Faber NOPR30SSV Guide d'installation

NOPR30SS600

NOPR36SS600

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

Nova PRO

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU

START INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan

with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcient airisneededfor propercombustion andexhausting ofgases through

theue(chimney) offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbytheNational Fire ProtectionAssociation (NFPA),and theAmerican

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood and the

cooking surface or countertop. This hood has been approved by UL at this distance from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops and

combination ranges, a minimum of 30" is recommended and may be required.

The maximum depth of overhead cabinets is 13". Overhead cabinets on both sides of this unit must be

a minimum of 18" above the cooking surface or countertop. Consult the cooktop or range installation

instructions given by the manufacturer before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured

Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for

Mobile Home Construction and Safety, Title 24, HUD, Part 280). See Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a nonmetal-

lic thermal break should be installed to minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal break. The break should be as close

as possible to where the vent system enters the heated portion of the house.

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct

tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening around

the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbu-

lence that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts. Do

not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame

must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

4

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

5

RANGEHOOD DIMENSIONS

Min. 24" Min. 30"

6

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Lights, Filters, Blower.

2 1 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

3 1 Cover

10 1 Damper ø 5 7/8"

Ref. Qty. Installation Components

7.1 2 Hood Body Fixing Brackets

7.2.1 2 Upper Chimney Section Fixing

Brackets

12a 10 Screws 3/16" x 1 3/4"

12b 4 Screws 1/8" x 3/8"

12d 2 Screws 3/16" x 1"

12e 3 Screws 1/8" x 1/4"

Qty. Documentation

1 Instruction Manual

Available Accessories

Direct Connect Wiring Box sku # number: WIREBOX

Activated Charcoal Filter sku # FILTER1LL

High Ceiling Chimney Kit - Upper and Lower Chimney Flue to replace the original ue's

to t up to 11' ceilings - sku# HIGH3

sku# CFMRED2

Ductless Kit - Includes Ductless Diverter, Two Charcoal Filters - sku# DUCT5

Wireless Remote Control-REMCTRL

Parts needed

- 6" Round Metal ductwork .

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

1

2.2

2.1

10

7.2.1

12b

12a

12d



























 





























 



3

7

Choose your ducting method

Non Ducted - Recirculation OptionDucted Venting Options Installation

Requires

purchase of

Activated

Charcoal

Accessory

Horizontal

Vertical

6"







H

I



Install Damper that is included with the Hood

before connecting to the ductwork.

Only for Ducted Venting Installation























Remove the lters one at a time, supporting them

with one hand and turning the safety knobs (pull

and turn).

1

8

6"

Rear

Ducted Venting Options Installation

Ducting Methods

The Electrical Connector

must be removed rst

before converting the

hood to Rear Ducting

mode.























Rear Ducted Venting diagram

9

Disconnect the

Electrical Connectors

by depressing the tabs

with your hand and

also using light force on

one tab with a at head

screwdriver.

Remove the 2 screws

as shown in the image

to the left from the top

electrical cover and set

aside.

As shown in the image to the left

pull out the loose cable with the

electrical cover and set aside.

Caution: Do not damage

the Cable.

10

As shown in the image to the right use

a athead screwdriver to break out the

rear electrical knockout.





For a horizontal ducting

installation the motor

needs to be unsecured

by rst removing the 12

screws as shown.









Once the screws are removed,

extract the blower from the body

of the Hood and position it so the

transition opening is facing to the

rear wall (from the back remove and

rotate 180 degrees to the left, and

then ip it back 90 degrees as shown

in the diagram).

11





Once the blower is in place re-install the

12 screws to fasten the motor to the Hood

body.

Reconnect the

Connectors to the

blower.

Fix the Supplied Cover with

3 screws 12e.

As shown in the image to the right

take the cable and cover removed

previously and place back in original

position and secure with the 2 screws

removed previously.

Caution: Do not damage

the Cable.

12

2

3

´

>



























x8











x8

´



´

´

´

´ ´



7.2.1

Draw a vertical line on the supporting wall as high as practical, at the center of the area in which

the hood will be installed.

Draw a horizontal line at where the bottom edge of the hood will be located as indicated in the gure

that is a minimum of 24" electric and 30" gas cooking surface clearance.

Installation Instructions

Place a Upper bracket 7.2.1 on the wall as shown about 1 1/8" from the ceiling or upper limit, aligning the

centers(notch) with the vertical reference line and mark the wall at the centers of the holes in the bracket.

Place the other bracket 7.2.1 on the wall as shown, below the rst bracket, at the height of the upper

chimney section supplied and aligning the centers(notch) with the vertical line.

Mark the wall at the centers of the holes in the bracket.

Place bracket 7.1 as shown 5” 13/16 from the vertical reference line and 7” 1/2 above the horizontal

reference line.

Mark the centers of the holes in the bracket and repeat this operation on the other side.

Drill ø 5/16" holes at all the centers points marked (point 1,2,3,4,5,6,7,8) as shown.

Fix the 2 brackets 7.2.1 using the 12a screws supplied with wall plugs (purchase separately).

13

I = 6x

4

5

6

7

12a

x2

Ø

8

mm

x2

Installation screws provided must be secured

with wall plugs (purchase separately).

From inside the Hood body, mark the security

hole, drill ø 5/16" where marked, insert 2 wall

plugs 11 in the holes and x with 2 screws.

5/16"

Fix the brackets 7.1 using the 12a screws

supplied in the hood body xing holes as

shown.





Screw the two screws 12d supplied onto the

brackets 7.1.

Hook the hood body onto the bracket 7.1,

centering it around the vertical line.

Use the adjusting screws 12d underneath the

hood to level the hood body.

12a

14

2.1

2.2

8

10

11

9

Slightly widen

the two sides

of the upper

chimney and

hook them

behind the

brackets 7.2.1,

making sure

that they are

well seated.

Secure the sides to the brackets by using the 4

screws 12b.

13

Fix the bracket

7.2.1 using the

screws 12a

supplied.

12

Slightly widen the two

sides of the lower section

and hook them between

the upper section and the

wall, making sure that they

are properly housed.

Install Roof or Wall

Cap purchased

separately. Con-

nect the 6" metal

ductwork to the

Roof or Wall Cap

and then attach

ductwork.

Vertical or Horizontal

Ducting Installation

L = 4x

12a



N = 4x

12b

2.1

Fix the the

lower chim-

ney hood

laterally to

the hood

body.

15



14

Non-Ducted Recirculation Option

Only for the recirculation version, connect the hood

to the Air outlet.

16 17

2.1

Fix the Ductless Diverter with two screws 12a supplied

as shown.

Slightly widen

the two sides of

the upper chim-

ney and hook

them behind

the brackets

and connect to

the Ductless

Diverter, mak-

ing sure that

they are well

seated.

15



12a

Fix the lower Bracket 7.2.1 with two screws 12a

supplied as shown.

N = 4x

12b

Secure the sides to the brackets by using the 4

screws 12b.

2.2

2.1

18 19

Slightly widen the two

sides of the the lower

chimney hood and hook

them between

the upper section and the

wall, making sure that they

are properly housed.

Fix the the

lower chim-

ney hood

laterally to

the hood

body .

16

22

21

























Replace the metal grease lters

removed previously.

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

ELECTRICAL INSTALLATION WITH CONNECTION

CABLE

GROUNDING INSTRUCTIONS This appliance must

be grounded. In the event of an electrical short circuit,

grounding reduces the risk of electric shock by providing

an escape wire for the electric current. This appliance

is equipped with a cord having a grounding wire with a

grounding plug. The plug must be plugged into an outlet

that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of

electric shock.

Consult a qualied electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord

is too short, have a qualied electrician install an outlet

near the appliance.

ELECTRICAL INSTALLATION WITH

OPTIONAL WIRING BOX

For Permanent wiring Installation-Use only

with Listed rangehood Wiring Box kit

sku # WIREBOX, manufactured by Faber.

Max. 33 7/16”

For Non-Ducted Recirculation

Option

Required Activated Charcoal Filter

Accessory - sku # - FILTER1

(purchased separately)

Attach each

charcoal

lter to the

black grid on

each side of

the blower.

Press the

charcoal

lter tightly

to the black

grid on the blower side and rotate the lter

clockwise (towards the front of the hood) until it

locks into place. Turn counterclockwise (towards

the back of the hood) to remove.

20

17

USE AND CARE INFORMATION

T1. Fan Off Button:Turn the blower Off. The fan can be operated by pressing any of the fan setting

buttons.

Hold down this button for 2 seconds to activate Delay Off function which will keep the fan On for 15

minutes and automatically shut Off.

T2. Fan Settings Buttons: Low Speed.

T3. Fan Settings Buttons: Medium Speed.

T4. Fan Settings Buttons: High Speed / Intensive Speed.

Hold down the button for 2 seconds to activate the INTENSIVE SPEED, which is timed to run for 10

minutes. At the end of this time it will automatically return to the speed set before.Suitable to deal

with maximum levels of cooking fumes.

If you hold this button down for 2 seconds when the hood is off, then after 2 minutes the motor will

shut off.

L. Light Button: Press the LIGHT button to turn the light on and again to turn off.

T1 T2 T3 T4 L

LT1 T2 T3 T4

For Best Results

Start the rangehood several minutes before cooking to develop proper airow. Allow the

rangehood to operate for several minutes after cooking is complete to clear all smoke and

odors from the kitchen.

18

Cleaningmetalgreaselters

The lters must be cleaned every 2 months of operation,

or more frequently for particularly heavy usage, and

can be washed in a dishwasher.The metal grease lters

should be cleaned frequently in hot detergent solution or

washed in the dishwasher. Stainless steel cleaner should

be used on stainless rangehoods. Abrasives and scouring

agents can scratch stainless steel nishes and should not

be used to clean nished surface. Remove all water or

any other liquid from washing before re-installing lters.

• Remove the lters one at a time, supporting them

with one hand and turning the safety knobs (pull

and turn).

• Wash the lters, taking care not to bend them.

Allow them to dry before retting.

• Replace them and x them using the safety knobs

provided (pull and turn).

Replacing Activated Charcoal Filter

The Activated Charcoal Filters are not washable

and cannot be regenerated, and should be replaced

approximately every 4 months of operation, or more

frequently with heavy usage.

• Remove the charcoal lter by rotating it clockwise (

backwards) until it unlocks from the motor housing

and pull off sideways.

• To re-insert each charcoal lter, place up against the

side of the blower and push it inward. Then turn the

charcoal lter clockwise (forward) until it ts into place.

Lighting unit

• Remove the snap-on lamp cover by levering it from

under the metal ring, supporting it with one hand.

• Replace the lamp with a new one of the same type,

making sure that you insert the two pins properly into

the housings on the lamp holder.

• Replace the snap-on lamp cover.

"When used in recirculation mode, to Reduce the

Risk of Fire and Shock use only conversion kit

Model FILTER 1"

























19

Wiring Diagram

         

 







 















































































 























 















20

January 4, 2016

FABER CONSUMER WARRANTY & SERVICE

All Faber products are warranted against any defect in materials or workmanship for the original purchaser

for a period of 1 year from the date of original purchase (requires proof of purchase). This warranty covers

labor and replacement parts. Faber, at its option, may repair or replace the product or components

necessary to restore the product to good working condition. To obtain warranty service, contact the dealer

from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber

distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

The following is not covered by Faber's warranty:

1. Service calls to correct the installation of your range hood, to instruct you how to use your range hood, to

replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace range hood light bulbs, fuses or filters. Those consumable parts are

excluded from warranty coverage.

3. Repairs when your range hood is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes or Faber documentation, or use of products

not approved by Faber.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada, including

any non-UL or C-UL approved Faber range hoods.

6. Repairs to the hood resulting from unauthorized modifications made to the range hood.

7. Expenses for travel and transportation for product service in remote locations and pickup and delivery

charges. Faber range hoods should be serviced in the home.

THIS WARRANTY DOES NOT ALLOW RECOVERY OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, PERSONAL INJURY/WRONGFUL

DEATH OR LOST PROFITS FABER WARRANTY IS LIMITED TO THE ABOVE CONDITIONS AND TO THE WARRANTY PERIOD

SPECIFIED HEREIN AND IS EXCLUSIVE. EXCEPT AS EXPRESSLY SPECIFIED IN THIS AGREEMENT, FABER DISCLAIMS ALL

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

.

This warranty gives you specific legal rights that may vary from state to state.

Model#: ______________________________ Serial #: _____________________________

La page charge ...

Faber NOPR30SSV Guide d'installation

Ce manuel convient également à

Faber NOPR30SSV Guide d'installation

dans d''autres langues

Documents connexes

Autres documents