Extron SW HD 4K PLUS Series Manuel utilisateur
- Taper
- Manuel utilisateur
1
SW2/4 HD 4K PLUS • Setup Guide
The Extron SW HD 4K PLUS are two and four input HDMI switchers that support 4K video signals at 60 Hz. They
switch 4K/60 signals between multiple HDMI source devices to a single display. The switchers support computer and
video resolutions up to 4K/60 and 1080p/60, data rates up to 18 Gbps, HDR, 12-bit Deep Color, 3D, Lip Sync, and
HD lossless audio formats. Both models feature EDID Minder®, which maintains continuous EDID communication
with connected devices and ensures that the HDMI sources power up properly and maintain correct video output.
The switchers also provide automatic input cable equalization up to 25 feet (7.6 meters) when used with Extron
HDMI Pro Series cable.
The SW HD 4K PLUS Series offers control via front panel buttons, USB, Extron Product Control Software (PCS),
Ethernet, RS-232, contact closure, and auto-input switching for integration with any control system. Front panel LED
indicators provide immediate visual conrmation of HDCP authentication and signal presence for each input and
output.
This guide provides instructions for an experienced installer to set up and operate these switchers.
For full
installation, conguration, and operation details, see the SW HD 4K PLUS Series User Guide, available at
www.extron.com.
Rear Panel Features and Connections
SW2 HD 4K PLUS
-- AMAX
POWER
12V
1 2
LAN
CTCT+V
12
Tx Rx G
RS-232
INPUTS OUTPUT REMOTE
F
B
ACE
G
D
Figure 1. SW2 HD 4K PLUS Rear Panel
SW4 HD 4K PLUS
-- AMAX
POWER
12V
1 2 3 4
LAN
CTCT
34
CTCT+V
12
Tx Rx G
RS-232
INPUTS OUTPUT REMOTECONTACT / TALLY
F
G
B
ACDE
G
Figure 2. SW4 HD 4K PLUS Rear Panel
A 2-pole captive screw power connector E RS-232 connector
B HDMI input connectors F LAN Connector
C HDMI output connector G Contact closure input and tally output connectors
D Tally +V connectors
Installation Steps
1. Turn off all of the equipment and disconnect it from the power source.
2. Mount the switcher on a rack shelf or furniture (optional).
2
SW2/4 HD 4K PLUS • Setup Guide (Continued)
3. Connect HDMI input sources to one or more of the SW HD 4K PLUS input connectors (see gures 1 and 2,
B, on the previous page).
NOTE: LockIt® cable lacing brackets, one for each HDMI input and output connector, are provided with the
SW HD 4K PLUS. These brackets can be used to secure the HDMI cables to the rear panel connectors
to reduce stress on the HDMI connectors and prevent signal loss due to loose cable connections. For
information on attaching the LockIt brackets, see the LockIt HDMI Lacing Bracket instructions in the SW
HD 4K PLUS Series User Guide card, available at www.extron.com.
4. Connect an HDMI output device to the output connector (C). By default, the EDID of this device is stored at
the HDMI output.
5. Connect control devices. Connect your computer
to one of the following SW HD 4K PLUS
communication ports to congure and control the
switcher via SIS commands:
• RS-232 port — Connect the unterminated
transmit, receive, and ground wires of the RS-232
cable to the provided 3-pole captive screw plug, as
shown in the illustration at right. Connect the plug
between the rear panel Remote shared connector
(E), and the serial port of your computer. Protocol
for the RS-232 port is 9600 baud, 8 data bits, 1
stop bit, no parity.
• Config port — Connect a USB mini-B cable between the front panel USB connector (see gures 4 and 5,
B, on page 4) and a USB port on your computer for control via USB.
• LAN port — Use an RJ-45 cable to connect this jack (see figures 1 and 2, F) to a LAN for Ethernet control
of the switcher.
6. (Optional) Connect contact closure and indicator devices. The Contact/Tally section of the rear panel
contains one (SW2) or two (SW4) female captive screw connectors, each with two pairs of pins labeled C and T
(see 1 in the illustration below right).
Each pin pair is labeled with the number of the HDMI input associated with it. Wire devices to these connectors
as follows:
a. SW2 models — Wire and connect the provided 5-pole plug to the 5-pole Contact/Tally captive screw
connector on the rear panel.
SW4 models — Wire and connect the provided 5-pole plug to the Contact In/Tally Out connector on the
left (containing pin pairs 1 and 2), and wire and connect the provided 4-pole plug to the connector on the
right (pin pairs 3 and 4).
b. Connect contact input and tally output devices to the pin pair for each input you are using, as follows:
• To enable input switching via contact closure, connect a push-button
contact closure input device to pin C (2) and to the G (ground) pin
(5) of the 3-pole RS-232 connector.
• To identify the currently selected input when the front panel buttons
are not visible, connect an indicator device, such as an LED, to tally
output pin T (3) of the same pin pair.
When the input you are using is selected, the corresponding tally out
pin shorts to ground, which activates the connected indicator.
c. Insert the power wires for the contact indicator devices into the +V
connector (4).
d. Press the button on the contact closure device to switch the connected input to the
output.
Computer or
Control Syste
m
RS-232 Port
SW HD 4K Series Switcher
Rear Panel
Remote Port
NOTE: If you use cable that has a drain
wire, tie the drain wire to ground at both ends.
Ground (G)
Transmit (Tx)
Receive (Rx) Transmit (Tx)
Receive (Rx)
Tx Rx G
RS-232
1
1
1
4
4
4
CTCT
34
CTCT+V
12
Tx Rx G
RS-232
REMOTECONTACT / TALLY
2
2
23
3
35
5
5
3
Using a Show Me™ cable:
The Contact and Tally connectors can also be used with Extron Show Me cables. For
each cable The diagram at right shows how to wire a Show Me cable to a contact input.
For each Show Me cable:
• Connect the red pigtail to the C pin corresponding to the input being used.
• Connect the black pigtail to the T pin of the same input.
7. If not using the provided pre-wired power supply, wire a 2-pole captive screw connector
(provided) to your power supply as shown below in gure 3.
Captive Screw Connector
Tie Wrap
Heat
Shrink 1/8"
(3 mm)
7/8"
(22 mm)
3/16"
(5 mm) Max.
Figure 3. Wiring the Power Connector
ATTENTION:
• The power supply must not be permanently xed to the building structure or similar structures.
• La source d’alimentation ne devra pas être xée de façon permanente à une structure de bâtiment ou à
une structure similaire.
• These power supplies are not suitable for use in air handling spaces or in wall cavities.
• Ces sources d’alimentation ne sont pas appropriées pour une utilisation dans les espaces d’aération ou
dans les cavités murales.
• Do not connect power to the switcher until you have read the CAUTION and ATTENTION notices on
pages 5 and 6 of the SW HD 4K PLUS Series User Guide.
• Ne branchez pas l’alimentation au SW HD 4K PLUS Series User Guide avant d’avoir lu les mises en
garde « CAUTION » et «ATTENTION » aux pages 5 et 6.
8. Power on the output display.
9. Connect power to the switcher.
10. Power on the source devices.
CONTACT/TALLY
Connector
Black
Red
Show Me
Cable
CTCT+V
12
SW2 and SW4 HD 4K PLUS
468-2940-50 Rev. B
05 23
© 2023 Extron All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Front Panel Features
SW2 HD 4K PLUS
HDMI SWITCHER
1
RCONFIG
SIGNAL
INPUTS
INPUTS OUTPUT
12
HDCP
2
AUTO
SWITCH
C
C
C
DDD
F
B
B
B
A
E
Figure 4. SW2 HD 4K
PLUS
Front Panel
SW4 HD 4K PLUS
HDMI SWITCHER
RCONFIG
AUTO
SWITCH
1
INPUTS
2 3 4 SIGNAL
INPUTS OUTPUT
1234
HDCP
F
B
E
C
D
A
Figure 5. SW4 HD 4K
PLUS
Front Panel
A AUTO SWITCH LED — Lights when auto-input switching is in effect. When auto-input switching is enable, the
switcher automatically switches to the highest-number input with an active video signal.
B USB CONFIG port — Connect a USB cable (USB A to mini-B) between your computer and this female USB mini-B
port to configure and control the switcher via SIS commands or PCS, and to update the firmware.
C SIGNAL LEDs — The LEDs labeled INPUTS each light when the corresponding input is connected to a device that
has power. The LED labeled OUTPUT lights when the output is connected to a device that has power.
D HDCP LEDs
• Input LEDs — Light if the connected sources are HDCP encrypted and have been authenticated by the
switcher inputs.
NOTE: If the source device connected to the selected input is HDCP encrypted (requires HDCP
authentication), the corresponding signal LED may not light unless HDCP has been authenticated.
• Output LED — Lights when the currently selected input requires HDCP and the connected output device
has been successfully authenticated.
NOTE: HDCP is re-authenticated on the output whenever a new input is selected.
E Input selection buttons — Press one of these buttons to select an input to switch to the output. The LED at
the right of each button lights when the corresponding input is selected. If auto-input switching is in effect, these
buttons are disabled, but the LEDs continue to light to indicate the selected input. The input buttons are also
used to initiate a system reset and to enable and disable front panel lockout (see the SW HD 4K PLUS Series
User Guide for more information).
F Reset button — This button initiates two levels of reset of the switcher. For the different reset levels, press and
hold the button while the switcher is running or while you power up the switcher. (For more information about
reset levels, see the SW HD 4K PLUS User Guide at www.extron.com.)
A AUTO SWITCH LED
B USB CONFIG port
C SIGNAL LEDs
D HDCP LEDs
E Input selection buttons
F Reset button
-
1
-
2
-
3
-
4
