Dometic CAM35 Mode d'emploi

CAM35

Rear View Video Camera

Installation and Operating Manual. . . . . . . . 9

Rückfahrvideokamera

Montage- und Bedienungsanleitung . . . . .20

Caméra vidéo de recul

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . . . 31

Cámara de vídeo de marcha atrás

Instrucciones de montaje y de uso . . . . . . .42

Câmara de marcha-atrás

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Videocamera per la retromarcia

Istruzioni di montaggio e d’uso . . . . . . . . .64

Achteruitrijvideocamera

Montagehandleiding en

gebruiksaanwijzing . . . . . . . . . . . . . . . . . . .75

Bakvideokamera

Monterings- og betjeningsvejledning . . . .86

Backningsvideokamera

Monterings- och bruksanvisning . . . . . . . . 97

Ryggevideokamera

Monterings- og bruksanvisning. . . . . . . . 107

Peruutusvideokamera

Asennus- ja käyttöohje . . . . . . . . . . . . . . . 118

Видеокамера заднего вида

Инструкция по монтажу

и эксплуатации . . . . . . . . . . . . . . . . . . . . . 128

Kamera cofania

Instrukcja montażu i obsługi. . . . . . . . . . . 140

Cúvacia kamera

Návod na montáž a uvedenie

do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 151

Couvací kamera

Návod k montáži a obsluze . . . . . . . . . . . 162

Tolatókamera

Szerelési és használati útmutató . . . . . . . 173

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

DRIVING SUPPORT

PERFECTVIEW

CAM35-IO-16s.book Seite 1 Dienstag, 21. Februar 2017 5:31 17

CAM35-IO-16s.book Seite 2 Dienstag, 21. Februar 2017 5:31 17

CAM35

3

1

2

3

4

5

CAM35-IO-16s.book Seite 3 Dienstag, 21. Februar 2017 5:31 17

CAM35

4

1

2

5

4

3

CAM35 REAR

6

1

2

5

4 3

CAM35 TWIN

7

CAM35-IO-16s.book Seite 4 Dienstag, 21. Februar 2017 5:31 17

CAM35

5

1

2

4

3

8

9

CAM35-IO-16s.book Seite 5 Dienstag, 21. Februar 2017 5:31 17

CAM35

6

0

1

a

CAM35-IO-16s.book Seite 6 Dienstag, 21. Februar 2017 5:31 17

CAM35

7

1 4

6

32

5

b

+12 Vg

ws

rtsw

ge

1

6

3

2

7

c

AB

d

CAM35-IO-16s.book Seite 7 Dienstag, 21. Februar 2017 5:31 17

CAM35

8

5 Nm

e

CAM35-IO-16s.book Seite 8 Dienstag, 21. Februar 2017 5:31 17

EN

CAM35 Explanation of symbols

9

Please read this instruction manual carefully before installation and first

use, and store it in a safe place. If you pass on the product to another

person, hand over this instruction manual along with it.

Table of contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

6 Fitting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

7 Cleaning and caring for the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

8 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

9 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

10 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

1 Explanation of symbols

!

A

I

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or

serious injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair

the function of the product.

NOTE

Supplementary information for operating the product.

CAM35-IO-16s.book Seite 9 Dienstag, 21. Februar 2017 5:31 17

EN

Safety and installation instructions CAM35

10

2 Safety and installation instructions

Please observe the prescribed safety instructions and stipulations from the

vehicle manufacturer and service workshops.

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

Please note the following:

• To prevent the risk of short circuits, always disconnect the negative terminal of

the vehicle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be dis-

connected.

• Inadequate supply cable connections could result in short circuits, causing:

– Cable fires

– The airbag being triggered

– Damage to electronic control equipment

– Electrical malfunctions (indicators, brake light, horn, ignition, lights)

• When working on the following cables, only use insulated cable terminals, plugs

and flat sockets:

– 30 (direct supply from positive battery terminal)

– 15 (connected positive terminal, behind the battery)

– 31 (return cable from the battery, earth)

– 58 (reversing light)

Do not use porcelain wire connectors.

• Use a crimping tool to connect the cables.

• Screw the cable when connecting cable 31 (earth)

– Screw on the cable using a cable terminal and serrated washer to one of the

vehicle's earth bolts or

– Screw the cable to the bodywork using a cable terminal and a self-tapping

screw

Make sure there is a good earth connection.

CAM35-IO-16s.book Seite 10 Dienstag, 21. Februar 2017 5:31 17

EN

CAM35 Safety and installation instructions

11

If you disconnect the negative terminal of the battery, all data stored in the volatile

memories will be lost.

• The following data must be reset, depending on the vehicle equipment options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the operating manual.

Observe the following installation instructions:

• Secure the parts of the camera which are installed in the vehicle in such a way that

they cannot become loose under any circumstances (sudden braking, accidents)

and cause injuries to the occupants of the vehicle.

• Secure any parts of the system concealed by the bodywork in such a manner that

they cannot be come loose or damage other parts or cables, or impair vehicle

functions (steering, pedals, etc).

• To prevent damage when drilling, make sure there is sufficient space on the other

side for the drill head to emerge.

• Deburr all drill holes and treat them with a rust-protection agent.

• Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may only be per-

formed by qualified specialists.

Observe the following instructions when working with electrical parts:

• When testing the voltage in electrical cables, only use a diode test lamp or a volt-

meter.

Test lamps with a bulb consume too much voltage, which can damage the vehi-

cle's electronic system.

• When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp-edged ducts without protection (fig. 1, page 3).

• Insulate all connections.

• Secure the cables against mechanical wear by using cable binders or insulating

tape, for example on existing cables.

CAM35-IO-16s.book Seite 11 Dienstag, 21. Februar 2017 5:31 17

EN

Scope of delivery CAM35

12

The camera is watertight. However, the seals on the camera cannot withstand a high-

pressure cleaner (fig. 2, page 3). Therefore, you should observe the following

instructions when handling the camera:

• People (including children) whose physical, sensory or mental capacities or

whose lack of experience or knowledge prevent them from using this product

safely should not use it without the supervision or instruction of a responsible

person.

• Do not open the camera, as this impairs the leak tightness and the function of the

camera (fig. 3, page 3).

• Do not pull at the cables, as this impairs the tightness and the function of the cam-

era (fig. 4, page 3).

• The camera is not suitable for use under water (fig. 5, page 3)!

3Scope of delivery

No. in

fig. 6, page 4

Quantity Description Ref. no.

1 1 Camera CAM35

CAM35 REAR

CAM35 REAR NAV

CAM35 TWIN

CAM35 TWIN NAV

9102000134

9102000133

9102000132

9102000131

2 1 Seal –

3 1 CAM35 Y adapter CAM 9600000552

4 1 CAM35 Y adapter MON 9600000553

5 1 System cable 9600000137

– 1 NAV adapter (only CAM35 REAR NAV

or CAM35 TWIN NAV)

9600000558

– 2 Fastening bolts 6 x 25 mm

– – Installation and operating manual

CAM35-IO-16s.book Seite 12 Dienstag, 21. Februar 2017 5:31 17

EN

CAM35 Intended use

13

4 Intended use

The double camera CAM35 is primarily intended for use in the vehicles Fiat Ducato,

Citroën Jumper, Peugeot Boxer starting from model year 2006 with single roof. The

camera console is mounted between the bodywork and the brake light. It can be

used in video systems to observe the space around the vehicle from the driver's seat

when manoeuvring or parking, for example.

!

5 Technical description

The reversing camera and the long-distance camera (only CAM35 TWIN) are

housed in one console for the original brake light. The camera image is transferred

to a monitor via a system cable. The CAM35 is also suitable for connection to the

original Fiat navigation system Uconect, as the cameras provide an NTSC video

signal.

The camera consists of the following elements:

Only for CAM35 TWIN

In the CAM35 TWIN, a monitor with two video inputs must be connected that can

be switched between the image of the reversing and the long-distance cameras.

The long-distance camera transmits the image as if you were looking in the rear view

mirror.

WARNING!

Danger of personal injury by vehicle.

Reversing video systems are designed merely as an additional aid for

reversing, however this does not relieve you of the duty to take

proper care when reversing.

No. in

fig. 8, page 5

Description

1 Reversing camera

2 Long-distance camera (only CAM35 TWIN)

3 6-pin connection cable for long-distance camera (only CAM35 TWIN)

4 6-pin connection cable for reversing camera

CAM35-IO-16s.book Seite 13 Dienstag, 21. Februar 2017 5:31 17

EN

Fitting the camera CAM35

14

Only for CAM35 NAV

The cameras CAM35REAR NAV and CAM35 TWIN NAV can be connected to

monitors from other manufacturers. A universal adapter is included (CAM35 NAV

adapter).

6 Fitting the camera

6.1 Dismantling the brake light

➤ Remove the two screws of the brake light (fig. 9, page 5).

➤ Remove the plug of the brake light (fig. 0, page 6).

6.2 Laying cables

A

Therefore, please observe the following instructions:

• As far as possible, use original ducts for laying the cables, or other suitable

options such as panelling edges, ventilation grilles or dummy plugs. If no open-

ings are available, you must drill holes for the cables. Check beforehand that

there is sufficient space on the other side for the drill head to emerge.

• Wherever possible, lay cables inside the vehicle, as they are better protected

there than outside.

If you do need to lay a cable outside the vehicle, ensure that it is well fastened (use

additional cable ties, insulating tape etc.).

NOTICE! Beware of damage.

• When drilling holes, check beforehand that there is sufficient space

on the other side for the drill head to come out.

• Cables and connections that are not properly installed will cause

malfunctions or damage to components. Correct installation of

cables and connections ensures lasting and trouble-free operation of

the retrofitted components.

• The cables may not be exposed for long periods to solvents such as

benzene, since solvents can damage the cable.

CAM35-IO-16s.book Seite 14 Dienstag, 21. Februar 2017 5:31 17

EN

CAM35 Fitting the camera

15

• To prevent damage to the cables when laying them, ensure that they are far

enough away from hot or moving vehicle components (exhaust pipes, drive

shafts, light systems, fans, heaters, etc.). Use corrugated piping or other protec-

tive materials to protect against mechanical wear.

• Screw on the plug connections for the connecting cables to protect them against

water penetration (fig. d, page 7).

• When laying the cables, make sure:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp-edged ducts without protection.

• Attach the cables securely in the vehicles to prevent tripping hazards. This can be

performed by using cable binders, insulating tape or gluing in place with adhe-

sives.

➤ Lay the system cable.

6.3 Establishing the electrical connection for the camera

I

➤ Guide the connector of the brake light through the console.

➤ Re-attach the plug (fig. a 1, page 6) of the brake light onto the brake light.

➤ Connect the camera as shown in fig. b, page 7 to fig. d, page 7.

NOTE

• Lay the camera cable so that, should you need to remove the cam-

era, you can access the plug connection between the camera and

the extension cable easily. This greatly facilitates the disassembly.

• To minimise corrosion in the plug, apply a small amount of grease,

such as pin grease, in one of the plugs.

CAM35-IO-16s.book Seite 15 Dienstag, 21. Februar 2017 5:31 17

EN

Fitting the camera CAM35

16

Legend to fig. b, page 7 and fig. c, page 7:

6.4 Fitting the camera

A

Proceed as follows (fig. e, page 8):

➤ Secure the brake light and the console with two 6 x 25 mm fastening screws.

No. Description

1 6-pin connection cable for reversing camera

2 Y-adapter camera

3 Monitor

4 Y-adapter monitor

5System cable

6 6-pin connection cable for long-distance camera (only CAM35 TWIN)

7 NAV adapter (only CAM35 NAV)

ws white, video signal 1

ge yellow, video signal 2

sw black

rt red

NOTICE!

Make sure to guide the camera cables in the console bottom up to the

notches so that the cables are not pinched.

CAM35-IO-16s.book Seite 16 Dienstag, 21. Februar 2017 5:31 17

EN

CAM35 Cleaning and caring for the camera

17

7 Cleaning and caring for the camera

A

➤ Clean the camera with a soft, damp cloth from time to time.

8Warranty

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the

addresses) or your retailer.

For repair and guarantee processing, please send the following items:

• Defect components

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

9Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever

possible.

M

If you wish to finally dispose of the product, ask your local recycling centre

or specialist dealer for details about how to do this in accordance with the

applicable disposal regulations.

NOTICE! Beware of damage.

Do not use any sharp or hard objects for cleaning since they may dam-

age the device.

CAM35-IO-16s.book Seite 17 Dienstag, 21. Februar 2017 5:31 17

EN

Technical data CAM35

18

10 Technical data

PerfectView

CAM35 REAR

PerfectView

CAM35 REAR NAV

Ref. no.: 9102000134 9102000133

Image sensor: 1/4" CMOS

Pixels: Approx. 345.000 pixels

Video standard: NTSC

Sensitivity: 1.5 lux

Viewing angle: Approx. 150°/60° diagonal

Operating voltage: 10 Vg to 16 Vg

Consumption: 1 W

Operating temperature: –30 °C to +70 °C

Protection class: IP69k

Vibration resistance: 10g

Dimensions W x H x D

(with bracket):

80 x 30 x 33 mm

Weight: Approx. 0.25 kg

CAM35-IO-16s.book Seite 18 Dienstag, 21. Februar 2017 5:31 17

EN

CAM35 Technical data

19

PerfectView

CAM35 TWIN

PerfectView

CAM35 TWIN NAV

Ref. no.: 9102000132 9102000131

Image sensor: 1/4" CMOS

Pixels: Approx. 345000 pixels

Video standard: NTSC

Sensitivity: 1.5 lux

Viewing angle: Approx. 150°/60° diagonal

Operating voltage: 10 Vg to 16 Vg

Consumption: 1 W

Operating temperature: –30 °C to +70 °C

Protection class: IP69k

Vibration resistance: 10g

Dimensions W x H x D

(with bracket):

80 x 30 x 33 mm

Weight: Approx. 0.25 kg

CAM35-IO-16s.book Seite 19 Dienstag, 21. Februar 2017 5:31 17

DE

Erklärung der Symbole CAM35

20

Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig

durch und bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe

des Produktes an den Nutzer weiter.

Inhaltsverzeichnis

1 Erklärung der Symbole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2 Sicherheits- und Einbauhinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6 Kamera montieren. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7 Kamera pflegen und reinigen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

8 Gewährleistung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

10 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

1 Erklärung der Symbole

!

A

I

WARNUNG!

Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer

Verletzung führen.

ACHTUNG!

Nichtbeachtung kann zu Materialschäden führen und die Funktion des

Produktes beeinträchtigen.

HINWEIS

Ergänzende Informationen zur Bedienung des Produktes.

CAM35-IO-16s.book Seite 20 Dienstag, 21. Februar 2017 5:31 17

La page charge ...

Dometic CAM35 Mode d'emploi

Ce manuel convient également à

Dometic CAM35 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents