ProSeries XVR
QUICK START GUIDE
© 2018 Uniden America Corporation
Irving, Texas
Issue 1, June 2018
Uniden surveillance products are not manufactured and/or sold with the intent to be used for illegal
purposes. Uniden expects consumer’s use of these products to be in compliance with all local,
state, and federal law. For further information on video surveillance and audio recording legal
requirements, please consult your local, state and federal ofcials.
Uniden constantly works on improving our products. This includes updating our documentation
with the latest rmware changes. Go to www.uniden.com to nd the latest version of all
documentation.
© 2018 Uniden America Corporation
All rights reserved.
CONTENTS
QUICK START GUIDE OVERVIEW ........................... 5
HARDWARE INSTALLATION ............................... 5
PREREQUISITES ...............................................5
DEFAULTS ....................................................5
FIRMWARE AND DOCUMENTATION UPDATES ......................5
INSTALLATION .......................................... 6
INSTALLATION REQUIREMENTS ..................................6
PRO400X1 ............................................................6
PRO800X2 ............................................................6
PRO1600X2 ...........................................................7
SYSTEM SETUP .......................................... 7
QUICK START GUIDE ATTRIBUTES ................................7
INITIAL SETUP .................................................8
SYSTEM SETUP CHECKLIST .....................................8
BATTERY ............................................... 9
COMPLIANCE ........................................... 9
FCC PART 15 ..................................................9
IC ...........................................................10
THREE-YEAR LIMITED WARRANTY ........................ 10
5
UNIDEN PROSERIES XVR QUICK START GUIDE
QUICK START GUIDE OVERVIEW
This Quick Start Guide provides basic steps to install and turn up Uniden's ProSeries XVR and
cameras. Refer to ProSeries XVR Technical Installation Guide for detailed procedures.
Uniden's ProSeries XVR systems are multi-channel digital recorders that uses the latest high
resolution technology and modern compression techniques. Screen and menu selections
combined with user input simultaneous monitor, record, backup, and play back new and recorded
video les.Additional storage (HDD drives) maybe added if the system supports it.
HARDWARE INSTALLATION
PREREQUISITES
• Access to standard AC outlet (AC100~240V, 50Hz~60Hz)
• Phillips-head screwdriver may be required
• VGA or HDMI video monitor that supports 1280x1024 and 1920x1080 resolution modes.
• External PoE network switch is recommended to add IP cameras, if required.
• Camera cables if devices purchased separately (only included in Pro Series kits)
• 12VDC power supply required for each camera
• HDMI or VGA cable (HDMI cable included in ProSeries kits)
• External power supply for up to 16 channels
- For 4 and 8 channels: ADP36-S120A30000
Input: 100-240V, 1.0A
Output: 12VDC, 3A
- For 16 channels: ADP060-120500
Input: 100-140VDC, 1.5A
Output: 12VDC, 5A
Use only the recommended power supply.
• Western Digital Purple or Seagate SkyHawk surveillance hard drives
DEFAULTS
• Administrator user name: admin.
• Administrator password: No password; leave blank.
• LAN1 IPv4 address: DHCP auto enabled
• Default video resolution: 1280 x 1024
• Factory-installed hard drives are formatted and ready to record.
• Daylight savings time enabled; however, the start and stop dates should be veried.
FIRMWARE AND DOCUMENTATION UPDATES
Because Uniden strives to provide the latest technology and quality in all of its products, rmware
updates may be available with no prior notice. Check for updates at support.uniden.com/pro-
support. Update the rmware manually either locally or remotely through a web browser.
6
INSTALLATION
INSTALLATION REQUIREMENTS
• Install the device below 2000 meters altitude.
• Install the device in a horizontal position.
Do not install the device in a vertical or tilted position.
• The device's operating temperature range is 32˚F to 104˚F (0˚C to 40˚C).
Do not locate the device in places with high temperature, humidity, dust, or smoke.
• The device is not water-resistant or waterproof. Do not place objects containing liquid such as a
glass or mug on the device.
• In order to ensure normal heat dissipation, install the device in a well-ventilated area.
• Use Uniden's recommended specic surveillance hard disk drives (Western Digital Purple or
Seagate SkyHawk surveillance hard drives) when adding a hard disk drive.
• Verify that the XVR power supply and AC outlet are reliably grounded.
PRO400X1
1
10
9876543
2
1 Audio Out 6 RJ45 Network Port
2 BNC Camera Jacks 7 USB 2.0
3 Audio In 8 Accessories Out
4 HDMI Video Out 9 Power Input
5 VGA Video Out 10 Power Switch
Cameras connect to LAN1 (PoE gigabit network switch)
PRO800X2
1
10
98765432
1 BNC Camera Jacks 6 RJ45 Network Port
2 Audio In 7 USB 2.0
3 Audio Out 8 Accessories Out
4 HDMI Video Out 9 Power Input
5 VGA Video Out 10 Power Switch
Cameras connect to LAN1 (PoE gigabit network switch)
7
PRO1600X2
5432
9
1
8
76
10
1 Audio In 6 Accessories Out
2 BNC Camera Jacks 7 Power Input
3 Audio Out 8 Power Switch
4 HDMI Video Out 9 USB 2.0
5 RJ45 Network Port 10 VGA Video Out
Cameras connect to LAN1 (PoE gigabit network switch)
SYSTEM SETUP
QUICK START GUIDE ATTRIBUTES
This Quick Start Guide may refer to specic screens in the procedures. The Guide follows these
conventions:
• Italic text indicates a screen name, menu selection, etc. It is usually prefaced with "Select."
• BOLD text indicates an action, such as Save, Copy to, etc. It is usually prefaced with "Click."
• Many screens have several tabs on the screen. These tabs are referred to as Main Tabs, Side
Tabs, and Top Tabs. When referencing a specic screen progression, the text references Main
tabs/Side tabs/Top tabs in that order. For example, the illustration below would be referenced as
System Setting/Network Setting/Basic Setting.
SIDE TABS
MAIN TABS
TOP TABS
SAVE
8
INITIAL SETUP
1. Click the icon; select LOGIN. Enter admin (user name), skip password for now, and then
click Login.
2. Click the icon again; select GUIDE. Go through these screens to congure the system:
• Language setting: Default: ENGLISH; click Next.
• Display setting: Screen resolution default: 1280x1024-P60. Select 1920x1080-P60 if desired;
click Next.
• Network setting: Check Network Card dropdown list for Network Card. If you only have one LAN
port, do not set a static IP address and leave DHCP enabled. Click Next.
• Uniden ProSeries: QR codes display to download the Uniden ProSeries app. Apple QR code
downloads app for iOS version and Android QR code downloads the Android version.
3. Check the Next time no longer display box in lower left corner. This series of screens will not
display for further startups.
4. Click Finish.
SYSTEM SETUP CHECKLIST
Follow this checklist to turn up the XVR system. Refer to the ProSeries XVR Technical Installation
Manual for detailed procedures for these steps if needed.
INITIAL SYSTEM SETUP
_______
From Start/Guide, set:
• Default Language
• Display Resolution (Default - 1280 x 1024)
• LAN1 Network Settings
When nished, select Next time no longer display and click Finish.
_______
Go to System/Time Setting, Device Time tab and set:
• Device Time
• Date Format
• Time Zone
• Enable Daylight Savings Time and set start and end dates.
• Network Time Protocol (NTP) is enabled by default. Change to internal time source
if desired. Turn off if the customer does not want the recorder to go out on the
internet.
_______ The recording schedule default is for all cameras to record all the time (Channel
Setting/Schedule Setting/Recording Setting). Set up specic recording schedules.
_______ From System Setting/User Management, set up new users and change the Admin
password.
_______ From System Setting/Alarm Management/Alarm Input (or Alarm Output) top tab, set
up alarm inputs and outputs.
A limited power source must be used for alarm inputs.
_______ From System Setting/Network Parameter/Email Setting top tab, set up email
notication.
_______ From System Setting/Network Parameters/DDNS Setting top tab select Enable DDNS
to set up remote DDNS access.
_______ From Maintenance/System Information/Device Information top tab, update rmware if
desired. (The device will automatically reboot after upgrade.)
9
HARD DISK DRIVE (HDD) SETUP
_______ Go to Disk Manager/Storage Management and uncheck Missing Alarm for all non-
installed HDDs.
_______ From Disk Manager/Storage Management, verify HDD quantity and sizes. Shut down
and add HDDs if needed.
_______
Format any added hard drives before using. (RAID is not available on XVRs.)
NOTE: Pre-installed HDDs are factory-formaed and ready for use.
ADD IP CAMERAS
_______ Plan and set up IP addresses.
_______ Add IP cameras.
Change IP address of each camera to put it in the same range as the network
connector that the camera is connected to. Connect Success displays.
_______ Add Channels to Preview Groups
From Channel Setting/Channel Grouping, set up Preview Groups.
_______ From Channel Setting/Channel Grouping/Tour (right column), set up Tour Groups if
desired.
_______ Check and adjust camera images for focus and eld of view in Preview .
_______ From Preview, set up PTZ Presets, Cruise, and Pattern.
_______
Set individual camera settings for each channel if desired:
Other areas to set up include but are not limited to:
• Motion Detection (From Channel Setting/Channel Parameter/Motion top tab.
• Privacy Mask (From Channel Setting/Channel Parameter/Privacy Mask tab.
• Snapshot Parameters (From Channel Setting/Channel Parameter/Snapshot
Parameters tab.
• Video Tampering (From Channel Setting/Channel Parameter, Video Tampering
tab.
BATTERY
XVR systems have a CMOS clock button cell battery located on the PC board to maintain time
should power fail. Only Uniden service technicians should replace the battery (Chaochuang
Lithium Cell CR1220, 3V SC).
Battery Disposal Instructions: Check your local government website for battery
disposal guidelines. The correct procedure for disposing of different types of batteries
may vary signicantly by region. Check the website for your state, city, or municipality
for information on how to dispose of batteries in your area.
FCC Part 15/IC COMPLIANCE
FCC Compliance
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
Avis de conformité à la FCC : Ce dispositif a été testé et s’avère conforme à l’article 15 des
règlements de la Commission fédérale des communications (FCC). Ce dispositif est soumis
aux conditions suivantes: 1) Ce dispositif ne doit pas causer d’interférences nuisibles et; 2)
Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites pouvant nuire à son
10
fonctionnement.
Tout changement ou modication non approuvé expressément par la partie responsable pourrait
annuler le droit à l’utilisateur de faire fonctionner cet équipement.
IC Compliance
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Changes or modications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
Cet appareil est conforme aux normes RSS exemptes de licences d’Industrie Canada. Son
fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer
d’interférences nuisibles et (2), il doit pouvoir accepter les interférences, incluant celles pouvant
nuire à son fonctionnement normal.
Tout changement ou modication non approuvé expressément par la partie responsable pourrait
annuler le droit à l’utilisateur de faire fonctionner cet équipement.
THREE-YEAR LIMITED WARRANTY
Important: SAVE YOUR RECEIPT! Evidence of original purchase is required for warranty service.
WARRANTOR: Uniden America Corporation (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants,
for three years, to the original retail owner, this Uniden Product to be free from defects in materials &
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect 36
months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modied, altered, or used as part of any conversion kits,
subassemblies, or any congurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired
by someone other than an authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured
by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time
while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit &
return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred by
warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option,
may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING
TO THE PRODUCT & IS IN LIEU OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states
do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or
exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specic legal rights, & you may also have other rights which
vary from state to state. This warranty is void outside the United States of America & Canada.
11
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in
the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably
in its original packaging). The Product should include all parts & accessories originally packaged with the
Product. Include evidence of original purchase & a note describing the defect that has caused you to return
it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
C/O Saddle Creek
743 Henrietta Creek Rd., Suite 100
Roanoke, TX 76026
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Uniden PRO400X1 Guide de référence
- Taper
- Guide de référence
dans d''autres langues
- English: Uniden PRO400X1 Reference guide
Documents connexes
-
Uniden PRO800N2-5MP Guide de référence
-
-
-
-
-
-
-