Dyna-Glo DGP321SNN-D Manuel utilisateur

Catégorie
Barbecues
Taper
Manuel utilisateur

Ce manuel convient également à

1
Français p.
XX
Español p.
XX
Rev. 08/09/2019
2 BURNER PREMIER
NATURAL GAS GRILL
Model # DGP321SNN / DGP321SNN-D
DGP321CNN / DGP321CNN-D
DGP321GNN / DGP321GNN-D
DGP321MNN / DGP321MNN-D
ATTACH YOUR RECEIPT HERE
Serial Number _____________________________ Purchase Date ______________________
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-447-4768, 8:00 a.m. – 4:30 p.m., CST, Monday – Friday or
e-mail us at [email protected].
Français p. 30
Español p. 59
2
TABLE OF CONTENTS
Safety Information ...................................................................................................................... 3
Package Contents ...................................................................................................................... 5
Hardware Contents .................................................................................................................... 6
Preparation ................................................................................................................................. 6
Assembly Instructions ................................................................................................................ 7
Operation Instructions ................................................................................................................. 19
Care and Maintenance ................................................................................................................. 21
Troubleshooting ........................................................................................................................... 24
Warranty ...................................................................................................................................... 26
Replacement Parts List .............................................................................................................. 27
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. Open lid.
4. If odor continues, keep away from
the appliance and immediately call your
local re department.
1. Do not store or use gasoline or
other ammable liquids or vapors
in the vicinity of this or any other
appliance.
2. An LP (liquid propane) cylinder not
connected for use shall not be stored
in the vicinity of this or any other
appliance.
3. This grill is for outdoor use only
and shall not be used in a building,
garage, under overhangs or any other
enclosed area.
4. Do not leave a lit grill unattended.
Keep children and pets away from the
grill at all times.
WARNING
DANGER
Assembler/Installer: This manual contains important information necessary for the proper
assembly and safe use of this appliance. Read and follow all warnings and instructions before
assembling and using this appliance. Leave these instructions with the consumer.
Consumer/User: Follow all warnings and instructions when using this appliance.
Retain these instructions for future reference.
3
DANGER
CAUTION
Do not use in an explosive atmosphere. Keep grill area clear and free from combustible
materials, gasoline and other ammable vapors and liquids.
Please read and understand this entire manual before attempting to assemble, operate or
install the product. If you have any questions regarding the product, please call customer
service at: 1-877-447-4768, 8:00 a.m. – 4:30 p.m., CST, Monday – Friday.
Never use charcoal or lighter uid with the grill.
Do not use gasoline, kerosene or alcohol for lighting.
This grill is not intended to be used in or installed on recreational vehicles and/or boats.
Always open grill lid slowly and carefully as heat and steam trapped within the grill can burn
you severely.
Never attempt to operate this grill using propane.
Always employ a qualied service agency to install all necessary natural gas supply
plumbing, manual shutoff valve, and quick-connect ttings.
SAFETY INFORMATION
This product and the fuels used to operate this product (liquid propane or natural gas), and
the products of combustion of such fuels, can expose you to chemicals including benzene,
which is known to the State of California to cause cancer and reproductive harm.
For more information go to www.p65Warnings.ca.gov
WARNING
4
SAFETY INFORMATION
• Do not place the grill under overhead
combustible construction or awnings.
Minimum clearance from sides and
back of unit to combustible construction,
36 inches (914.4mm) from sides and
back.
NOTE: The installation must conform
with local codes or, in the absence of
local codes, with either the National
Fuel Gas Code, ANSI Z223.1/NFPA 54,
Natural Gas and Propane Installation
Code, CSA B149.1, or Propane Storage
and Handling Code, B149.2.
Do not store or use gasoline or other ammable liquids or vapors in the vicinity of this or any other
appliance. Do not store ammables inside the cart of the grill.
An LP cylinder shall not be stored in the vicinity of this or any other appliance.
This grill is for use with natural gas only.
Never attempt to attach this grill to the self-contained propane system of a boat, camper trailer,
motor home or house.
Do not attempt to move the grill while it is lit or when it is hot. The casters should be locked when
not moving the grill.
Do not use the grill unless it is completely assembled and all parts are securely fastened and
tightened.
Keep all combustible items and surfaces at least 36 inches (91.44 cm) away from the grill at all
times.
Do not touch metal parts of grill until it has completely cooled (about 45 minutes) to avoid burns,
unless you are wearing protective gear (pot holders, gloves, BBQ mittens, etc…).
Do not alter this grill in any manner.
Clean and inspect the hose before each use. If there is evidence of abrasion, wear, cuts, or leaks,
the hose must be replaced prior to operating the appliance. The replacement hose assembly will
be that which is specied by the manufacturer, listed in the repair parts list in this manual.
Move gas hoses as far away as possible from hot surfaces and dripping hot grease. Never allow
the gas hose to touch heated surfaces.
Keep the grill’s valve compartment, burners and circulating air passages clean. Inspect the grill
before each use. Do not obstruct the ow of gas or ventilation air.
The use of alcohol, prescription or non-prescription drugs may impair the operator’s ability to
properly assemble or safely operate the grill.
Do not leave a lit grill unattended. Keep children and pets away from the grill at all times.
Do not place this grill on any type of tabletop surface. The grill should be placed on a at and level
surface.
Do not use the grill in high winds.
WARNING
36in
36in
914.4mm
914.4mm
CAUTION
5
PACKAGE CONTENTS
M
U
V
W
X
D
A
B
C
E
F
G
H
I
N
O
P
Q
R
T
S
K
J
L
Z
Y
B
C
D
A
H
G
E
F
Z
I
J YK
L
N
O
M
P
Q
R
V
T
S
U
W
X
PART DESCRIPTION QTY
A Hood Handle 1
B Temperature Gauge 1
C Grill Body Assembly 1
D Side Shelf Bracket A 2
E Right Side Shelf Assembly 1
F Side Shelf Bracket B 2
G Cart Right Side Panel Assembly 1
H Locking Swivel Caster 2
I Non-Locking Swivel Caster 2
J Cart Bottom Panel Shelf 1
K Bottom Panel Skirt Assembly 1
L Cart Left Side Panel Assembly 1
M Door Assembly 1
PART DESCRIPTION QTY
N Door Handle 1
O Left Side Shelf Assembly 1
P Heat Tent 2
Q Cooking Grate 2
R Warming Rack 1
S Control Knob 2
T Grease Pan 1
U Grease Cup 1
V Upper Front Door Brace 1
W Cart Rear Panel 1
X Door Magnet 2
Y Natural Gas Hose Holder 2
Z Quick Disconnect Coupling 1
6
HARDWARE CONTENTS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list on previous page and hardware contents above. If any part is missing or damaged, do
not attempt to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 50 minutes with 2 people.
Tools Required for Assembly and Leak Testing (not included): Phillips screwdriver, Spray bottle
M6x16
Bolt
Qty. 18
M6x12
Flat Bolt
Qty. 8
Shoulder
Bolt
Qty. 4
M6
Plain
Washer
Qty. 2
M6
Spring
Washer
Qty. 2
M6
Wing Nut
Qty. 2
M6x35
Bolt
Qty. 4
M3x10
Bolt
Qty. 4
THIS UNIT IS HEAVY. Two people required for safe assembly.
Two people required for safe assembly. Some parts may contain sharp edges. Wear protective
gloves if necessary. Read and follow all safety statements, warnings, assembly instructions and
use and care instructions before attempting to assemble and use.
CC
AA
BB
DD
FF
GG
EE
HH II JJ
CAUTION
Wrench
Qty. 1
M4x12
Bolt
Qty. 2
7
L
Wrench
x1
II
Hardware Used
G
I
H
II
ASSEMBLY INSTRUCTIONS
1. Attach the two locking swivel casters (H) and
the two non-locking swivel casters (I) to the
cart left side panel assembly (L) and the cart
right side panel assembly (G) with wrench (II).
Hardware Used
Wrench
2. Attach the cart left side panel assembly (L)
and the cart right side panel assembly (G) to
the cart bottom panel shelf (J) with four M6x16
bolts (AA).
DO NOT TIGHTEN BOLTS AT THIS TIME.
Hardware Used
AA
M6x16 Bolt
x 4
II
1
H
I
L
II
G
2
AA
J
G
L
8
L
AA
G
K
K
G
3
AA
L
K
G
G
K
ASSEMBLY INSTRUCTIONS
3. Insert the hook on the bottom panel skirt
assembly (K) into the slot on the cart left side
panel assembly (L) and the cart right side
panel assembly (G) as shown. Attach the
bottom panel skirt assembly (K) to the cart left
side panel assembly (L) and the cart right side
panel assembly (G) with two M6x16 bolts (AA).
Tighten ALL bolts securely from step 2.
Hardware Used
4. Attach the cart rear panel (W) to the cart left
side panel assembly (L) and the cart right side
panel assembly (G) with the four M6x16 bolts
(AA).
AA
W
L
G
4
AA
W
L G
Hardware Used
AA
AA
M6x16 Bolt
M6x16 Bolt
x 2
x 4
9
ASSEMBLY INSTRUCTIONS
5. Attach the upper front door brace (V) to the cart
left side panel assembly (L) and the cart right
side panel assembly (G) with four M6x35
bolts (EE).
6. Attach the door magnet (X) to the cart left side
assembly (L) with four M3x10 bolts (FF).
Hardware Used
EE
M6x35 Bolt
x 4
V
EE
G
L
5
G
EE
V
L
Hardware Used
FF
M3x10 Bolt
x 4
X
FF
G
L
6
L
G
FF
X
10
M
N
AA
AA
M6x16
Bolt x2
AA
Hardware Used
ASSEMBLY INSTRUCTIONS
8. Insert the bottom hinge pin of the cart bottom
panel skirt (K) into the lower hole on the door
assembly (M), then press the upper door spring
hinge pin into the hole on the upper front door
brace (V) as shown.
7. Attach the door handle (N) to the door
assembly (M) with two M6x16 bolts (AA).
7
Hardware Used
AA
N
M
8
V
K
M
AA
M6x16 Bolt
x 2
11
ASSEMBLY INSTRUCTIONS
9. Attach the hood handle (A) to the grill body
assembly (C) with two M6 wing nuts (DD), two
M6 spring washers (CC) and two M6 plain
washers (BB).
10. Remove pre-assembled wing nut and plain
washer from the temp gauge (B), then attach
the temp gauge (B) to the grill body assembly
(C). Secure the temp gauge (B) with wing nut
and plain washer removed earlier in this step.
Hardware Used
DD
M6 Wing Nut
x 2
BB
M6 Spring Washer
x 2
CC
M6 Plain Washer
x 2
CC
BB
A
C
DD
9
DD
A
C
CC
BB
B
10
B
C
12
ASSEMBLY INSTRUCTIONS
11. Carefully place the grill body (C) onto cart left
side panel assembly (L) and cart right side
panel assembly (G). Adjust the grill body (C)
so that the holes in the grill body (C) are
aligned with holes in the tabs of cart left side
panel assembly (L) and cart right side panel
assembly (G).
Note: Make sure the natural gas hose is inside
the cart. Secure the grill body (C) with four
M6X16 screws (AA).
Hardware Used
AA
M6x16 Bolt
M6x16 Bolt
M4x12 Bolt
x 4
12. Pre-assemble two M6x16 bolts (AA) onto the
cart right side panel assembly (G) and do not
tighten them. Make sure to leave a 5mm gap
between the bolt and the panel. Hang the
natural gas hose bracket onto the bolts and
tighten the two bolts. Put two pieces natural
gas hose holders (Y) in to the hose. Attach the
natural gas hose holders (Y) to the bottom shelf
(J) with two M4x12 bolts (JJ). NOTE: Make sure
the natural gas hose exits through the hole in
the cart rear panel (W).
Hardware Used
AA
JJ
x 2
x 2
AA
AA
M6x16
Bolt x4
AA
Hardware Used
C
11
C
G
AA
G
5mm
JJ
Y
Y
Y
12
G
JJ
Y
J
Y
Y
AA
W
13
GG
F
D
F
D
Hardware Used
GG
M6x10
Flat Bolt
x8
13
ASSEMBLY INSTRUCTIONS
13. Attach the side shelf bracket A (D) and side
shelf bracket B (F) to the grill body assembly
(C) with eight M6x12 at bolts (GG).
D
F
F
GG
Hardware Used
GG
M6x12 Flat Bolt
x 8
D
C
C
14
HH
HH
E
O
14
ASSEMBLY INSTRUCTIONS
14. Attach the left side shelf assembly (O) to the
brackets installed at step 13 with two shoulder
bolts (HH). Repeat it for right side shelf
assembly (E).
Hardware Used
HH
Shoulder Bolt
x 4
HH
HH
O
E
15
Q
R
P
ASSEMBLY INSTRUCTIONS
15. Put two heat tents (P) in place over each
burner.
15
P
R
Q
16. Put two cooking grates (Q) and one warming
rack (R) in place.
16
16
T
U
S
ASSEMBLY INSTRUCTIONS
17. Put the grease pan (T) and grease cup (U) into
place.
17
18. Assemble the two control knobs (S) to the
valve stems.
18
T
U
S
17
ASSEMBLY INSTRUCTIONS
Front View Rear View
Fully Assembled
The quick disconnect socket (Z) and supply gas line must be installed by a qualied service agency.
The supply connection must be made in accordance with local codes or, in the absence of local
codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, in the USA, of the Natural
Gas and Propane Installation Code, CSA B149.1, in Canada.
A properly sized manual shut-off valve must be installed between the frill and the gas supply piping.
The grill and its individual shut-off valve must be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 0.5 PSI (3.5 kPa).
The grill must be isolated from the gas supply piping system by closing its individual manual shut-
off valve during any pressure testing of the gas supply piping system at test pressures equal to or
less than 0.5 PSI (3.5 kPa).
Always connect the exible gas supply hose to the gas supply before opening the manual shutoff
valve.
1. Ensure that the natural gas shut-off valve is closed.
2. Remove the protective rubber caps from the plug
and sleeve ends of the quick disconnect ttings.
Check that the ttings are clean.
3. Retract the sleeve on the coupling as illustrated.
4. Insert the plug and release the sleeve as illustrated.
5. Push the plug into the sleeve until the sleeve snaps
forward to lock the plug in the coupling.
6. Open the natural gas shut-off valve.
1. Close natural gas supply at shut-off valve.
2. Push the sleeve back and gently pull out the plug.
3. Replace the protective rubber caps on the plug and
sleeve ends of the quick disconnect couplings.
CONNECTING THE GRILL TO THE NATURAL GAS SUPPLY
TO CONNECT:
TO DISCONNECT:
Z
Retract Sleeve
Release Sleeve
18
ASSEMBLY INSTRUCTIONS
CHECKING FOR LEAKS
After all connections are made, check all connections and ttings on the natural gas quick connector,
gas hose and manifold for leaks with a water and soap solution.
To prevent re or explosion while testing for a leak:
Always perform leak test prior to lighting the grill.
• Do not smoke while testing for a leak.
Always perform leak tests outdoors in a well-ventilated area.
Do not use any source of ame while testing for leaks.
• Do not use the grill until any and all leaks are corrected.
• If you are unable to correct a leak, close the natural gas shut-off and call a gas appliance service
agency.
PERFORM LEAK TEST
Prepare leak test solution by combining 1 part liquid dish soap with 3 parts water.
Total solution required is approximately 2 - 3 ounces (70 - 90 ml).
Put leak test solution in a spray bottle.
Ensure all control knobs are in the ‘OFF’ position.
Connect the gas hose to the gas supply.
Open the gas shut-off valve.
Spray leak test solution on all gas carrying connections and ttings. Presence of bubbles at areas
of applied test solution indicates a gas leak. If leaks are detected or you smell or hear gas, shut off
the gas supply valve immediately and repair or replace the defective part. Do not use the grill until all
leaks are corrected.
ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO
PREVENT FIRE, DAMAGE AND/OR INJURY.
In the connection process, make sure:
The gas supply hose does not come in contact or remain in contact with the rebox.
Only use the hose assembly provided! If a replacement is necessary, please call
our customer service center. Do not use replacement parts that are not intended for this grill.
WARNING
WARNING
CAUTION
19
OPERATION INSTRUCTIONS
Lighting The Grill
Before rst use:
Remove all hangings or plastic straps, if present. Before you cook on your new gas grill, it is important
to clean your grill with heat. To do this, operate the grill for approximately 15 minutes with the lid closed
and the control knob in the highest position. This will clean the internal parts by burning off any residue
and odor from the manufacturing process.
Do not lean over grill when lighting. Read instructions before lighting. Do not put pots on the
sear side burner. Using pots on the sear side burner will result in high carbon monoxide levels.
If the ame extinguishes accidentally during ignition or operation, immediately TURN OFF the
natural gas shut-off valve and then TURN OFF the control knob.
WARNING
CAUTION
1. Check that the control knobs are in the OFF position.
2. Open natural gas supply at shut-off valve.
3. Open the lid during the lighting process.
4. Depress and turn the control knob counter-clockwise from the OFF position, past the ignite
position, to the HIGH position. You may need to repeat this several times to ignite the burner.
If ignition does not occur in 5 seconds, turn the control knob(s) to the OFF position, wait 5 minutes, and
repeat the lighting procedure.
If the burner still does not light, check that the natural gas shut-off valve is open and follow the match
lighting instructions. Check the Troubleshooting Guide on page 24 for more information.
20
OPERATION INSTRUCTIONS
LIGHTING THE GRILL WITH A MATCH
1. Open the lid.
2. Insert a match in the end of the match holder that is installed on the inside of the cabinet door.
3. Light the match.
4. Immediately place the lit match through the spaces in the grill gates near the ports of the burner
between the heat tents as shown. Make sure the lit match is close to the burner ports.
5. Press in the control knob that operates the burner and rotate counter-clockwise to High
position and burner should light immediately.
6. Repeat 2~5 steps to lighting the remaining burners.
7. Adjust burners to desired cooking settings.
SHUTDOWN INSTRUCTIONS
1. Turn control knobs clockwise to the O OFF position.
2. Close natural gas shut-off valve.
3. Close lid.
Turn off natural gas shut-off valve when appliance is not in use.
Make sure all burners controls are off except for the burner being lit and the
burners that have been lit.
Main Burner Match Lighting
If ignition does not occur in 5 seconds, turn the control knob(s) to “O” OFF position, wait 5
minutes, and repeat the lighting procedure.
WARNING
CAUTION
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87

Dyna-Glo DGP321SNN-D Manuel utilisateur

Catégorie
Barbecues
Taper
Manuel utilisateur
Ce manuel convient également à