NOTE: The important safety instructions
appearing in this instruction sheet are not meant
to cover all possible conditions and situations
that may occur. It must be understood that
common sense, caution, and care must be used
with any electrical product.
ENGLISH XXXXXXXXXXX
INS-XXXXXXX REVXXXXXXX
XXXXXXXXXXXXX
XXXXXXX XXXXXX
1. Remove the lamp from packaging
and place on a flat surface.
2. Plug adaptor into a standard 120V
household outlet and rear of the lamp.
3. To turn the light on/off and adjust
brightness, touch the symbol.
4. Open the lid to use magnifier.
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
SAFETY WARNING: TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF
THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY
THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED
PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT
REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE
WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation
CAUTION! Any change or modification to product not
expressly recognized by OttLite Technologies voids OttLite’s
responsibility for proper function of product.
CAN ICES-005 (B)/NMB-005 (B)
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.2A
Output: 12V DC, 0.42A with a Male DC Plug
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Turn lamp off and WAIT UNTIL LAMP HEAD
COOLS before handling.
2. The LED panel might get hot after several
hours of continuous use, DO NOT place
your hands directly on the LED panel.
3. Never use with an extension cord unless the plug can be
fully inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by
the consumer.
6. INDOOR USE ONLY.
LED Magnifier Lamp
CSN9700PC CSN97G5P CSN97G5P-CA CSN9700PC-SHPR GX8279N
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology
with your new OttLite® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form
and return it today by mail, or register online by going to:
OttLite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Remove lamp from packaging and place on a flat
surface.
2. Plug adaptor into a standard 120V household outlet and
rear of the lamp.
3. To turn the light on/off and adjust brightness, touch the
symbol.
4. Open the lid to use magnifier.
SAFETY WARNING: TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD COOLS
before handling.
2. The LED panel might get hot after several hours of
continuous use, DO NOT place your hands directly on
LED light panel.
3. Never use with an extension cord unless the plug can be
fully inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be
replaced by the consumer.
6. INDOOR USE ONLY.
NOTE: The important safety instructions appearing in
this instruction sheet are not meant to cover all possible
conditions and situations that may occur. It must be
understood that common sense, caution, and care must be
used with any electrical product.
CAUTION! INDOOR USE ONLY. NEVER LEAVE THE MAGNIFIER
LENS UNATTENDED IN DIRECT SUNLIGHT OR WHERE LIGHT CAN SHINE
THROUGH IT AS THIS CAN POSE A RISK OF FIRE.
CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF
THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY
THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED
PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT
REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE
WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation
CAUTION! Any change or modification to product not
expressly recognized by OttLite Technologies voids
OttLite’s responsibility for proper function of product.
CAN ICES-005 (B)/NMB-005 (B)
POWER ADAPTER SPECIFICATION
Input: AC 100-240V, 50/60 Hz, 0.2A
Output: 12V DC, 0.42A with a Male DC Plug
ENGLISH LED Magnifier Lamp
INS-22-0711 REV052522
POWERED BY
NOTE: The important safety instructions
appearing in this instruction sheet are not meant
to cover all possible conditions and situations
that may occur. It must be understood that
common sense, caution, and care must be used
with any electrical product.
ENGLISH XXXXXXXXXXX
INS-XXXXXXX REVXXXXXXX
XXXXXXXXXXXXX
XXXXXXX XXXXXX
1. Remove the lamp from packaging
and place on a flat surface.
2. Plug adaptor into a standard 120V
household outlet and rear of the lamp.
3. To turn the light on/off and adjust
brightness, touch the symbol.
4. Open the lid to use magnifier.
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
SAFETY WARNING: TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF
THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY
THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED
PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT
REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE
WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation
CAUTION! Any change or modification to product not
expressly recognized by OttLite Technologies voids OttLite’s
responsibility for proper function of product.
CAN ICES-005 (B)/NMB-005 (B)
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.2A
Output: 12V DC, 0.42A with a Male DC Plug
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Turn lamp off and WAIT UNTIL LAMP HEAD
COOLS before handling.
2. The LED panel might get hot after several
hours of continuous use, DO NOT place
your hands directly on the LED panel.
3. Never use with an extension cord unless the plug can be
fully inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by
the consumer.
6. INDOOR USE ONLY.
Lampe loupe à DEL
CSN9700PC CSN97G5P CSN97G5P-CA CSN9700PC-SHPR GX8279N
FÉLICITATIONS!
Vous avez fait l’achat de la la meilleure
technologie en éclairage naturel avec votre produit OttLite.®
FORMULAIRE D’ENREGISTREMENT DE PRODUIT
Veuillez remplir le formulaire d’enregistrement du produit
ci-joint et le retourner aujourd’hui par courrier, ou inscrivez-
vous en ligne en allant sur: OttLite.com/warranty.
REMARQUE : CET ARTICLE EST COMPLÈTEMENT ASSEMBLÉ
1. Retirer la lampe de son emballage et placer sur une
surface plane.
2. Brancher l’adaptateur d’alimentation dans une prise
domestique CA de 120 V et arrière de la lampe.
3. Pour allumer/éteindre la lampe et régler la luminosité,
appuyez sur le symbole .
4. Ouvrez le couvercle pour utiliser la loupe.
AVERTISSEMENT : EN VUE DE RÉDUIRE
LES RISQUES D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE OU DE
BLESSURE CORPORELLE :
1. Éteindre et ATTENDRE QUE LA TÊTE DE LA
LAMPE SOIENT REFROIDIS avant de manipuler.
2. Le panneau à DEL situé dans l’abat-jour peut devenir
chaud après plusieurs heures d’utilisation continue : NE
PAS placez vos mains directement sur le panneau à DEL.
3. Ne jamais utiliser une rallonge à moins que la fiche ne
puisse être insérée à fond.
4. Ne pas modifier la fiche.
5. La tête de lampe fournie avec cet appareil ne peut pas
être remplacée par le client.
6. POUR USAGE À L’INTÉRIEUR SEULEMENT.
REMARQUE : Les directives de sécurité importantes citées
dans ce feuillet d’instructions ne sont pas exhaustives; elles
ne couvrent pas toutes les conditions ou situations possibles.
Nous vous prions donc d’utiliser une prudence d’usage et le
bon sens comme vous le faites avec tout produit électrique.
ATTENTION : À UTILISER EXCLUSIVEMENT EN
INTÉRIEUR. NE LAISSEZ JAMAIS LA LENTILLE DE LA LOUPE FACE AUX
RAYONS DU SOLEIL OU À UN ENDROIT OÙ DE LA LUMIÈRE PEUT PASSER
À TRAVERS AFIN D’ÉVITER UN RISQUE D’INCENDIE.
ATTENTION !
SI LE CÂBLE OU LE CORDON SOUPLE
EXTERNE DE CETTE LAMPE EST ENDOMMAGÉ, CELUI-CI DOIT ÊTRE
REMPLACÉ EXCLUSIVEMENT PAR LE FABRICANT, SON AGENT DE SERVICE
OU TOUTE PERSONNE COMPÉTENTE AFIN D’ÉVITER TOUT DANGER. POUR
USAGE À L’INTÉRIEUR SEULEMENT.
ATTENTION !
LA SOURCE DE LUMIÈRE DE CETTE
LAMPE N’EST PAS REMPLAÇABLE; LORSQUE LA SOURCE DE LUMIÈRE ARRIVE
À SA FIN DE VIE UTILE, LA LAMPE AU COMPLET DOIT ÊTRE REMPLACÉE.
SECTION 15 DES
RÈGLEMENTS DE LA FCC
Remarque : Ce matériel a été testé et a été déclaré conforme aux limites
en vigueur concernant les équipements numériques de catégorie B, en
vertu du paragraphe 15 de la réglementation FCC. Ces limites visent à
assurer une protection raisonnable contre tout brouillage nuisible dans
une installation résidentielle. Ce matériel produit, consomme et peut
émettre une énergie de radiofréquence et, s’il n’est pas installé et utilisé
conformément aux directives qui l’accompagnent, il peut entraîner
un brouillage nuisible des communications radio. Cependant, nous
ne garantissons pas l’absence de brouillage dans une installation en
particulier. Si, après avoir effectué une vérification en mettant l’appareil
hors tension puis sous tension, l’utilisateur s’aperçoit que ce matériel
provoque un brouillage nuisible à la réception des signaux de radio ou
de télévision, il lui faudra essayer de corriger ce brouillage en prenant
une ou plusieurs des mesures ci-dessous :
• Réorienter ou repositionner l’antenne de réception.
• Augmenter la distance entre l’appareil et le récepteur.
• Brancher le matériel dans une prise électrique située sur un
circuit différent de celui du récepteur.
•
Consulter le distributeur ou un technicien radio/télévision
expérimenté pour obtenir de l’aide.
Des changements ou modifications qui ne sont pas expressément
approuvés par la partie responsable de la conformité pourraient
annuler l’autorité de l’utilisateur de faire fonctionner l’équipement.
Cet appareil est conforme aux exigences de la Section 15 des règles de
la Commission fédérale des communications (FCC). Son utilisation est
assujettie aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d’interférences nuisibles
(2) Cet appareil doit accepter toute interférence reçue, y compris
les interférences pouvant entraîner son dysfonctionnement.
ATTENTION! Toute modification ou tout changement
apporté au produit, lorsque non reconnu expressément par
OttLite Technologies, annule la responsabilité d’OttLite en
ce qui a trait au bon fonctionnement du produit.
CAN ICES-005 (B)/NMB-005 (B)
FICHE TECHNIQUE DE L’ADAPTATEUR D’ALIMENTATION :
Entrée : CA 100-240V, 50/60 Hz, 0,2A
Sortie : 12V CC, 0,42A avec prise mâle CC
FRANÇAIS Lampe loupe à DEL
INS-22-0711 REV052522
ALIMENTÉ PAR
-
1
-
2
dans d''autres langues
Documents connexes
-
OttLite CS33600C Manuel utilisateur
-
-
-
-
-
-
-
-
-