the bit.

3. Remove bit per tool manufacturer’s instructions

4. Insert the new bit per tool manufacturer’s instructions.

5. Install attachment and rotate clamp to lock position.

NOSEPIECE REPLACEMENT

1. Remove battery or unplug the tool before changing the

nosepiece.

2. Remove retention screw.

3. Set the nosepiece on the longest setting possible.

4. Depress the screw selector pin until it is completely de-

pressed. It will be necessary to use a screw or thin object to

depress to this depth.

5. While holding the pin in this position, slide the nosepiece

forward and off the slide body.

6. Install the new nosepiece.

7. Replace the nosepiece retention screw ensuring it is seated

snug against the slide body.

8. Check for proper fastener length setting (see “Adjusting for

Fastener Length” above).

TOOL USE

INSTALLING THE EXTENSION POLE

To prepare the screwgun for using the extension pole:

1. Remove the nose cone.

2. Remove bit holder assembly.

3. Attach adapter. (See page 7-8 for details.)

4. Tighten set screws. (See page 7-8 for details.)

5. Remove the extension pole drive shaft from inside the extension pole, and insert it into the tool.

Push it in until you hear it snap into place.

6. Slide the extension pole shell down onto the drive shaft.

Thread the extension pole on to the adapter until it’s all the way down and hand-tight.

7. The handle should slide over and down the pole. Place the collar over the bottom of extension pole

just above the adapter. Tighten by spinning the handle clockwise in the desired orientation. (Do not

overtighten).

8. Insert the bit into the end of the extension pole.

9. Slide the attachment down over the top of the bit. Pull it on tight, making sure there’s no gap.

10. Tighten clamp. Adjust the screw if necessary to provide more or less clamping force. This should

be tight enough to prohibit the attachment from easily rotating on the adapter or sliding off with

minimal force.

11. Set nosepiece for the length of screws to be driven. (See Adjusting Fastener Length, on page 8)

12. Set depth of drive for the desired amount of countersink. (See Adjusting Depth of Drive on page 9)

The attachment is now installed and you are ready to load in a screw strip and begin driving screws.

Load the tool and drive screws as described on page 9.

Maintenance

Read section titled “Safety Warnings” before maintaining tool.

1. With battery removed or cord disconnected, make daily inspection to ensure free movement of

nosepiece and trigger.

Do not use tool if nosepiece or trigger sticks or binds.

2. Lubrication of the feed system is not necessary. DO NOT OIL.

3. Wipe tool clean daily and inspect for wear, especially the bit and nosepiece. Replace as necessary.

WARNING

Repairs other than those described here should be performed only by trained,

qualiﬁed personnel. Contact SENCO for information at 1-800-543-4596.

Accessories

SENCO offers a full line of DuraSpin screws and accessories for your SENCO tools, including:

• Bits

• Storage Bag

• Assorted Nosepieces

• Safety Glasses

For more information or a fully illustrated catalogue of Senco accessories, contact your sales

representative or call Senco at 1-800-543-4596.

Technical Speciﬁcations

SPECIFICATION DS530 DS530-S1/DS530-D1/

DS530-M1

DS532/DS534

WEIGHT 1.65 LBS. (.75 KG) 3.5 LBS. (1.6 KG) 7 LBS. (3.2 KG)

HEIGHT 3.5" (89 MM) 3.5" (89 MM) 7" (178 MM)

LENGTH 22" (556 MM) MAX 33" (838 MM) MAX 40.5" (1029 MM) MAX

WIDTH 2.75" (70 MM) 2.75" (70 MM) 2.75" (70 MM)

FASTENER CAPACITY 50 SCREWS (1 STRIP) 50 SCREWS (1 STRIP) 50 SCREWS (1 STRIP)

FASTENER LENGTH 1-3" 1-3" 1-3"

FASTENER RANGE #6-#12 #6-#12 #6-#12

Troubleshooting

Problem/Symptom Probable Cause Corrective Action

Tool will not fully drive fastener Bit is worn Replace bit

Power capabilities of the tool have

been exceeded Discontinue use in that application

Tool is in reverse Switch tool to forward

Incorrect bit installed Ensure correct bit type and length

are installed

Depth of drive not set properly See p. 9 for proper adjustment

Tool does not advance fastener Screw length is improperly set See p. 8-9 for proper adjustment

Return spring is weak Replace or return to authorized

service center for repair

Defective collation material Use Senco branded fasteners for

optimum performance

Defective slide body Replace or return to Senco autho-

rized service center for repair

Screw strip is jammed in guide

track Ensure strip slides free in guide

track

Screws “kick out” or misdrive

during use Screw length improperly set See p. 9-10 for proper

adjustment

Incorrect bit installed Ensure correct bit type and length

are installed

Defective or damaged feed system Return to Senco Authorized

service centre for repair

Bit slips off screw or screw is

driven at an angle Tool slid forward during drive Hold tool ﬁrmly while driving

Bit is worn or broken Replace bit

Nosepiece is worn or damaged Replace or return to Senco autho-

rized service centre for repair

Fastener jams Screw length improperly set See p. 9-10 for proper

adjustment

Defective collation material Use Senco branded fasteners for

optimum performance

Nosepiece damaged or bent Replace nosepiece

Screw partially driven into collation

material then feed system released Remove jammed screw with

ﬁngers or pliers and resume use

Slide mechanism ”sticks” or

returns slowly Debris build-up in mechanism Clean mechanism

Weak return spring Replace or return to Senco

authorized service centre for repair

Bit sticking in collation material Use Senco branded fasteners for

optimum performance

Always attempt to store screws

in cool, dry place before use.

Overheated collation can get soft

and cause a delay in feed system

return

Pushing force becomes excessive Improper screw for application Consider alternative fastener

CAM screw is loose or damaged Tighten or replace CAM screw

Debris build-up on mechanism Clean mechanism

Attachment will not fully

install/lock The attachment is not fully insert-

ed and seated onto the tool Verify that the attachment is fully

seated before attempting to lock

the collar

The clamp is not turned to the full

unlock position Rotate the clamp to full unlock

position

Foreign object stuck inside

attachment Make sure that no objects or parts

are jammed inside the connection

Components in connector may be

damaged Replace connector or return to

Senco Authorized service centre

for repair

Attachment will not fully

uninstall/unlock The clamp is not turned to the full

unlock position Rotate the clamp to full unlock

position

The attachment is catching on the

front end of the tool Avoid removing at any angle, pull

attachment straight off and away

from the tool to remove

When in full unlock position,

maneuver attachment up and

down to disengage grabbing

features from tool

Foreign object stuck inside

attachment Be sure that no objects or parts

are jammed inside the connection

Components in connector may be

damaged Replace connector or return to

Senco Authorized service centre

for repair

Limited Warranty

SENCO® Pneumatic, DuraSpin®, Cordless Tools

& Compressors

KYOCERA-SENCO Industrial Tools, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship.

SENCO warrants to the original retail purchaser that the following products will be free from defects in material or workmanship for the warranty period

Products New Reconditioned Products New Reconditioned

Pneumatic Tools ÜFive Years One Year Air Compressors One Year 90 Days

Fusion Tools Two Years Six Months Combo Kit Tools One Year 90 Days

Gas Tools Two Years Six Months Multi-Blow Hand Nailers One Year 90 Days

Duraspin Tools Five Years 90 Days Stapling Hammers One Year 90 Days

Ü = Both XP and Pro Series

During the warranty period (which begins on the purchase date), SENCO will repair or replace, at SENCO’s option and expense, any product or part

that is defective in materials or workmanship after examination by a SENCO Authorized Warranty Service Centre, subject to the exceptions, exclusions

and limitations described below. Any replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced

product or part. A DATED SALES RECEIPT OR PROOF OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A

WARRANTY CLAIM. Warranty registration is also required and can be accomplished through on-line Product Registration at www.senco.com or by

completing and returning the postage paid warranty registration form included with your Operator’s manual/parts chart information, found inside the

product carton. To make a warranty claim, you must return the product, with proper receipt/proof of purchase and return transportation charges prepaid,

to a SENCO Authorized Warranty Service Centre. A list of SENCO Authorized Warranty Service Centres can be found at www.senco.com or by calling

1-800-543-4596 toll free. SENCO will perform its obligations under this warranty within a reasonable time after approval of the warranty claim.

SENCO Cordless:

1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the SENCO Cordless tool will be free from defects

in materials and workmanship for two years after the purchase date.

2. SENCO warrants that the batteries and chargers used with SENCO Cordless tools will be free from defects in material and workmanship for

one year after the purchase date.

Warranty Exclusions

The following warranty exclusions apply:

seals, driver blades, piston stops, and piston/driver assembly.

2. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, accidents, operation beyond the recommended

speeds or voltage (electric units only), improper storage, or damage resulting from shipping.

3. Prod

4. Labour charges or loss or damage resulting from improper operation, maintenance or repairs are not covered by this warranty.

General Warranty Conditions

This warranty will be honoured only if:

A. Clean, dry, regulated compressed air has been used, at air pressure not exceeding the maximum indicated on the tool casting;

B. No e

C. No d

maintenance instructions).

THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT, AND SENCO DISCLAIMS ALL OTHER WARRANTIES. ANY IMPLIED WAR-

RANTIES WILL BE LIMITED IN DURATION TO THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. SOME STATES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. YOUR REMEDIES ARE

SOLELY AND EXCLUSIVELY AS STATED ABOVE. SENCO SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,

OR SPECIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,

SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,

WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL SENCO’S LIABILITY EXCEED THE PRICE OF THE PRODUCT WHICH

HAS GIVEN RISE TO THE CLAIM OR LIABILITY. ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE

EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE. NO EMPLOYEE OR REPRESENTATIVE OF SENCO OR ANY DISTRIBUTOR OR

DEALER IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.

Replacement of Tool Due to Natural Disaster

Such a claim will be honoured provided that the original retail purchaser had previously submitted a completed warranty registration card for the tool,

and then submits proof of ownership and an acceptable statement describing such Act of God documented by an insurance carrier, police department,

Customer Satisfaction

If for any reason the product does not perform to the original purchaser’s satisfaction, it can be returned to the place of purchase within thirty days with

dated sales receipt for a full refund of the purchase price (applies to new product sales only).

CINCINNATI, OHIO 45244-1611 USA

www.senco.com

160101

KYOCERA-SENCO Industrial Tools, Inc.

8450 Broadwell Road

Cincinnati, OH 45244

1-800-543-4596

KYOCERA-SENCO Industrial Tools, Inc.

8450 Broadwell Road

Cincinnati, OH 45244

1-800-543-4596

KYOCERA-SENCO Industrial Tools, Inc.

8450 Broadwell Road

Cincinnati, OH 45244

1-800-543-4596

NFD810X • Emitido el 13 de junio de 2021

Serie DS530

ADITAMENTO DEL SISTEMA DE

ALIMENTACIÓN AUTOMÁTICA

DE TORNILLOS

Instrucciones de operación

IMPORTANTE:

Lea este documento

antes de utilizar la

herramienta.

Índice

Advertencias generales de seguridad al usar herramientas eléctricas ..................................................4

Seguridad en el área de trabajo .............................................................................................................. 4

Seguridad con la electricidad .................................................................................................................4

Seguridad personal ................................................................................................................................4

Uso y cuidado de las herramientas eléctricas ........................................................................................5

Servicio ..................................................................................................................................................5

Descripción funcional ...............................................................................................................................6

Operación de la herramienta .................................................................................................................... 7

Instalación del aditamento DS530 ..........................................................................................................7

Ajuste de la longitud del sujetador .........................................................................................................8

Carga de la herramienta .........................................................................................................................9

Ajuste de la profundidad a la que se introducen los tornillos .................................................................9

Inserción de los tornillos ........................................................................................................................9

Operación inversa ................................................................................................................................10

Reemplazo de la broca ......................................................................................................................... 10

Reemplazo de la punta ......................................................................................................................... 11

Instalación del poste de extensión .......................................................................................................11

Mantenimiento ........................................................................................................................................ 12

Accesorios ............................................................................................................................................... 12

Especiﬁcaciones técnicas ....................................................................................................................... 12

Solución de problemas ...........................................................................................................................13

SÍMBOLOS

Las siguientes palabras de señalización y signiﬁcados tienen la intención de explicar los niveles de riesgo

asociados con este producto.

SÍMBOLO SEÑAL SIGNIFICADO

PELIGRO: Indica una situación peligrosa que, si no se evita, provocará la

muerte o lesiones graves.

ADVERTENCIA: Indica una situación peligrosa que, si no se evita, puede provocar la

muerte o lesiones graves.

PRECAUCIÓN: Indica una situación peligrosa que, si no se evita, puede provocar

lesiones leves o moderadas.

AVISO: (Sin símbolo de alerta de seguridad) indica información que se

considera importante, pero no está relacionada con una posible

lesión (por ejemplo, mensajes relacionados con daños a la

propiedad).

Se pueden usar algunos de los siguientes símbolos en este producto. Estúdielos y aprenda su signiﬁcado.

La interpretación adecuada de estos símbolos le permitirá operar el producto de una manera mejor y más

segura.

SÍMBOLO NOMBRE DESIGNACIÓN O EXPLICACIÓN

Alerta de seguridad Indica un posible riesgo de lesiones personales.

Lea el manual del

operador

Para reducir el riesgo de lesiones, el usuario debe leer y entender el

manual del operador antes de usar este producto.

Protección para los

ojos

Siempre use protección para los ojos con guardas laterales que

tenga la marca de que cumple con ANSI Z87.1.

Alerta de

condiciones de

humedad

No exponga la herramienta a la lluvia ni la use en lugares húmedos.

No acerque las

manos

Mantenga las manos lejos de la cuchilla, de lo contrario, podría sufrir

una lesión personal grave.

Reciclaje Este producto utiliza baterías de iones de litio. Las leyes locales,

estatales o federales pueden prohibir que se desechen las baterías

en la basura ordinaria. Consulte a su autoridad local de residuos

para obtener información sobre las opciones disponibles de reciclaje

y desecho.

VVoltios Voltaje

min Minutos Tiempo

Corriente continua Tipo o característica de la corriente

Corriente alterna Tipo o característica de la corriente

no Velocidad sin carga Velocidad de rotación, sin carga

.../min Por minuto Revoluciones, golpes, velocidad superﬁcial, órbitas, etc. por minuto

Advertencias generales de seguridad

al usar herramientas eléctricas

Lea todas las advertencias de seguridad, instrucciones, ilustraciones y

especiﬁcaciones que se le proporcionan con esta herramienta eléctrica. El incumplimiento de todas las

instrucciones enumeradas a continuación puede provocar descargas eléctricas, incendios o lesiones graves.

Guarde todas las advertencias e instrucciones para una consulta posterior.

El término “herramienta eléctrica” en las advertencias se reﬁere a una herramienta eléctrica que funciona

con la red eléctrica (con cable) o a una que funciona con una batería (inalámbrica).

SEGURIDAD EN EL ÁREA DE TRABAJO

1. Mantenga su área de trabajo limpia y bien iluminada. Las áreas desordenadas u oscuras promueven accidentes.

2. No opere herramientas eléctricas en atmósferas explosivas, por ejemplo, en presencia de polvo, gases o líquidos

inﬂamables. Las herramientas eléctricas crean chispas que pueden encender el polvo o los vapores.

3. Mantenga alejados a los niños y las personas que estén en los alrededores mientras opera una herramienta

eléctrica. Las distracciones pueden hacer que pierda el control.

4. El aditamento de destornillador de alimentación automática incluido fue diseñado para funcionar con una marca y

varios modelos de destornilladores eléctricos. Consulte el manual del operador del fabricante del destornillador para

obtener instrucciones de seguridad y operación relacionadas.

SEGURIDAD CON LA ELECTRICIDAD

5. Los enchufes de las herramientas eléctricas deben coincidir con el tomacorriente. No haga ningún tipo de

modiﬁcación al enchufe. No utilice la herramienta eléctrica conectada a tierra con un enchufe adaptador. Los

enchufes no modiﬁcados y los tomacorrientes correspondientes reducirán el riesgo de una descarga eléctrica.

6. Evite el contacto del cuerpo con las superﬁcies conectadas a tierra, como tuberías, radiadores, estufas y

refrigeradores. Existe un mayor riesgo de descarga eléctrica si su cuerpo está conectado a tierra.

7. No exponga las herramientas eléctricas a la lluvia o a condiciones de humedad. Si le entra agua a una herramienta

eléctrica aumentará el riesgo de una descarga eléctrica.

8. No maltrate el cable. Nunca use el cable para transportar, jalar o desenchufar la herramienta eléctrica. Mantenga

el cable alejado del calor, aceite, bordes aﬁlados o piezas móviles. Si el cable está enredado o dañado, aumenta el

riesgo de una descarga eléctrica.

9. Cuando opere una herramienta eléctrica en exteriores, use un cable de extensión adecuado para uso en exteriores.

Si es inevitable utilizar una herramienta eléctrica en una ubicación húmeda, utilice un suministro protegido por un

DISPOSITIVO DE CORRIENTE RESIDUAL (RCD). El uso de un cable adecuado para uso en exteriores reduce el riesgo

de una descarga eléctrica.

10. Sujete la herramienta eléctrica utilizando las superﬁcies de agarre aisladas cuando realice una operación en la que

el sujetador pueda entrar en contacto con cables ocultos. Los sujetadores que entran en contacto con un cable que

lleva energía pueden hacer que las partes metálicas expuestas de la herramienta eléctrica “se energicen” y podrían dar al

operador una descarga eléctrica.

11. Si es inevitable utilizar una herramienta eléctrica en una ubicación húmeda, utilice un suministro protegido por un

dispositivo de corriente residual (RCD). El uso de un RCD reduce el riesgo de una descarga eléctrica.

SEGURIDAD PERSONAL

12. Manténgase alerta, observe lo que está haciendo y use el sentido común al operar una herramienta eléctrica. No

use una herramienta eléctrica cuando esté cansado o bajo los efectos de drogas, alcohol o medicamentos. Un

momento de falta de atención al operar una herramienta eléctrica puede causar lesiones personales graves.

13. Use equipo de protección personal. Siempre use protección para los ojos. El equipo de protección como una

mascarilla antipolvo, zapatos de seguridad antideslizantes, casco o protección auditiva para condiciones apropiadas

reducirá las lesiones personales.

La page charge ...

Senco DS530 Series Manuel utilisateur

Marque: Senco

Modèle: DS530 Series

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Senco DS530 Series User manual
español: Senco DS530 Series Manual de usuario

Senco DS530 Series Manuel utilisateur

Senco DS530 Series Manuel utilisateur

dans d''autres langues

Documents connexes