Hilti SFE 2-A12 Mode d'emploi

SFE 2-A12

English 1

Français 16

Español 32

Português 48

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

1

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

2

3

4

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

SFE 2-A12

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 32

pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in this documentation and

on the product.

• Always keep the operating instructions with the product and make sure

that the operating instructions are with the product when it is given to

other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the

product. The following signal words are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal

injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious

injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to

slight personal injury or damage to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household

waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

2 English 2236949

*2236949*

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions

The numbering reflects the sequence of operations shown in the

illustrations and may deviate from the steps described in the text

Item reference numbers are used in the overview illustrations and

refer to the numbers used in the product overview section

This symbol is intended to draw special attention to certain points

when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Hilti Li-ion battery type series used. Observe the information given in

the section headed Intended use.

Lithiumion battery

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an

impact or is damaged in any other way.

Rated speed under no load

Direct current (DC)

Revolutions per minute

Drilling without hammer action

The product supports wireless data transmission compatible with

iOS and Android platforms.

1.4 Product information

products are designed for professional users and only trained,

authorized personnel are permitted to operate, service and maintain the

products. This personnel must be specifically informed about the possible

hazards. The product and its ancillary equipment can present hazards if

used incorrectly by untrained personnel or if used not in accordance with

the intended use.

The type designation and serial number are printed on the rating plate.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 3

▶ Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to inquire about the product.

Product information

Drill/driver SFE 2-A12

Generation: 01

Serial no.:

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here

complies with the applicable directives and standards. A copy of the

declaration issued by the certification department can be found at the end

of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916

Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶ Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

▶ Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

4 English 2236949

*2236949*

▶ Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk

of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal

injury.

▶ Use personal protective equipment. Always wear eye protection.

Protective equipment such as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate conditions will reduce

personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your finger on the switch

or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you

to become complacent and ignore tool safety principles. A careless

action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 5

▶ Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶ Disconnect the plug from the power source and/or remove the

battery pack, if detachable, from the power tool before making

any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool

accidentally.

▶ Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶ Maintain power tools and accessories. Check for misalignment or

binding of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and

the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and

grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A

charger that is suitable for one type of battery pack may create a risk of

fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use

of any other battery packs may create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small

metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a

fire.

▶ Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

▶

Do not use a battery pack or tool that is damaged or modified.

Damaged or modified batteries may exhibit unpredictable behaviour

resulting in fire, explosion or risk of injury.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

6 English 2236949

*2236949*

▶ Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to fire or temperature above 130° C (265 °F) may cause

explosion.

▶ Follow all charging instructions and do not charge the battery pack

or tool outside the temperature range specified in the instructions.

Charging improperly or at temperatures outside the specified range may

damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should

only be performed by the manufacturer or authorized service providers.

2.2 Drill safety warnings

Safety instructions for all operations

▶ Hold the power tool by insulated gripping surfaces, when performing

an operation where the cutting accessory or fasteners may contact

hidden wiring. Cutting accessory or fasteners contacting a "live" wire

may make exposed metal parts of the power tool "live" and could give

the operator an electric shock.

Safety instructions when using long drill bits

▶ Never operate at higher speed than the maximum speed rating of the

drill bit. At higher speeds, the bit is likely to bend if allowed to rotate

freely without contacting the workpiece, resulting in personal injury.

▶ Always start drilling at low speed and with the bit tip in contact with

the workpiece. At higher speeds, the bit is likely to bend if allowed to

rotate freely without contacting the workpiece, resulting in personal injury.

▶ Apply pressure only in direct line with the bit and do not apply

excessive pressure. Bits can bend causing breakage or loss of control,

resulting in personal injury.

2.3 Battery use and care

▶ Observe the special regulations and instructions applicable to the trans-

port, storage and use of Li-ion batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them

to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact,

have been dropped from a height or show signs of damage. In this case,

always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the

product in a non-flammable location, well away from flammable materials,

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 7

where it can be kept under observation and allowed to cool down. In this

case, always contact your Hilti Service.

2.4 Additional safety instructions

Personal safety

▶ Use the product only when it is in perfect working order.

▶ Never tamper with or modify the tool in any way.

▶ Do not look directly into the light source (LEDs) integrated in the drill/driver

and do not direct the light at other persons’ faces. This presents a risk of

dazzling or eye damage.

▶ Avoid touching rotating parts. Switch the power tool on only after bringing

it into position at the workpiece. Touching rotating parts, especially

rotating accessory tools, may lead to injury.

▶ Wear protective gloves also when changing the accessory tool. Touching

the accessory tool presents a risk of injury (cuts or burns).

▶ Always hold the tool securely by the grip. If the accessory tool (e.g. the

drill bit) sticks and stalls, the power tool, due to its high torque, may

tend to rotate about its own axis in the direction opposite to that of the

accessory tool.

▶ Make sure that the workplace is well ventilated and, where necessary,

wear a respirator appropriate for the type of dust generated. Contact with

or inhalation of the dust may cause allergic reactions and/or respiratory

or other diseases to the operator or bystanders. Certain kinds of dust

are classified as carcinogenic such as oak and beech dust, especially

in conjunction with additives for wood conditioning (chromate, wood

preservative). Material containing asbestos may be handled only by

specialists.

▶ Take breaks and exercise your fingers to improve the blood circulation.

Exposure to vibration during long periods of work can lead to disorders

of the blood vessels and nervous system in the fingers, hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric

cables or gas and water pipes. External metal parts of the power tool may

give you an electric shock if you damage an electric cable accidentally.

Power tool use and care

▶ Secure the workpiece. Use clamps or a vice to hold the workpiece in

position. The workpiece is thus held more securely than by hand and both

hands remain free to operate the power tool.

▶ Immediately switch off the power tool if the accessory tool jams. The

power tool might twist off-line.

▶ Wait until the power tool stops completely before you lay it down.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

8 English 2236949

*2236949*

3 Description

3.1 Product overview 1

@

1/4" hex socket

;

Torque and drilling mode se-

lector ring

=

Gear speed selection switch

%

Forward/reverse selector

switch with safety lock

&

Grip

(

Fitting slot for accessories

(fig.: Belt hook)

)

Lamp

+

Charge status display

§

Battery release button

/

Control switch (with electronic

speed control)

:

Adapter

3.2 Intended use

The product described is a hand-held cordless drill / driver for driving and

removing screws, drilling in metal, wood and plastic. The product has an

interchangeable chuck and can be fitted with various adapters.

• Use only Hilti Li-ion batteries of the B 12 series with this product.

• Use only Hilti-approved battery chargers to charge these batteries. More

information is available from your Hilti Store or from: www.hilti.group

3.3 Items supplied

Drill / driver, operating instructions

Other system products approved for use with this product can be found

at your local Hilti Store or online at: www.hilti.group

3.4 Charge status display

The charge status of the Liion battery is displayed after pressing the release

button.

Status Meaning

4 LEDs light up. Charge status: 75 % to 100 %

3 LEDs light up. Charge status: 50 % to 75 %

2 LEDs light up. Charge status: 25 % to 50 %

1 LED lights up. Charge status: 10 % to 25 %

1 LED flashes, the power tool is in

working order.

Charge status: < 10 %

Battery charge status cannot be displayed while the control switch is

pressed.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 9

3.5 Overload and overheating protection

The power tool is equipped with an electronic system to protect against

overloading and overheating. The power tool switches itself off automatically

in the event of overloading or overheating. After releasing the control switch,

the power tool may not restart immediately when the switch is pressed again

(while the power tool is cooling down).

Overloading or overheating are not indicated by the charge status

display.

3.6 Adapter

This product has different adapters for various applications.

The following adapters are available:

Adapter Description

Hex bit holder for bits with mechanical clamping mechanism.

Keyless chuck for sizes in the range:

1.5 mm … 13 mm

(0.06 in … 0.5 in)

Right-angle adapter for working in cramped conditions, with

magnetic hex bit holder.

Combinable with other adapters.

Eccentric adapter for working close to the wall, with magnetic

hex bit holder.

4 Technical data

4.1 SFE 2-A12

Rated voltage

10.8 V

Weight

1.1 kg

(2.4 lb)

Maximum speed 1st gear

400 /min

2nd gear

1,600 /min

Maximum torque

Screwdriving

0.5 Nm … 5 Nm

(0.4 ftlb

f

… 4 ftlb

f

)

Drilling

≤ 25 Nm

(≤ 18 ftlb

f

)

Drill-bit diameter Softwood

1.5 mm … 13 mm

(0.06 in … 0.5 in)

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

10 English 2236949

*2236949*

Drill-bit diameter Hardwood

1.5 mm … 10 mm

(0.06 in … 0.4 in)

Metal

1.5 mm … 6 mm

(0.06 in … 0.2 in)

4.2 Battery

Battery operating voltage

10.8 V

Ambient temperature for operation

−17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature

−20 ℃ … 40 ℃

(−4 ℉ … 104 ℉)

Battery charging starting temperature

4 ℃ … 40 ℃

(39 ℉ … 104 ℉)

5 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or

before changing accessories.

Observe the safety instructions and warnings in this documentation and on

the product.

5.1 Charging the battery

1. Before charging the battery, read the operating instructions for the

charger.

2. Make sure that the contacts on the battery and the contacts on the

charger are clean and dry.

3. Use an approved charger to charge the battery.

5.2 Inserting the battery

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery

and the contacts on the product are free of foreign matter.

▶ Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the battery holder until it engages with an audible

click.

3. Check that the battery is seated securely.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 11

5.3 Removing the battery

1. Press the battery release buttons.

2. Remove the battery from the tool.

5.4 Fitting the adapter

Other adapters can be fitted additionally onto the right-angle adapter.

1. Insert the adapter into the chuck.

➥ The adapter snaps into engagement.

2. Check correct installation.

5.5 Removing the adapter 4

1. Pull the locking sleeve and hold it in this position.

2. Remove the adapter.

5.6 Inserting bits (hex bit holders)

The hex bit holders of the eccentric adapter and the right-angle adapter

hold the bit magnetically.

1. Pull the locking sleeve and hold it in this position.

2. Insert the bit.

3. Release the locking sleeve.

5.7 Inserting drill bit (keyless chuck)

1. Open the keyless chuck.

2. Insert the drill bit.

3. Close the keyless chuck.

6 Operation

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery

and the contacts on the product are free of foreign matter.

▶ Make sure that the battery always engages correctly.

Observe the safety instructions and warnings in this documentation and on

the product.

6.1 Selecting the gear 3

▶ Operate the gear selector switch.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

12 English 2236949

*2236949*

6.2 Setting the torque

The torque is limited only when the power tool is set to screwdriving

mode .

▶ Turn the adjusting ring to the desired torque setting.

6.3 Switching between forward (clockwise) and reverse rotation

(counter-clockwise) 2

An interlock prevents switching while the motor is running. The control

switch is locked when the forward/reverse switch is in the middle

position (safety lock).

1. Operate the forward/reverse switch.

➥ The switch-on safety lock is active.

2. Operate the forward/reverse switch.

➥ The direction of rotation is set as desired.

6.4 Switching on and off

1. Press the control switch.

➥ The power tool starts.

Speed can be controlled steplessly right up to maximum by varying

how far the control switch is pressed in.

2. Release the control switch.

➥ The power tool switches off.

6.5 Screwdriving

1. Set the torque. → page 12

2. Set the direction of rotation to forward (clockwise) or reverse (counter-

clockwise). → page 12

3. Press the control switch. → page 12

6.6 Drilling

1.

Set the torque setting ring to the symbol.

2. Set the direction of rotation to forward (clockwise). → page 12

3. Press the control switch. → page 12

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 13

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance

tasks!

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning

agents containing silicone as these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals

and make sure that they all function correctly.

• Do not operate the product if signs of damage are found or if parts

malfunction. Have it repaired immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and

check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by Hilti for use with the product can be found at your local

Hilti Store or online at: www.hilti.group.

8 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of

transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

14 English 2236949

*2236949*

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a

window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by

children or unauthorized persons.

▶ Check the tool and batteries for damage before use after long periods of

storage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable

to remedy the problem by yourself, please contact Hilti Service.

9.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

The power tool does

not work.

The battery is not fully

inserted.

▶ Insert the battery.

Low battery. ▶ Charge the battery.

The on/off button

cannot be pressed,

i.e. the button is

locked.

The forward/reverse

selector switch is in the

middle position.

▶ Set the

forward/reverse

switch to the desired

position.

The battery runs

down more quickly

than usual.

Very low ambient tem-

perature.

▶ Allow the battery to

warm up slowly to

room temperature.

The battery doesn’t

engage with an audi-

ble click.

The retaining lugs on the

battery are dirty.

▶ Clean the retaining

lugs and push the

battery in until it

engages. Contact

Hilti Service if the

problem persists.

The tool or battery

gets very hot.

The tool is overloaded

(application limits ex-

ceeded).

▶ Pay attention to the

power and perfor-

mance rating of the

product before using

it, i.e check its suitabil-

ity for the job on hand.

See the “Technical

data” section.

10 Disposal

Most of the materials from which Hilti tools and appliances are manu-

factured can be recycled. The materials must be correctly separated before

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

*2236949*

2236949 English 15

they can be recycled. In many countries, your old tools, machines or appli-

ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti

representative for further information.

▶ Do not dispose of power tools, electronic equipment or batteries as

household waste!

11 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about

the warranty conditions.

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

16 Français 2236949

*2236949*

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service.

C'est la condition préalablement requise pour assurer la sécurité du travail

et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la

présente documentation ainsi que celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement

le transmettre à des tiers avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du

produit. Les termes de signalisation suivants sont utilisés :

DANGER

DANGER !

▶ Pour un danger imminent qui peut entraîner de graves blessures corpo-

relles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶ Pour un danger potentiel qui peut entraîner de graves blessures corpo-

relles ou la mort.

ATTENTION

ATTENTION !

▶ Pour attirer l'attention sur une situation pouvant présenter des dangers

entraînant des blessures corporelles légères ou des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures

ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Printed: 07.08.2019 | Doc-Nr: PUB / 5507951 / 000 / 00

La page charge ...

Hilti SFE 2-A12 Mode d'emploi

Hilti SFE 2-A12 Mode d'emploi

dans d''autres langues

Documents connexes