Sauder Carson Forge 414444 Mode d'emploi

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-23

Français pg 24-26

Español pg 27-29

Lot # 358576 01/08/14

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Lift-Top Co ee Table

Carson Forge Collection | 414444

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

It's addicting.

Table of Contents Assembly Tools Required

2-3

4

5-23

24-26

27-29

30

31

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

414444 www.sauder.com/servicesPage 2

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

A RIGHT END (1)

B LEFT END (1)

C UPRIGHT (1)

D TOP (1)

E BOTTOM (1)

F PANEL (2)

G SHELF (1)

H2 RIGHT FRONT/LEFT REAR LEG (2)

I2 LEFT FRONT/RIGHT REAR LEG (2)

J BRACE (1)

K PANEL MOLDING (2)

L UPPER END MOLDING (2)

M LOWER END MOLDING (2)

N CENTER SUPPORT (4)

Part Identiﬁ cation

Now you know

our ABCs.

414444www.sauder.com/services

Page 3

A

B

C

D

E

F

G

H2

I2

J

K

L

M

N

K

F

N

L

M

H2

I2

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

414444 www.sauder.com/servicesPage 4

BLACK 9/16" LARGE HEAD SCREW - 24

1S

CAM COVER - 16

12P

CAM DOWEL - 8

2F

HIDDEN CAM - 24

1F

CAM SCREW - 16

8F

METAL PIN - 2

1R

WASHER - 8

13M

NUT - 8

24M

BLACK 9/16" FLAT HEAD SCREW - 14

32S

BLACK 1-7/8" FLAT HEAD SCREW - 8

2S

TACK GLIDE - 4

13E

BUMPER - 6

2M

6E

FOOT BRACKET - 2

5E

CORNER

CAP - 2

FOOT - 4

10E

8E

CORNER ACCENT - 4

SUPPORT

BRACKET - 2

37G 23M

LIFT TABLE

MECHANISM SET - 1

BLACK 3/4" MACHINE SCREW - 4

92S

BLACK 1-1/4" MACHINE SCREW - 4

93S

SILVER 1/2" MACHINE SCREW - 4

38S

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty carton to

avoid scratching your unit or the ﬂ oor.

å

Push twenty-four HIDDEN CAMS (1F) into the ENDS (A and B),

BOTTOM (E), PANELS (F), and SHELF (G). Then, insert the metal

end of eight CAM DOWELS (2F) into the HIDDEN CAMS in the

BOTTOM (E) and SHELF (G).

414444www.sauder.com/services

Page 5

A

B

F

E

F

G

1F

Arrow

1F

2F

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Arrow

Do not tighten the HIDDEN CAMS in this step.

Insert CAM DOWELS

into these parts only.

Arrow

1F

(8 used)

(24 used)

Arrow

Hole

Step 2

å

Turn sixteen CAM SCREWS (8F) into the LEGS (H2 and I2).

414444 www.sauder.com/servicesPage 6

8F

I2

H2

I2

H2

8F

(16 used)

å

Fasten a CORNER ACCENT (8E) to each LEG (H2 and I2).

Use four SILVER 1/2" MACHINE SCREWS (38S).

Step 3

414444www.sauder.com/services

Page 7

I2

H2

I2

H2

8E

SILVER 1/2" MACHINE SCREW

(4 used in this step)

38S

Step 4

å

Fasten the REAR LEGS (H2 and I2) to the ENDS (A and B).

Tighten six HIDDEN CAMS.

414444 www.sauder.com/servicesPage 8

I2

H2

B

A

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

Angled edge

These edges

should be even.

These edges

should be even.

1

2

å

Carefully turn your ENDS (A and B) over.

å

Turn eight BLACK 9/16" FLAT HEAD SCREWS (32S) into the

ENDS (A and B) until the shoulders of the SCREWS rest on the

surfaces of the ENDS.

å

Slide the END MOLDINGS (L and M) onto the ENDS (A and B)

until they are against the LEGS (H2 and I2). Line up the grooves

in the MOLDINGS over the heads of the SCREWS in the ENDS.

Step 5

414444www.sauder.com/services

Page 9

B

A

H2

I2

M

L

Surface

without

HIDDEN CAMS

Surface without

HIDDEN CAMS

These edges

should be even.

Shoulder

Apply pressure with your hands

as you guide the MOLDINGS over

the SCREWS and onto the ENDS.

BLACK 9/16" FLAT HEAD SCREW

(8 used in this step)

32S

Step 6

å

Carefully turn your ENDS (A and B) over.

å

Fasten the remaining LEGS (H2 and I2) to the ENDS (A and B).

Tighten six HIDDEN CAMS.

414444 www.sauder.com/servicesPage 10

B

A

H2

I2

These edges

should be even.

These edges

should be even.

Angled edge

1

2

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

å

Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into the PANELS (F)

until the shoulders of the SCREWS rest on the surfaces of the PANELS.

å

Slide the PANEL MOLDINGS (K) onto the PANELS (F). Line up the grooves

in the MOLDINGS over the heads of the SCREWS in the PANELS.

å

Then, fasten the SHELF (G) to the PANELS (F). Use six BLACK 1-7/8" FLAT

HEAD SCREWS (2S).

Step 7

414444www.sauder.com/services

Page 11

F

K

Surface without

HIDDEN CAMS

Surface without

HIDDEN CAMS

F

G

Surface with

HIDDEN CAMS

Surface

with

HIDDEN

CAMS

Surface

without

HIDDEN

CAMS

Shoulder

Apply pressure with your hands

as you guide the MOLDINGS over

the SCREWS and onto the ENDS.

BLACK 9/16" FLAT HEAD SCREW

(8 used in this step)

32S

BLACK 1-7/8" FLAT HEAD SCREW

(6 used in this step)

2S

Finished edge

Unﬁ nished edge

Step 8

å

Fasten the PANELS (F) and SHELF (G) to the LEFT END (B)

and LEGS (H2 and I2). Tighten four HIDDEN CAMS.

414444 www.sauder.com/servicesPage 12

G

B

F

H2

I2

Surface

with

HIDDEN

CAMS

Surface

with

HIDDEN

CAMS

Start Tighten

Arrow

Minimum

190 degrees

Caution

Risk of damage or

injury. HIDDEN CAMS

must be completely

tightened. HIDDEN

CAMS that are not

completely tightened

may loosen, and parts

may separate. To

completely tighten:

Arrow

Maximum

210 degrees

å

Insert two METAL PINS (1R) into the larger holes in the UPRIGHT (C).

å

Insert the METAL PINS (1R) in the end of the UPRIGHT (C) into the

holes in the SHELF (G).

Step 9

414444www.sauder.com/services

Page 13

G

C

1R

Step 10

å

Fasten the BOTTOM (E) to the LEFT END (B). Tighten two

HIDDEN CAMS.

å

Fasten the BOTTOM (E) to the UPRIGHT (C). Use two

BLACK 1-7/8" FLAT HEAD SCREWS (2S).

414444 www.sauder.com/servicesPage 14

B

C

E

Surface

with

HIDDEN

CAMS

BLACK 1-7/8" FLAT HEAD SCREW

(2 used in this step)

2S

Arrow

Minimum

190 degrees

Maximum

210 degrees

å

Fasten the RIGHT END (A) and LEGS (H2 and I2) to the

BOTTOM (E), PANELS (F), and SHELF (G). Tighten six

HIDDEN CAMS.

Step 11

414444www.sauder.com/services

Page 15

E

G

F

A

I2

H2

Arrow

Minimum

190 degrees

Maximum

210 degrees

Step 12

å

Carefully turn your unit onto its top.

å

Insert four TACK GLIDES (13E) into the FEET (10E).

å

Then, push a FOOT (10E) over the bottom edge of each

LEG (H2 and I2).

414444 www.sauder.com/servicesPage 16

I2

H2

I2

H2

10E

13E

å

Fasten the FOOT BRACKETS (6E) to the BOTTOM (E). Use six BLACK

9/16" LARGE HEAD SCREWS (1S).

å

Slide the CENTER SUPPORTS (N) onto the FOOT BRACKETS (6E).

å

Firmly push the CORNER CAPS (5E) onto the CENTER SUPPORTS (N).

Step 13

414444www.sauder.com/services

Page 17

E

N

6E

5E

BLACK 9/16" LARGE HEAD SCREW

(6 used in this step)

1S

Step 14

å

Carefully stand your unit upright.

å

Push six BUMPERS (2M) into the PANELS (F) and LEGS (H2 and I2).

414444 www.sauder.com/servicesPage 18

2M

F

H2

I2

å

Fasten the LIFT TABLE MECHANISMS (23M) to the TOP (D).

Use six BLACK 9/16" LARGE HEAD SCREWS (1S).

å

NOTE: Be sure to position the LIFT TABLE MECHANISMS on

the TOP exactly as shown.

Step 15

414444www.sauder.com/services

Page 19

23M

D

BLACK 9/16" LARGE HEAD SCREW

(6 used in this step)

1S

The holes are closer to this edge.

Step 16

å

Fasten the SUPPORT BRACKETS (37G) to the LIFT

TABLE MECHANISMS (23M). Use four WASHERS (13M),

NUTS (24M), and BLACK 3/4" MACHINE SCREWS (92S).

414444 www.sauder.com/servicesPage 20

37G

13M

24M

37G

24M

13M

23M

D

BLACK 3/4" MACHINE SCREW

(4 used in this step)

92S

La page charge ...

Sauder Carson Forge 414444 Mode d'emploi

Sauder Carson Forge 414444 Mode d'emploi

dans d''autres langues

Documents connexes