HP Photosmart C6200 All-in-One Printer series Mode d'emploi

HP Photosmart C6200 All-in-One series

Basics Guide

Guide d’utilisation

Hewlett-Packard Company notices

The information contained in this document is subject to change without notice.

as allowed under copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying

such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial

errors or omissions contained herein.

Windows, Windows 2000, and Windows XP are U.S. registered trademarks of Microsoft Corporation.

Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

Avis publiés par la société Hewlett-Packard

Les informations contenues dans ce document peuvent faire l'objet de modifications sans préavis.

dans les cas permis par la législation relative aux droits d'auteur. Les seules garanties relatives aux produits et services HP sont décrites dans les

déclarations de garantie expresse accompagnant lesdits produits et services. Aucun élément de ce document ne constitue une garantie

supplémentaire. Hewlett-Packard ne saurait être tenu pour responsable des erreurs ou omissions techniques ou rédactionnelles de ce document.

Windows, Windows 2000 et Windows XP sont des marques déposées de Microsoft Corporation aux Etats-Unis.

Windows Vista est une marque déposée ou une marque de Microsoft Corporation aux Etats-Unis et/ou dans d'autres pays.

Intel et Pentium sont des marques ou des marques déposées d'Intel Corporation ou de ses filiales aux Etats-Unis et dans d'autres pays.

HP Photosmart C6200

All-in-One series

Basics Guide

English

Contents

1 HP All-in-One overview

The HP All-in-One at a glance....................................................................................................5

Control panel features................................................................................................................6

Find more information.................................................................................................................7

2Network setup

Wired network setup...................................................................................................................9

Install the software for a network connection...........................................................................11

Connect to additional computers on a network........................................................................12

Change the HP All-in-One from a USB connection to a network connection...........................12

Manage your network settings..................................................................................................12

3 Use the HP All-in-One features

Load originals and load paper..................................................................................................15

Avoid paper jams......................................................................................................................18

View and select photos.............................................................................................................18

Scan an image..........................................................................................................................19

Make a copy.............................................................................................................................20

Replace the ink cartridges........................................................................................................20

Clean the HP All-in-One...........................................................................................................23

4 Troubleshooting and support

Uninstall and reinstall the software...........................................................................................25

Hardware setup troubleshooting...............................................................................................25

Network troubleshooting...........................................................................................................28

Clear paper jams......................................................................................................................29

Information on ink cartridges and the print head......................................................................30

Support process.......................................................................................................................31

5 Technical information

System requirements................................................................................................................32

Product specifications...............................................................................................................32

Ink cartridge yield.....................................................................................................................32

Regulatory notices....................................................................................................................33

Warranty...................................................................................................................................34

4 HP Photosmart C6200 All-in-One series

English

1 HP All-in-One overview

Use the HP All-in-One to quickly and easily accomplish tasks such as making a copy,

scanning documents, or printing photos. You can access many HP All-in-One functions

directly from the control panel, without turning on your computer.

NOTE: This guide introduces basic operations and troubleshooting, as well as

provides information for contacting HP support and ordering supplies.

The onscreen Help details the full range of features and functions, including use of

the HP Photosmart software that came with the HP All-in-One.

The HP All-in-One at a glance

Label Description

1 Color graphics display (also referred to as the

display)

2 Control panel

3 Output tray (currently shown in the up position)

4 Paper-width guide for the main input tray

5 Main input tray (also referred to as the input tray)

6 Paper tray extender (also referred to as the tray

extender)

7 Paper-width and paper-length guides for the

photo tray

8 Photo tray

9 Paper-length guide for the main input tray

10 Ink cartridge door

HP All-in-One overview 5

English

Label Description

11 Memory card slots

12 Glass

13 Lid backing

14 Ethernet port

15 USB port

16 Power connection

*

17 Two-sided printing accessory

* Use only with the power adapter supplied by HP.

Control panel features

The following diagram and related table provide a quick reference to the HP All-in-One

control panel features.

Label Icon Name and Description

1 Color graphics display (also referred to as the display): Displays menus, photos,

and messages. The display can be pulled up and angled for better viewing.

2 Attention light: Indicates a problem occurred. See the display for more information.

3 Back: Returns to the previous screen on the display.

4 Setup: Opens the Setup menu where you can generate reports, change device

settings, and perform maintenance functions.

5 Help: Opens the Help Menu menu on the display where you can select a topic to

learn more about it. From the idle state, pressing Help lists a menu of items for which

help is available. Depending on the topic you select, the topic will appear on your

display or on your computer screen. When viewing screens other than Idle, the

Help button provides context sensitive help.

Chapter 1

(continued)

6 HP Photosmart C6200 All-in-One series

English

Label Icon Name and Description

6 Cancel: Stops the current operation.

7 Photo Menu: Launches the Photosmart Express menu for printing, saving, editing,

and sharing photos.

8 Red Eye Removal: Turns the Red Eye Removal feature on or off. By default, this

feature is turned off. When the feature is turned on, the HP All-in-One automatically

corrects red eye coloring in the photo currently shown on the display.

9 Photo Reprints: Enables you to make a copy of an original photo placed on the

glass.

10 Print Photos: Depending on whether you access your photos from the View,

Print, or Create menu, the Print Photos button will display the Print Preview screen

or it will print any selected photo(s). If no photos are selected, a prompt appears

asking if you want to print all the photos on your card.

11 Scan Menu: Opens the Scan Menu where you can select a destination for your

scan.

12 Start Scan: Starts a scan.

13 Copy Menu: Opens the Copy Menu where you can select copy options, such as

number of copies, paper size, and paper type.

14 Start Copy Black: Starts a black-and-white copy.

15 Start Copy Color: Starts a color copy.

16 On: Turns the HP All-in-One on or off. When the HP All-in-One is off, a minimal

amount of power is still supplied to the device. You can further reduce power supply

by holding down the On button for 3 seconds. This will put the HP All-in-One in

Standby/Off state. To completely remove power, turn the HP All-in-One off, and then

unplug the power cord.

17 Zoom out - (magnifying glass icon): Zooms out to show more of a photo. If you press

this button when a photo is shown on the display at 100%, the Fit to Page feature is

applied to the photo automatically.

18 Zoom in + (magnifying glass icon): Zooms in to enlarge the image on the display.

You can also use this button together with the arrows on the directional pad to adjust

the crop box for printing.

19 OK: Selects a menu setting, value, or photo on the display.

20 Directional pad: Allows you to navigate through photos and menu options by

pressing the up, down, left, or right arrow buttons.

If you are zooming in on a photo, you can also use the arrow buttons to pan around

the photo and select a different area to print.

Find more information

A variety of resources, both printed and onscreen, provide information about setting up

and using the HP All-in-One.

(continued)

Find more information 7

English

• Setup Guide

The Setup Guide provides instructions for setting up the HP All-in-One and installing

software. Make sure you follow the steps in the Setup Guide in order.

If you have problems during setup, see Troubleshooting in the last section of the

Setup Guide, or see “

Troubleshooting and support” on page 25 in this guide.

• Onscreen Help

The onscreen Help provides detailed instructions on features of the HP All-in-One

that are not described in this Basics Guide, including features that are only available

using the software you installed with the HP All-in-One.

•

www.hp.com/support

If you have Internet access, you can get help and support from the HP Web site. This

Web site offers technical support, drivers, supplies, and ordering information.

Chapter 1

8 HP Photosmart C6200 All-in-One series

English

2 Network setup

This section describes how to connect the HP All-in-One to a network and how to view

and manage network settings.

If you want to: See this section:

Connect to a wired (Ethernet) network. “Wired network setup” on page 9

Install the HP All-in-One software for use in a

networked environment.

“Install the software for a network connection”

on page 11

Add connections to more computers on the

network.

“Connect to additional computers on a

network” on page 12

Change the HP All-in-One from a USB

connection to a network connection.

NOTE: Use the instructions in this section if

you first installed the HP All-in-One with a USB

connection, and you now want to change to an

Ethernet network connection.

“Change the HP All-in-One from a USB

connection to a network connection”

on page 12

View or change the network settings. “Manage your network settings” on page 12

Find troubleshooting information. “Network troubleshooting” on page 28

Wired network setup

This section describes how to connect the HP All-in-One to a router, switch, or hub using

an Ethernet cable and how to install the HP All-in-One software for a network connection.

This is known as a wired or Ethernet network.

To set up the HP All-in-One on a wired

network, you need to do the following:

See this section:

First, collect all of the required materials. “What you need for a wired network”

on page 10

Next, connect to a wired network. “Connect the HP All-in-One to the network”

on page 10

Finally, install the software. “Install the software for a network connection”

on page 11

Network setup 9

English

What you need for a wired network

Before you connect the HP All-in-One to a network, make sure you have all of the required

materials.

❑

A functional Ethernet network that includes a router, switch, or hub with an Ethernet

port.

❑

CAT-5 Ethernet cable.

Although standard Ethernet cables look similar to standard telephone cables, they

are not interchangeable. There is a different number of wires in each one, and each

has a different connector. An Ethernet cable connector (also called an RJ-45

connector) is wider and thicker and always has 8 contacts on the end. A phone

connector has between 2 and 6 contacts.

❑

A desktop computer or laptop with an Ethernet connection.

NOTE: The HP All-in-One supports both 10 Mbps and 100 Mbps Ethernet

networks. If you are purchasing, or have purchased, a network interface card

(NIC), make sure it can operate at either speed.

Connect the HP All-in-One to the network

To connect the HP All-in-One to the network, use the Ethernet port on the back of the

device.

To connect the HP All-in-One to the network

1. Remove the yellow plug from the back of the HP All-in-One.

2. Connect the Ethernet cable to the Ethernet port on the back of the HP All-in-One.

Chapter 2

10 HP Photosmart C6200 All-in-One series

English

3. Connect the other end of the Ethernet cable to an available port on your Ethernet

router, switch, or wireless router.

4. Once you have connected the HP All-in-One to the network, install the software as

described in “

Install the software for a network connection” on page 11.

Install the software for a network connection

Use this section to install the HP All-in-One software on a computer connected to a

network. Before you install the software, make sure you have connected the

HP All-in-One to a network.

NOTE: If your computer is configured to connect to a series of network drives, make

sure that your computer is currently connected to these drives before installing the

software. Otherwise, HP All-in-One installation software might try to use one of the

reserved drive letters, and you will not be able to access that network drive on your

computer.

NOTE: Installation time can range from 20 to 45 minutes depending on your

operating system, the amount of available space, and the processor speed of your

computer.

To install the Windows HP All-in-One software

1. Quit all applications running on your computer, including any virus detection software.

2. Insert the Windows CD that came with the HP All-in-One into the CD-ROM drive on

your computer and follow the onscreen instructions.

3. If a dialog box about firewalls appears, follow the instructions. If you see firewall pop-

up messages, you must always accept or allow the pop-up messages.

4. On the Connection Type screen, select Through the network, and then click

Next.

The Searching screen appears as the Setup program searches for the HP All-in-One

on the network.

Install the software for a network connection 11

English

5. On the Printer Found screen, verify that the printer description is correct.

If more than one printer is found on the network, the Printers Found screen appears.

Select the HP All-in-One you want to connect.

6. Follow the prompts to install the software.

When you have finished installing the software, the HP All-in-One is ready for use.

7. If you disabled any virus detection software on your computer, make sure to enable

it again.

8. To test your network connection, go to your computer and print a self-test report to

the HP All-in-One.

Connect to additional computers on a network

You can connect the HP All-in-One to more than one computer on a small network of

computers. If the HP All-in-One is already connected to a computer on a network, for

each additional computer you must install the HP All-in-One software. Once you have set

up the HP All-in-One on the network you will not need to configure it again when you add

additional computers.

Change the HP All-in-One from a USB connection to a

network connection

If you first install the HP All-in-One with a USB connection, you can later change to an

Ethernet network connection. If you already understand how to connect to a network, you

can use the general directions below.

To change a USB connection to a wired (Ethernet) connection

1. Unplug the USB connection from the back of the HP All-in-One.

2. Connect an Ethernet cable from the Ethernet port on the back of the HP All-in-One

to an available Ethernet port on the router or switch.

3. Install the software for a network connection, choose Add a Device, and then choose

Through the network.

4. When the installation is complete, open Printers and Faxes (or Printers) in the

Control Panel and delete the printers from the previous USB installation.

Manage your network settings

You can manage network settings for the HP All-in-One through the HP All-in-One control

panel. Additional advanced settings are available in the Embedded Web Server, a

configuration and status tool you access from your Web browser using an existing

network connection to the HP All-in-One.

Change basic network settings from the control panel

You can perform a variety of network management tasks from the control panel, such as

printing the network settings and restoring network defaults.

View and print network settings

You can display a summary of the network settings on the HP All-in-One control panel,

or you can print a more detailed configuration page. The network configuration page lists

all of the important network settings such as the IP address, link speed, DNS, and mDNS.

Chapter 2

12 HP Photosmart C6200 All-in-One series

English

1. On the control panel of the HP All-in-One, press Setup.

2. Press

until Network is highlighted, and then press OK.

The Network Menu appears.

3. Press

until View Network Settings is highlighted, and then press OK.

The View Network Settings Menu appears.

4. Do one of the following:

• To display wired network settings, press

until Display Wired Summary is

highlighted, and then press OK.

This displays a summary of the wired (Ethernet) network settings.

• To print the network configuration page, press

until Print Network

Configuration Page is highlighted, and then press OK.

This prints the network configuration page.

Restore network defaults

You can reset the network settings to what they were when you purchased the

HP All-in-One.

1. On the control panel of the HP All-in-One, press Setup.

2. Press

until Network is highlighted, and then press OK.

3. Press

until Restore Network Defaults is highlighted, and then press OK.

4. Press OK to confirm that you want to restore the network defaults.

Change advanced network settings from the control panel settings

The advanced network settings are provided for your convenience. However, unless you

are an advanced user, you should not change any of these settings.

Set link speed

You can change the speed at which data is transmitted over the network. The default is

Automatic.

1. Press Setup.

2. Press

until Network is highlighted, then press OK.

The Network Menu appears.

3. Press

until Advanced Setup is highlighted, and then press OK.

Press

until Set Link Speed is highlighted, and then press OK.

4. Press

to select the link speed that matches your network hardware, and then press

OK to confirm the setting.

• Automatic

• 10-Full

• 10-Half

• 100-Full

• 100-Half

Change IP settings

The default setting for the IP settings is Automatic, which sets the IP settings

automatically. However, if you are an advanced user, you might want to manually change

the IP address, subnet mask, or the default gateway. To see the IP address and subnet

mask of the HP All-in-One, print a network configuration page from the HP All-in-One.

Manage your network settings 13

English

NOTE: When manually entering an IP setting, you must already be connected to an

active network, otherwise the setting will not stay when you exit from the menu.

CAUTION: Be careful when manually assigning an IP address. If you enter an invalid

IP address during the installation, your network components will not be able to connect

with the HP All-in-One.

1. Press Setup.

2. Press

until Network is highlighted, then press OK.

The Network Menu appears.

3. Press

until Advanced Setup is highlighted, and then press OK.

4. Press

until IP Settings is highlighted, and then press OK.

If the HP All-in-One is already connected to a wired network, you are prompted to

confirm that you want to change the IP settings. Press OK.

5. Press

until Manual is highlighted, and then press OK.

6. Press

to highlight one of the following IP settings, and then press OK.

• IP Address

• Subnet Mask

• Default Gateway

7. Enter your changes, and then press OK to confirm the setting.

Chapter 2

14 HP Photosmart C6200 All-in-One series

English

3 Use the HP All-in-One features

This chapter includes information about how to use the HP All-in-One for basic

operations. In addition, it provides instructions about how to load paper and replace the

ink cartridges.

Load originals and load paper

You can load many different types and sizes of paper in the HP All-in-One, including letter

or A4 paper, legal paper, photo paper, transparencies, envelopes, and HP CD/DVD tattoo

labels. By default, the HP All-in-One is set to detect the size and type of paper you load

in the input tray automatically and then adjust its settings to generate the highest quality

output for that paper.

If you are using special papers, such as photo paper, transparency film, envelopes, or

labels, or if you experience poor print quality using the automatically-adjusted settings,

you can manually set the paper size and type for print and copy jobs.

Load an original on the glass

You can copy or scan up to letter- or A4-size originals by loading them on the glass.

To load an original on the scanner glass

1. Lift the lid on the HP All-in-One.

2. Load your original print side down on the right front corner of the glass.

TIP: For more help on loading an original, refer to the engraved guides along the

edge of the glass.

3. Close the lid.

Load full-size paper

You can load many types of letter, A4, or legal paper into the main input tray of the

HP All-in-One.

Use the HP All-in-One features 15

English

To load full-size paper

1. Pull out the main input tray, and then slide the paper-width and paper-length guides

to their outermost positions.

2. Tap a stack of paper on a flat surface to align the edges, and then check the paper

for the following:

• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.

• Make sure all the paper in the stack is the same size and type.

3. Insert the stack of paper into the main input tray with the short edge forward and the

print side down. Slide the stack of paper forward until it stops.

TIP: If you are using letterhead, insert the top of the page first with the print side

down. For more help on loading full-size paper and letterhead, refer to the diagram

engraved in the base of the input tray.

4. Slide the paper-width and paper-length guides inward until they stop at the edges of

the paper.

Do not overload the main input tray; make sure the stack of paper fits within the input

tray and is no higher than the top of the paper-width guide.

Chapter 3

16 HP Photosmart C6200 All-in-One series

English

5. Push the main input tray back into the HP All-in-One.

6. Pull the output tray extender toward you, as far as it will go. Flip the paper catch at

the end of the output tray extender to open the extender the rest of the way.

NOTE: When you use legal-size paper, leave the tray extender closed.

Load 10 x 15 cm (4 x 6 inch) photo paper

You can load up to 10 x 15 cm (4 x 6 inch) photo paper into the photo tray of the

HP All-in-One. For the best results, use 10 x 15 cm (4 x 6 inch) HP Premium Plus Photo

Paper or HP Premium Photo Paper.

To load 10 x 15 cm (4 x 6 inch) photo paper in the photo tray

1. Raise the output tray, and then pull out the photo tray.

NOTE: You can also remove the entire photo tray assembly to load photo paper

into the photo tray.

2. Insert the stack of photo paper into the photo tray with the short edge forward and the

print side down. Slide the stack of photo paper forward until it stops.

If the photo paper you are using has perforated tabs, load the photo paper so that the

tabs are closest to you.

3. Slide the paper-length and paper-width guides inward against the stack of photo

paper until the guides stop.

Do not overload the photo tray; make sure the stack of photo paper fits within the

photo tray and is no higher than the top of the paper-width guide.

Load originals and load paper 17

English

4. Push in the photo tray, and then lower the output tray.

Avoid paper jams

To help avoid paper jams, follow these guidelines.

• Remove printed papers from the output tray frequently.

• Prevent curled or wrinkled paper by storing all unused paper flat in a resealable bag.

• Ensure that paper loaded in the input tray lays flat and the edges are not bent or torn.

• If you are printing labels, ensure that the label sheets are no more than two years old.

Labels on older sheets might peel off when the paper is pulled through the

HP All-in-One, and cause paper jams.

• Do not combine different paper types and paper sizes in the input tray; the entire stack

of paper in the input tray must be the same size and type.

• Adjust the paper-width guide in the input tray to fit snugly against all paper. Make sure

the paper-width guide does not bend the paper in the input tray.

• Do not force paper too far forward in the input tray.

• Use paper types that are recommended for the HP All-in-One.

View and select photos

You can view and select photos on your memory card before or while printing them.

1 CompactFlash (CF) types I and II

2 Secure Digital (SD), Secure Digital Mini (adapter required), Secure Digital High Capacity

(SDHC), MultiMediaCard (MMC), MMC Plus, MMC Mobile (RS-MMC; adapter required),

TransFlash MicroSD Card, or Secure MultiMedia Card

3 Memory Stick, Memory Stick Pro, Memory Stick Select, Memory Stick Magic Gate, Memory

Stick Duo or Duo Pro (adapter optional), or Memory Stick Micro (adapter required)

Chapter 3

18 HP Photosmart C6200 All-in-One series

English

4 xD-Picture Card

To view, select, and print photos

1. Insert a memory card into the appropriate slot on the HP All-in-One.

The Photosmart Express appears with the most recent photo shown on the display.

2. Load up to 10 x 15 cm (4 x 6 inch) photo paper in the photo tray or full-size photo

paper in the main input tray.

3. Press

until View is highlighted, and then press OK.

The View Photos screen appears.

4. Press

or to scroll through the thumbnails of your photos.

5. When the thumbnail of the photo you want to view is highlighted, press OK.

6. When the photo appears by itself on the display, press OK again.

The Photo Options screen appears.

7. With Print Preview highlighted, press OK.

The Print Preview screen appears, showing how your photo will look when printed.

8. If you want to select additional photos to view and print, press

to highlight Add

More, press OK, and repeat steps 4-6.

Or, once you're in the Add Photos screen, the quickest way to select multiple photos

(if you don't need the option to edit them) is to press

to select a photo, and then

press

or to scroll through more photos to select.

9. (Optional) If you want to check and/or modify any of your print settings, press

to

highlight Settings, and then press OK.

10. To print the photo(s), use

or to highlight Print Now (or press the Print Photos

button on the control panel).

A print status screen displays the number of pages to print and the estimated time to

complete.

Scan an image

You can start a scan from your computer or from the control panel of the HP All-in-One.

This section explains how to scan from the control panel of the HP All-in-One only.

NOTE: You can also use the software you installed with the HP All-in-One to scan

images. Using this software, you can edit a scanned image and create special projects

using a scanned image.

Scan an original to a computer

You can scan originals placed on the glass by using the control panel.

To scan to a computer

1. Load your original print side down on the right front corner of the glass.

2. Press Scan Menu.

3. Press

to highlight Scan to Computer, and then press OK.

Scan an image 19

English

4. If the HP All-in-One is connected to one or more computers on a network, do the

following:

a.Press OK to select Select Computer.

A list of the computers connected to the HP All-in-One appears on the display.

NOTE: The Select Computer menu might list computers with a USB

connection in addition to those connected through the network.

b.Press OK to select the default computer, or press to select a different computer,

and then press OK.

The Scan To menu appears on the display, listing the applications on the selected

computer.

If the HP All-in-One is connected directly to a computer with a USB cable, proceed

to step 5.

5. Press OK to select the default application to receive the scan, or press

to select a

different application, and then press OK.

A preview image of the scan appears on your computer, where you can edit it.

6. Make any edits to the preview image, and then click Accept when you are finished.

Scan an original to a memory card

You can send the scanned image as a JPEG image to the memory card that is currently

inserted. This enables you to use the photo print options to print borderless prints and

album pages from the scanned image.

NOTE: If the HP All-in-One is connected to a network, you can access the scanned

image only if the memory card is being shared across the network.

To save a scan to a memory card

1. Make sure your memory card is inserted into the appropriate slot on the HP All-in-One.

2. Load your original print side down on the right front corner of the glass.

3. Press Scan Menu on the control panel.

4. Press

to highlight Scan to Memory Card, and then press OK.

NOTE: Alternatively, you can press Start Scan instead of OK.

The HP All-in-One scans the image and saves the file to the memory card in the JPEG

format.

Make a copy

You can make quality copies from the control panel.

To make a copy from the control panel

1. Make sure you have paper loaded in the input tray.

2. Load your original print side down on the right front corner of the glass.

3. Press Start Copy Black or Start Copy Color to begin copying.

Replace the ink cartridges

Follow these instructions when you need to replace ink cartridges.

Chapter 3

20 HP Photosmart C6200 All-in-One series

English

La page charge ...

HP Photosmart C6200 All-in-One Printer series Mode d'emploi

HP Photosmart C6200 All-in-One Printer series Mode d'emploi

dans d''autres langues

Documents connexes