Chief PDC2540 Guide d'installation
- Catégorie
- Supports de plafond à panneau plat
- Taper
- Guide d'installation
INSTALLATION INSTRUCTIONS
Plasma Dual Ceiling Mount
PDC Series
PDC Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING:
A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION:
A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING:
Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING:
Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the supporting structure and
the PDC does not exceed 400 lbs (181.44 kg) [200 lbs
(90.72 kg) each faceplate].
• The weight capacity of the PDC may be LIMITED to the
lowest weight capacity of any other component located
between the PDC and the supporting structure!
2" to 1-1/2" Reducer (NPT Threads)
103
4.06
11.42
290
2.56
65
16.45
418
14.00
356
14.00
356
413
16.27
2.50
64
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
ALL MEASUREMENTS ARE IN
THE FOLLOWING FORMAT:
[MILLIMETERS]
INCHES
WILL ADD BETWEEN 1/2" AND 2" IN DEPTH
SEE PSBU DRAWING ALSO.
ON THE MOUNT.
AND MAY AFFECT LOCATION OF DISPLAY
NOTE: CUSTOM INTERFACE BRACKET
Product Features
Weight Capacity
400 lbs
200 lbs per faceplate
Roll / Tilt / Yaw ±2.5° / +5°, -25° / 360°
25°
5°
DIMENSIONS
Installation Instructions PDC Series
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PDC Series Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
9/16" (14.3 mm)
PARTS
A (1)
B (1)
1/8"
C (1)
5/32"
D (2)
D1 (1)
D2 (1)
10-24
D3 (1)
10-24 x 3/8"
D4 (1)
3/16"
D5 (1)
4-40 x 2-1/2"
D6 (1)
4-40
D7 (1)
5/16-18
D8 (1)
5/16-18 x 2-3/4"
Installation Instructions PDC Series
5
INSTALLATION
Preparing for Installation
1. Attach click-lock flag kits (D) to PDC following instructions
included with the kits.
WARNING:
FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this component is attached can
support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
2. Determine if NPT pipe is 1-1/2" or 2".
• If NPT pipe is 1-1/2", proceed to Step 3.
• If NPT pipe is 2", loosen set screw and
remove the 1-1/2" to 2" pipe coupler, then
proceed to Step 3.(See Figure 1)
Figure 1
3. Thread the PDC (A) onto the NPT pipe extension and
tighten set screw. (See Figure 2)
Figure 2
4. Attach interface brackets to back of displays following
instructions included with the interface brackets.
Installing Displays on PDC
WARNING:
EXCEEDING MAXIMUM WEIGHT CAPACITY
CAN LEAD TO SERIOUS PERSONAL INJURY OR
DAMAGE TO EQUIPMENT! It is the installers responsibility
to ensure the total amount of weight placed on the mount
does not exceed 400 lbs (181.44 kg) [200 lbs (90.72 kg) each
faceplate].
WARNING:
DISPLAY MAY WEIGH IN EXCESS OF
40 LBS (18.14 KG)! Always use two people and proper lifting
techniques when installing or positioning display.
Figure 3
1. While supporting each side of display, align four mounting
buttons on display or interface bracket with four slots on
PDC. (See Figure 3)
2. Lower each display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes.(See Figure 4)
Set
Screw
Pipe
Coupler
(A)
1
Set
Screw
NPT
Pipe
(A)
Display
PDC Series Installation Instructions
6
Figure 4
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting
buttons are completely engaged in mounting holes.
NOTE:
Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 4)
3. Connect and secure power, audio and video cables.
Removing Displays from PDC
1. Disconnect all power/audio/video cables.
2. Remove bolt or padlock from faceplate (if used).
(See Figure 5)
NOTE:
The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
3. Pull back on flag on upper mounting hole and press pin
down down into "Open" position. (See Figure 5)
Figure 5
WARNING:
EACH DISPLAY MAY WEIGH IN EXCESS OF
40 LBS EACH! Always use two people and proper lifting
techniques when installing or positioning displays on PDC.
4. Carefully lift displays from PDC.
5. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 5)
Adjustments
Roll Adjustment
1. Loosen two Nylock nuts inside the PDC. (See Figure 6)
2. Using the slotted holes, adjust the roll, or horizontal
movement.
3. Tighten two Nylock nuts.
1
2
May remove
pin and nut and
move to lower holes
A padlock or bolt
may be placed
through latch holes
move to
3
2
Remove bolt
or padlock
if used
Pin in
"Open"
position -
Pin in
"Closed"
position -
5
move to
"Open"
position to
"Closed"
position
remove
display
after display
is removed.
Installation Instructions PDC Series
7
Figure 6
Pitch Adjustment
4. Loosen two screws on side of PDC. (See Figure 6)
5. Adjust to desired pitch, or vertical movement.
6. Tighten the screws on side of PDC.
x 2
x 2
4
3
2
1
x 2
x 2
5
6
(Display and faceplate
removed for clarity)
PDC Series Installation Instructions
8805-000115 Rev.D
©2008 Chief Manufacturing
www.chiefmfg.com
01/08
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F +86-755-8996 9217
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief PDC2540 Guide d'installation
- Catégorie
- Supports de plafond à panneau plat
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief PDC2540 Installation guide
Documents connexes
-
Chief Manufacturing PCS2051 Manuel utilisateur
-
Chief CMA480W Guide d'installation
-
-
Chief PDC2306 Guide d'installation
-
-
Chief PSS2000 Guide d'installation
-
-
-
Chief Manufacturing PTS2241 Manuel utilisateur
-