Best CG304TS Guide d'installation

Gas Cooktop

Installation Guide

SPECIFICATIONS, INSTALLATION,

AND MORE

2 | Wolf Customer Care 800.222.7820

Gas Cooktop

Contents

3 Gas Cooktop

4 Speciﬁcations

10 Installation

14 Troubleshooting

Features and speciﬁcations are subject to change at any

time without notice. Visit wolfappliance.com/specs for the

most up-to-date information.

Important Note

To ensure this product is installed and operated as safely

and eciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or prod-

uct damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise speciﬁed.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

wolfappliance.com | 3

Rating plate location

RATING PLATE

Product Information

Important product information, including the model and

serial number, are listed on the product rating plate. The

rating plate is located on the bottom of the cooktop. Refer

to the illustration below.

If service is necessary, contact Wolf Factory Certiﬁed

Service with the model and serial number. For the name of

the nearest Wolf Factory Certiﬁed Service or for questions

regarding the installation, visit the Product Support section

of our website, wolfappliance.com, or call Wolf Customer

Care at 800-222-7820.

Gas Cooktop

4 | Wolf Customer Care 800.222.7820

Installation Requirements

A minimum 2" (51) is required from the bottom of the

cooktop to combustible materials. If the cooktop is

installed above an oven, a minimum of ⁄"

(6) is required

between the units.

The Contemporary gas cooktop can be mounted ﬂush

with the top of the countertop or as a standard installation

sitting on top of the countertop surface. If the cooktop is

to be mounted ﬂush with the countertop, a recessed area

surrounding the cooktop cutout must be provided. The

countertop must be able to withstand temperatures up to

300°F

(149°C).

IMPORTANT NOTE: For ﬂush installations, do not use the

cooktop as a template to create the countertop open-

ing. Use the countertop cutout template or speciﬁcations

provided. Failure to do so may cause damage.

Specifications

Electrical Requirements

Installation must comply with all applicable electrical codes.

Locate the electrical supply as shown in the illustrations

on the following pages. A separate circuit servicing only

this appliance is required. A ground fault circuit interrupter

(GFCI) is not recommended and may cause interruption of

operation.

ELECTRICAL REQUIREMENTS

Electrical Supply grounded, 120 VAC, 60 Hz

Service 15 amp dedicated circuit

Receptacle 3-prong grounding-type

Power Cord 6' (1.8 m)

wolfappliance.com | 5

Gas Supply

Installation must comply with local codes or, in the

absence of local codes, with the National Fuel Gas Code.

Locate the gas supply as shown in the illustrations on the

following pages.

The cooktop is equipped for use with natural or liquid

propane (LP) gas. The product rating plate has information

on the type of gas that should be used. For rating plate

location, refer to the illustration below. If this information

does not agree with the type of gas available, check with

the local gas supplier. The gas pressure regulator is built

into the unit.

GAS REQUIREMENTS

NATURAL GAS WC

Supply Pressure 5" (12.5 mb)

Min Line Pressure 7" (17.5 mb)

Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

LP GAS WC

Supply Pressure 10" (25 mb)

Min Line Pressure 11" (27.4 mb)

Max Regulator Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

The cooktop must be connected to a regulated gas supply.

The supply line must be equipped with an approved

external gas shut-o valve located near the cooktop in an

accessible location. Do not block access to the shut-o

valve. Refer to the illustration below.

A gas supply of ⁄"

(19) ID line must be provided to the

cooktop. If local codes permit, a certiﬁed, 3'

(.9 m) long,

⁄"

(13) or ⁄" (19) ID ﬂexible metal appliance connector is

recommended to connect the units ⁄" NPT male inlet to

the gas supply line. Pipe joint compounds, suitable for use

with natural or LP gas should be used.

The appliance and its shut-o valve must be disconnected

from the gas supply piping system during any pressure

testing of the system at test pressures in excess of .5 psi

(3.5 kPa). The appliance must be isolated from the gas

supply piping system by closing its individual manual shut-

o valve during any pressure testing of the system at test

pressures equal to or less than .5 psi

(3.5 kPa).

Wolf natural gas cooktops will function up to 10,250'

(3124 m) in altitude without adjustment and LP gas cook-

tops will function up to 8,600'

(2621 m). If the installation

exceeds these elevations, contact your authorized Wolf

dealer for a high altitude conversion kit.

SHUT-OFF VALV E

OPEN POSITION

GAS SUPPLYTO APPLIANCE

Gas shut-o valve

Rating plate location

RATING PLATE

Specifications

6 | Wolf Customer Care 800.222.7820

FRONT VIEW

SIDE

VIEW

COUNTERTOP CUTOUT

NO

TE: Shaded area above countertop indicates minimum clearance to combustible surfaces,

combus

tible materials cannot be located within this area.

13"

(330)

18"

(457)

7"

(178)

E G

30"

(762)

14"

(356)

19

1

/2"

(495)

2

1

/2" (64)

2

1

/2" (64)

15" Gas Cooktop

STANDARD INSTALLATION

Specifications

wolfappliance.com | 7

24", 30", and 36" Gas Cooktops—Transitional and Professional

STANDARD INSTALLATION

10"

(254)

4" (102)

3

1

/2" (89)

FRONT VIEW

SIDE

VIEW

COUNTERTOP CUTOUT

NO

TE: Shaded area above countertop indicates minimum clearance to combustible surfaces,

combus

tible materials cannot be located within this area.

El

ectrical and gas supply location only applies to installations with built-in oven.

30"

(762)

W

WIDTH

13"

(330)

18"

(457)

9"

(229)

19

1

/

2

"

(495)

2

1

/2" (64)

2

1

/

2

"

(64)

E G

CUTOUT WIDTH W

24" Cooktop* 23" (584)

30" Cooktop 29" (737)

36" Cooktop 35" (889)

*Transitional only.

Specifications

8 | Wolf Customer Care 800.222.7820

36" Gas Cooktop—Contemporary

STANDARD INSTALLATION

FRONT VIEW

SIDE

VIEW

NOTE:

Shaded area above countertop indicates minimum clearance to combustible surfaces,

combus

tible materials cannot be located within this area.

Ma

ximum facade thickness 1" (25). 1" (25) thickness extends 17 " (432) left and right and 2" (51) above and below centerlines.

30"

(762)

13"

(330)

18"

(457)

9"

(229)

E G

35" (889)

CUTOUT WIDTH

COUNTERTOP CUTOUT

20"

(508)

2

1

/2" (64)

5"

(127)

C

L

10"

(254)

1

/4" (32)

DIAMETER

4" (102)

C

L

3

7

/

8

"

(98) MIN

–5

1

/

8

"

(130) MAX

2" (51) MIN–

5"

(127) MAX

Specifications

wolfappliance.com | 9

36" Gas Cooktop—Contemporary

FLUSH INSTALLATION

FRONT VIEW

SIDE

VIEW

NOTE:

Shaded area above countertop indicates minimum clearance to combustible surfaces,

combus

tible materials cannot be located within this area.

Ma

ximum facade thickness 1" (25). 1" (25) thickness extends 17 " (432) left and right and 2" (51) above and below centerlines.

Outsid

e corner radius

3

/8" (10).

30"

(762)

13"

(330)

18"

(457)

9"

(229)

E G

36" (914) MIN

RECESS

21"

(533) MIN

RECESS

35"

(889)

CUTOUT WIDTH

COUNTERTOP CUTOUT

20"

(508)

2

1

/

2

"

(64)

5

/64"

(

2

)

COUNTERTOP

PROFILE

5"

(127)

C

L

10"

(254)

1

/4" (32)

DIAMETER

4"

(102)

C

L

3

7

/8" (98) MIN–5

1

/8" (130) MAX

2" (51) MIN–

5"

(127) MAX

Specifications

10 | Wolf Customer Care 800.222.7820

Transitional and Professional Cooktop

STANDARD INSTALLATION

1 Lower the cooktop into the countertop cutout. Center

the cooktop in the opening with the front edge aligned

parallel to the front edge of the countertop. Using a

pencil, outline the rear edge of the cooktop on the

countertop. Remove the cooktop.

2 Apply the foam strip to the perimeter of the countertop

opening. Refer to the illustration below. Do not seal the

cooktop to the countertop.

3 Insert the cooktop into the opening, aligning the rear

edge with the pencil line. Verify the cooktop is aligned

with the front edge of the countertop.

4 Attach the provided brackets to the bottom of the unit.

Insert the 3⁄"

(89) clamping screws into the brack-

ets. Use a screwdriver to tighten the clamping screws

against the bottom of the countertop. Do not over-

tighten screws. Refer to the illustration below.

Cooktop Installation

Remove the cooktop and components from the shipping

package and recycle packing materials.

Installation

FOAM STRIP

COUNTERTOP

BRACKET

CLAMPING

SCREW

Transitional and Professional

cooktop

wolfappliance.com | 11

Contemporary Cooktop

STANDARD INSTALLATION

An optional template has been provided to aid in place-

ment of the valve holes.

IMPORTANT NOTE: Prior to installing the cooktop, install

the valve stem spacers on the valve stem retainers to

achieve the appropriate depth. A 1"

(25) thick facade does

not require a spacer. For all facades less than 1"

(25), sub-

tract the thickness of the facade from 1"

(25) to determine

the required spacer thickness.

1 Once the proper spacing is determined, remove the

paper backing from the spacers and apply to each valve

stem. Refer to the illustration below.

2 Insert the front of the cooktop into the opening. Slightly

angle the cooktop to align each valve stem with the

holes in the façade. Then lower the back of the cook-

top into position. Refer to the illustration below.

3 Install the bezels to the valve assemblies by rotating

clockwise until hand tight. Do not overtighten. Refer to

the illustration.

SPACER

RETAINER

ALIGN

VALVE STEMS

Apply spacers prior to

installation

Insert Contemporary cooktop

BEZEL

Install bezels

Installation

12 | Wolf Customer Care 800.222.7820

1 Apply a thin ﬁlm of petroleum jelly to the outermost

underside edge of the cooktop pan. The petroleum jelly

aids in future removal.

2 Insert the cooktop into the opening.

3 Ensure the cooktop is fully seated and centered in the

opening.

4 Install the bezels to the valve assemblies by rotating

clockwise until hand tight. Do not overtighten. Refer to

the illustration below.

5 Apply the sealant between the cooktop and countertop.

6 Use the squeegee to smooth the seam and remove

excess sealant.

7 Allow the sealant to set for 20 minutes.

8 Use denatured alcohol and paper towels to clean the

seam.

9 Allow 24 hours for the sealant to cure.

10 Use a stainless steel cleaner/polish to remove sealant

from the countertop and cooktop.

Contemporary Cooktop

FLUSH INSTALLATION

The following are provided:

• A required installation kit.

• An optional template to aid in cooktop placement.

• An optional template to aid in valve hole placement.

IMPORTANT NOTE: Prior to installing the cooktop, install

the valve stem spacers on the valve stem retainers to

achieve the appropriate depth. A 1"

(25) thick facade does

not require a spacer. For all facades less than 1"

(25), sub-

tract the thickness of the facade from 1"

(25) to determine

the required spacer thickness.

1 Once the proper spacing is determined, remove the

paper backing from the spacers and apply to each valve

stem. Refer to the illustration below.

2 Clean all surfaces of dust and debris.

3 Insert the front of the cooktop into the opening. Slightly

angle the cooktop to align each valve stem with the

holes in the façade and lower the back of the cooktop

into position. Refer to the illustration below.

4 Verify there is a gap of at least ⁄" (2) to the countertop

around the perimeter of the cooktop. The gap allows

for heat expansion. The countertop may be damaged if

there is an insucient gap.

5 Remove the cooktop.

SPACER

RETAINER

ALIGN

VALVE STEMS

Apply spacers prior to

installation

Insert Contemporary cooktop

BEZEL

Install bezels

Installation

6

7

8

9

12

13

14

15

10

11

wolfappliance.com | 13

Gas Supply Connection

All connections to the gas piping must be wrench-tight-

ened. Do not overtighten or allow pipes to turn when

tightening.

If a ﬂexible metal connector is used, verify it is not kinked,

then attach the gas supply line to the regulator on the

cooktop. Open the valve and check for leaks by plac-

ing a liquid detergent solution onto all gas connections.

Bubbles around the connections indicate a gas leak. If a

leak appears, close the shut-o valve and adjust the con-

nections.

Burner Grates

24" COOKTOP

For the 24" cooktop, the grates must be positioned cor-

rectly to ensure proper burner performance. The grates

have an indicator on the bottom of the front edge. Position

the grates with the indicator toward the front of the cook-

top. Refer to the illustration below.

FRONT

Grate placement (24" cooktop)

Installation

14 | Wolf Customer Care 800.222.7820

Troubleshooting

IMPORTANT NOTE: If the cooktop does not operate prop-

erly, follow these troubleshooting steps:

• Verify electrical power is supplied to the cooktop.

• Verify the gas supply shut-o valve is in the open

position.

• If the cooktop does not operate properly, contact Wolf

Factory Certiﬁed Service. Do not attempt to repair the

cooktop. Wolf is not responsible for service required to

correct a faulty installation.

wolfappliance.com | 15

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowﬂake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &

Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.

All other trademarks are property of their respective owners in the United States and other countries.

2 | Atención al cliente de Wolf 800.222.7820

Estufa de gas

Contenido

3 Estufa de gas

4 Especiﬁcaciones

10 Instalación

14 Resolución de problemas

Las características y especiﬁcaciones están sujetas a cam-

bios sin previo aviso. Visite wolfappliance.com/specs para

obtener la información más actualizada.

Aviso importante

Para garantizar que este producto se instale y opere de

la forma más segura y eﬁciente posible, tome nota de los

siguientes tipos de información resaltada en esta guía:

AVISO IMPORTANTE señala la información que es espe-

cialmente importante.

PRECAUCIÓN indica una situación en la que se pueden

sufrir heridas leves o provocar daños al producto si no se

siguen las instrucciones.

ADVERTENCIA indica peligro de que se produzcan heridas

graves o incluso la muerte si no se siguen las precauciones.

AVISO IMPORTANTE: En toda esta guía, las dimensiones

entre paréntesis son milímetros, a menos que se espe-

ciﬁque lo contrario.

AVISO IMPORTANTE: Guarde estas instrucciones para el

inspector eléctrico local.

wolfappliance.com | 3

Información del producto

La información importante del producto, incluido el

modelo y número de serie de la unidad, se encuentra en la

placa de datos del producto. La placa de datos se localiza

en la parte baja de la estufa. Consulte la siguiente ilus-

tración.

Si necesita servicio, póngase en contacto con el centro

de servicio autorizado de Wolf y tenga a la mano el

modelo y número de serie de la unidad. Para obtener

los datos del centro de servicio autorizado de Wolf más

cercano o si tiene preguntas acerca de la instalación, visite

la sección de Soporte de productos de nuestro sitio web,

wolfappliance.com o llame a la línea de atención al cliente

de Wolf al 800-222-7820.

Ubicación de la placa de datos

PLACA DE DATOS

Estufa de gas

4 | Atención al cliente de Wolf 800.222.7820

Requisitos de instalación

Se requiere una distancia mínima de 2" (51) desde la parte

baja de la estufa hasta los materiales combustibles. Si se

va a instalar una estufa sobre un horno, se requiere un

mínimo de ⁄"

(6) entre las unidades.

El tope de cocina a gas contemporáneo puede montarse

al ras de la parte alta del mostrador o de manera estándar

asentada sobre la superﬁcie del mostrador. Si el tope de

cocina va a montarse empotrado, al ras del mostrador,

debe contarse con un hueco en un área alrededor del tope

de cocina. El mostrador debe soportar temperaturas hasta

de 149 °C

(300 °F).

AVISO IMPORTANTE: En las instalaciones al ras, no utilice

el tope de cocina como plantilla para señalar los oriﬁcios

del mostrador. Utilice la plantilla de recorte para el mostra-

dor o las especiﬁcaciones suministradas. De no hacerlo

puede ocasionar daños.

Especificaciones

Instalación eléctrica

La instalación debe tener una conexión a tierra de confor-

midad con los códigos locales o, en ausencia de códigos

locales, con el Código Nacional de Electricidad, ANSI/

NFPA 70.

Coloque el suministro eléctrico tal y como se muestra

en las ilustraciones de las páginas 6–9. Es necesario un

circuito independiente, que dé servicio únicamente a este

aparato. No es recomendable utilizar un circuito de fallos

de conexión a tierra (GFCI, por sus siglas en inglés) ya que

puede interrumpir el funcionamiento de la unidad.

REQUISITOS ELÉCTRICOS

Suministro eléctrico Con conexión a tierra, 120 V CA, 60 Hz

Servicio Circuito dedicado de 15 amperes

Receptáculo Conexión a tierra de 3 clavijas

Cable de alimentación eléctrica 6' (1.8 m)

wolfappliance.com | 5

Suministro de gas

La instalación debe cumplir con los códigos locales o, en

ausencia de códigos locales, con el Código Nacional de

Gas Combustible.

Coloque el suministro de gas tal y como se muestra en las

ilustraciones de las páginas 6–9.

La estufa está equipada para su uso con gas licuado (LP)

o propano natural. La placa de datos del producto con-

tiene información sobre el tipo de gas que se debe utilizar.

Para ubicar la placa de datos, consulte la siguiente ilus-

tración. Si esta información no coincide con el tipo de

gas disponible, consulte con el proveedor de gas local. El

regulador de presión de gas se encuentra interconstruido

dentro de la unidad.

REQUISITOS DEL SUMINISTRO DE GAS

GAS NATURAL WC

Presión del suministro de gas 5" (12.5 mb)

Presión mínima de la línea 7" (17.5 mb)

Presión máxima hacia el regulador 14" (34.9 mb), .5 psi (3.5 kPa)

GAS LP

WC

Presión del suministro de gas 10" (25 mb)

Presión mínima de la línea 11" (27.4 mb)

Presión máxima hacia el regulador 14" (34.9 mb), .5 psi (3.5 kPa)

La estufa debe conectarse a un suministro de gas regu-

lado. La línea del suministro debe estar equipada con una

llave de paso externa aprobada para gas ubicada cerca de

la estufa en un lugar accesible. No bloquee el acceso a la

llave de paso. Consulte la siguiente ilustración.

Se debe proporcionar una línea de suministro de gas de

⁄"

(19) de línea de diámetro interno para la estufa. Si el

código local lo permite, se recomienda utilizar un conec-

tor metálico ﬂexible certiﬁcado, de 3'

(.9 m) de largo, ⁄" (13)

o ⁄"

(19) de diámetro interior para conectar la entrada NPT

macho de ⁄" de la unidad a la línea de suministro de gas.

Debe utilizar compuestos para juntas de tubería aptos para

uso con gas natural o gas LP.

Debe desconectar el electrodoméstico y la llave de paso

del sistema de tuberías del suministro de gas durante cual-

quier prueba de presión del sistema a presiones de prueba

mayores a 5 psi

(3.5 kPa). Debe aislar el electrodoméstico

del sistema de tuberías del suministro de gas cerrando

manualmente la llave de paso durante cualquier prueba de

presión del sistema a presiones de prueba iguales o inferi-

ores a 0.5psi

(3.5 kPa).

Las estufas de gas natural de Wolf funcionarán hasta

10,250'

(3124 m) de altitud sin ajuste y las estufas de gas LP

funcionarán hasta 8,600'

(2621 m). Si la instalación supera

estas elevaciones, póngase en contacto con su distribuidor

autorizado de Wolf para conseguir un kit de conversión

para regiones altas.

LLAVE DE PASO EN

POSICIÓN ABIERTA

SUMINISTRO

DE GAS

A LA UNIDAD

Llave de paso del suministro

de gas

Ubicación de la placa de datos

PLACA DE DATOS

Especificaciones

6 | Atención al cliente de Wolf 800.222.7820

VISTA FRONTAL

VIST

A LATERAL

RECORTE DEL MOSTRADOR

NO

TA: la zona sombreada sobre el mostrador indica la distancia mínima a las superficies combustibles,

lo

s materiales combustibles no se pueden colocar en esta área.

13"

(330)

18"

(457)

7"

(178)

E G

30"

(762)

14"

(356)

19

1

/2"

(495)

2

1

/2" (64)

2

1

/2" (64)

Estufa de gas de 15"

INSTALACIÓN ESTÁNDAR

Especificaciones

La page charge ...

Best CG304TS Guide d'installation

Ce manuel convient également à

Best CG304TS Guide d'installation

dans d''autres langues

Autres documents