Simplicity 020462-00 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur

Ce manuel convient également à

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 313757 Revision C
Pressure Washer
Operator’s Manual
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® pressure washer. We are pleased that you’ve
placed your condence in the Briggs & Stratton brand. When operated and maintained according to the
instructions in this manual, your Briggs & Stratton pressure washer will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with pressure
washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this
pressure washer could be used for, it is important that you read and understand these instructions thoroughly
before attempting to start or operate this equipment. Save these original instructions for future reference.
This pressure washer requires nal assembly before use. Refer to the Assembly section of this manual for
instructions on nal assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to nd Briggs & Stratton support and service for your pressure washer. Consult your
Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality
service. You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet
at BRIGGSandSTRATTON.COM.
Pressure Washer Engine
Model Number _____________________ Model Number ______________________
Revision __________________________ Type Number _______________________
Serial Number ______________________ Code Number _______________________
Date Purchased ___________________
Table of Contents
Operator Safety....................... 3
Assembly............................ 6
Features and Controls ................ 10
Operation........................... 11
Maintenance ........................ 15
Troubleshooting ..................... 21
Warranty ........................... 22
Product Specications ................ 24
Common Service Parts ............... 24
Copyright © 2015. Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON POWER PRODUCTS is a registered
trademark of Briggs & Stratton Corporation
Milwaukee, WI, USA
Operator Safety
Equipment Description
Read this manual carefully and become
familiar with your pressure washer. Know
its applications, its limitations, and any
hazards involved.
This pressure washer operates at a maximum of
2,700 PSI (186.1 BAR) and a ow rate of up to
2.3 gallons (8.7 liters) per minute. This high quality
residential system features an axial cam pump with
stainless steel pistons, automatic cool down system,
1 gallon (3.8 liters) cleaning tank system, nozzle
extension with quick connect tting, a multi tip nozzle,
heavy duty 30’ (9.1 m) hose, and more.
Every eort has been made to ensure that information
in this manual is accurate and current. However, we
reserve the right to change, alter, or otherwise improve
the product and this document at any time without prior
notice.
The Emission Control System for this pressure washer
is warranted for standards set by the Environmental
Protection Agency and the California Air Resources
Board.
Important Safety Information
Safety Symbols and Meanings
The safety alert symbol indicates a potential
personal injury hazard. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert
symbol to designate a degree or level of hazard
seriousness. A safety symbol may be used to
represent the type of hazard. The signal word
NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not
avoided, could result in minor or moderate injury.
NOTICE address practices not related to personal
injury.
Fire
Explosion
Toxic Fumes
Hot Surface
Moving
Parts
Electrical Shock
Slippery
Surface
Fall
Kickback
Flying
Objects
Fluid Injection
Operator’s
Manual
Chemical
Burn
Projectile
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
Some chemicals or detergents could be harmful if
inhaled or ingested, resulting in death, serious
injury, nausea, fainting or poisoning.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut o.
ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
Use a respirator or mask whenever there is a chance that
vapors may be inhaled when using chemicals.
Read all instructions with mask so you are certain the
mask will provide the necessary protection against
inhaling harmful vapors when using chemicals.
3
4 BRIGGSandSTRATTON.COM
WARNING The engine exhaust from this
product contains chemicals known to the State of
California to cause cancer, birth defects, or other
reproductive harm.
WARNING This product contains lead and lead
compounds, known to the State of California to
cause birth defects or other reproductive harm.
Wash your hands after handling this product.
WARNING Risk of electrocution.
Contact with power source could cause
electric shock or burn resulting in death or
serious injury.
NEVER spray near power source.
WARNING Use of pressure washer could create
puddles and slippery surfaces
causing you to fall resulting in death
or serious injury.
Kickback from spray gun could cause you to fall
resulting in death or serious injury.
Operate pressure washer from a stable surface.
The cleaning area should have adequate slopes and
drainage to reduce the possibility of a fall due to slippery
surfaces.
Be extremely careful if you must use the pressure washer
from a ladder, scaolding, or any other similar location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a re, resulting in
death or serious injury.
Contact with muer area could cause burns
resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
Replacement parts must be the same and installed in the
same position as the original parts.
WARNING Fuel and its vapors are extremely
ammable and explosive which could
cause burns, re or explosion
resulting in death or serious injury.
WHEN ADDING OR DRAINING FUEL
Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
Fill or drain fuel tank outdoors.
DO NOT overll tank. Allow space for fuel expansion.
If fuel spills, wait until it evaporates before starting engine.
Keep fuel away from sparks, open ames, pilot lights,
heat, and other ignition sources.
Check fuel lines, tank, cap and ttings frequently for
cracks or leaks. Replace if necessary.
DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
Ensure spark plug, muer, fuel cap, and air cleaner are in
place.
DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
DO NOT operate this product inside any building,
carport, porch, mobile equipment, marine applications, or
enclosure.
DO NOT tip engine or equipment at angle which causes
fuel to spill.
DO NOT spray ammable liquids.
WHEN TRANSPORTING, MOVING OR REPAIRING
EQUIPMENT
Transport/move/repair with fuel tank EMPTY or with fuel
shuto valve OFF (0).
DO NOT tip engine or equipment at angle which causes
fuel to spill.
Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL
IN TANK
Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
NEVER pull starter cord without rst relieving spray gun
pressure.
When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
NOTICE High pressure spray could damage fragile
items including glass.
DO NOT point spray gun at glass when using MAX (0°)
nozzle.
NEVER aim spray gun at plants.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
If you have questions about intended use, ask dealer or
contact qualied service center.
NEVER operate units with broken or missing parts, or
without protective housing or covers.
DO NOT by-pass any safety device on this machine.
DO NOT tamper with governed speed.
DO NOT operate pressure washer above rated pressure.
DO NOT modify pressure washer in any way.
Before starting pressure washer in cold weather, check all
parts of the equipment to be sure ice has not formed there.
NEVER move machine by pulling on hoses. Use handle
provided on unit.
This equipment is designed to be used with Briggs &
Stratton Power Products authorized parts ONLY. If
equipment is used with parts that DO NOT comply with
minimum specications, user assumes all risks and
liabilities.
5
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
If cut by uid, call physician immediately. DO NOT treat
as a simple cut.
DO NOT allow CHILDREN to operate pressure washer.
NEVER repair high pressure hose. Replace it.
NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
NEVER connect high pressure hose to nozzle extension.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
NEVER aim spray gun at people, animals, or plants.
DO NOT secure spray gun in open position.
DO NOT leave spray gun unattended while machine is
running.
NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Unintentional sparking could cause
re or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
Use approved spark plug tester.
DO NOT check for spark with spark plug removed.
WARNING Starter and other rotating parts
could entangle hands, hair, clothing, or
accessories resulting in serious injury.
NEVER operate pressure washer without protective
housing or covers.
DO NOT wear loose clothing, jewelry or anything that
could be caught in the starter or other rotating parts.
Tie up long hair and remove jewelry.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
DO NOT use caustic liquid with pressure washer.
Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
CAUTION
Excessively high operating speeds
could result in minor injury.
Excessively low operating speeds impose a heavy
load.
DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and ow when running at
governed speed.
DO NOT modify pressure washer in any way.
WARNING Risk of eye or bodily injury.
Spray could splash back or propel
objects resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
Always wear protective clothing such as a long-sleeved
shirt, long pants and close-toed shoes.
NEVER operate pressure washer when barefoot or
wearing sandals or shorts.
Assembly
Read entire operator’s manual before you
attempt to assemble or operate your new
pressure washer.
Your pressure washer requires some assembly and is
ready for use after it has been properly serviced with
the recommended oil and fuel.
If you have any problems with the assembly of your
pressure washer, please call the pressure washer
helpline at (800) 743-4115. If calling for assistance,
please have the model, revision, and serial number
from the identication label available.
Unpack Pressure Washer
1. Remove the parts bag, accessories, and inserts
included with pressure washer.
2. Open carton completely by cutting each corner
from top to bottom.
3. Ensure you have all included items prior to
assembly.
Items in the carton include:
Main Unit
• Handle
Cleaning Tank
High Pressure Hose
Spray Gun
Nozzle Extension with Quick Connect Fitting
Quick Connect Selector Nozzle
Plastic Accessory Tray
Hose Wrap
Oil Pouch
Parts Bag (which includes the following):
Operator’s Manual
Owner’s Registration Card
Handle/Accessory Tray Fastening Hardware Kit
(which includes):
Carriage Bolts (2)
Rope Guide (1)
Plastic Knobs for Handle (2)
Plastic Knob (1)
Tree Clips (8)
To prepare your pressure washer for operation,
you will need to perform these tasks:
1. Fill out and send in registration card.
2. Attach handle, cleaning tank and accessory tray
to main unit.
3. Connect detergent siphon hose to pump.
4. Add oil to engine crankcase.
5. Add fuel to fuel tank.
6. Connect high pressure hose to spray gun and
pump.
7. Connect water supply to pump.
8. Attach nozzle extension to spray gun.
9. Attach quick connect selector nozzle to nozzle
extension.
Attach Handle, Cleaning Tank and
Accessory Tray
1. Place handle (A) onto handle supports (B)
connected to main unit. Make sure holes (C) in
handle align with holes (C) on handle supports.
2. Insert handle carriage bolts (D) through holes from
inside of unit and attach a plastic knob (E) from
outside of unit. Tighten by hand.
NOTICE By loosening both knobs to the middle
section of the attachment bolt, the upper handle
can fold forward to store at atop the cold engine.
DO NOT fold handle down while the engine is hot.
3. Place cleaning tank (F) over holes (G) on handle
supports (viewing from back of unit). Push the tree
clips (H) into the holes until they sit at against the
cleaning tank.
4. Place accessory tray (J) over holes (K) on handle
(viewing from back of unit). Push the tree clips
(L) into the holes until they sit at against the
accessory tray.
C
A
B
C
E
D
F
G
H
6 BRIGGSandSTRATTON.COM
J
K
L
5. Insert quick connect selector nozzle and other
supplied accessories in spaces provided in
accessory tray. See How to Use Accessory Tray.
6. Insert rope guide (A) through handle and secure
with plastic knob (B). Tighten by hand. Route
engine recoil rope through guide.
7. Align hose wrap (C) to the back side of accessory
tray. Locate notch with “unlock” icon (D) on hose
wrap. Position notch at top with hose wrap in
vertical position. Clips in the back of accessory tray
should slide into the grooves on the inside surface
of hose wrap. Slide hose wrap on back of accessory
tray and rotate 1/8 turn until “locked” icon (E) is in
vertical position. Hose wrap is easily removed from
the accessory tray for wrapping and unwrapping of
the high pressure hose. A clip to secure the hose
on the reel makes it easy to wrap the hose while it is
detached from the accessory tray.
Attach Detergent Siphon Hose to Pump
Attach detergent siphon hose (F) to barbed hose tting
(G) closest to high pressure outlet connection (H) on
pump.
Add Engine Oil
1. Place pressure washer on a at, level surface.
2. Clean area around oil ll and remove yellow oil ll
cap/dipstick.
3. Hold neck of supplied oil pouch and remove cap.
4. Slowly pour contents of oil pouch into oil ll
opening. Checking oil level frequently, ll to FULL
mark (top hole) on dipstick.
NOTICE Pause to permit oil to settle. Wipe dipstick
clean each time oil level is checked. DO NOT overll.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
DO NOT attempt to crank or start the engine before it has
been properly serviced with the recommended oil. This
could result in an engine failure.
5. Replace oil ll cap/dipstick and fully tighten.
Add Fuel
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane/87 AKI (91 RON). For
high altitude use, see High Altitude.
Gasoline with up to 10% ethanol (gasohol) is
acceptable.
NOTICE Use of unapproved fuels could damage
pressure washer and voids warranty.
DO NOT use unapproved gasoline such as E15 and E85.
DO NOT mix oil in gasoline or modify engine to run on
alternate fuels.
To protect the fuel system from gum formation, mix
in a fuel stabilizer when adding fuel. See Storage.
All fuel is not the same. If you experience starting or
performance problems after using fuel, switch to a
dierent fuel provider or change brands. This engine is
certied to operate on gasoline. The emission control
system for this engine is EM (Engine Modications).
F
G
H
Full
Add
WARNING Fuel and its vapors are extremely
ammable and explosive which
could cause burns, re or explosion
resulting in death or serious injury.
WHEN ADDING FUEL
Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
Fill fuel tank outdoors.
DO NOT overll tank. Allow space for fuel expansion.
If fuel spills, wait until it evaporates before starting engine.
Keep fuel away from sparks, open ames, pilot lights,
heat, and other ignition sources.
Check fuel lines, tank, cap and ttings frequently for
cracks or leaks. Replace if necessary.
DO NOT light a cigarette or smoke.
A
B
7
C
D
E
1. Clean area around fuel ll cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel
tank (B). Be careful not to overll. To allow for fuel
expansion, do not ll above the bottom of the fuel
tank neck.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
High altitude
At altitudes over 5,000 ft. (1524 m), a minimum
85 octane / 85 AKI (89 RON) gasoline is acceptable.
To remain emissions compliant, high altitude
adjustment is required. Operation without this
adjustment will cause decreased performance,
increased fuel consumption, and increased emissions.
See an Authorized Briggs & Stratton dealer for high
altitude adjustment information. Operation of the
engine at altitudes below 2,500 ft. (762 m) with the
high altitude kit is not recommended.
Lubricate O-Rings
Lubrication of o-rings is extremely important for
installation and operation. The use of a lubricant
(petroleum or synthetic grease) during assembly helps
seat o-rings properly and provides an improved seal. It
also helps protect the o-ring from damage by abrasion,
pinching or cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant
on o-rings prior to assembling the garden hose to the
pump (C), high pressure hose (D), spray gun (E), and
nozzle extension (F).
Lubricate all connections shown below, following
these instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light
lm is all that is required.
3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible
(QC tting, M22 tting).
B
A
F
E
C
D
8 BRIGGSandSTRATTON.COM
Connect Hose and Water Supply to Pump
NOTICE DO NOT run the pump without the water
supply connected and turned on.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTICE Remove and discard the shipping caps from
the pump’s high pressure outlet and water inlet before
attaching hoses.
1. Uncoil high pressure hose and attach one end of
hose to base of spray gun. Tighten by hand.
2. Attach other end of high pressure hose to high
pressure outlet on pump. Tighten by hand.
3. Run water through your garden hose for
30 seconds to clean out any debris.
NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F (38°C)).
4. Before connecting garden hose to water inlet,
inspect inlet screen (A). Clean screen if it contains
debris or have it replaced if damaged. DO NOT
run pressure washer if inlet screen is damaged.
NOTICE Using a One Way Valve (vacuum breaker
or check valve) at pump inlet could cause pump or
inlet connector damage.
There MUST be at least 10 ft. (3 m) of unrestricted garden
hose between the pressure washer inlet and any device,
such as a vacuum breaker or check valve.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Connect the garden hose (not to exceed 50 ft.
(15 m) in length) to the water inlet. Tighten by hand.
6. Turn ON the water, press red button (B) on the
gun and squeeze the trigger to purge the pump
system of air and impurities.
Checklist Before Starting Engine
Review the unit’s assembly to ensure you have
performed all of the following.
1. Be sure to read the Operator Safety and
Operation before using pressure washer.
2. Make sure handle is in place and secure.
3. Check that oil has been added to proper level in
the engine crankcase.
4. Add proper fuel to fuel tank.
5. Check for properly tightened hose connections.
6. Check to make sure there are no kinks, cuts, or
damage to high pressure hose.
7. Provide a proper water supply at an adequate
ow.
A
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER connect high pressure hose to nozzle extension.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
B
9
Features and Controls
Read this Operator’s Manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
A - Recoil Starter — Used for starting the engine
manually.
B - Oil Fill/DipstickCheck, ll and drain engine oil
here.
C - Cleaning Tank Use to hold up to 1 gallon
(3.8 liters) of pressure washer safe detergent in tank.
D - Warning/Operating Instructions Tag — Identies
hazards and proper procedure to start/stop
pressure washer.
E - Engine Identication — Provides model, type and
code of engine. Please have these readily available
if calling for assistance.
F - Water Inlet — Connection for garden hose.
G - Pump — Develops high pressure.
H - Automatic Cool Down System — Cycles water
through pump when water reaches 125°-155°F
(51°-68°C). Warm water will discharge from pump
onto ground. This system prevents internal pump
damage.
J - Air Filter — Protects engine by ltering dust and
debris out of intake air.
K - Selector Nozzle — Contains ve dierent spray
pattern nozzles for various applications.
L - Engine Rocker Switch — Push this switch to
ON (I) position before using recoil starter. Push
switch to OFF (0) position for shutting o engine.
M - Fuel Tank — Fill tank with regular unleaded fuel.
Always leave room for fuel expansion.
N - Nozzle Extension with Quick Connect — Allows
you to switch between selector nozzle and optional
accessories.
P - Hose Wrap and High Pressure Hose — Hose
wrap provides easy transport and handling of the
high pressure hose. Connect one end of hose to
water pump and the other end to spray gun.
R - Spray Gun — Controls the application of water
onto cleaning surface with trigger device. Includes
trigger lock.
S - Accessory Tray — Provides convenient storage
for standard and optional accessories, such as
brushes, turbo wands, etc.
Items Not Shown:
High Pressure Outlet — Connection for high
pressure hose.
Identication Label (near rear of base plate)
Provides model and serial number of pressure washer.
Please have these readily available if calling for assistance.
D
J
H
,
G
A
E
P
M
N
S
L
B
F
C
R
K
10 BRIGGSandSTRATTON.COM
Operation
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
(800) 743-4115.
Pressure Washer Location
Carbon Monoxide Poisoning
Risk of Fire Clearances
How to Start Your Pressure Washer
To start your pressure washer for the rst time,
follow these instructions step-by-step. This starting
information also applies if you have let the pressure
washer sit idle for at least a day.
1. Place pressure washer near an outside water
source capable of supplying water at a ow rate
greater than 3.3 gallons (12.5 liters) per minute
and no less than 20 PSI (1.4 BAR) at pressure
washer end of garden hose. DO NOT siphon
supply water.
2. Check that high pressure hose is tightly
connected to spray gun and pump. See Assembly
section.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump.
NOTICE DO NOT run the pump without the water
supply connected and turned on.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Turn ON water, point gun in a safe direction, press
red button and squeeze trigger to purge pump
system of air and impurities.
6. Attach nozzle extension to spray gun. Tighten by
hand.
7. Pull back on collar of nozzle extension, insert
selector nozzle and release collar. Tug on selector
nozzle to make sure it is securely in place. See
How to Use Selector Nozzle.
8. Push engine rocker switch (A) to ON (I) position.
NOTICE Before starting the pressure washer, be sure
you are wearing safety goggles as described below.
A
Exhaust Port
Pointed away from
occupied spaces
11
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut o.
ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a re, resulting in death or serious
injury.
Keep at least 5 ft. (1.5 m) clearance on all sides of
pressure washer including overhead.
NOTICE This unit is equipped with a ReadyStart®
engine. A ReadyStart® engine means there is no
priming or choking required.
9. When starting engine, position yourself as
recommended and grasp starter grip handle and
pull slowly until you feel some resistance. Then
pull rapidly to start engine.
10. Return starter grip handle slowly. DO NOT let
rope “snap back” against starter.
Pressure washer is equipped with an automatic idle
control. The idle control will lower engine speed when
spray gun trigger is released.
How to Stop Your Pressure Washer
1. Release spray gun trigger and let engine idle for
two minutes.
2. Push engine rocker switch to OFF (0) position.
3. ALWAYS point gun in a safe direction and press
red button and squeeze spray gun trigger to
release retained high water pressure.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
NEVER pull starter cord without rst relieving spray gun
pressure.
When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a re, resulting in
death or serious injury.
Contact with muer area could cause burns
resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
Replacement parts must be the same and installed in the
same position as the original parts.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
DO NOT allow CHILDREN to operate pressure washer.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
NEVER aim spray gun at people, animals, or plants.
DO NOT secure spray gun in open position.
DO NOT leave spray gun unattended while machine is
running.
NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
Always be certain spray gun, nozzles and accessories
are correctly attached.
12 BRIGGSandSTRATTON.COM
How to Use Accessory Tray
The unit is equipped with an accessory tray with places
to store your spray gun and nozzle extension. There
is also a detachable hose wrap at the back of the
accessory tray to hold your high pressure hose.
1. Place nozzle extension and selector nozzle
through hole on accessory tray on left side of unit.
2. Place spray gun through hole on accessory tray
on right side of unit.
NOTICE You may also use the spray gun holder on
the accessory tray to store your spray gun, nozzle
extension and selector nozzle as shown in Features
and Controls section.
3. Wrap high pressure hose on hose wrap then
attach hose wrap to back of accessory tray.
4. Hook provided on back of accessory tray for
safely storing safety goggles.
How to Use Selector Nozzle
The selector nozzle allows you to switch between ve
dierent spray pattern nozzles. Spray patterns can be
changed while pressure washer is running once spray
gun trigger safety lock is engaged. The spray patterns
vary as shown below.
Follow these instructions to change nozzle
patterns:
1. Select desired spray pattern:
MAX - For stubborn or hard to reach surface
such as second story surfaces, paint removal,
oil stains, rust removal or other stubborn
substances (tar, gum, grease, wax, etc.).
GENERAL - For most all-purpose cleaning
such as home siding, brick patios, wood
decks, driveways and sidewalks, garage
oors, etc.
DELICATE - For gentle cleaning of cars/
trucks, boats, RV’s, patio furniture, lawn
equipment, etc.
FLUSH - For quick high ow clean up and
long reach cleaning of second story siding and
windows.
SOAP - For general soap applications or
to launch soap to second story siding and
windows.
2. Push button on selector nozzle, nozzle dial will
pop up.
3. Turn dial until desired spray pattern lines up with
button on selector nozzle.
4. Push dial in until it locks into place.
Usage Tips
For most eective cleaning, keep selector nozzle
from 8 to 24 inches (20 to 61 cm) away from
cleaning surface.
If you get selector nozzle too close, especially
using a high pressure spray pattern nozzle, you
may damage surface being cleaned.
DO NOT get closer than 6 inches (15 cm) when
cleaning tires.
2700 PSI
2.1 GPM
2650 PSI
2.2 GPM
2350 PSI
2.3 GPM
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER exchange spray tips without the trigger lock
being engaged on the spray gun.
DO NOT twist spray tips while spraying.
13
Applying Detergent
To apply detergent, follow these steps:
1. Review use of selector nozzle.
2. Prepare detergent solution as required by job.
3. Pour detergent into cleaning tank.
NOTICE The cleaning tank holds 1 gallon (3.8 litres).
4. Make sure “SOAP” nozzle is selected.
NOTICE Detergent cannot be applied with high
pressure nozzles (max, general, delicate or ush).
5. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
NOTICE You must attach all hoses before you start
the engine.
Starting the engine without all the hoses connected and
without the water turned ON could damage the pump.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
6. Start engine following instructions How to Start
Your Pressure Washer.
7. Rotate detergent shut-o valve on cleaning tank
to ON (I) position.
8. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward,
using long, even, overlapping strokes.
9. Allow detergent to “soak in” for 3-5 minutes
before washing and rinsing. Reapply as needed
to prevent surface from drying. DO NOT allow
detergent to dry on (prevents streaking).
Pressure Washer Rinsing
For Rinsing:
1. Turn detergent shut-o valve to OFF (0) position.
2. Select desired high pressure nozzle following
instructions How to Use Selector Nozzle.
3. Keep the spray gun a safe distance from the area
you plan to spray.
4. Apply a high pressure spray to a small area, then
check the surface for damage. If no damage is
found, it is okay to continue cleaning.
5. Start at the top of the area to be rinsed, working
down with same overlapping strokes as you used
for washing and applying detergent.
Automatic Cool Down System (Thermal
Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the
spray gun, circulating water in the pump can reach
temperatures above 125°-155°F (51°-68°C). The
system engages to cool the pump by discharging the
warm water onto the ground.
ON (I) Position
14 BRIGGSandSTRATTON.COM
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
DO NOT use caustic liquid with pressure washer.
Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING Kickback from spray gun could
cause you to fall resulting in death or
serious injury.
Operate pressure washer from a stable surface.
Be extremely careful if you must use the pressure washer
from a ladder, scaolding, or any other similar location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occurs rst. More frequent service is required when
operating in adverse conditions noted below.
1
Clean if clogged. Replace if perforated or torn.
2
Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance
and extend the life of the pressure washer. See any
qualied dealer for service.
The pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain the pressure washer as
instructed in this manual, including proper storage as
detailed in Winter Storage and Long Term Storage.
NOTICE Should you have questions about replacing
components on your pressure washer, please call
(800) 743-4115 for assistance.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. A new spark plug and clean
air lter assure proper fuel-air mixture and help
your engine run better and last longer. Follow the
requirements in the Maintenance Schedule chart
above.
Pump Oil
DO NOT attempt any oil maintenance on this pump.
The pump is pre-lubricated and sealed from the
factory, requiring no additional maintenance for the life
of the pump.
Emissions Control
Maintenance, replacement, or repair of the
emissions control devices and systems may
be performed by any non-road engine repair
establishment or individual. However, to obtain
”no charge” emissions control service, the work must
be performed by a factory authorized dealer. See the
Emissions Warranty.
Before Each Use
1. Check engine oil level.
2. Clean debris.
3. Check water inlet screen for damage.
4. Check high pressure hose for leaks.
5. Check detergent siphoning tube and tank for
damage.
6. Check spray gun and nozzle extension assembly
for leaks.
7. Rinse out garden hose to ush out debris.
Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from
cleaning system. Keep linkage, spring and controls
clean. Keep area around and behind muer free from
any combustible debris. Inspect cooling air slots and
openings on the pressure washer. These openings
must be kept clean and unobstructed.
Pressure washer parts should be kept clean to reduce
the risk of overheating and ignition of accumulated
debris.
Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
DO NOT insert any objects through cooling slots.
Use a soft bristle brush to loosen caked on dirt,
oil, etc.
Use a vacuum cleaner to pick up loose dirt and
debris.
Check and Clean Inlet Screen
Examine the screen on the pump’s water inlet. Clean
it if the screen is clogged or replace it if screen is
damaged.
First 5 Hours
Change engine oil
Every 8 Hours or Daily
Check/clean water inlet screen
1
Check high pressure hose
Check detergent siphoning tube/tank
Check spray gun and assembly for leaks
Clean debris
Check engine oil level
Every 50 Hours or Yearly
Clean engine air cleaner
2
Change engine oil
2
Inspect muer and spark arrester
Every 200 Hours or Yearly
Replace engine air cleaner
2
Yearly
Replace spark plug
Clean cooling system
2
15
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before
using it. Check for cuts, leaks, abrasions or bulging
of cover, damage or movement of couplings. If any of
these conditions exist, replace the hose immediately.
Check Detergent Siphoning Tube/Tank
Examine the detergent tank and detergent siphoning
tube and clean if clogged. The tube should t tightly on
the barbed tting of the pump and detergent shut-o
valve. Examine the tube for leaks or tears. Replace the
tank or tube if either is damaged.
Detergent Siphoning Check Ball
Occasionally check ball in detergent siphoning
system may become stuck from storage, dried soap,
or minerals in water. The check ball can be freed by
performing the following:
NOTICE Before performing this procedure, be sure
you are wearing safety goggles as described below.
1. Shut o engine and turn o water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove detergent siphoning hose from barbed
tting on pump.
4. Using a rm, blunt object 7/64” in diameter or
smaller, by at least 1” long, such as an Allen
wrench, slowly insert the object into the barbed
tting until you meet resistance. This resistance is
the check ball.
5. Slowly push down until you feel the ball move
slightly, push no more than 1/8”. Slight pressure
may be required to free the ball.
6. Repeat steps 4 and 5 if necessary.
7. Reinstall detergent siphoning hose onto barb
tting.
8. Treat with PumpSaver as described in Protecting
the Pump during storage to prevent reoccurrence.
Check Spray Gun
Examine the hose connection to the spray gun and
make sure it is secure. Test the trigger by pressing the
red button and making sure the trigger “springs back”
into place when you release it. You should not be able to
press the trigger without pressing the red button. Replace
spray gun immediately if it fails any of these tests.
Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is
a nozzle clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the nozzle following these instructions:
1. Shut o engine and turn o water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove nozzle selector from end of nozzle
extension.
4. Use a small paper clip to free any foreign material
clogging or restricting any of the nozzles (A).
5. Remove nozzle extension from spray gun.
A
16 BRIGGSandSTRATTON.COM
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER repair high pressure hose. Replace it.
Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
6. Using a garden hose, remove additional debris
by back ushing water through nozzle extension.
Back ush between 30 to 60 seconds.
7. Reinstall nozzle selector into nozzle extension.
8. Reconnect nozzle extension to spray gun.
9. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
10. Start engine following instructions How to Start
Your Pressure Washer.
11. Test pressure washer by operating with each
nozzle spray pattern (max, general, delicate, soap
or ush).
O-Ring Maintenance
Purchase an O-Ring/Maintenance Kit, model 705001,
by contacting the nearest authorized service center.
It is not included with the pressure washer. This kit
includes replacement o-rings, rubber washer and water
inlet lter. Refer to the instruction sheet provided in the
kit to service your unit’s o-rings.
Engine Maintenance
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certied oils for best performance. Other high-quality
detergent oils are acceptable if classied for service
SF, SG, SH, SJ or higher. DO NOT use special
additives.
Outdoor temperatures determine the proper oil
viscosity for the engine. Use the chart to select the
best viscosity for the outdoor temperature range
expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard
starting.
** Above 80°F (27°C) the use of 10W30 may cause
increased oil consumption. Check oil level more frequently.
Checking Oil Level
Oil level should be checked prior to each use or
at least every 8 hours of operation. Keep oil level
maintained.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean
cloth. Replace and tighten dipstick. Remove and
and check oil level.
3. Verify oil is at FULL mark (top hole) on dipstick.
Replace and tighten dipstick.
Adding Engine Oil
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in Checking Oil
Level.
3. If needed, slowly pour oil into oil ll opening to
the FULL mark (top hole) on dipstick. DO NOT
overll.
NOTICE Overlling with oil could cause the engine
to not start, or hard starting.
DO NOT overll.
If over the FULL mark on dipstick, drain oil to reduce oil
level to FULL mark on dipstick.
4. Replace and tighten dipstick.
Full
Add
17
WARNING Unintentional sparking could cause
re or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
Use approved spark plug tester.
DO NOT check for spark with spark plug removed.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
Changing Engine Oil
If you are using your pressure washer under extremely
dirty or dusty conditions, or in extremely hot weather,
change the oil more often.
KEEP OUT OF REACH OF CHILDREN.
DON’T POLLUTE. CONSERVE
RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
Change oil while engine is still warm from
running, as follows:
1. Drain fuel tank by running pressure washer until
fuel tank is empty.
2. Disconnect spark plug wire and keep it away from
spark plug.
3. Clean area around oil ll, remove oil ll cap/
dipstick. Wipe dipstick clean.
4. Tip your pressure washer to drain oil from oil ll
into a suitable container making sure you tip your
unit away from spark plug. When crankcase is
empty, return pressure washer to upright position.
5. Slowly pour recommended oil (about 20 oz.
(0.6 liters)) into oil ll opening. Pause to permit oil
to settle. Fill to FULL mark (top hole) on dipstick.
6. Wipe dipstick clean each time oil level is checked.
DO NOT overll.
7. Replace and tighten dipstick.
8. Wipe up any remaining oil.
9. Reconnect spark plug wire to spark plug.
Service Air Cleaner
Your engine will not run properly and may be damaged
if you run it with a dirty air cleaner. Service more often
if operating under dirty or dusty conditions.
To service the air cleaner, follow these steps:
1. Slide air cleaner lever (A) to unlock (
) position
and tilt cover (B) down.
2. Carefully remove air cleaner to prevent debris
from falling into carburetor.
3. Wash foam air cleaner (C) in liquid detergent and
water. Squeeze dry in a clean cloth.
4. SATURATE foam air cleaner in engine oil and
squeeze in a clean cloth to remove excess oil.
5. Reinstall clean or new foam air cleaner in
base (D).
6. Tilt cover up and slide lever to lock (
) position.
Service Spark Plug
Changing the spark plug will help your engine to start
easier and run better.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
3. Replace spark plug if electrodes are pitted,
burned or porcelain is cracked. Use the
recommended replacement plug. See
Specications.
4. Check electrode gap with wire feeler gauge and
reset spark plug gap to recommended gap if
necessary (see Specications).
5. Install spark plug and tighten rmly.
Inspect Muer and Spark Arrester
Inspect the muer for cracks, corrosion, or other
damage. Remove the spark arrester, if equipped, and
inspect for damage or carbon blockage. If replacement
parts are required, make sure to use only original
equipment replacement parts.
CAUTION Avoid prolonged or repeated skin
contact with used motor oil.
Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
D
C
B
A
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a re, resulting in
death or serious injury.
Contact with muer area could cause burns
resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
Replacement parts must be the same and installed in the
same position as the original parts.
18 BRIGGSandSTRATTON.COM
Air Cooling System
Over time debris may accumulate in cylinder cooling
ns and cannot be observed without partial engine
disassembly. For this reason, we recommend you have
a qualied service dealer clean the cooling system per
recommended intervals (see Maintenance Schedule in
beginning of Maintenance section). Equally important
is to keep top of engine free from debris. See Clean
Debris.
Carburetor Adjustment
The carburetor on this engine is low emission. It is
equipped with a non-adjustable idle mixture valve.
Top speed has been set at the factory. If adjustment is
required, see an authorized service dealer.
After Each Use
Water should not remain in the unit for long periods
of time. Sediments or minerals can deposit on pump
parts and freeze pump action. Follow these procedures
after every use:
1. Flush detergent system by turning its detergent
shut-o valve to OFF (0) position and run pressure
washer with the SOAP nozzle selected. Flush for
one to two minutes.
2. Shut o engine, turn o water supply, point gun
in a safe direction, press red button and squeeze
trigger to relieve trapped pressure, and let engine
cool.
3. Disconnect hose from spray gun and high
pressure outlet on pump. Drain water from hose,
spray gun, and nozzle extension. Use a rag to
wipe o the hose.
4. Place the spray gun, nozzle extension and
selector nozzle in the accessory tray. Wrap high
pressure hose on hose wrap then attach hose
wrap to back of accessory tray.
5. Empty pump of all pumped liquids by pulling recoil
handle about six times. This should remove most
liquid in pump.
6. Store unit in a clean, dry area.
7. If storing for more than 30 days, see Long Term
Storage on next page.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING Fuel and its vapors are extremely
ammable and explosive which
could cause burns, re or explosion
resulting in death or serious injury.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN
TANK
Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
CAUTION Excessively high operating speeds
could result in minor injury.
Excessively low operating speeds impose a heavy
load.
DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and ow when running at
governed speed.
DO NOT modify pressure washer in any way.
19
Winter Storage
NOTICE You must protect your unit from freezing
temperatures.
Failure to do so will permanently damage your pump and
render your unit inoperable.
Freeze damage is not covered under warranty.
To protect the unit from freezing temperatures:
1. Empty cleaning tank as follows:
a. Rotate detergent shut-o valve to OFF (0)
position.
b. Disconnect hose connected to barbed tting
on pump. Place end of hose into suitable
container.
c. Rotate detergent shut-o valve to ON (I)
position and open the tank’s cover. Gravity will
empty tank contents into container.
d. Reconnect hose to barbed tting on pump.
Add 1 pint (0.5 liter) of clean fresh water to
cleaning tank and close tank’s cover.
2. Flush cleaning tank by turning its detergent
shut-o valve to ON (I) position and run pressure
washer with SOAP nozzle selected. Flush until
tank is empty. Turn detergent shut-o valve to
OFF (0) position.
3. Follow steps 2-5 in the previous section After
Each Use.
4. Use pump saver, Model 6039, to treat pump. This
minimizes freeze damage and lubricates pistons
and seals.
5. If pump saver is not available, connect a 3 ft.
(92 cm) section of garden hose to water inlet
adapter. Pour RV-antifreeze (antifreeze without
alcohol) into hose. Pull recoil handle twice.
Disconnect 3 ft. (92 cm) hose.
6. Store unit in a clean, dry area.
Long Term Storage
If you do not plan to use the pressure washer for more
than 30 days, you must prepare the engine and pump
for long term storage.
Protect Fuel System
Fuel Additive:
Fuel can become stale when stored over 30 days.
Stale fuel causes acid and gum deposits to form in
the fuel system or on essential carburetor parts. To
keep fuel fresh, use Briggs & Stratton® Advanced
Formula Fuel Treatment & Stabilizer, available
wherever Briggs & Stratton genuine service parts are
sold.
There is no need to drain gasoline from the engine
if a fuel stabilizer is added according to instructions.
Run the engine for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a
fuel stabilizer, it must be drained into an approved
container. Run the engine until it stops from lack
of fuel. The use of a fuel stabilizer in the storage
container is recommended to maintain freshness.
Change Engine Oil
While engine is still warm, drain oil from crankcase.
Rell with recommended grade. See Changing Engine
Oil in Engine Maintenance.
Protecting the Pump
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver, Model 6039,
to treat pump. This prevents freeze damage and
lubricates pistons and seals.
NOTICE PumpSaver is available as an optional
accessory. It is not included with the pressure washer.
Contact the nearest authorized service center to
purchase Pump Saver.
NOTICE You must protect your unit from freezing
temperatures.
Failure to do so will permanently damage your pump and
render your unit inoperable.
Freeze damage is not covered under warranty.
To use PumpSaver, make sure the pressure washer is
turned o and disconnected from supply water. Read
and follow all instructions and warnings given on the
PumpSaver container.
Other Storage Tips
1. DO NOT store fuel from one season to another
unless it has been treated as described in Protect
Fuel System.
2. Replace fuel container if it starts to rust. Rust and/
or dirt in fuel can cause problems if it’s used with
this unit.
3. Cover unit with a suitable protective cover that
does not retain moisture.
4. Store unit in a clean and dry area.
20 BRIGGSandSTRATTON.COM
WARNING Storage covers could cause a re
resulting in death or serious injury.
DO NOT place a storage cover over a hot pressure
washer.
Let equipment cool for a sucient time before placing
the cover on the equipment.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Simplicity 020462-00 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues