Installation Guide
IND673 | DOC-2002361
ProLine® Daintree EZ Connect Kit
Applicable Fixture Types: LWS and PSF Series.
Only for New Construction.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power o before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL approved wire for input/output connections.
Minimum size 18 AWG (0.75mm
2
).
Prepare Electrical Wiring
Electrical Requirements
• The LED luminaire must be connected to the mains
supply according to its ratings on the product label.
Grounding Instructions
• The grounding and bonding of the overall system
shall be done in accordance with National Electric
Code (NEC) Article 600 and local codes.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation
électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 18 AWG (0.75mm2).
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
Components Supplied
• EZ Connect Kit
ProLine® Daintree EZ Connect Kit Installation Guide
2
Installation
Follow instructions provided with xture to access LED driver enclosure.
Make the following electrical connections:
• ground from the kit to the xture ground
• pink and purple from the kit to the pink and purple from the LED driver
• red wire from the kit to the black line from the LED driver
• white wire from the kit to the white neutral from the LED driver
Remove knockout from end of xture and pass wires and conduit from kit into xture.
Secure conduit to xture with provided conduit nut.
1
3
2
www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
IND673 (Rev 12/13/2021) DOC-2002361 | REV-01
ProLine® Daintree EZ Connect Kit Installation Guide
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-005 (A) / NMB-005 (A)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at their own expense.
Connect the building line, neutral and ground to the kit line, neutral and ground shown below.
4
-
1
-
2
-
3
dans d''autres langues
- English: GE current IND673 User manual
Documents connexes
Autres documents
-
Lumination RPL Series Controls Accessory Controller Bracket Guide d'installation
-
-
-
-
Daintree GE Lumination LSA Series Guide d'installation
-
GE Horticulture Guide d'installation
-
GE Appliances IND523 Guide d'installation
-
-
Daintree Networked WMZ10 People Counting Sensor Guide d'installation
