Simplicity 020305-2 Manuel utilisateur

Marque: Simplicity

Modèle: 020305-2

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Manual No. 209494GS Revision - (02/12/2009)

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Pressure Washer

Operator’s Manual

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association

(PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

material may be reproduced or transmitted in any form

without the express written permission of Briggs & Stratton

Power Products Group, LLC.

Thank you for purchasing this quality-built Briggs & Stratton pressure washer. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your

Briggs & Stratton pressure washer will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with pressure washers and

how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this pressure washer could be

used for, it is important that you read and understand these instructions thoroughly before attempting to start or operate this

equipment. Save these instructions for future reference.

This pressure washer requires final assembly before use. Refer to the Assembly section of this manual for instructions on

final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your pressure washer. Consult your Yellow Pages.

There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also

contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.

Pressure Washer

Model Number

Revision

Serial Number

Engine

Model Number

Type Number

Code Number

Date Purchased

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpack Pressure Washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Attach Handle and Accessory Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Add Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Add Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connect Hose and Water Supply to Pump. . . . . . . . . . . . . . . . . . . . . . . . . . 9

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Pressure Washer Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

How to Start Your Pressure Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

How to Stop Your Pressure Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

How to Use Accessory Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

How to Use ProjectPro® Nozzle System. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Applying Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Pressure Washer Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cleaning Detergent Siphoning Tube. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Automatic Cool Down System (Thermal Relief). . . . . . . . . . . . . . . . . . . . . 15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Pressure Washer Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Engine Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

After Each Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Winter Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Warranties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Emissions Control System Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Pressure Washer Owner Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Operator Safety

Equipment Description

Read this manual carefully and become familiar

with your pressure washer. Know its applications,

its limitations, and any hazards involved.

This pressure washer operates at a maximum of 2,200 PSI

(151.7 BARS) and a flow rate of up to 2.2 gallons per minute

(8.3 liters per minute). This high quality residential system

features an axial cam pump with stainless steel pistons,

automatic cool down system, detergent siphoning system,

nozzle extension with quick connect fitting, a variety of quick

connect ProjectPro® nozzles, heavy duty 30’ (9.1 m) hose,

and more.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

The Emission Control System for this pressure washer is

warranted for standards set by the Environmental Protection

Agency and the California Air Resources Board.

Important Safety Information

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE address practices not related to personal injury.

4 BRIGGSandSTRATTON.COM

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Operator’s Manual

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING This product contains lead and lead

compounds, known to the State of California to cause

birth defects or other reproductive harm. Wash your

hands after handling this product.

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve

OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Some chemicals or detergents may be harmful if inhaled

or ingested, causing severe nausea, fainting, or

poisoning.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open.

• Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

• Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful

vapors.

WARNING Risk of electrocution.

Contact with power source can cause electric

shock or burn.

• NEVER spray near power source.

WARNING Use of pressure washer can create

puddles and slippery surfaces.

Kickback from spray gun can cause you

to fall.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

pressure washer including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

NOTICE High pressure spray may damage fragile items

including glass.

• DO NOT point spray gun at glass when using red (0°) MAX

nozzle.

• NEVER aim spray gun at plants.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• If you have questions about intended use, ask dealer or contact

qualified service center.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all parts of

the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle provided

on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure washer.

• This equipment is designed to be used with Briggs & Stratton

Power Products authorized parts ONLY. If equipment is used with

parts that DO NOT comply with minimum specifications, user

assumes all risks and liabilities.

6 BRIGGSandSTRATTON.COM

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE

WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVER operate pressure washer without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

WARNING Risk of eye injury.

Spray can splash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity of

this equipment.

• NEVER substitute safety glasses or dry-condition goggles for

indirect vented safety goggles.

Assembly

Read entire operator’s manual before you attempt

to assemble or operate your new pressure washer.

Your pressure washer requires some assembly and is ready

for use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your pressure

washer, please call the pressure washer helpline at

(800) 743-4115. If calling for assistance, please have the

model, revision, and serial number from the identification

label available.

Unpack Pressure Washer

1. Remove the parts bag, accessories, and inserts

included with pressure washer.

2. Open carton completely by cutting each corner from

top to bottom.

3. Ensure you have all included items prior to assembly.

Items in the carton include:

• Main Unit

• Handle

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting

• Plastic Accessory Tray

• Oil Bottle

• Parts Bag (which includes the following):

• Operator’s Manual

• Owner’s Registration Card

• Bag of 4 Multi–Colored ProjectPro® Nozzles

• Handle/Accessory Tray Fastening Hardware Kit

(which includes):

• Carriage Bolts (2)

• Plastic Knobs (2)

• Tree Clips (4)

To prepare your pressure washer for operation, you will

need to perform these tasks:

1. Fill out and send in registration card.

2. Attach handle to main unit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

8. Select/attach quick connect ProjectPro® nozzle to

nozzle extension.

Attach Handle and Accessory Tray

1. Place handle (A) onto handle supports (B) connected to

main unit. Make sure holes (C) in handle align with

holes (C) on handle supports.

NOTE: It may be necessary to move the handle supports

from side to side in order to align the handle so it will slide

over the handle supports.

2. Insert carriage bolts (D) through holes from back of

unit and attach a plastic knob (E) from front of unit.

Tighten by hand.

3. Place accessory tray (F) over holes (H) on handle

(viewing from front of unit). Push the tree clips (G) into

the holes until they sit flat against the accessory tray.

4. Insert multi–colored ProjectPro® nozzles and other

supplied accessories in spaces provided in accessory

tray. See How to Use Accessory Tray.

Add Engine Oil

1. Place pressure washer on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• DO NOT attempt to crank or start the engine before it has been

properly serviced with the recommended oil. This may result in an

engine failure.

4. Replace oil fill cap/dipstick and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High

altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) or up to

15% MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE Avoid pressure washer damage.

Failure to follow Operator’s Manual for fuel

recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operate on gasoline. The

emission control system for this engine is EM (Engine

Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel (A) to fuel tank (B). Be

careful not to overfill. Allow about 1.5" (4 cm) (C) of

tank space for fuel expansion.

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. To

remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause

decreased performance, increased fuel consumption, and

increased emissions. See an Authorized Briggs & Stratton

dealer for high altitude adjustment information. Operation of

the engine at altitudes below 2,500 feet (762 meters) with

the high altitude kit is not recommended.

8 BRIGGSandSTRATTON.COM

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Connect Hose and Water Supply to Pump

NOTICE DO NOT run the pump without the water supply

connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

NOTE: Remove and discard the shipping caps from the

pump’s high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose and attach one end of hose

to base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high

pressure outlet on pump. Tighten by hand.

3. Run water through your garden hose for 30 seconds to

clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F (38°C)).

4. Before connecting garden hose to water inlet, inspect

inlet screen (A). Clean screen if it contains debris or

have it replaced if damaged. DO NOT run pressure

washer if inlet screen is damaged.

NOTICE Using a One Way Valve (vacuum breaker or check

valve) at pump inlet can cause pump or inlet connector

damage.

• There MUST be at least ten feet of unrestricted garden hose

between the pressure washer inlet and any device, such as a

vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Connect the garden hose (not to exceed 50 feet (15 m)

in length) to the water inlet. Tighten by hand.

6. Turn ON the water, press red button (B) on the gun and

squeeze the trigger to purge the pump system of air and

impurities.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all

of the following.

1. Be sure to read the Operator Safety section and How to

Use Your Pressure Washer in Operation section before

using pressure washer.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in the

engine crankcase.

4. Add proper fuel to fuel tank.

5. Check for properly tightened hose connections.

6. Check to make sure there are no kinks, cuts, or damage

to high pressure hose.

7. Provide a proper water supply at an adequate flow.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING Risk of eye injury.

Spray can splash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity of

this equipment.

• NEVER substitute safety glasses or dry-condition goggles for

indirect vented safety goggles.

Features and Controls

Read this Operator’s Manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

10 BRIGGSandSTRATTON.COM

A - Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes trigger

lock.

B - Nozzle Extension with Quick Connect — Allows you to

switch between four different nozzles.

C - Recoil Starter — Used for starting the engine manually.

D - Warning/Operating Instructions Tag — Identifies

hazards and proper procedure to start/stop pressure

washer.

E - Air Filter — Protects engine by filtering dust and debris

out of intake air.

F - Detergent Siphoning Tube/Filter — Use to siphon

pressure washer safe detergents into the low pressure

stream.

G - Primer Bulb — Prepares a cold engine for starting.

H - Throttle Lever — Sets engine in starting mode for recoil

starter and stops a running engine.

J- Fuel Tank — Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

K - Pump — Develops high pressure.

L - Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F. Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

M - Oil Fill/Dipstick — Check and fill with oil here.

N - High Pressure Hose — Connect one end to water pump

and the other end to spray gun.

P - Accessory Tray — Provides convenient storage for

standard and optional accessories, such as brushes,

turbo wands, etc.

R - Project Pro™ Nozzles — Detergent, 0°, 15° and 40°: for

various high pressure cleaning applications.

Items Not Shown:

Identification Label (near rear of base plate) — Provides

model and serial number of pressure washer. Please have

these readily available if calling for assistance.

High Pressure Outlet — Connection for high pressure hose.

Water Inlet — Connection for garden hose.

Operation

If you have any problems operating your pressure washer,

please call the pressure washer helpline at (800) 743-4115.

Pressure Washer Location

Clearances and Air Movement

Place pressure washer outdoors in an area that will not

accumulate deadly exhaust gas. DO NOT place pressure

washer where exhaust gas (A) could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes, or other openings that can allow exhaust

gas to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when positioning

pressure washer.

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these

instructions step-by-step. This starting information also

applies if you have let the pressure washer sit idle for at least

a day.

1. Place pressure washer near an outside water source

capable of supplying water at a flow rate greater than

3.2 gallons (12.1 l) per minute and no less than 20 PSI

(1.38 BARS) at pressure washer end of garden hose.

DO NOT siphon supply water.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See Assembly section.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure washer

pump.

NOTICE DO NOT run the pump without the water supply

connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Turn ON the water, press red button on the gun and

squeeze the trigger to purge the pump system of air and

impurities.

6. Attach nozzle extension to spray gun. Tighten by hand.

7. Choose ProjectPro® nozzle you want to use, pull back

on collar of nozzle extension, insert nozzle and release

collar. Tug on nozzle to make sure it is securely in

place. See How to Use ProjectPro® Nozzle System.

8. Move throttle lever to “Fast” position (B), shown as a

rabbit.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poisonous gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open.

WARNING Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank

causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of pressure

washer including overhead.

To start the engine for the very first time:

9A. Push primer bulb firmly 5 times, waiting 2 seconds

between each push.

To start engine thereafter:

9B. Press primer bulb firmly 3 times, waiting 2 seconds

between each push. For a warm engine, DO NOT press

primer bulb.

IMPORTANT: Before starting the pressure washer, be sure

you are wearing safety goggles as described below.

10. When starting engine, position yourself as

recommended below and grasp starter grip handle and

pull slowly until you feel some resistance. Then pull

rapidly to start engine.

11. Return starter grip handle slowly. DO NOT let rope

“snap back” against starter.

NOTE: Always keep the throttle lever in the “Fast” position

when operating the pressure washer.

How to Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for two

minutes.

2. Move throttle to SLOW position, then STOP position (A).

12 BRIGGSandSTRATTON.COM

WARNING Risk of eye injury.

Spray can splash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity of

this equipment.

• NEVER substitute safety glasses or dry-condition goggles for

indirect vented safety goggles.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

pressure washer including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

3. ALWAYS point gun in a safe direction and press red

button and squeeze spray gun trigger to release

retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even

when engine is stopped and water is disconnected.

How to Use Accessory Tray

The unit is equipped with an accessory tray with places to

store your spray gun, nozzle extension and ProjectPro®

nozzles. There is also a hook at the front of the accessory tray

to hold your high pressure hose.

NOTE: The extra hole in the tray is for storing a utility brush.

The extra clip in the tray is for storing a turbo nozzle. The

brush and turbo nozzle are NOT included with your pressure

washer. You can buy these items as optional accessories.

1. Place nozzle extension through hole on accessory tray

as shown.

2. Place spray gun through hole on accessory tray on

right side of unit as shown.

3. Hang high pressure hose on hook attached to

accessory tray on front of tray as shown.

4. Insert multi–colored ProjectPro® nozzles in spaces

provided in accessory tray.

How to Use ProjectPro® Nozzle System

The quick–connect on the nozzle extension allows you to

switch between four different ProjectPro® system nozzles.

ProjectPro® nozzles can be changed while pressure washer

is running once spray gun trigger lock is engaged. The

ProjectPro® nozzles vary the pressure and spray pattern as

shown.

Follow these instructions to change ProjectPro® nozzles:

1. Pull back collar on quick–connect and pull current

ProjectPro® nozzles off. Store ProjectPro® nozzles in

holder provided on the accessory tray.

Delicate

40° Yellow

1650 PSI

2.2 GPM

General

15° Orange

1950 PSI

2.1 GPM

Max

0° Red

2200 PSI

1.9 GPM

Black

Use to apply

detergent

Low Pressure

High Pressure

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVER exchange nozzles without the trigger lock being

engaged on the spray gun.

• DO NOT twist nozzles while spraying.

2. Select desired ProjectPro® nozzle:

• For delicate rinse (lower pressure and higher flow),

for gentle cleaning of cars/trucks, boats, RV’s, patio

furniture, lawn equipment, etc., select yellow

Delicate ProjectPro® nozzle.

• For general rinsing (medium pressure and medium

flow), ideal for most all purpose cleaning such as

home siding, brick patios, wood decks, driveways

and sidewalks, garage floors, etc., select orange

General ProjectPro® nozzle.

• For maximum rinsing (higher pressure and lower

flow), for stubborn or hard to reach surface such as

second story surfaces, paint removal, oil stains,

rust removal or other stubborn substances (tar,

gum, grease, wax, etc.), select red Max

ProjectPro® nozzle.

• To apply detergent, applies project specific cleaners

to help break down stubborn dirt and grime on a

variety of surfaces, select black ProjectPro®

cleaning detergent nozzle.

3. Pull back on collar, insert new ProjectPro® nozzle and

release collar. Tug on ProjectPro® nozzle to make sure

it is securely in place.

Usage Tips

• For most effective cleaning, keep spray tip from 8 to

24 inches (20 to 61 cm) away from cleaning surface.

• If you get spray tip too close, especially using a high

pressure spray tip, you may damage surface being

cleaned.

• DO NOT get closer than 6 inches (15 cm) when

cleaning tires.

Applying Detergent

To apply detergent, follow these steps:

1. Review use of ProjectPro® nozzles.

2. Prepare detergent solution as required by job.

3. Place small filter end of detergent siphoning tube into

detergent container.

NOTE: Make sure the filter is fully submerged in detergent

while applying detergent.

NOTICE Contact with the hot muffler can damage

detergent siphoning tube.

• When inserting the siphon into a detergent solution bottle, route

the tube so as to keep it from inadvertently contacting the hot

muffler.

14 BRIGGSandSTRATTON.COM

CAUTION Chemicals can cause bodily injury, and/or

property damage.

• NEVER use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

4. Make sure black detergent nozzle is installed.

NOTE: Detergent cannot be applied with the high pressure

ProjectPro® nozzle (Orange, Yellow or Red).

5. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Turn on water.

NOTICE You must attach all hoses before you start the

engine.

• Starting the engine without all the hoses connected and without

the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

6. Start engine following instructions How to Start Your

Pressure Washer.

7. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

long, even, overlapping strokes.

8. Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. DO NOT allow detergent to dry on

(prevents streaking).

IMPORTANT: You must flush the detergent siphoning

system after each use by placing the filter into a bucket of

clean water, then run the pressure washer in low pressure

for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1. Remove black detergent nozzle from nozzle extension.

2. Select and install desired high pressure nozzle following

instructions How to Use ProjectPro® Nozzle System.

3. Keep the spray gun a safe distance from the area you

plan to spray.

4. Apply a high pressure spray to a small area, then check

the surface for damage. If no damage is found, it is

okay to continue cleaning.

5. Start at the top of the area to be rinsed, working down

with same overlapping strokes as you used for washing

and applying detergent.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it

with clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of

clean water.

2. Remove high pressure nozzle from nozzle extension.

3. Select and install black detergent nozzle following

instructions How to Use ProjectPro® Nozzle System.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop

Pressure Washer and turn off water supply.

6. ALWAYS point gun in a safe direction and press red

button and squeeze spray gun trigger to release

retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even

when engine is stopped and water is disconnected.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reach temperatures above

125°F. The system engages to cool the pump by discharging

the warm water onto the ground.

WARNING Kickback from spray gun can cause you to

fall.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

Clean if clogged. Replace if perforated or torn.

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any qualified

dealer for service.

The pressure washer’s warranty does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain the pressure washer as instructed in this manual,

including proper storage as detailed in Winter Storage and

Long Term Storage.

NOTE: Should you have questions about replacing

components on your pressure washer, please call

(800) 743-4115 for assistance.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least once

each season. Follow the requirements in the Maintenance

Schedule chart above.

NOTE: Once a year you should clean or replace the spark

plug, clean or replace the air filter, and check the spray gun

and nozzle extension assembly for wear. A new spark plug

and clean air filter assure proper fuel-air mixture and help

your engine run better and last longer.

Pump Oil

DO NOT attempt any oil maintenance on this pump. The

pump is pre-lubricated and sealed from the factory, requiring

no additional maintenance for the life of the pump.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See the Emissions Warranty.

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check detergent siphoning tube and filter for damage.

6. Check spray gun and nozzle extension assembly for

leaks.

7. Rinse out garden hose to flush out debris.

Pressure Washer Maintenance

Clean Debris

Daily or before use, clean accumulated debris from cleaning

system. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure

washer. These openings must be kept clean and

unobstructed.

Pressure washer parts should be kept clean to reduce the

risk of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

Check and Clean Inlet Screen

Examine the screen on the pump’s water inlet. Clean it if the

screen is clogged or replace it if screen is damaged.

16 BRIGGSandSTRATTON.COM

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Check/clean water inlet screen

• Check high pressure hose

• Check detergent siphoning hose

• Check spray gun and assembly for leaks

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service air cleaner

Every 50 Hours or Yearly

• Change engine oil

• Inspect muffler and spark arrester

Every 100 Hours or Yearly

• Service spark plug

• Air cooling system

Check High Pressure Hose

The high pressure hose can develop leaks from wear,

kinking, or abuse. Inspect the hose each time before using it.

Check for cuts, leaks, abrasions or bulging of cover, damage

or movement of couplings. If any of these conditions exist,

replace the hose immediately.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged.

The tube should fit tightly on the barbed fitting. Examine the

tube for leaks or tears. Replace the filter or tube if either is

damaged.

Check Spray Gun

Examine the hose connection to the spray gun and make

sure it is secure. Test the trigger by pressing the red button

and making sure the trigger “springs back” into place when

you release it. You should not be able to press the trigger

without pressing the red button. Replace spray gun

immediately if it fails any of these tests.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure. The

principal cause of excessive pump pressure is a nozzle

clogged or restricted with foreign materials, such as dirt, etc.

To correct the problem, immediately clean the nozzle

following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point gun in a safe direction and press red

button and squeeze spray gun trigger to release

retained high water pressure.

3. Remove nozzle from end of nozzle extension.

4. Use a small paper clip to free any foreign material

clogging or restricting nozzle (A).

5. Remove nozzle extension from spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through nozzle extension. Back flush

between 30 to 60 seconds.

7. Reinstall nozzle into nozzle extension.

8. Reconnect nozzle extension to spray gun.

9. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Turn on water.

10. Start engine following instructions How to Start Your

Pressure Washer.

11. Test pressure washer by operating with each quick

connect nozzle.

O-Ring Maintenance

Purchase an O-Ring/Maintenance Kit, model 6048, by

contacting the nearest authorized service center. It is not

included with the pressure washer. This kit includes

replacement o-rings, rubber washer and water inlet filter.

Refer to the instruction sheet provided in the kit to service

your unit’s o-rings.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum pressure

rating of unit.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

Engine Maintenance

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

NOTE: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol with

“SJ/CF ENERGY CONSERVING” or higher, is an

acceptable oil at all temperatures. Use of synthetic

oil does not alter required oil change intervals.

Checking Oil Level

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure pressure washer is on a level surface.

2. Remove oil dipstick and wipe dipstick with clean cloth.

Replace and tighten dipstick. Remove and and check oil

level.

3. Verify oil is at “Full” mark (top hole) on dipstick.

Replace and tighten dipstick.

Adding Engine Oil

1. Make sure pressure washer is on a level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening to the

“Full” mark on dipstick. DO NOT overfill.

NOTICE Overfilling with oil may cause the engine to not

start, or hard starting.

• DO NOT overfill.

• If over the FULL mark on dipstick, drain oil to reduce oil level to

FULL mark on dipstick.

4. Replace and tighten dipstick.

Changing Engine Oil

If you are using your pressure washer under extremely dirty

or dusty conditions, or in extremely hot weather, change the

oil more often.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

18 BRIGGSandSTRATTON.COM

WARNING Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE

WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Full

Add

CAUTION Avoid prolonged or repeated skin contact

with used motor oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Change oil while engine is still warm from running, as

follows:

1. Drain fuel tank by running pressure washer until fuel

tank is empty.

2. Disconnect spark plug wire and keep it away from

spark plug.

3. Clean area around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

4. Tip your pressure washer to drain oil from oil fill into a

suitable container making sure you tip your unit away

from spark plug. When crankcase is empty, return

pressure washer to upright position.

5. Slowly pour recommended oil (about 20 oz. (0.6 l)) into

oil fill opening. Pause to permit oil to settle. Fill to

“Full” mark on dipstick.

6. Wipe dipstick clean each time oil level is checked. DO

NOT overfill.

7. Replace and tighten dipstick.

8. Wipe up any remaining oil.

9. Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged if

you run it with a dirty air cleaner. Service more often if

operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Remove screw (A).

2. Carefully remove air cleaner assembly to prevent debris

from falling into carburetor.

3. Take air cleaner assembly apart and clean all parts.

Wash foam air cleaner (B) in liquid detergent and

water. Squeeze dry in a clean cloth.

4. SATURATE foam air cleaner in engine oil and squeeze

in a clean cloth to remove excess oil.

5. Reinstall clean or new foam air cleaner in base (C).

6. Install air cleaner securely on carburetor with screw.

Service Spark Plug

Changing the spark plug will help your engine to start easier

and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned or

porcelain is cracked. Use the recommended

replacement plug. See Specifications.

4. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary (see

Specifications).

5. Install spark plug and tighten firmly.

Inspect Muffler and Spark Arrester

Inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect for

damage or carbon blockage. If replacement parts are

required, make sure to use only original equipment

replacement parts.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

pressure washer including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

Air Cooling System

Over time debris may accumulate in cylinder cooling fins and

cannot be observed without partial engine disassembly. For

this reason, we recommend you have a qualified service

dealer clean the cooling system per recommended intervals

(see Maintenance Schedule in beginning of Maintenance

section). Equally important is to keep top of engine free from

debris. See Clean Debris.

After Each Use

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and freeze

pump action. Follow these procedures after every use:

1. Shut off engine, turn off water supply, point gun in a

safe direction, press red button and squeeze trigger to

relieve trapped pressure, and let engine cool.

2. Disconnect hose from spray gun and high pressure

outlet on pump. Drain water from hose, gun, and nozzle

extension. Use a rag to wipe off the hose.

3. Place the spray gun, nozzle extension and nozzles in

the accessory tray. Hang high pressure hose on hook

attached to accessory tray.

4. Empty pump of all pumped liquids by pulling recoil

handle about six times. This should remove most liquid

in pump.

5. Store unit in a clean, dry area.

6. If storing for more than 30 days, see Long Term

Storage on next page.

20 BRIGGSandSTRATTON.COM

Keep areas within heavy line clear of debris.

WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

La page charge ...

Simplicity 020305-2 Manuel utilisateur

Marque: Simplicity

Modèle: 020305-2

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020305-2 User manual

Simplicity 020305-2 Manuel utilisateur

Simplicity 020305-2 Manuel utilisateur

dans d''autres langues

Documents connexes