Dometic CAM35 Mode d'emploi

Taper
Mode d'emploi

Ce manuel convient également à

CAM35
Rear View Video Camera
Installation and Operating Manual. . . . . . . . 9
Rückfahrvideokamera
Montage- und Bedienungsanleitung . . . . .20
Caméra vidéo de recul
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cámara de vídeo de marcha atrás
Instrucciones de montaje y de uso . . . . . . .42
Câmara de marcha-atrás
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Videocamera per la retromarcia
Istruzioni di montaggio e d’uso . . . . . . . . .64
Achteruitrijvideocamera
Montagehandleiding en
gebruiksaanwijzing . . . . . . . . . . . . . . . . . . .75
Bakvideokamera
Monterings- og betjeningsvejledning . . . .86
Backningsvideokamera
Monterings- och bruksanvisning . . . . . . . . 97
Ryggevideokamera
Monterings- og bruksanvisning. . . . . . . . 107
Peruutusvideokamera
Asennus- ja käyttöohje . . . . . . . . . . . . . . . 118
Видеокамера заднего вида
Инструкция по монтажу
и эксплуатации . . . . . . . . . . . . . . . . . . . . . 128
Kamera cofania
Instrukcja montażu i obsługi. . . . . . . . . . . 140
Cúvacia kamera
Návod na montáž a uvedenie
do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 151
Couvací kamera
Návod k montáži a obsluze . . . . . . . . . . . 162
Tolatókamera
Szerelési és használati útmutató . . . . . . . 173
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
DRIVING SUPPORT
PERFECTVIEW
CAM35-IO-16s.book Seite 1 Dienstag, 21. Februar 2017 5:31 17
CAM35-IO-16s.book Seite 2 Dienstag, 21. Februar 2017 5:31 17
CAM35
3
1
2
3
4
5
CAM35-IO-16s.book Seite 3 Dienstag, 21. Februar 2017 5:31 17
CAM35
4
1
2
5
4
3
CAM35 REAR
6
1
2
5
4 3
CAM35 TWIN
7
CAM35-IO-16s.book Seite 4 Dienstag, 21. Februar 2017 5:31 17
CAM35
5
1
2
4
3
8
9
CAM35-IO-16s.book Seite 5 Dienstag, 21. Februar 2017 5:31 17
CAM35
6
0
1
a
CAM35-IO-16s.book Seite 6 Dienstag, 21. Februar 2017 5:31 17
CAM35
7
1 4
6
32
5
b
+12 Vg
ws
rtsw
ge
1
6
3
2
7
c
AB
d
CAM35-IO-16s.book Seite 7 Dienstag, 21. Februar 2017 5:31 17
CAM35
8
5 Nm
e
CAM35-IO-16s.book Seite 8 Dienstag, 21. Februar 2017 5:31 17
EN
CAM35 Explanation of symbols
9
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
Table of contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
6 Fitting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
7 Cleaning and caring for the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
8 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
9 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
10 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
1 Explanation of symbols
!
A
I
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or
serious injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
CAM35-IO-16s.book Seite 9 Dienstag, 21. Februar 2017 5:31 17
EN
Safety and installation instructions CAM35
10
2 Safety and installation instructions
Please observe the prescribed safety instructions and stipulations from the
vehicle manufacturer and service workshops.
The manufacturer accepts no liability for damage in the following cases:
Faulty assembly or connection
Damage to the product resulting from mechanical influences and excess voltage
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in the operating manual
Please note the following:
To prevent the risk of short circuits, always disconnect the negative terminal of
the vehicle's electrical system before working on it.
If the vehicle has an additional battery, its negative terminal should also be dis-
connected.
Inadequate supply cable connections could result in short circuits, causing:
Cable fires
The airbag being triggered
Damage to electronic control equipment
Electrical malfunctions (indicators, brake light, horn, ignition, lights)
When working on the following cables, only use insulated cable terminals, plugs
and flat sockets:
30 (direct supply from positive battery terminal)
15 (connected positive terminal, behind the battery)
31 (return cable from the battery, earth)
58 (reversing light)
Do not use porcelain wire connectors.
Use a crimping tool to connect the cables.
Screw the cable when connecting cable 31 (earth)
Screw on the cable using a cable terminal and serrated washer to one of the
vehicle's earth bolts or
Screw the cable to the bodywork using a cable terminal and a self-tapping
screw
Make sure there is a good earth connection.
CAM35-IO-16s.book Seite 10 Dienstag, 21. Februar 2017 5:31 17
EN
CAM35 Safety and installation instructions
11
If you disconnect the negative terminal of the battery, all data stored in the volatile
memories will be lost.
The following data must be reset, depending on the vehicle equipment options:
–Radio code
Vehicle clock
–Timer
On-board computer
Seat position
You can find instructions for making these settings in the operating manual.
Observe the following installation instructions:
Secure the parts of the camera which are installed in the vehicle in such a way that
they cannot become loose under any circumstances (sudden braking, accidents)
and cause injuries to the occupants of the vehicle.
Secure any parts of the system concealed by the bodywork in such a manner that
they cannot be come loose or damage other parts or cables, or impair vehicle
functions (steering, pedals, etc).
To prevent damage when drilling, make sure there is sufficient space on the other
side for the drill head to emerge.
Deburr all drill holes and treat them with a rust-protection agent.
Always follow the safety instructions of the vehicle manufacturer.
Some work (e.g. on retention systems such as the AIRBAG etc.) may only be per-
formed by qualified specialists.
Observe the following instructions when working with electrical parts:
When testing the voltage in electrical cables, only use a diode test lamp or a volt-
meter.
Test lamps with a bulb consume too much voltage, which can damage the vehi-
cle's electronic system.
When making electrical connections, ensure that:
they are not kinked or twisted
they do not rub on edges
they are not laid in sharp-edged ducts without protection (fig. 1, page 3).
Insulate all connections.
Secure the cables against mechanical wear by using cable binders or insulating
tape, for example on existing cables.
CAM35-IO-16s.book Seite 11 Dienstag, 21. Februar 2017 5:31 17
EN
Scope of delivery CAM35
12
The camera is watertight. However, the seals on the camera cannot withstand a high-
pressure cleaner (fig. 2, page 3). Therefore, you should observe the following
instructions when handling the camera:
People (including children) whose physical, sensory or mental capacities or
whose lack of experience or knowledge prevent them from using this product
safely should not use it without the supervision or instruction of a responsible
person.
Do not open the camera, as this impairs the leak tightness and the function of the
camera (fig. 3, page 3).
Do not pull at the cables, as this impairs the tightness and the function of the cam-
era (fig. 4, page 3).
The camera is not suitable for use under water (fig. 5, page 3)!
3Scope of delivery
No. in
fig. 6, page 4
Quantity Description Ref. no.
1 1 Camera CAM35
CAM35 REAR
CAM35 REAR NAV
CAM35 TWIN
CAM35 TWIN NAV
9102000134
9102000133
9102000132
9102000131
2 1 Seal
3 1 CAM35 Y adapter CAM 9600000552
4 1 CAM35 Y adapter MON 9600000553
5 1 System cable 9600000137
1 NAV adapter (only CAM35 REAR NAV
or CAM35 TWIN NAV)
9600000558
2 Fastening bolts 6 x 25 mm
Installation and operating manual
CAM35-IO-16s.book Seite 12 Dienstag, 21. Februar 2017 5:31 17
EN
CAM35 Intended use
13
4 Intended use
The double camera CAM35 is primarily intended for use in the vehicles Fiat Ducato,
Citroën Jumper, Peugeot Boxer starting from model year 2006 with single roof. The
camera console is mounted between the bodywork and the brake light. It can be
used in video systems to observe the space around the vehicle from the driver's seat
when manoeuvring or parking, for example.
!
5 Technical description
The reversing camera and the long-distance camera (only CAM35 TWIN) are
housed in one console for the original brake light. The camera image is transferred
to a monitor via a system cable. The CAM35 is also suitable for connection to the
original Fiat navigation system Uconect, as the cameras provide an NTSC video
signal.
The camera consists of the following elements:
Only for CAM35 TWIN
In the CAM35 TWIN, a monitor with two video inputs must be connected that can
be switched between the image of the reversing and the long-distance cameras.
The long-distance camera transmits the image as if you were looking in the rear view
mirror.
WARNING!
Danger of personal injury by vehicle.
Reversing video systems are designed merely as an additional aid for
reversing, however this does not relieve you of the duty to take
proper care when reversing.
No. in
fig. 8, page 5
Description
1 Reversing camera
2 Long-distance camera (only CAM35 TWIN)
3 6-pin connection cable for long-distance camera (only CAM35 TWIN)
4 6-pin connection cable for reversing camera
CAM35-IO-16s.book Seite 13 Dienstag, 21. Februar 2017 5:31 17
EN
Fitting the camera CAM35
14
Only for CAM35 NAV
The cameras CAM35REAR NAV and CAM35 TWIN NAV can be connected to
monitors from other manufacturers. A universal adapter is included (CAM35 NAV
adapter).
6 Fitting the camera
6.1 Dismantling the brake light
Remove the two screws of the brake light (fig. 9, page 5).
Remove the plug of the brake light (fig. 0, page 6).
6.2 Laying cables
A
Therefore, please observe the following instructions:
As far as possible, use original ducts for laying the cables, or other suitable
options such as panelling edges, ventilation grilles or dummy plugs. If no open-
ings are available, you must drill holes for the cables. Check beforehand that
there is sufficient space on the other side for the drill head to emerge.
Wherever possible, lay cables inside the vehicle, as they are better protected
there than outside.
If you do need to lay a cable outside the vehicle, ensure that it is well fastened (use
additional cable ties, insulating tape etc.).
NOTICE! Beware of damage.
When drilling holes, check beforehand that there is sufficient space
on the other side for the drill head to come out.
Cables and connections that are not properly installed will cause
malfunctions or damage to components. Correct installation of
cables and connections ensures lasting and trouble-free operation of
the retrofitted components.
The cables may not be exposed for long periods to solvents such as
benzene, since solvents can damage the cable.
CAM35-IO-16s.book Seite 14 Dienstag, 21. Februar 2017 5:31 17
EN
CAM35 Fitting the camera
15
To prevent damage to the cables when laying them, ensure that they are far
enough away from hot or moving vehicle components (exhaust pipes, drive
shafts, light systems, fans, heaters, etc.). Use corrugated piping or other protec-
tive materials to protect against mechanical wear.
Screw on the plug connections for the connecting cables to protect them against
water penetration (fig. d, page 7).
When laying the cables, make sure:
they are not kinked or twisted
they do not rub on edges
they are not laid in sharp-edged ducts without protection.
Attach the cables securely in the vehicles to prevent tripping hazards. This can be
performed by using cable binders, insulating tape or gluing in place with adhe-
sives.
Lay the system cable.
6.3 Establishing the electrical connection for the camera
I
Guide the connector of the brake light through the console.
Re-attach the plug (fig. a 1, page 6) of the brake light onto the brake light.
Connect the camera as shown in fig. b, page 7 to fig. d, page 7.
NOTE
Lay the camera cable so that, should you need to remove the cam-
era, you can access the plug connection between the camera and
the extension cable easily. This greatly facilitates the disassembly.
To minimise corrosion in the plug, apply a small amount of grease,
such as pin grease, in one of the plugs.
CAM35-IO-16s.book Seite 15 Dienstag, 21. Februar 2017 5:31 17
EN
Fitting the camera CAM35
16
Legend to fig. b, page 7 and fig. c, page 7:
6.4 Fitting the camera
A
Proceed as follows (fig. e, page 8):
Secure the brake light and the console with two 6 x 25 mm fastening screws.
No. Description
1 6-pin connection cable for reversing camera
2 Y-adapter camera
3 Monitor
4 Y-adapter monitor
5System cable
6 6-pin connection cable for long-distance camera (only CAM35 TWIN)
7 NAV adapter (only CAM35 NAV)
ws white, video signal 1
ge yellow, video signal 2
sw black
rt red
NOTICE!
Make sure to guide the camera cables in the console bottom up to the
notches so that the cables are not pinched.
CAM35-IO-16s.book Seite 16 Dienstag, 21. Februar 2017 5:31 17
EN
CAM35 Cleaning and caring for the camera
17
7 Cleaning and caring for the camera
A
Clean the camera with a soft, damp cloth from time to time.
8Warranty
The statutory warranty period applies. If the product is defective, please contact the
manufacturer's branch in your country (see the back of the instruction manual for the
addresses) or your retailer.
For repair and guarantee processing, please send the following items:
Defect components
A copy of the receipt with purchasing date
A reason for the claim or description of the fault
9Disposal
Place the packaging material in the appropriate recycling waste bins wherever
possible.
M
If you wish to finally dispose of the product, ask your local recycling centre
or specialist dealer for details about how to do this in accordance with the
applicable disposal regulations.
NOTICE! Beware of damage.
Do not use any sharp or hard objects for cleaning since they may dam-
age the device.
CAM35-IO-16s.book Seite 17 Dienstag, 21. Februar 2017 5:31 17
EN
Technical data CAM35
18
10 Technical data
PerfectView
CAM35 REAR
PerfectView
CAM35 REAR NAV
Ref. no.: 9102000134 9102000133
Image sensor: 1/4" CMOS
Pixels: Approx. 345.000 pixels
Video standard: NTSC
Sensitivity: 1.5 lux
Viewing angle: Approx. 150°/60° diagonal
Operating voltage: 10 Vg to 16 Vg
Consumption: 1 W
Operating temperature: –30 °C to +70 °C
Protection class: IP69k
Vibration resistance: 10g
Dimensions W x H x D
(with bracket):
80 x 30 x 33 mm
Weight: Approx. 0.25 kg
CAM35-IO-16s.book Seite 18 Dienstag, 21. Februar 2017 5:31 17
EN
CAM35 Technical data
19
PerfectView
CAM35 TWIN
PerfectView
CAM35 TWIN NAV
Ref. no.: 9102000132 9102000131
Image sensor: 1/4" CMOS
Pixels: Approx. 345000 pixels
Video standard: NTSC
Sensitivity: 1.5 lux
Viewing angle: Approx. 150°/60° diagonal
Operating voltage: 10 Vg to 16 Vg
Consumption: 1 W
Operating temperature: –30 °C to +70 °C
Protection class: IP69k
Vibration resistance: 10g
Dimensions W x H x D
(with bracket):
80 x 30 x 33 mm
Weight: Approx. 0.25 kg
CAM35-IO-16s.book Seite 19 Dienstag, 21. Februar 2017 5:31 17
DE
Erklärung der Symbole CAM35
20
Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig
durch und bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe
des Produktes an den Nutzer weiter.
Inhaltsverzeichnis
1 Erklärung der Symbole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2 Sicherheits- und Einbauhinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6 Kamera montieren. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7 Kamera pflegen und reinigen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8 Gewährleistung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1 Erklärung der Symbole
!
A
I
WARNUNG!
Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer
Verletzung führen.
ACHTUNG!
Nichtbeachtung kann zu Materialschäden führen und die Funktion des
Produktes beeinträchtigen.
HINWEIS
Ergänzende Informationen zur Bedienung des Produktes.
CAM35-IO-16s.book Seite 20 Dienstag, 21. Februar 2017 5:31 17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184

Dometic CAM35 Mode d'emploi

Taper
Mode d'emploi
Ce manuel convient également à