Chief MCB1X2U Guide d'installation

Chief
Marque
Chief
Modèle
MCB1X2U
Catégorie
Mur
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
(Examples of Possible Configurations)
Stacking Back-to-Back Flat Panel Ceiling Mounts
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MCB1X2U / LCB1X2U
MCB1X2U / LCB1X2U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
model does not exceed maximum weights listed in table
below.
IMPORTANT ! : The MCB1X2U/LCB1X2U
mounts are
designed to be mounted to a 1-1/2" NPT or NPSM
following ANSI/ASME B1.20.1 (Schedule 40, 0.154"
minimum thickness steel or aluminum-ASTM B221)
threaded extension column (not included);
OR
a UL
Listed Chief CPA Series extension column (not included).
IMPORTANT ! : If attaching to a 1-1/2" NPT column, the
Chief UL Listed CPA261 or CPA264 adapter (not
included) is required.
NOTE: The MCB1X2U/LCB1X2U mounts are intended to be
used with the UL Listed Chief CPA Ceiling Plates (not
included): CPA330, CPA365, CPA395.
NOTE: The following UL Listed Chief ceiling plates WITHOUT
swaged collars (not included) may also be used:
CMA330, CMA345, CMA395.
--SAVE THESE INSTRUCTIONS--
MODEL Max Weight
Allowed for EACH
Display
Max Weight
Capacity of Entire
Mounting System
MCB1X2U 100 lbs
(45.4 kg) 400 lbs
(181.4 kg)
LCB1X2U 100 lbs
(45.4 kg) 400 lbs
(181.4 kg)
Installation Instructions MCB1X2U / LCB1X2U
3
DIMENSIONS
48.00
1219.2
MCB1U MOUNTS
MOUNTS CAN BE PLACED
AT ANY ANGLE IN RELATION
TO EACH OTHER
IF ATTACHING TO NPT COLUMN,
AN ADAPTOR COUPLER
WILL BE REQUIRED, SOLD SEPARATELY
DIMENSIONS: INCHES
[MILLIMETERS]
MCB1X2U / LCB1X2U Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions MCB1X2U / LCB1X2U
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/2" or 13mm
3/32" (included)
1/8" (included)
5/32" (included)
M5 (included)
A (1)
[CPA048P]
(includes installation
instructions)
B (2)
[MCB1U]
(includes parts, hardware
and installation instructions)
OR
B (2)
[LCB1U]
(includes parts, hardware
and installation instructions)
MCB1X2U / LCB1X2U Installation Instructions
6
INSTALLATION
IMPORTANT ! : Refer to Dimensions section (and to
Dimensions section in the MCB1U/LCB1U installation
instructions) to find specific dimension requirements BEFORE
proceeding with installation.
NOTE: The following procedure assumes that a UL Listed
Chief CPA or CMA ceiling plate (not included) has been
properly installed following instructions included with
ceiling plate.
Installing Column
1. Lay CPA048P column (A) on floor and carefully place
displays next to column. (See Figure 1)
2. Mark center of lower display onto column. (See Figure 1)
3. Measure one screen height up on the column from the first
mark. Add approximately 2 inches extra length to allow for
display tilt, and add additional length for any extra space
desired between displays. (See Figure 1)
4. Mark center of upper display onto column. (See Figure 1)
Figure 1
5. Install column following instructions included with column.
Installing MCB1U / LCB1U
1. Install MCB1U / LCB1U mounts (B) onto column following
instructions included with MCB1U/LCB1U.
IMPORTANT ! : Match the center marks on the MCB1U/
LCB1U mounts with the marks on the column. (See
Figure 2)
Figure 2
2. Complete installation following instructions included with
MCB1U/LCB1U.
3
2
Center of display
4
(A)
Center mark
(both sides of mount)
(MCB1U shown as example)
Installation Instructions MCB1X2U / LCB1X2U
7
MCB1X2U / LCB1X2U Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002405 Rev00
2014 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
02/14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief MCB1X2U Guide d'installation

Chief
Marque
Chief
Modèle
MCB1X2U
Catégorie
Mur
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes