Kenwood FPM910 Le manuel du propriétaire

Catégorie
Robots culinaires
Taper
Le manuel du propriétaire
FPM91
FPM90
instructions
istruzioni
instrucciones
Bedienungsanleitungen
gebruiksaanwijzing
Instrukcja obsługi
instruções
TYPE: FPM90
TYPE: FPM91
English 3 - 16
Nederlands 17 - 31
Français 32 - 46
Deutsch 47 - 61
Italiano 62 - 76
Dansk 77 - 89
Svenska 90 - 102
Norsk 103 - 116
Suomi 117 - 130
(7
)3 )8
):
*2
*1
)9
*4
*8
*9
*:
)4
)5
)6
)7
*3
*5
*6
*7
(8
(9
(:
)1
)2
(2
(1
(6
(5
(4 (3
Type FPM91
A - standard attachments
B - optional attachments
)4
)5
(3
(4
(5
)3
)2
):
)8
)9
)7
(1
(7
(2
(6
)3 + )4 )8 *1
)5 + )6
*:
*7
*3 *6
)6
(8
(9
)1
(:
)7
a
b
*8
a
b
c
*9
a
b
*2
c
a
b
d
e
f
g
safety
ORead these instructions carefully and retain for future reference.
ORemove all packaging and any labels.
OIf the plug or cord is damaged it must, for safety reasons, be replaced by
Kenwood or an authorised Kenwood repairer in order to avoid a hazard.
OThe blades and discs are very sharp, handle with care. Always hold by
the finger grip at the top, away from the cutting edge, both
when handling and cleaning.
ODo not lift or carry the processor by the handle - or the handle may break
resulting in injury.
OAlways remove the knife blade before pouring contents from the bowl.
OKeep hands and utensils out of the processor bowl and blender goblet
whilst connected to the power supply.
OSwitch off and unplug:-
O
before fitting or removing parts;
O
when not in use;
O
before cleaning.
ONever use your fingers to push food down the feed tube. Always use the
pusher/s supplied.
ONever fit the blade unit to the power unit without the blender
goblet or compact chopper/grinder fitted.
OBefore removing the lid from the bowl or blender or compact chopper/
grinder from the power unit:-
O
switch off;
O
wait until the attachment/blades have completely stopped;
O
be careful not to unscrew the blender goblet or compact chopper/
grinder from the blade assembly.
ODO NOT process hot ingredients in the processor bowl.
ODo not use the lid to operate the processor, always use the on/off speed
control.
OThis appliance will be damaged and may cause injury if the
interlock mechanism is subjected to excessive force.
OAlways unplug your food processor when not in use.
ONever use an unauthorised attachment.
ONever leave the appliance unattended when it is operating.
ONever use a damaged appliance. Get it checked or repaired: see ‘service
& customer care’.
ONever let the power unit, cord or plug get wet.
ODon’t let excess cord hang over the edge of a table or worktop or touch
hot surfaces.
3
ODo not exceed the maximum capacities stated in the recommended speed
chart.
OThis appliance shall not be used by children. Keep the appliance and its
cord out of reach of children.
OChildren should be supervised to ensure that they do not play with the
appliance.
OAppliances can be used by persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe
way and if they understand the hazards involved.
OOnly use the appliance for its intended domestic use. Kenwood will not
accept any liability if the appliance is subject to improper use, or failure to
comply with these instructions.
OMisuse of your processor/blender can result in injury.
OThe maximum rating is based on the attachment that draws the greatest
load. Other attachments may draw less power.
Refer to the relevant section under “using the attachments” for additional
safety warnings for each individual attachment.
blender safety
O SCALD RISK: Hot ingredients must be allowed to cool to room
temperature before placing in the goblet or before blending.
OAlways take care when handling the blade assembly and avoid touching
the cutting edge of the blades when cleaning.
OBe careful if hot liquid is poured into the blender as it can be ejected out of
the appliance due to sudden steaming.
OOnly operate the blender with the lid in place.
OOnly use the goblet with the blade assembly supplied.
ONever run the blender empty.
OTo ensure the long life of your blender, do not run it for longer than 60
seconds.
OSmoothie recipes - never blend frozen ingredients that have formed a solid
mass during freezing, break it up before adding to the goblet.
OImportant - The skirt on the base of the goblet is fitted during
manufacture and no attempt should be made to remove it.
4
5
IMPORTANT: HOT
BLENDING INSTRUCTIONS
To minimise the possibility of scalding when blending hot ingredients keep
hands and other exposed skin away from the lid to prevent possible burns.
The following precautions must be observed:
OCAUTION: Blending very hot ingredients may result in hot
liquid and steam being forced suddenly past the lid or filler
cap (7.
OWe recommend that hot ingredients are allowed to cool
before blending.
ONEVER exceed 1200mls/5 cups capacity if processing hot liquids, such
as soups (refer to the markings on the goblet).
OALWAYS commence blending at a low speed and gradually increase
the speed. NEVER blend hot liquids by using the Pulse setting.
OLiquids which tend to foam such as milk, should be limited to a
maximum capacity of 1000mls/4 cups.
OTake care when handling the blender as the goblet and its contents will
be very hot.
OTake particular care when removing the lid. The lid is designed to be a
tight fit to prevent leakage. If necessary protect your hands with a cloth
or oven gloves when handling.
OEnsure the goblet is securely attached to the base and when removing
from the appliance, guide the base and ensure it is removed together
with the goblet.
OEnsure that the lid and filler cap are securely in place before every
blending operation.
OAlways ensure that the vents in the filler cap are clear before every
blending operation )2.
OWhen fitting the lid to the goblet always ensure that the lid and goblet
rim are clean and dry to ensure a good seal and prevent spillage.
slicing/grating disc safety
ONever remove the lid until the cutting disc has completely
stopped.
OHandle the cutting discs with care - they are extremely
sharp.
ODo not overfill the bowl – do not exceed the maximum
capacity level marked on the bowl.
compact chopper/grinder safety
ONever fit the blade unit to your food processor without the jar fitted.
ONever unscrew the jar while the compact chopper/grinder is fitted to your
appliance.
ODo not touch the sharp blades – Keep the blade unit away from children.
ONever remove the compact chopper/grinder until the blades have
completely stopped.
OTo ensure the long life of your compact chopper/grinder, do not run it
continuously for longer than 60 seconds. Switch off as soon as you have
got the right consistency.
OThe appliance will not work if the compact chopper/grinder is incorrectly
fitted.
ODo not process turmeric root in the compact chopper/grinder as it is too
hard and may damage the blades.
juice extractor safety
ODo not use the juice extractor if the filter is damaged.
OOnly use the pusher supplied. Never put your fingers in the feed tube.
Unplug before unblocking the feed tube.
OBefore removing the lid, switch off and wait for the filter to stop.
6
before plugging in
O Make sure your electricity supply is the same as the one
shown on the underside of your appliance.
O WARNING: THIS APPLIANCE MUST BE EARTHED.
O This appliance conforms to EC Regulation 1935/2004 on
materials and articles intended to come into contact with
food.
before using for the first time
1 Remove the plastic blade covers from the knife blade.
Take care the blades are very sharp. These covers
should be discarded as they are to protect the blade during
manufacture and transit only.
2 Wash the parts see ‘care & cleaning’
key
processor
power unit
detachable drive shaft
bowl
lid
wide feed tube
pushers
safety interlocks
cord storage (at back)
power on light
(1 auto button
(2 speed/pulse control
weighing function (Type FPM91)
(3 kg/lb button
(4 display screen
(5 on/zero button
(6 weighing tray
thermoresist blender
(7 filler cap
(8 lid
(9 goblet
(: sealing ring
)1 blade unit
)2 filler cap vents
A - standard attachments
)3 knife blade
)4 dough tool
)5 dual whisk
)6 folding tool
)7 max capacity disc
)8 4mm slicing disc
)9 2mm slicing disc
): 4mm grating disc
*1 2mm grating disc
*2 attachment storage box
B - optional attachments
Not all the attachments listed below will be included with your
food processor model. Attachments are dependent upon the
model variant. For more information or to order additional
attachments refer to the “service and customer care” section.
*3 extra fine grater disc (if supplied)
*4 fine Julienne disc (if supplied)
*5 decorative slicing disc (if supplied)
*6 French fry disc (if supplied)
*7 mini bowl and blade (if supplied)
*8 compact chopper/grinder (if supplied)
*9 citrus juicer (if supplied)
*: metal juicer extractor (if supplied)
to use your food processor
1 Fit the detachable drive shaft onto the power unit – push
down lightly to ensure the drive shaft is fully engaged.
2 Then fit the bowl to the power unit. Place the handle
towards the back on the right hand side and turn clockwise
until it locks.
3 Fit an attachment over the bowl drive shaft.
O Always fit the bowl and attachment onto the processor
before adding ingredients.
4 Fit the lid - ensuring the top of the drive shaft/tool locates
into the centre of the lid.
5 Fit the pushers to the feed tube – turn the small pusher
clockwise to lock in position .
O The processor will not operate if the bowl, lid or
wide feed tube pusher are not fitted correctly
into the interlocks. Check that the feed tube and
bowl handle are situated to the right hand side.
6 Plug in. The Power On light will come on and flash until the
bowl and lid are fitted correctly. Select one of the following
options: -
Auto Button – the light will come on when the Auto Button is
pressed and the optimum speed for the attachment will be
automatically selected.
Speed Control – manually select the required speed (refer to
the recommended speed chart).
Pulse – use the pulse (P) for short bursts. The pulse will
operate for as long as the control is held in position.
7 At the end of processing turn the speed control to the ‘O’
off position or if using the Auto press the button and the
light will go out.
O The Power On light will flash if either the lid,
bowl or wide feed tube are not fitted.
O The Power On and Auto lights will flash if the
Auto is selected but the interlocks are not
engaged.
O The Auto Button will not operate if a speed is
selected on the speed control.
O Always switch off and unplug before removing
the lid.
important
O Your processor is not suitable for crushing or grinding coffee
beans, or converting granulated sugar to caster sugar.
7
Eco function
If the food processor is left plugged in for over 30 minutes
without being used, it will go into standby mode to reduce
energy consumption.
O The Power On light will pulse slowly and the food processor
will not operate until one of the following actions are carried
out:-
O The Auto Button is pressed.
O The speed control is turned to a speed and then turned
back to the ‘O’ off position.
The light will change to being constantly lit when ready to
use.
Note: If the bowl or lid are not engaged into the interlock the
power on light will pulse more rapidly than the Eco function.
weighing function (Type FPM91)
Your food processor is fitted with a built in weighing function
to allow ingredients to be weighed straight into the bowl or
blender goblet.
O The Maximum weighing capacity is 3Kg. This is the total
weight of all the ingredients including the weight of the bowl
or goblet.
to use the weighing function
1 Always fit the detachable drive
shaft, bowl and attachment or
blender goblet onto the power unit
before adding ingredients.
2 Plug in – the display screen will
remain blank.
3 Press the ON/ZERO button once
and the display screen will light up.
4 Press the (kg/lb) button to select
either grams or ounces. The
display will default to kg/g when
first switched on.
O The unit weighs in 2g increments
and teaspoon/tablespoon measures are recommended for
weighing small quantities.
5 Check the display shows ‘0’, if not, zero by pressing the ON/
ZERO button. Then weigh the required ingredients straight
into the bowl or goblet. After the weight is displayed, press
the ON/ZERO button and the display will return to ‘0’.
Add the next ingredients and that weight will be displayed.
Repeat until all ingredients are weighed.
O If the display is not zeroed and either the ingredients or the
bowl/attachment/lid are removed the display will show
[ - - - -] to represent a minus reading.
To zero press the ON/ZERO button once.
6 Add the lid and select a speed to operate the processor.
O During operation the display screen will freeze [- - - -] until
the speed control returned to the ‘O’ off position.
O After processing the last weight will be displayed on the
screen when the speed control is returned to the ‘O’ off
position. Note: The weight of the lid will be included if the
display is not zeroed before switching on.
O The weight of any additional ingredients added down the
feed tube whilst the processor is running will not be shown
on the display screen.
(6 weighing tray
A removable weighing tray
is supplied for weighing
ingredients without the bowl or
blender.
To use, place the tray on top
of the power unit. Then follow
steps 2 to 5 under ‘to use the
weighing function’.
To remove, just lift the tray off.
auto switch off
O The display screen will turn off automatically if the same
weight reading is shown after 5 minutes.
O The display screen can be turned off manually by pressing
and holding down the ON/ZERO button for a few seconds.
important
O Do not overload by exceeding the maximum weighing
capacity of 3Kg. The display will show [0 – Ld] if the
weighing function is overloaded.
O Do not subject the power unit to excessive force as this may
damage the weighing sensor.
O Always place the processor on a dry flat surface prior to
weighing.
O Do not move the power unit during operation of the weighing
function.
to use your thermoresist blender
1 Fit the sealing ring (: into the blade unit )1 - ensuring the
seal is located correctly in the grooved area.
O Leaking will occur if the seal is damaged or
incorrectly fitted.
2 Hold the underside of the blade unit )1 and insert the blades
into the goblet - turn anti-clockwise until it clicks . Refer to
the graphics on the underside of the blade unit as follows:
- unlocked position
- locked position
The blender will not work if incorrectly
assembled.
3 Put your ingredients into the goblet.
4 Fit the lid to the goblet and push down to secure . Fit the
filler cap.
5 Place the blender onto the power unit, and turn clockwise
to lock.
O The appliance will not operate if the blender is
incorrectly fitted to the interlock.
6 Select Auto, or a speed (refer to the recommended speed
chart) or use the pulse control.
hints
O When making mayonnaise, put all the ingredients, except
the oil, into the blender. Remove the filler cap. Then, with the
appliance running, add the oil slowly through the hole in the
lid.
O Thick mixtures, e.g. pâtés and dips, may need scraping down.
If the mixture is difficult to process, add more liquid.
O Ice crushing - operate the pulse in short bursts until crushed to
the desired consistency.
O The processing of spices is not recommended as they may
damage the plastic parts.
O The appliance will not work if the blender is incorrectly fitted.
8
O To blend dry ingredients - cut into pieces, remove the filler
cap, then with the appliance running, drop the pieces down
one by one. Keep your hand over the opening. For best
results empty regularly.
O Don’t use the blender as a storage container. Keep it empty
before and after use.
O Never blend more than 1.6 litres (56 fl oz) - less for frothy
liquids like milkshakes.
9
recommended speed chart
tool/attachment function recommended processing maximum
speed time N capacities
Knife blade All in one cake mixes 8 15-20 secs 2Kg/4lb 8oz
total weight
Pastry - rubbing fat into flour 5 – 8 10 secs 500g/1lb 2oz
flour weight
Adding water to combine pastry ingredients 10-20 secs
Chopping fish and lean meat Pulse – 8 10-30 secs 1Kg/2lb 4oz
Pâtés and terrines max lean beef
Chopping vegetables Pulse 5-10 secs 500g/1lb 2oz
Chopping nuts 8 30-60 secs 200g/8oz
Pureeing soft fruit, cooked fruit and vegetables 8 10-30 secs 1Kg/2lb 4oz
Sauces, dressing and dips 8 2 mins max 800g/1lb 8oz
Knife blade with Cold soups Start at low 30-60 secs 2 litres/4pts
max capacity disc speed and
Milkshakes/batters increase to 15-30 secs 1.5 litres/2pts 12 fl oz
maximum
Dual whisk Egg whites 8 60-90 secs 2 – 8 (70g – 280g)
Egg & sugar for fatless sponges 8 4-5 min 3 eggs (150g)
Cream 8 30 secs 250 mls – 750mls
9 fl oz – 27 fl oz
Folding tool Whipping cream and fruit purees 1 – 2 60 secs 300g/12oz cream,
300g/12oz puree
Egg whites into heavy mixtures 1 – 2 60 secs 600g/1lb 6oz total wt
Macaroons 1 – 2 60 secs 500g/1lb 2oz total wt
Dough tool Yeasted mixes 8 60 secs 1.3Kg/ 2lb 12oz total wt
White Bread Flour 8 60 secs 650g/1lb 8oz flour wt
Wholemeal Bread Flour 8 60 secs 500g/1lb 2oz flour wt
Discs - slicing/grating Firm food items such as carrots, hard cheeses 5 – 8
Softer items such as cucumbers, tomatoes 1 – 5
Extra fine grater Parmesan cheese, potatoes for German 8
potato dumplings
Fine Julienne disc Potato straws and rosti 8
Stir fries and vegetable garnishes
Decorative slicing Firm food items such as carrots and potatoes 5 – 8
disc Softer food items such as cucumber
French fry disc Cuts potatoes for thin French Fries and 8
ingredients for casseroles and dips
(eg cucumber, apple and pear.)
Thermoresist blender Cold liquids and drinks 8 15-30 secs 1.6 litres/56 fl oz
Stock based soups 8 30 secs 1.2 litres/42 fl oz
Soups using milk 8 30 secs 1 litres/2pts
We recommend that hot ingredients are allowed to cool before blending. However should you wish to process
hot ingredients please read the Hot Blending Safety instructions.
Mini bowl and knife Meat 8 20 secs + Pulse 300g/12oz Lean beef
Chopping herbs 8 30 secs 20g/1oz
Chopping nuts 8 30 secs 100g/4oz
Mayonnaise 8 30 secs 2 Eggs
300g/12oz Oil
Purees 8 30 secs 200g/8oz
Do not fill above
the maximum capacity
marked on the bowl
10
recommended speed chart
tool/attachment function recommended processing maximum
speed time N capacities
Compact chopper/ Processing a range of spices 8 30-60 secs 100g/4oz
grinder Grinding coffee beans 8 30 secs 75g/3oz
Chopping nuts Pulse 5 secs 140g/5oz
Lean braising steak (cut into 2cm cubes) Pulse 10 secs 200g/8oz
Citrus Juicer Smaller items i.e. limes and lemons 1 – 2 2Kg/4lb 8oz
Larger fruits i.e. oranges and grapefruits
Juice extractor Juicing firm fruit and vegetables auto 1Kg/2lb 4oz apples
ie apples and carrots 800g/1lb 12oz carrots
Juicing soft fruits ie grapes and auto 500g/1lb 2oz
tomatoes
NThis is for guidance only and will vary depending on the exact recipe and ingredients being processed.
using the attachments
Refer to recommended speed chart for each attachment.
)3 knife blade
The knife blade is the most versatile of all the attachments.
The length of the processing time will determine the texture
achieved. For coarser textures use the pulse control.
Use the knife blade for cake and pastry making, chopping
raw and cooked meat, vegetables, nuts, pâté, dips, pureeing
soups and to also make crumbs from biscuits and bread.
hints
O Cut food such as meat, bread, vegetables into cubes
approximately 2cm/3/4in before processing.
O Biscuits should be broken into pieces and added down the
feed tube whilst the appliance is running.
O When making pastry use fat straight from the fridge cut into
2cm/3/4in.cubes.
O Take care not to over-process.
)4 dough tool
Use for yeasted dough mixes.
O Place the dry ingredients in the bowl and add the liquid
down the feed tube whilst the appliance is running. Process
until a smooth elastic ball of dough is formed this will take
approx. 60 secs.
O Re-knead by hand only. Re-kneading in the bowl is not
recommended as it may cause the processor to become
unstable.
)5 dual whisk
Use for light mixtures only e.g. egg whites, cream,
evaporated milk and for whisking eggs and sugar for fatless
sponges. Heavier mixtures such as fat and flour will damage
it.
using the whisk
1 Fit the detachable drive shaft and bowl onto the power unit.
2 Push each beater
securely into the drive head.
3 Fit the whisk by carefully turning until it drops over the drive
shaft.
4 Add the ingredients.
5 Fit the lid - ensuring the end of the shaft locates into the
centre of the lid.
6 Switch on.
important
O The whisk is not suitable for making all in one
cake mixes as these mixes are too heavy and will
damage it. Always use the knife blade.
hints
O Best results are obtained when the eggs are at room
temperature.
O Ensure the bowl and whisks are clean and free from grease
before whisking.
O Heavier ingredients such as flour and dried fruit should be
folded in by hand.
O Do not exceed the maximum capacity or processing time
stated in the recommended speed chart.
)6 folding tool
Use the folding tool to fold light ingredients into heavier
mixtures for example meringues, mousses and fruit fools.
1 Fit the detachable drive shaft and bowl onto the power unit.
2 Push the paddle securely into the drive head.
3 Fit the folding tool by carefully turning until it drops over the
drive shaft.
4 Add the ingredients.
5 Fit the lid – ensuring the end of the shaft locates into the
centre of the lid .
6 Select low speed (speed 1 -2).
to remove the beater
Detach the beater from the drive head by pressing the
release button (1.
hints
O Do not use Auto or high speed as a low speed is required to
optimise the folding performance.
O For best results do not over whisk egg whites or cream –
the folding tool will not be able to fold the mixture correctly if
the whisked mix is too firm.
O Do not fold the mixture for longer than stated in the
recommended speed chart as the air will be knocked out
and the mix will be too loose.
O Any unmixed ingredients left on the paddle or sides of the
bowl should be carefully folded in using the spatula.
)7 max capacity disc
When blending liquids, use the max capacity disc with the
knife blade. It allows you to increase the liquid processing
capacity from 1.4 litre to 2 litres, prevents leaking and
improves the chopping performance of the blade.
1 Fit the detachable drive shaft and bowl onto the power unit.
2 Fit the knife blade.
3 Add ingredients to be processed.
4 Fit the capacity disc over the top of the blade ensuring it sits
on the ledge inside the bowl (2. Do not push down on
the capacity disc.
5 Fit the lid and switch on.
slicing/grating discs
slicing discs - 4mm
)8, 2mm )9
Use the slicing side for cheese, carrots, potatoes, cabbage,
cucumber, courgette, beetroot and onions.
grating discs - 4mm ):, 2mm *1
Use the grating side for cheese, carrots, potatoes and foods
of a similar texture.
extra fine grater disc *3 (if supplied)
Grates Parmesan cheese and potatoes for German potato
dumplings.
fine julienne
*4 (if supplied)
Use to cut potatoes into straws and coarse grate for rosti,
stir fries and vegetable garnishes.
decorative slicing disc
*5 (if supplied)
Use to slice potatoes, carrot, cucumbers and foods of a
similar texture into fluted shaped slices.
French fry disc *6 (if supplied)
Cuts potatoes for thin French Fries and ingredients for
casseroles and dips (eg cucumber, apple and pear.)
safety
O Never remove the lid until the cutting disc has
completely stopped.
O Handle the cutting discs with care - they are
extremely sharp.
O Do not overfill the bowl – do not exceed the
maximum capacity level marked on the bowl.
to use the cutting discs
1 Fit the detachable drive shaft and bowl onto the power unit..
2 Holding by the centre grip, place the disc onto the drive shaft
with the appropriate side uppermost (3.
3 Fit the lid.
4 Put the food in the feed tube.
Choose which size feed tube you want to use. The pusher
contains a smaller feed tube for processing individual items
or thin food items.
To use the small feed tube – first put the large pusher inside
the feed tube.
To use the wide feed tube – fit the small pusher into the
wide pusher and turn clockwise to lock in place.
Do not fill the feed tube above the maximum level as the
processor will not operate unless the wide feed tube pusher
is fitted correctly.
5 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube.
hints
O Use fresh ingredients
O Don’t cut food too small. Fill the width of the feed tube fairly
full. This prevents the food from slipping sideways during
processing. Alternatively use the small feed tube.
O When using the Julienne disc, place ingredients horizontally.
O When slicing or grating: food placed upright (4 comes out
shorter than food placed horizontally (5.
O Food placed upright comes out shorter than food placed
horizontal.
O There will always be a small amount of waste on the disc or
in the bowl after processing.
11
*7 mini bowl and knife (if supplied)
Use the mini processor bowl to chop herbs and process
small quantities of ingredients e.g. meat, onion, nuts,
mayonnaise, vegetables, purées, sauces and baby food.
Do not overfill the bowl.
a mini blade
b mini bowl
to use the mini bowl and knife
1 Fit the detachable drive shaft and bowl onto the power unit.
2 Fit the mini bowl over the detachable drive shaft - ensure the
cut out sections align with the locating tabs (6 on the main
bowl.
Note: The main bowl lid cannot be fitted if the mini bowl is
not located correctly.
3 Place the knife blade over the drive shaft (7.
4 Add the ingredients to be processed.
5 Fit the lid and switch on.
safety
O Never remove the lid until the knife blade has completely
stopped.
O The knife blade is very sharp - always handle with care.
important
O Do not process spices – they may damage the plastic.
O Do not process hard food such as coffee beans, ice cubes
or chocolate – they may damage the blade.
hints
O Herbs are best chopped when clean and dry.
O Always add a little liquid when blending cooked ingredients
to make baby food.
O Cut foods such as meat, bread, vegetables into cubes
approximately 1-2 cm (1234 in) before processing.
O When making mayonnaise add the oil down the feed tube.
*8 compact chopper/grinder (if supplied)
Use the compact chopper/grinder for processing dry
ingredients such as nuts, coffee beans and it is also suitable
for processing a range of spices such as: -
Black peppercorns, cardamom seeds, cumin seeds,
coriander seeds, fennel seeds, fresh ginger root, fresh
chillies and whole cloves.
a sealing ring
b blade unit
c glass jar
to use your compact chopper/grinder
1 Put your ingredients into the jar. Fill it no more than half full.
2 Fit the sealing ring to the blade unit.
3 Hold the underside of the blade unit and insert the blades
into the jar – turn anti-clockwise to lock (8.
4 Place the compact chopper/grinder onto the power unit and
turn clockwise to lock (9.
5 Use the Auto button, or select a speed (refer to the
recommended speed chart).
safety
O Never fit the blade unit to your food processor without the
jar fitted.
O Never unscrew the jar while the compact chopper/grinder is
fitted to your appliance.
O Do not touch the sharp blades – Keep the blade unit away
from children.
O Never remove the compact chopper/grinder until the blades
have completely stopped.
O To ensure the long life of your compact chopper/grinder, do
not run it continuously for longer than 60 seconds. Switch
off as soon as you have got the right consistency.
O The appliance will not work if the compact chopper/grinder
is incorrectly fitted.
O Do not process turmeric root in the compact chopper/
grinder as it is too hard and may damage the blades.
hints
O For optimum performance when processing spices we
recommend that you do not process more than 100g at a
time in the compact chopper/grinder.
O Whole spices retain their flavour for a much longer time than
ground spices so it is best to grind a small quantity fresh at
a time to retain the flavour.
O To release the maximum flavour and essential oils whole
spices are best roasted prior to milling.
O Cut ginger up into small pieces before processing.
O For best results the mini bowl attachment is recommended
when chopping herbs.
*9 citrus juicer (if supplied)
Use the citrus juicer to squeeze the juice from citrus fruits
(eg oranges, lemons, limes and grapefruits).
a cone
b sieve
to use the citrus juicer
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2 Fit the sieve into the bowl - ensuring the sieve handle is
locked into position directly over the bowl handle (:.
3 Place the cone over the drive shaft turning until it drops all
the way down )1.
4 Cut the fruit in half. Then switch on and press the fruit onto
the cone.
O The citrus juicer will not operate if the sieve is
not locked correctly.
O For best results store and juice the fruit at room temperature
and hand roll on a worktop before juicing.
O To help with juice extraction move the fruit from side to side
when juicing.
O When juicing large quantities, empty the strainer regularly to
prevent the build up of pulp and seeds.
12
*: metal juice extractor (if supplied)
Use the centrifugal juicer for making juice from firm fruit and
vegetables.
a pusher
b lid
c pulp remover
d filter drum
e bowl
f juicing spout
g juice extractor drive adaptor
to use the juice extractor
1 Fit the drive adaptor onto the power unit )2 – push down
lightly to ensure the adaptor is located correctly.
2 Then fit the bowl. Place the handle towards the back and
turn clockwise until it locks )3.
3 Place the pulp remover into the filter drum - ensuring the
tabs locate with the slots in the bottom of the drum )4.
4 Fit the filter drum )5.
5 Place the attachment lid onto the bowl, turn until it locks
and the feed tube sits over the handle )6. Your juice
extractor will not operate if the bowl or lid are
not fitted correctly into the interlock.
6 Place a suitable glass or jug under the juice outlet.
7 Cut the food to fit the feed tube.
8 Select Auto and push down evenly with the pusher - never
put your fingers in the feed tube. Process fully before
adding more.
O After adding the last piece, let the juice extractor run for
a further 30 seconds to extract all the juice from the filter
drum.
safety
O Do not use the juice extractor if the filter is
damaged.
O Only use the pusher supplied. Never put your fingers in the
feed tube. Unplug before unblocking the feed tube.
O Before removing the lid, switch off and wait for the filter to
stop.
important
O If the juice extractor starts to vibrate, switch off and empty
the pulp from the drum. (The juice extractor vibrates if the
pulp becomes unevenly distributed).
O Maximum capacity that can be processed at one time is
1Kg of fruit or vegetables (refer to speed chart).
O Some very hard foods may make your juice extractor slow
down or stop. If this happens switch off and unblock the
filter.
O Switch off and clear the pulp collector regularly during use.
hints
O Before processing remove stones and pips (eg pepper,
melon, plum) and tough skins (eg melon, pineapple). You
don’t need to peel or core apples and pears.
O Use firm, fresh fruit and vegetables.
O To maximise juice extraction place small quantities at a time
in the feed tube and push down slowly.
O Citrus fruit - peel and remove the white pith, otherwise the
juice may taste bitter. For best results use the citrus juicer.
*2 attachment storage box
Your food processor is supplied with a storage box for your
bowl attachments and discs.
1 Fit the knife blade and discs into the storage box when not
in use )7.
2 The storage box is fitted with a safety lock - close the lid to
lock. To open, push the tab in )8 and lift up the lid )9.
care & cleaning
O Always switch off and unplug before cleaning.
O Handle the blades and cutting discs with care -
they are extremely sharp.
O Some foods may discolour the plastic. This is perfectly
normal and won’t harm the plastic or affect the flavour
of your food. Rub with a cloth dipped in vegetable oil to
remove the discolouration.
power unit
O Wipe with a damp cloth, then dry. Ensure that the interlock
area is clear of food debris.
O Don’t immerse the power unit in water.
O Store excess cord in the storage area at the back of the
power unit ):.
blender and compact chopper/grinder
1 Empty the goblet/jar, unscrew the blade unit by turning to
the unlock position to release.
2 Wash the goblet/jar by hand.
3 Remove and wash the seals.
4 Don’t touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don’t
immerse the blade unit in water.
5 Leave to dry upside down.
dual whisk
O Detach the beaters from the drive head by gently pulling
them free. Wash in warm soapy water.
O Wipe the drive head with a damp cloth, then dry. Do not
immerse the drive head in water.
folding tool
O Detach the beater from the drive head by pressing the
release button (1. Wash in warm soapy water.
O Wipe the drive head with a damp cloth, then dry. Do not
immerse the drive head in water.
centrifugal juicer
O The cutting blades on the base of the filter drum are very
sharp, take care when handling and cleaning the drum.
O Some foods may discolour the plastic. This is perfectly
normal and won’t harm the plastic or affect the flavour
of your food. Rub with a cloth dipped in vegetable oil to
remove the discolouration.
juice drive adaptor
O Wipe with a damp cloth, then dry
O Do not immerse the adaptor in water.
13
all other parts
O Wash by hand, then dry.
O Alternatively they are dishwasher safe and can be washed
on the top rack of your dishwasher. Avoid placing items
on the bottom rack directly over the heating element. A
short low temperature (Maximum 50°C) programme is
recommended.
service & customer care
O If you experience any problems with the operation of
your appliance, before requesting assistance refer to the
“troubleshooting guide” section in the manual or visit
www.kenwoodworld.com.
O Please note that your product is covered by a warranty,
which complies with all legal provisions concerning any
existing warranty and consumer rights in the country where
the product was purchased.
O If your Kenwood product malfunctions or you find any
defects, please send it or bring it to an authorised
KENWOOD Service Centre. To find up to date details of
your nearest authorised KENWOOD Service centre visit
www.kenwoodworld.com or the website specific to your
Country.
O Designed and engineered by Kenwood in the UK.
O Made in China.
IMPORTANT INFORMATION FOR CORRECT
DISPOSAL OF THE PRODUCT IN ACCORDANCE
WITH THE EUROPEAN DIRECTIVE ON WASTE
ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
At the end of its working life, the product must not be disposed
of as urban waste.
It must be taken to a special local authority differentiated waste
collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving
from inappropriate disposal and enables the constituent
materials to be recovered to obtain significant savings in
energy and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a
crossed-out wheeled dustbin.
14
item suitable for
dishwashing
main bowl, mini bowl, lid, pusher
knife blades, dough tool
detachable drive shaft
discs
max capacity disc
whisk beaters/folding tool paddle
Do not immerse the drive head in
water
blender goblet, lid, filler cap
blade unit and seal for blender
blade unit and seal for compact
chopper/grinder
compact chopper/grinder jar
citrus juicer
metal juice extractor
juice drive adaptor
spatula
15
troubleshooting guide
Problem Cause Solution
The processor will not operate. No Power. Check processor is plugged in.
No power/indicator light not lit.
Bowl not fitted to power unit correctly. Check bowl is located correctly
and the handle is situated
towards the right hand side.
Bowl lid not locked on correctly. Check that the lid interlock is
located correctly into the
handle area.
The processor will not
work if the bowl and lid
are fitted incorrectly.
Eco function operating. Press either the Auto Button or
turn speed control on, then
return to ‘O’ to switch off Eco
function.
If none of the above check the
fuse/circuit breaker in your home.
Compact chopper/grinder will not operate. Compact chopper/grinder not locked on correctly. The compact chopper/grinder will
not operate if fitted incorrectly to
the interlock.
Compact chopper/grinder not assembled correctly. Check blade unit is fully tightened
onto the compact chopper/grinder
jar.
Blender will not operate. Blender not locked on correctly. The blender will not operate if
fitted incorrectly to the
interlock.
Blender not assembled correctly. Check blade unit is fully
tightened into the goblet.
Processor stops or slows Overload protection operated. Switch off, unplug and allow
during processing. Processor overloaded or overheated during the appliance to cool down for
operation. approximately 15 minutes.
Maximum capacity exceeded. Refer to the speed chart for
maximum capacities to
process.
Weighing function
Display screen freezes on [- - - -]. Quantity weighed too small. Use teaspoon and tablespoon
measures for very small
quantities.
Weight changed on display screen. Power unit moved during operation. Do not move unit during use.
Zero the display before
weighing next ingredients.
Power On light flashing rapidly. Normal operation. Check interlocks are engaged
The light will flash if the bowl, lid or blender are correctly.
not fitted to the power unit or not locked in
place correctly.
Power On light flashing slowly. Normal operation.
Food processor left plugged in for over 30 minutes Press either the Auto Button or
without being operated and gone into Eco mode. turn speed control on and then
return to ‘O’ to switch off Eco
function.
Auto and Power On light flashing. Normal operation. Check interlocks are engaged
The light will flash if the Auto selected but correctly or press the Auto
interlocks not engaged. button to switch off the Auto
function.
16
troubleshooting guide
Problem Cause Solution
Blender or compact chopper/grinder Seal missing. Check seal is fitted correctly and
leaking from blade assembly base. Seal incorrectly fitted. not damaged. To obtain a
Seal damaged. replacement seal see
“service & customer care”.
Blender seal missing from blade unit when The seal is packed pre-fitted to the blade unit. Unscrew goblet and check that
removed from packaging. seal is fitted to blade unit.
To obtain a replacement seal
see “service & customer care”.
Poor performance of tools/attachments. Refer to hints in relevant “using the attachment” section. Check attachments are
assembled correctly.
veiligheid
OLees deze instructies zorgvuldig door en bewaar ze voor toekomstig
gebruik.
OVerwijder de verpakking en alle labels.
OAls de stekker of het snoer beschadigd is, moet het om veiligheidsredenen
door Kenwood of een door Kenwood geautoriseerd reparatiebedrijf
vervangen worden, om gevaar te voorkomen.
ODe messen en de schijven zijn erg scherp; ga er dus voorzichtig mee om.
Houd ze bij het hanteren en schoonmaken altijd bovenaan bij
de vingergreep en weg van het snijvlak, vast.
OTil de keukenmachine niet bij het handvat op en draag hem evenmin op
die manier; hierdoor kan het handvat afbreken, waardoor u letsel kunt
oplopen.
OVoordat u de inhoud uit de kom giet, dient u altijd eerst het mes te
verwijderen.
OHoud uw handen en keukengereedschap uit de kom van de
keukenmachine en de beker van de blender, wanneer deze op het lichtnet
is aangesloten.
OSchakel het apparaat uit en haal de stekker uit het stopcontact:-
O
voordat u onderdelen aanbrengt of verwijdert;
O
als u het apparaat niet gebruikt;
O
voor het reinigen.
OGebruik nooit uw vingers om voedsel in de invoerkoker te duwen. Gebruik
altijd de bijgeleverde stamper.
OZet het mes nooit op het motorblok zonder dat de beker van
de blender of het compacte hak/molenhulpstuk is bevestigd.
OVoordat u het deksel van de kom haalt of de blender of het compacte
hak/molenhulpstuk van het motorblok verwijdert:-
O
zet het apparaat uit;
O
wacht totdat de hulpstukken / messen helemaal tot stilstand zijn
gekomen;
O
zorg dat u de blenderbeker of het compacte hak/molenhulpstuk niet
losschroeft van de messeneenheid.
O Verwerk hete ingrediënten NIET in de kom van de keukenmachine.
OGebruik nooit het deksel om de keukenmachine te bedienen, maar altijd de
aan/uit-knop.
OAls teveel kracht wordt uitgeoefend op het
vergrendelingsmechanisme, wordt dit apparaat beschadigd
en kan het letsel veroorzaken.
OHaal de stekker altijd uit de keukenmachine wanneer u hem
niet gebruikt.
17
Nederlands
Vouw voor het lezen a.u.b. de voorpagina met illustraties uit
OGebruik nooit een niet bij het apparaat behorend hulpstuk.
OLaat het apparaat nooit onbeheerd terwijl het aan staat.
OGebruik nooit een beschadigd apparaat. Laat het nakijken of repareren:
zie Onderhoud en klantenservice.
OLaat het motorhuis, het netsnoer of de stekker nooit nat worden.
OLaat het snoer nooit over de rand van een tafel of werkblad hangen of in
aanraking komen met hete oppervlakken.
OU mag de maximum capaciteit die in de snelheidstabel wordt aangegeven,
niet overschrijden.
ODit apparaat mag niet door kinderen worden gebruikt. Houd het apparaat
en het snoer buiten het bereik van kinderen.
OOp kinderen moet toezicht gehouden worden om er zeker van te zijn dat
ze niet met het apparaat spelen.
ODit apparaat kan worden gebruikt door personen met verminderde
lichamelijke, sensorische of geestelijke capaciteiten of gebrek aan ervaring
en kennis mits ze onder toezicht staan of instructie hebben gekregen over
het veilige gebruik van het apparaat, en de betrokken risico’s begrijpen.
OGebruik het apparaat alleen voor het huishoudelijke gebruik waarvoor
het is bedoeld. Kenwood kan niet aansprakelijk worden gesteld in als het
apparaat is misbruikt of als deze instructies niet zijn opgevolgd.
OMisbruik van uw keukenmachine/blender kan tot letsel leiden.
OHet maximum vermogen is afhankelijk van het hulpstuk dat de grootste
hoeveelheid energie verbruikt. Andere hulpstukken verbruiken misschien
minder energie.
Raadpleeg de betreffende paragraaf onder De hulpstukken gebruiken voor
aanvullende veiligheidswaarschuwingen voor ieder hulpstuk afzonderlijk.
veiligheid m.b.t. de blender
OKANS OP BRANDWONDEN: Laat hete ingrediënten altijd tot
kamertemperatuur afkoelen voordat u ze in de beker plaatst of verwerkt.
OWees voorzichtig wanneer u de messen hanteert en raak het snijvlak van
de messen bij het reinigen niet aan.
OWees voorzichtig wanneer u hete vloeistof in de blender giet, omdat deze
vloeistof plotseling in de vorm van stoom weer uit het apparaat gestoten
kan worden.
OLaat de blender uitsluitend voorzien van deksel lopen.
OGebruik de kan uitsluitend met de bijgeleverde messen.
ODe blender nooit leeg gebruiken.
OOm een lange levensduur van uw blender te garanderen, mag u hem nooit
langer dan 60 seconden gebruiken.
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134

Kenwood FPM910 Le manuel du propriétaire

Catégorie
Robots culinaires
Taper
Le manuel du propriétaire