Miele C3 Alize Manuel utilisateur

en Operating Instructions Vacuum Cleaner

fr Instructions d'utilisation Aspirateur

es Manual de Uso y Manejo Aspiradora

SGDE0, SGEE0, SGFE0, SGJE0

M.-Nr. 10 093 350

HS15

2

Only Miele FilterBags, filters and accessories with

the "Original Miele" logo can be used with this

vacuum. Only then can the suction power of the

vacuum cleaner reach its optimum potential creating

the best possible cleaning results.

USE OF NON-MIELE COMPONENTS MAY VOID

THE WARRANTY.

,

The use of FilterBags made of paper or a similar

material, or FilterBags with a cardboard retaining

plate can lead to serious damage to the vacuum

cleaner and may void the warranty, just as with the

use of FilterBags without the "Original Miele" logo.

The "Original Miele" Logo will appear on the

packaging or directly on the FilterBag.

Purchasing new FilterBags and filters

Original Miele FilterBags and filters can be purchased

from an authorized Miele vacuum dealer or by visiting the

Miele store at www.mieleusa.com.

IMPORTANT SAFETY INSTRUCTIONS

Guide to the vacuum cleaner

Before using the vacuum cleaner

Using the included accessories

Use

Power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Turning the vacuum cleaner on and off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Selecting the suction power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Opening the auxiliary air regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

While vacuuming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Illuminating the work area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Parking, transport and storage

Maintenance and care

Purchasing new filter bags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Which filter bags and filters are the right ones? . . . . . . . . . . . . . . . . . . . . . . . . . . 16

When to change the filter bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

How to change the filter bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

When should I change the dust compartment filter?. . . . . . . . . . . . . . . . . . . . . . . 17

How to change the dust compartment filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

When should I change the exhaust filter? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

How to replace the AirClean exhaust filter?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

How do I change the Active AirClean 50 or the HEPA AirClean 50 exhaust filter? 18

Exchanging exhaust filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Service indicator with reset button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Changing the batteries on the LED handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

When to change the thread catcher of the standard floor brush . . . . . . . . . . . . . 19

Replacing the thread catchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Cleaning and care

Frequently asked questions

Technical service

Optional accessories

Caring for the environment

LIMITED WARRANTY - VACUUM CLEANERS USA

3

en - Contents

When using an electrical appliance, basic precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS APPLIANCE

Keep these operating instructions in a safe place and pass them on to any

future user.

WARNING-

To reduce the risk of fire, electric

shock or injury:

Before using

~

Check the voltage rating of the

vacuum cleaner before connecting the

power cord to an electrical outlet. Your

power source should correspond with

the voltage rating plate located on the

underside of the vacuum. Use only

household AC outlets. Never use DC

power sources. If you are not sure of

your home’s voltage supply, consult a

qualified electrician. Connecting the

vacuum cleaner to a higher voltage

than indicated in these instructions may

result in damage to the vacuum cleaner

or injury.

~

To reduce the risk of electric shock,

this appliance has a polarized plug

(one blade is wider than the other.) This

plug will fit in a polarized outlet only one

way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to

install the proper outlet. Do not alter the

plug in any way.

~

A damaged vacuum cleaner can be

dangerous. Check the packaging,

vacuum cleaner and accessories for

any signs of damage. Do not use a

damaged appliance.

~

Do not use with a damaged cord or

plug. If the appliance is not working as

it should, has been dropped, damaged,

left outdoors or submerged in water,

bring it to a service center.

~

The electrical outlet must be fitted

with a 15 A fuse.

en - IMPORTANT SAFETY INSTRUCTIONS

4

Use

~

Do not use on people or animals.

~

Do not use outdoors or on wet

surfaces. Only dry surfaces should be

vacuumed.

~

Use only as described in this

manual. Use only Miele recommended

accessories.

~

Do not alter or modify the vacuum

cleaner.

~

This appliance is intended for

household use only.

~

Do not allow the vacuum cleaner to

be used as a toy. Close attention is

necessary when used near children.

~

Keep batteries out of the reach of

children.

~

Important information on the

handling of batteries:

- Do not short circuit or recharge

batteries, or throw them into a fire.

- Disposing of batteries: Remove the

batteries from the LED handle and

dispose of them in your recycling bin.

Do not dispose of them with the normal

household waste.

~

Never use the vacuum cleaner

without the filter bag or filters in place.

Otherwise it could be damaged.

~

If a filter bag is not inserted, the dust

compartment lid will not close. Do not

force it shut.

~

Do not leave the vacuum plugged

in. Unplug it from the outlet when not in

use and before servicing.

~

On the underside of the vacuum

handpiece is a metal insert designed to

absorb static electricity. Please make

certain that your hand remains around

this metal insert when vacuuming.

~

Persons which lack physical,

sensory or mental abilities or

experience with the machine should not

use it without supervision or instruction

by a responsible person.

~

Unwind the cord completely to aid

the vacuum cleaner in dissipating heat.

~

This vacuum should not be used to

entrap or retain any hazardous

materials.

~

Do not use the vacuum cleaner to

pick up liquids or damp dirt. This could

impair the electrical safety of the

vacuum cleaner. Wait for freshly

shampooed carpets to dry.

~

Do not vacuum anything that is

burning or smoking such as cigarettes,

matches or hot ashes. The vacuum

cleaner could catch fire.

~

Do not vacuum toner dust. Toner,

such as that used in printers and

photocopiers can conduct electricity.

~

Do not use to pick up any flammable

or combustible liquids, such as

gasoline, or use in areas where they

may be present. The vacuum cleaner

could explode.

~

Do not vacuum up items which are

heavy, hard or have sharp edges. They

could cause a blockage and damage

the appliance.

en - IMPORTANT SAFETY INSTRUCTIONS

5

~

Do not pull or carry by the cord, use

the cord as a handle, close a door on

the cord, or pull the cord around sharp

edges or corners. Do not run the

appliance over the cord. Keep the cord

away from heated surfaces.

~

Do not unplug by pulling on the

cord. To unplug, grasp the plug, not the

cord.

~

Do not handle the plug or vacuum

with wet hands.

~

Keep the power cord, hair, loose

clothing, fingers and all parts of the

body away from openings and moving

parts.

~

Do not place anything into the

openings of the vacuum cleaner. Do

not use if any openings are blocked;

keep them free of dust, lint, hair, or

anything that may reduce air flow.

~

This appliance is equipped with a

power cord reel. Hold plug when

rewinding onto cord reel. Do not allow

plug to whip when rewinding.

~

Turn off all controls before

unplugging.

~

Use extra care when cleaning on

stairs.

~

Floor attachments, accessories and

wands must not be used at head level

to avoid injury to eyes and ears.

~

Monitor the filter bag change

indicator and inspect all filters regularly.

For best performance, the filter bag

and filters should be replaced when

necessary. A full bag or blocked filter

will reduce the vacuum cleaner’s

suction power. A temperature limiter

automatically switches the vacuum

cleaner off if it gets too hot, see

"Frequently asked questions".

Using accessories

~

The hose and the telescopic wand

contain electrical wires. Do not use the

vacuum cleaner if these parts are

damaged, cut or punctured. Avoid

picking up sharp objects. Danger of

electric shock!

~

Unplug the vacuum when changing

accessories, especially the Hose,

Telescopic wand, Turbobrush and

Powerbrush.

~

To avoid the risk of injury when

vacuuming with a Miele Power or

Turbobrush do not touch the rotating

roller brush. Danger of injury.

~

The socket on the vacuum cleaner

(depending on model) must only be

used for the Miele Powerbrush

specified for use with this appliance.

~

Danger of injury. The Miele

Powerbrush is a motor driven

accessory for use only with Miele

vacuum cleaners. The vacuum cleaner

must not be used with another

manufacturer’s powerbrush.

en - IMPORTANT SAFETY INSTRUCTIONS

6

~

Do not use the vacuum cleaner

without an accessory attached. The rim

could be damaged and injuries could

result from sharp edges.

~

Miele filter bags are disposable and

intended to be used only once. Do not

attempt to reuse. An over stuffed filter

bag will reduce the efficiency of the

vacuum cleaner.

~

Only use genuine Miele filter bags

with the Miele quality signet and

original Miele filters and accessories.

Only then will the manufacturer

guarantee its safety.

Cleaning, maintenance and

repairs

~

Turn the vacuum cleaner off after

each use and before every cleaning /

maintenance. Pull the plug from the

outlet.

~

Never submerge the vacuum

cleaner in water. Clean only with a dry

cloth or slightly damp cloth when

disconnected from the mains supply. If

moisture gets into the appliance there

is a risk of electric shock.

~

The electro-suction hose and the

telescopic wand contain electrical

wires. The plug connectors must not

come in contact with water. These

items may only be cleaned with a dry

cloth, no moisture can touch them.

Danger of electric shock.

~

Repairs must only be performed by

an authorized service agent in

accordance with national and local

safety regulations. Unauthorized repairs

could cause injury or machine damage.

~

If the power cord is damaged it

should be replaced along with a new

cable reel by Miele Technical Service.

Disposing of an old appliance

~

Before discarding an old vacuum

cleaner, please cut off the power cord

and render the plug useless. Ensure

the appliance presents no danger to

children while being stored for

disposal.

SAVE THESE

INSTRUCTIONS

en - IMPORTANT SAFETY INSTRUCTIONS

7

en - Guide to the vacuum cleaner

8

The illustrations show the vacuum cleaner and all available options.

a Suction hose *

b Accessory compartment lid release

c Airflow indicator

d Display panel *

e Foot switch for automatic cord rewind

f Park-System for breaks in vacuuming

g Foot switch On/Off s

h Power cord

i Swivel casters *

j Exhaust filter *

k Park-System for storage (on both sides of the vacuum cleaner,

illuminated depending on model)

l Dust compartment filter (motor protection)

m Bracket cover for the Powerbrush outlet

n Original Miele filter bag

o Carrying handle

p Floor tool *

q Lock release button

r Telescopic wand *

s Dust compartment lid release

t Telescopic wand release button

u Powerbrush outlet *

v Elbow *

w LED *

x Standby button for brief breaks in vacuuming *

y Suction power buttons + / -*

z Handpiece (depending on model with auxiliary air regulator) *

{ Thermo indicator light § *

| Reset button *

} Standby indicator *

~ Service indicator with reset button *

The features marked * may vary or not be available on your model.

en - Guide to the vacuum cleaner

9

The illustrations referred to in the text

are shown on the fold-out pages at the

end of these operating instructions.

Before using the vacuum

cleaner

Attaching the suction hose (see fig. 1)

^

Insert the elbow into the suction

socket until it clicks into place.

Disconnecting the hose (see fig. 2)

^ Press the release buttons on the

sides of the elbow and lift the hose

from the socket.

Connecting the suction hose and

handpiece (see fig. 3)

Depending on the model, the hand-

piece is already pre-fitted at the other

end of the hose at the factory. If the

handpiece of your model is separate, it

just needs to be connected to the hose.

^

Insert the hose into the handpiece

until it clicks into place.

Connecting the telescopic wand and

handpiece (see fig. 4)

^

Insert the handpiece into the

telescopic wand until it clicks into

place. Use the inlet guides of both

parts to direct insertion.

^

To separate the parts from each

other, press the wand release button

and pull the handpiece away from

the telescopic wand with a slight

rotation.

Adjusting the telescopic wand (see

fig. 5)

This telescopic wand is composed of

two interlocking tube sections that can

be adjusted to the desired length.

^

Press the adjustment button and

slide the tubes to the desired length.

Attaching the standard floor brush

AllTeQ or AirTeQ (see fig. 6)

(depending on model)

Observe the cleaning instructions of

the floor manufacturer.

^ Place the floor brush on the

telescopic wand and twist back and

forth until it clicks into place.

^ To remove the floor brush from the

telescopic wand, press the release

button.

The floor brush is intended for everyday

use on carpets, rugs, and hard flooring

that is not susceptible to scratching.

For other floor coverings, we recom

-

mend using the special Miele brushes

(see the section on "Optional accesso

-

ries").

Adjusting the standard floor brush

AllTeQ or AirTeQ (see fig.7+8)

(depending on model)

Observe the cleaning instructions of

the floor manufacturer.

To clean carpets and rugs, lower the

bristles by

^

pressing the foot switch %.

en

10

To clean hard flooring, raise the tool by

^

pressing the foot switch ).

Always use the floor brush with the

bristles raised to clean floors with

very deep joints or gaps.

AirTeQ floor brush (see fig. 8)

This floor brush is specially designed to

achieve good cleaning results with low

energy consumption. It is especially

aerodynamic and powerful.

,

If the floor tool is difficult to move

across the carpeting reduce the

suction power.

Activating the exhaust filter change

indicator

Depending on the model, one of the

following standard exhaust filters is

installed (see fig. 9).

a AirClean Filter

b Active AirClean 50 Filter (black)

c HEPA AirClean 50 Filter (white)

If your vacuum cleaner is equipped

with a type b or c exhaust filter, you will

need to activate the exhaust filter

change indicator.

^

Open the dust compartment lid and

raise until it clicks into place (see fig.

10).

^

Remove the marker strip (see fig. 11).

^

Press the exhaust filter change

indicator ~ (see fig. 12).

^

After about 10-15 seconds, a small

red marker will appear in the

left-hand side of the display (see fig.

13).

^

Close the dust compartment lid until

it clicks into place. Take care not to

catch the dustbag in the lid.

How the exhaust filter change indica

-

tor works

The exhaust filter change indicator

displays the usable life of the exhaust

filter. The indicator will turn fully red

after approx. 50 hours of operation,

which is equivalent to one year of

average use (see fig. 14).

Inserting batteries into the LED

handle (see fig. 15 + 16)

(depending on model)

a Loosen the screws on the cover.

b Press down on both sides of the

cover to remove.

c Take out the battery holder and insert

the three batteries supplied making

sure they are inserted correctly.

d Replace the batter holder in the

direction of the arrows on the holder

and battery compartment, so that

both line up.

e Replace the cover and tighten the

screws.

en

11

Using the included accessories

(see fig. 17)

The following accessories are included:

a Crevice nozzle

For cleaning in folds, crevices and

corners.

b Dust brush with natural bristles

For cleaning moldings, ornate,

carved or especially sensitive items.

The brush head can be swiveled to

the optimal cleaning position.

c Upholstery tool

For cleaning upholstery, mattresses,

cushions, curtains, covers, etc.

Certain models come with one of the

following accessories that are not

shown.

– Powerbrush

– Turbobrush

– Comfort handle with light

These vacuum cleaners have separate

operating instructions for the

corresponding accessory.

Removing the accessories (see fig. 18)

^

Press the release button.

The accessory compartment opens.

^

Take out the accessory needed.

^

Close the accessory compartment by

pressing on the lid.

Standard floor brush AllTeQ or Air

-

TeQ (see fig. 19)

(depending on model)

Also suitable for vacuuming stairs.

,

For your own safety, always

vacuum stairs from bottom to top.

Use

Power cord

,

Unwind the cord completely to

aid the vacuum in dissipating heat.

Do not pull or carry by the cord, use

the cord as a handle, close a door on

the cord, or pull the cord around

sharp edges or corners. Do not run

the appliance over the cord. Keep

the cord away from heated surfaces.

Do not unplug by pulling the cord. To

unplug grasp the plug, not the cord.

This appliance is equipped with a

power cord reel. Hold the plug when

rewinding onto cord reel. Do not

allow plug to whip when rewinding.

Unwinding (see fig. 20)

^

Pull the cord out to the desired length

(max. approx. 24.6 ft. / 7.5 m).

^

Insert the plug into the electrical

outlet.

Depending on model, the lighting of the

Park-System on both sides of the

vacuum cleaner switches on.

The first time the vacuum cleaner is

used, the lighting turns on after

approx. two minutes.

en

12

,

If you intend to use the vacuum

cleaner for more than 30 minutes,

you will need to pull the cord all the

way out. This is to help prevent

overheating and damage to the

appliance.

Rewinding (see fig. 21)

^

Unplug the power plug from the

electrical outlet.

If your vacuum cleaner is equipped

with an illuminated Park-System, the

lighting switches off again automatically

approx. 30 seconds after disconnecting

the power.

^ Press the rewind foot switch and the

power cord will automatically rewind.

Turning the vacuum cleaner on and

off (see fig. 22)

^ Press the On/Off foot switch s.

Selecting the suction power

You can adjust the suction power to suit

the situation. When you reduce the

suction power, the floor brush can be

moved with less effort.

On the vacuum cleaner you will see

various symbols showing examples of

which power level is recommended for

which purpose.

The selected power level light is yellow.

#- Draperies, fabrics

$- Upholstery, pillows

%- Thick pile carpets, rugs and

runners.

Auto = Automatic adjustment of the

suction power to the flooring

(depending on model)

,

Do NOT use the "Auto" power

level to vacuum draperies or other

lightweight fabrics. Excessive

suction may cause damage to such

items.

*- Energy-efficient everyday

vacuuming, low noise

(- Low pile carpets

)- Hard flooring and intensive

cleaning of carpets.

,

If the floor tool is difficult to move

across the carpeting reduce the

suction power.

Depending on the model, your vacuum

cleaner will be equipped with one of the

following suction settings.

Foot switches (see fig. 23)

When used for the first time, the

vacuum cleaner will turn itself on to the

highest power level.

The next time it is used, it will turn on to

the power level last selected.

^

To select a higher power setting,

press the + foot switch.

^

To select a lower power setting,

press the - foot switch.

13

en

Automatic foot switches (see fig. 24 +

25)

When used for the first time, the

vacuum cleaner turns on to the "Auto"

power level.

Auto = Automatic adjustment of the

suction power to the flooring

,

Do NOT use the "Auto" power

level to vacuum draperies or other

lightweight fabrics. Excessive

suction may cause damage to such

items.

^ To select a higher power setting,

press the + foot switch.

^ To select a lower power setting,

press the - foot switch.

The next time it is used, it turns on to

the power level last selected.

Opening the auxiliary air regulator

(see fig. 26)

(depending on model)

You can easily reduce the suction

power briefly to prevent the brush from

sticking to textile flooring, for example.

^

Open the auxiliary air regulator just

far enough so that the suction nozzle

moves easily.

This reduces the suction so the floor

tool is easier to push.

While vacuuming (see fig. 27 + 28)

The vacuum cleaner can also stand on

its end for vacuuming stairs, drapes

etc.

,

To prevent static electricity your

hand must touch the metal inlay on

the underside of the vacuum hand

-

piece. Be certain to continuously

touch this inlay when vacuuming

fine dust, flour or sawdust as these

materials are more likely to create a

static electricity. To further prevent

static discharge while vacuuming,

pull the vacuum along by the hose

with one hand while continuing to

hold the handpiece in the other

hand.

Illuminating the work area (see fig. 29)

(depending on model)

Your vacuum cleaner is equipped with

an LED on the handle to illuminate the

work area.

^ Press the I button on the LED

handle.

It will turn itself off automatically after

approx. 30 seconds.

Parking, transport and storage

Park-System (see fig. 30)

(not for use with Powerbrushes

SEB 228 / EB03 and SEB 236 / EB01)

The Park-System allows you to park the

telescopic wand and the suction unit on

the vacuum cleaner during brief pauses.

^

Insert the parking clip attachment on

the suction unit into the parking slot

from above.

If the vacuum is on an incline, e.g. a

ramp, slide the tube sections of the

telescopic wand all the way in.

en

14

Turning on and off with the

Park-System

(depending on model)

The vacuum cleaner is automatically

turned off if you insert the suction unit

with the parking slot into the

Park-System.

Lifting the suction unit out turns the

vacuum cleaner automatically back on

using the last selected power level.

Park-System for storage (see fig. 31)

,

Turn the vacuum cleaner off

after use. Unplug the power plug

from the electrical outlet.

After approx. 30 seconds the parking

system lighting turns off if your vacuum

cleaner is equipped with an illuminated

Park-System.

^ Stand the vacuum cleaner upright.

It is helpful to completely insert the

tubes into the telescopic wand.

^

Insert the suction unit with the

parking slot from above into either

side of the Park-System (cannot be

used with Powerbrushes SEB 228 /

EB03 and SEB 236 / EB01).

This makes the vacuum cleaner easier

to carry and store.

Maintenance and care

,

Turn off and unplug the vacuum

cleaner before performing any

maintenance work.

The Miele filter system consists of the

following three components.

–

Filter bag

–

Exhaust filter

–

Dust compartment filter

Each of these components must be

changed periodically to maintain the

vacuum cleaner’s efficiency.

Only use Miele filter bags, filters and

accessories with the "Original Miele"

logo. Only then can the suction

power of the vacuum cleaner reach

its optimum potential for the best

possible cleaning results.

,

The use of filter bags made of

paper or a similar material, or filter

bags with a cardboard retaining

plate can lead to serious damage to

the vacuum cleaner and may

possibly voiding the warranty, just

as with the use of filter bags without

the "Original Miele" logo.

Purchasing new filter bags and filters

Original Miele filter bags and filters can

be purchased from an authorized Miele

vacuum dealer or by visiting the Miele

store at http://store.miele.com.

en

15

Which filter bags and filters are the

right ones?

This vacuum cleaner uses Original

Miele filter bags Type G/N and Original

Miele filters, the "Original Miele" Logo

will appear on the packaging or directly

on the filter bag.

An "AirClean" exhaust filter and a dust

compartment filter are supplied with

every box of Miele filter bags.

If you would like to purchase additional

Miele filters separately, contact your

vacuum cleaner dealer or Miele, please

quote the model number of your Miele

vacuum cleaner to ensure correct parts

are ordered. These parts are also

available to order from the online Miele

store.

The exhaust filter supplied with the

vacuum cleaner can be exchanged

with another type of Original Miele filter

(see "Exchanging exhaust filters").

When to change the filter bag (see

fig. 32)

Change the filter bag when the colored

marker in the airflow indicator

completely fills the display in red.

Filter bags are disposable and are

designed to be used only once.

Dispose of full filter bags. Do not

attempt to reuse.

Clogged pores reduce the suction

power of the vacuum cleaner.

Check the airflow indicator

^

Attach the standard floor brush

AllTeQ or AirTeQ (depending on mo

-

del) to the vacuum cleaner. All other

suction tools may affect the function

of the airflow indicator.

^ Switch the vacuum cleaner on and

select the highest power level.

^ Lift the floor brush slightly off the

floor. If the marker completely fills the

indicator window, the filter bag needs

to be changed.

How the airflow indicator works

The airflow indicator is designed to

show when the bag is full of common

household dust and measures the

amount of air flow through the filter bag.

Normal household dust is a mixture of

dust, hair, carpet fluff, threads, sand,

etc.

However, if fine dust, such as drill dust,

sand, plaster or flour is vacuumed, the

pores of the filter bag may become

blocked. The marker will indicate that

the bag is "full" even when it is not. The

filter bag should be changed as the

suction power is greatly reduced.

en

16

If the bag is bulging with pet fur, hair,

carpet fluff, etc. the indicator may not

register "full". This is because the air

flow of the filter bag may still be high

enough not to activate the marker to

show maximum. The filter bag should

still be changed.

How to change the filter bag (see fig.

33 + 34)

^

Lift the release button and open the

dust compartment lid upwards until it

clicks into place (see fig. 10).

The filter bag has a flap that

automatically closes to prevent dust

from escaping when the bag is

removed.

^ Grasp the collar and remove the filter

bag from the holder.

^ Insert the new filter bag into the blue

holder as far as it will go. Note: Do

NOT unfold the filter bag when you

take it out of the box.

^

Unfold the filter bag in the dust

compartment when possible.

^

Now close the dust compartment lid

until it clicks into place, take care not

to catch the filter bag in the lid.

,

If you do not insert a replacement

filter bag, the dust compartment lid is

designed not to close. Do not use

force!

When should I change the dust

compartment filter?

Change the filter each time you open a

new box of genuine Miele filter bags. A

dust compartment filter is supplied with

every box of Miele filter bags.

How to change the dust

compartment filter (see fig. 35)

^

Open the dust compartment lid.

^

Grasp the finger grip and pull the

filter bag out of the holder.

^

Open the blue filter frame until it

clicks into place, use the clean

corner to remove the used dust

compartment filter.

^ Insert a new dust compartment filter.

^ Close the filter frame.

^ Insert the new filter bag into the blue

holder as far as it will go.

^ Close the dust compartment lid until

it clicks into place.

When should I change the exhaust

filter?

Depending on the model, your vacuum

cleaner will use one of the following

standard exhaust filters (see fig. 9):

a AirClean Filter

Change the exhaust filter each time you

open a new box of Miele filter bags.

A new AirClean exhaust filter is included

in every box of Miele filter bags.

en

17

b Active AirClean 50 Filter (black)

c HEPA AirClean 50 Filter (white)

If the display of the exhaust filter

change indicator has turned fully red

(see fig. 14).

The indicator light will come on after

approx. 50 hours of operation, which is

equivalent to one year of average use.

The vacuum cleaner can still be used

however, the filter performance and

suction power will be reduced.

How to replace the AirClean exhaust

filter? (see fig. 36 + 37)

Make sure that only one exhaust

filter is inserted in the frame.

^ Open the dust compartment lid.

^ Squeeze the release for the filter

frame and open until it clicks.

^ Grasp one of the two clean corners

(see arrow) to remove the used

AirClean exhaust filter.

^

Insert a new AirClean exhaust filter.

But if you want to install an Active

AirClean 50 filter or HEPA AirClean 50

filter, you must heed the section

"Maintenance and care -

Exchanging exhaust filters".

^

Close the filter frame.

^

Close the dust compartment lid until

it clicks into place.

How do I change the Active AirClean

50 or the HEPA AirClean 50 exhaust

filter? (see fig. 38 + 39)

Make sure that only one exhaust

filter is inserted in the frame.

^

Open the dust compartment lid.

^

Lift the exhaust filter and remove it.

^

Install the new Active AirClean 50 or

HEPA AirClean 50 exhaust filter and

press it downwards.

^

Press the exhaust filter change

indicator ~ (see fig. 12).

^ After about 10-15 seconds, a small

red marker will appear in the left-hand

side of the display (see fig. 13).

If you want to install an AirClean

exhaust filter, you must adhere to

the section "Maintenance and

care - Exchanging exhaust filters".

^

Close the dust compartment lid until

it clicks into place.

Exchanging exhaust filters

Depending on the model, your vacuum

cleaner will use one of the following

standard exhaust filters (see fig. 9):

a AirClean Filter

b Active AirClean 50 Filter (black)

c HEPA AirClean 50 Filter (white)

en

18

Important

Make sure that only one exhaust

filter is inserted in the frame.

1. If you replace exhaust filter a with

exhaust filter b or c, you must be sure

to remove the filter frame before

inserting the new filter type. The

exhaust filter change indicator must

also be activated (see fig. 12).

2. If you replace exhaust filter b or c

with exhaust filter a, you must be sure

to place the new filter in the filter frame

* (see fig. 37).

* Filter frame - see section on "Optional

accessories"

Service indicator with reset button

(see fig. 40)

(depending on model)

The indicator light will come on after

approx. 50 hours of operation, which is

equivalent to one year of average use.

Check if the motor protection filter and

the exhaust filters need to be replaced

as well. You will need to reset the

indicator after replacing any of these

components.

To do this, the vacuum cleaner must be

turned on.

^

Press the reset button.

The service indicator will go out and be

reset to its original position.

The reset feature only works properly

if the indicator light has already come

on, but not if the reset button is pres

-

sed in between filter changes.

Changing the batteries on the LED

handle (see fig. 15 + 16)

(depending on model)

You will need three AAA (1.5V) batteries.

a Loosen the screws on the cover.

b Press down on both sides of the

cover to remove.

c Take out the battery holder and

change the 3 batteries, making sure

they are inserted correctly.

d Replace the battery holder in the

direction of the arrows on the holder

and battery compartment, so that

both line up.

e Replace the cover and tighten the

screws.

Cleaning the floor roller of the floor

brush AllTeQ (see fig. 41)

(depending on model)

a Release the roller pin using a coin.

b Push and take out the roller axle.

c Take out the roller.

^

Remove all threads, hair etc. and

reinstall the roller and lock the roller

pin.

When to change the thread catcher

of the standard floor brush

(depending on model)

The thread catcher on the standard

floor brush can be replaced when the

pile is worn out.

en

19

Replacing the thread catchers

(see fig. 42 + 43)

^

Use a screwdriver or similar object to

remove the thread catchers from the

slots.

^

Insert the new thread catchers.

New thread catcher pads can be

purchased from any authorized Miele

vacuum dealer or Miele.

Cleaning and care

,

Turn off the vacuum and unplug

it from the outlet before performing

any maintenance work.

Vacuum cleaner and accessories

The vacuum cleaner and other plastic

accessories can be cleaned with a damp

cloth or a cleaner suitable for plastics.

,

Do not use abrasive, oil-based,

glass or all purpose cleaners!

Dust compartment

The dust compartment can, if necessary,

be cleaned using a dry cloth, dusting

brush or a second vacuum to remove any

dust.

Monitor the filter bag change indicator

and inspect all filters regularly. Clean or

replace them when necessary according

to these Operating Instructions.

,

Do not submerge the vacuum in

water. If moisture gets into the

appliance there is the risk of an

electric shock.

Frequently asked questions

The vacuum cleaner shuts off

automatically.

A warning light § comes on to

indicate overheating, depending on

model (see fig. 44).

A temperature sensor will turn off the

vacuum cleaner if it becomes too warm.

This problem can occur if, for example,

an object is blocking the suction hose or

the filter bag pores have become

clogged with fine dust. The cause could

also be a heavily soiled exhaust or dust

compartment filter. If this happens, turn

off the vacuum cleaner (press the On/Off

foot switch s) and unplug the power

plug from the electrical outlet.

Once the cause has been addressed,

allow the vacuum cleaner to cool for

approx. 20 - 30 minutes before

resuming vacuuming.

Technical service

In the event of a fault which you cannot fix

yourself please contact the Miele Service

Department at the phone number listed

on the back of this booklet.

^

Please quote the model type of your

appliance.

This can be found on the data plate on

the bottom of the vacuum.

Optional accessories

Always follow the flooring

manufacturer's cleaning and care

instructions.

You can order these and many other

products via the Miele website.

en

20

La page est en cours de chargement...

Miele C3 Alize Manuel utilisateur

Miele C3 Alize Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents