Modern Forms WS-18818 Ceres Mode d'emploi

Marque: Modern Forms

Modèle: WS-18818 Ceres

Taper: Mode d'emploi

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.

INSTALLATION INSTRUCTION

188 – LED Wall Sconce

WS-18818

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”

the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out

or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.

CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements

locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt

(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et

ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire.

MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta

lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal

en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni

utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/CETL esta lámpara.

PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

HARDWARE

Wire Connector

Qty: 3pcs+1 Extra

7EAC112201

Junction Box Screw

Qty: 4pcs+2 Extra

7MPF0415C2

#8-32x9/16

Mounting Screw

Qty: 1 Extra

4MPF0412S2BB1(BB)

5/32” - 32x1/2

Burnished Brass (BB)

Wire Connector

Qty: 1 Extra

7EAC140901

Conversion Plate

Qty: 1 PC

4MBC201111BB2(BB)

Mounting Ring

Qty: 1pc

7MBC101501

Allen Wrench

Qty: 1pc

7MPE155003

Allen Screw

Qty: 1 Extra

7MPF0304K1

1/8”-40x3/16

Nickel Plating

A C D E F G HB

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.

INSTALLATION INSTRUCTION

188 – LED Wall Sconce

WS-18818

FIG.1 MOUNT ON SWITCH BOX

FIG.1 MOUNT ON JUNCTION BOX

Mounting Screw

Mounting

Backplate

Conversion Plate Mounting Ring

Junction

Box Screw Wire Connector

Junction Box

Wire Connector

Ground Wire

Lamp Body

Allen Screw

Junction

Box Screw

Wire Connector

Switch Box

Wire Connector

Ground Wire

Mounting

Backplate

Driver: 2w”L x 14”W x 18”H

Allen Wrench

Bubble Crystal Glass

(RPL-GLA-18818)

C E

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.

INSTALLATION INSTRUCTION

188 – LED Wall Sconce

WS-18818

MOUNTING BACK PLATE

MOUNTING RING DIMENSIONS CONVERSION PLATE DIMENSIONS

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

INSTALLATION

MOUNT ON 2” X 4” SWITCH BOX (FIG.1)

3. Remove the mounting screw (C) from the xture, and then take down the mounting back plate.

4. Connect the Driver’s input wires to switch box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet box

has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the

back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.

* Requires Driver to be recessed in the switch box.

5. Secure the mounting back plate to the switch box using junction box screws (B).The side of the mounting back plate marked

“GND” must face out.

6. Connect the Driver’s output wire to the xture wire as Shown in Fig.3. After wires are connected, tuck them carefully inside the switch box.

7. Secure the xture to the mounting back plate using the mounting screw (C).

8. Thread the bubble crystal glass into the xture. Secure it using Allen screw (H) and Allen wrench (G) provided.

MOUNT ON 4” X 4” JUNCTION BOX (FIG. 2)

3. Remove the mounting screw (C) from the xture, and then take down the mounting back plate.

4. Connect the Drivers’ input wires to junction box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet

box has a green and bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’ ground wire directly to

back plate using the green screw provided.

*Requires Driver to be recessed within the junction box.

5. Secure the mounting ring (F) to the junction box using junction box screws (B).The side of the mounting ring(F) marked “GND” must face out.

6. Secure the mounting back plate and conversion plate (E) to the mounting ring (F) with the junction box screws (B).

7. Connect the Driver’s output wire to the xture wire as Shown in Fig.3. After wires are connected, tuck them carefully inside the junction box.

8. Secure the xture to the mounting back plate using the mounting screw (C).

9. Thread the bubble crystal glass into the xture. Secure it using Allen screw (H) and Allen wrench (G) provided.

Fixture Wires

Black or

Smooth

Fixture Wires

White or

Rubbed

Fixture Wires

Bare Wire

(Ground)

House Wires

Black

(Hot)

House Wires

White

(Neutral)

House Wires

Green or Bare Copper

(Ground Wire)

Fig. 2 Wiring

dka

1a” 1s”

2a”

52”

1w”

1a” 1s”

88”

42”

1a”

4”

1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Trimless Junction Box Cover

MKCP-3040-WT

OVERALL COMPONENT DIMENSIONS

CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE

BEGINNING.

-Read all instructions before installing.

-System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

-When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

-Retain installation instructions for future maintenance reference.

WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern Forms

could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are

damaged or missing.

MISE EN GARDE: POUR ÉVITER TOUT CHOC ÉLECTRIQUE, ASSUREZVOUS QUE LE DISJONCTEUR SOIT MIS HORS TENSION AVANT DE

COMMENCER.

-Lisez toutes les instructions avant l’installation.

-Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements

locaux.

-Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec

les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus pour ce

produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez

contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

COMPONENT OVERVIEW

The trimless junction box cover is intended for installation to NEC approved 4” square junction boxes recessed in drywall and ush with the

support structure. It may be covered with spackle and/or plaster to conceal junction box visibility. It is to be connected to compatible Modern

Forms xtures. Refer to specications sheets for more information.

TYP

HARDWARE

Wire Connector

Qty: 3 (+1 Extra)

½” Plastic Spacer

Qty: 2

⁄”-40 x 1⁄” Long

Mounting Screw

Qty: 2 (+1 Extra)

¾” Plastic Spacer

Qty: 2

#8-32 x ¾” Long

Junction Box Screw

Qty: 2 (+1 Extra)

1” Plastic Spacer

Qty: 2

NOTE: This accessory is supplied with an optional mounting C-ring for

xture connection via ⁄” K.O. hole. This component may be omitted

from the installation if mounting xtures using #8 screw holes.

2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Trimless Junction Box Cover

MKCP-3040-WT

FIG. 1

FIG. 2

FIG. 4

TRIMLESS JUNCTION BOX COVER INSTALLATION:

The trimless junction box cover is compatible with NEC approved

4” square junction boxes recessed in drywall and ush with the

support structure.

1. Install compatible junction box (by others) to the framing

structure. Ensure the junction box is ush with the base or front

of framing structure (See FIG. 1).

2. Install the mounting plate to the junction box (See FIG. 2).

Ensure the spacer alignment base is facing outward.

FIG. 3

105mm

FIG. 5 FIG. 6

3. Determine the drywall thickness and select the appropriate

spacer to install between the mounting plate and the trimless

junction box cover (See FIG. 3).

NOTE: Only 1 matching pair of spacers are to be used per

installation.

4. Using the mounting screws provided, attach the trimless

junction box cover to the mounting plate (See FIG. 4).

5. Make a 4⁄” square cutout in drywall at the intended trimless

junction box cover location and proceed to install to framing

structure (See FIG. 5). Apply and nish spackle up to the center

hole of trimless junction box cover. Ensure #8 holes on the

cover are free of spackle. (See FIG. 6).

Mounting Plate

Plastic

Spacers

Trimless Junction Box Cover

Cover Mounting Screws

Ground Wire

Example: ½” Drywall (No Spacer)

⁄”½”

Spacer Alignment

Base

Spacer

Height

Drywall

Thickness

No Spacer ½”

½” ⁄”

¾” 1”

1” 1¼”

Junction Box

Screws

3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760