Titan Hydra X Manuel utilisateur

HYDRA X™

4540

7230

0323 • Form No. 2412595G

OPERATION MANUAL

- EN - OPERATION MANUAL 2

- F - MODE D’EMPLOI 28

- ES - INSTRUCCIONES DE USO 54

UNITED STATES SALES & SERVICE

WEB: www.titantool.com

PHONE: 18005265362

1770 Fernbrook Lane

Minneapolis, MN 55447

AIRLESS, HIGH-PRESSURE SPRAYING UNIT

GROUPE DE PROJECTION À HAUTE PRESSION

AIRLESS EQUIPO DE ALTA PRESIÓN PARA

PULVERIZAR

Models*:

49 STATE

2412275 4540 / 4500 PSI

2412277 7230 / 7250 PSI

2424560 4540 / 4500 PSI / 250’ COMPLETE

2424561 7230 / 7250 PSI / 250’ COMPLETE

50 STATE

2412275X 4540 / 4500 PSI

2412277X 7230 / 7250 PSI

2424560X 4540 / 4500 PSI / 250’ COMPLETE

2424561X 7230 / 7250 PSI / 250’ COMPLETE

2412275K 4540 / 4500 PSI

2412277K 7230 / 7250 PSI

2424560K 4540 / 4500 PSI / 250’ COMPLETE

2424561K 7230 / 7250 PSI / 250’ COMPLETE

* All 49-State models use Honda engine P/N 2434485.

All 50-State models with “X” sux use Honda engine

P/N 980-340.

All 50-State models with “K” sux use Kohler engine

P/N 2441285A.

2

ORIGINAL OPERATING MANUAL HYDRA X

Warning!

Attention: Danger of injury by injection!

Airless units develop extremely high spraying pressures.

Be safety conscious!

1

2

3

Never put your ngers, hands or any other parts of the body into

the spray jet!

Never point the spray gun at yourself, other persons or animals.

Never use the spray gun without safety guard.

Do not treat a spraying injury as a harmless cut. In case of injury

to the skin through coating materials or solvents, consult a doctor

immediately for quick and expert treatment. Inform the doctor

about the coating material or solvent used.

The operating instructions state that the following points must

always be observed before starting up:

1. Faulty units must not be used.

2. Secure spray gun using the trigger lock on the trigger.

3. Ensure that the unit is properly earthed.

4. Check allowable operating pressure of high-pressure hose and spray gun.

5. Check all connections for leaks.

The instructions regarding regular cleaning and maintenance of

the unit must be strictly observed.

Before any work is done on the unit or for every break in work the

following rules must be observed:

1. Release the pressure from spray gun and hose.

2. Secure the spray gun using the trigger lock on the trigger.

3. Switch o unit.

3

CONTENTS

HYDRA X

1 SAFETY REGULATIONS FOR AIRLESS

SPRAYING ______________________________ 4

1.1 Explanation of symbols used _____________________4

1.2 Safety hazards ________________________________4

1.3 Setup on an uneven surface _____________________6

1.4 Gasoline engine safety__________________________7

1.5 Fueling (gas engine) ___________________________7

2 MAIN AREAS OF APPLICATION ____________ 8

2.1 Application ___________________________________ 8

2.2 Coating materials ______________________________ 8

3 DESCRIPTION OF UNIT ___________________ 9

3.1 Airless process ________________________________9

3.2 Instruction manuals list _________________________9

3.3 Functioning of the unit _________________________9

3.4 System diagram ______________________________10

3.5 Technical data _______________________________11

3.6 Transportation _______________________________12

3.7 Electronic controls ____________________________12

4 OPERATION ____________________________ 13

4.1 Setup ______________________________________13

4.2 Starting the engine ___________________________14

4.3 Preparing a new sprayer _______________________15

4.4 Preparing to spray ____________________________15

4.5 55-gallon drum setup _________________________16

4.6 Spraying ____________________________________17

4.7 Pressure relief procedure _______________________17

5 SPRAYING TECHNIQUE __________________ 18

5.1 Cleaning a clogged tip _________________________18

5.2 Interruption of work __________________________19

5.3 Handling the high pressure hose ________________19

6 CLEANUP ______________________________ 20

6.1 Special cleanup instructions for use with

ammable solvents ___________________________20

6.2 Cleaning the sprayer __________________________20

6.3 Parking procedure ____________________________20

6.4 Cleaning the outside of the unit _________________21

6.5 Cleaning the lter screen _______________________21

6.6 Cleaning the airless spray gun __________________21

7 MAINTENANCE _________________________ 22

7.1 Daily maintenance ____________________________22

7.2 Lubricating the upper packings _________________22

7.3 Maintaining the hydraulic system ________________ 22

7.4 Maintaining the uid section ___________________23

7.5 High pressure hose ___________________________23

7.6 Basic engine maintenance______________________24

8 TROUBLESHOOTING ____________________ 25

8.1 Airless gun __________________________________25

8.2 Fluid section _________________________________25

8.3 Hydraulic motors _____________________________26

8.4 Lift assembly ________________________________26

8.5 Spray patterns _______________________________27

WARRANTY _________________________________ 80

4

SAFETY PRECAUTIONS HYDRA X

1 SAFETY REGULATIONS FOR AIRLESS

SPRAYING

1.1 EXPLANATION OF SYMBOLS USED

This manual contains information that must be read and

understood before using the equipment. When you come to

an area that has one of the following symbols, pay particular

attention and make certain to heed the safeguard.

This symbol indicates a potential hazard

that may cause serious injury or loss of life.

Important safety information will follow.

At

tention

This symbol indicates a potential hazard

to you or to the equipment. Important

information that tells how to prevent

damage to the equipment or how to avoid

causes of minor injuries will follow.

Danger of skin injection

Danger of re from solvent and paint fumes

Danger of explosion from solvent, paint

fumes and incompatible materials

Danger of injury from inhalation of harmful

vapors

Danger of injury from electric shock

i

Notes give important information which

should be given special attention.

WARNING! CALIFORNIA

PROPOSITION 65 WARNING

This product can expose you to chemicals

including lead, which are known to the

State of California to cause cancer, birth

defects, or other reproductive harm.

The engine exhaust from models with gas-

powered engines can expose you to carbon

monoxide which is known to the State of

California to cause cancer, birth defects,

and other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

1.2 SAFETY HAZARDS

i

IMPORTANT SAFETY INSTRUCTIONS.

SAVE THESE INSTRUCTIONS.

WARNING: INJECTION INJURY

A high pressure stream produced by this

equipment can pierce the skin and underlying

tissues, leading to serious injury and possible

amputation.

Do not treat a spraying injury as a harmless cut. In

case of injury to the skin through coating materials

or solvents, consult a doctor immediately for

quick and expert treatment. Inform the doctor

about the coating material or solvent used.

PREVENTION:

• NEVER aim the gun at any part of the body.

• NEVER allow any part of the body to touch the uid stream.

DO NOT allow body to touch a leak in the uid hose.

• NEVER put your hand in front of the gun. Gloves will not

provide protection against an injection injury.

• ALWAYS lock the gun trigger, shut the uid pump o and

release all pressure before servicing, cleaning the tip guard,

changing tips, or leaving unattended. Pressure will not be

released by turning o the engine. The PRIME/SPRAY valve

or pressure bleed valve must be turned to their appropriate

positions to relieve system pressure.

• ALWAYS keep tip guard in place while spraying. The tip

guard provides some protection but is mainly a warning

device.

• ALWAYS remove the spray tip before ushing or cleaning

the system.

• NEVER use a spray gun without a working trigger lock and

trigger guard in place.

• All accessories must be rated at or above the maximum

operating pressure range of the sprayer. This includes

spray tips, guns, extensions, and hose.

5

SAFETY PRECAUTIONS

HYDRA X

WARNING: HIGH PRESSURE HOSE

The paint hose can develop leaks from wear,

kinking and abuse. A leak can inject material into

the skin. Inspect the hose before each use.

PREVENTION:

• Avoid sharp bending or kinking of the high-pressure hose.

The smallest bending radius amounts to about 20 cm.

• Do not drive over the high-pressure hose. Protect against

sharp objects and edges.

• Replace any damaged high-pressure hose immediately.

• Never repair damaged high-pressure hoses yourself!

• Electrostatic charging of spray guns and the high-pressure

hose is discharged through the high-pressure hose. For this

reason the electric resistance between the connections of

the high-pressure hose must be equal to or lower than

1M.

• For reasons of function, safety and durability use only

original Titan high-pressure hoses.

• Before each use, check all hoses for cuts, leaks, abrasion

or bulging of cover. Check for damage or movement of

couplings. Immediately replace the hose if any of these

conditions exist. Never repair a paint hose. Replace it with

another earthed high-pressure hose.

• Make sure power cord, air hose and spray hoses are routed

in such a manner to minimize slip, trip and fall hazard.

• Do not expose the hose to temperatures or pressures in

excess of those specied by the manufacturer.

• Do not use the hose as a strength member to pull or lift the

equipment.

WARNING: EXPLOSION OR FIRE

Flammable vapors, such as solvent and paint

vapors, in work area can ignite or explode.

PREVENTION:

• Use equipment only in well ventilated area. Keep a good

supply of fresh air moving through the area to keep the air

within the spray area free from accumulation of ammable

vapors. Keep pump assembly in well ventilated area. Do

not spray pump assembly.

• Gas models only - Do not ll fuel tank while engine is

running or hot; shut o engine and allow to cool. Fuel is

ammable and can ignite or explode if spilled on a hot

surface.

• Eliminate all ignition sources, such as pilot lights, cigarettes,

portable electric lamps and plastic drop cloths (potential

static arc).

• Keep work area free of debris, including solvent, rags and

gasoline.

• Do not plug or unplug power cords, or turn power or light

switches on or o when ammable vapors are present.

• Ground equipment and conductive objects in work

area. Make sure the grounding cable (not equipped) is

connected from the grounding lug to a true earth ground.

• Use only grounded hoses.

• Hold spray gun rmly to the side of a grounded pail when

triggering into pail.

• If there is static sparking or if you feel a shock, stop

operation immediately.

• Know the contents of the paint and solvents being sprayed.

Read all material Safety Data Sheets (SDS) and container

labels provided with the paints and solvents. Follow the

paint and solvent manufacturer’s safety instructions.

• Do not use a paint or solvent containing halogenated

hydrocarbons. Such as chlorine, bleach, mildewcide,

methylene chloride and trichloroethane. They are not

compatible with aluminum. Contact the coating supplier

about compatibility of material with aluminum.

• Keep a re extinguisher in work area.

6

SAFETY PRECAUTIONS HYDRA X

WARNING: HAZARDOUS VAPORS

Paints, solvents, and other materials can be

harmful if inhaled or come in contact with body.

Vapors can cause severe nausea, fainting, or

poisoning.

PREVENTION:

• Wear respiratory protection when spraying. Read all

instructions supplied with the mask to be sure it will

provide the necessary protection.

• All local regulations regarding protection against

hazardous vapors must be observed.

• Wear protective eyewear.

• Protective clothing, gloves and possibly skin protection

cream are necessary for the protection of the skin. Observe

the regulations of the manufacturer concerning coating

materials, solvents and cleaning agents in preparation,

processing and cleaning units.

WARNING: GENERAL

This product can cause severe injury or property

damage.

PREVENTION:

• Follow all appropriate local, state, and national codes

governing ventilation, re prevention, and operation.

• Pulling the trigger causes a recoil force to the hand that is

holding the spray gun. The recoil force of the spray gun

is particularly powerful when the tip has been removed

and high pressure has been set on the airless pump. When

cleaning without a spray tip, set the pressure control knob

to the lowest pressure.

• Use only manufacturer authorized parts. User assumes all

risks and liabilities when using parts that do not meet the

minimum specications and safety devices of the pump

manufacturer.

• ALWAYS follow the material manufacturer’s instructions

for safe handling of paint and solvents.

• Clean up all material and solvent spills immediately to

prevent slip hazard.

• Wear ear protection. This unit can produce noise levels

above 85 dB(A).

• Never leave this equipment unattended. Keep away from

children or anyone not familiar with the operation of airless

equipment.

• Do not spray on windy days.

• The device and all related liquids (i.e. hydraulic oil) must be

disposed of in an environmentally friendly way.

• Stay alert and watch what you are doing.

• Do not operate the unit when fatigued or under the

inuence of drugs or alcohol.

• Do not overreach or stand on an unstable support. Keep

eective footing and balance at all times.

1.3 SETUP ON AN UNEVEN SURFACE

The front end must always point downwards in order to avoid

sliding away.

If possible do not use the unit on an inclined surface since the

unit tends to wander due to the resulting vibrations.

7

SAFETY PRECAUTIONS

HYDRA X

1.4 GASOLINE ENGINE SAFETY

1. Gas engines are designed to give safe and dependable

service if operated according to instructions. Read and

understand the engine manufacturer’s Owner’s Manual

before operating the engine. Failure to do so could result

in personal injury or equipment damage.

2. To prevent re hazards and to provide adequate

ventilation, keep the engine at least 1 meter (3 feet) away

from buildings and other equipment during operation. Do

not place ammable objects close to the engine.

3. People who are not operating the device must stay away

from the area of operation due to a possibility of burns from

hot engine components or injury from any equipment the

engine may be used to operate.

4. Know how to stop the engine quickly, and understand the

operation of all controls. Never permit anyone to operate

the engine without proper instructions.

5. Gasoline is extremely ammable and is explosive under

certain conditions.

6. Refuel in a well-ventilated area with the engine stopped.

Do not smoke or allow ames or sparks in the refueling

area or where gasoline is stored.

7. Do not overll the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

8. Be careful not to spill fuel when refueling. Fuel vapor or

spilled fuel may ignite. If any fuel is spilled, make sure the

area is dry before starting the engine.

9. Never run the engine in an enclosed or conned area.

Exhaust contains poisonous carbon monoxide gas;

exposure may cause loss of consciousness and may lead

to death.

10. The muer becomes very hot during operation and

remains hot for a while after stopping the engine. Be

careful not to touch the muer while it is hot. To avoid

severe burns or re hazards, let the engine cool before

transporting it or storing it indoors.

11. Never ship/transport sprayer with gasoline in the tank.

1.5 FUELING GAS ENGINE

Gasoline is extremely ammable and is explosive

under certain conditions.

FUEL SPECIFICATIONS

Use automotive gasoline that has a pump octane number of 86

or higher, or that has a research octane number of 91 or higher.

Use of a lower octane gasoline can cause persistent “pinging” or

heavy “spark knock” (a metallic rapping noise) which, if severe,

can lead to engine damage.

i

If “spark knock” or “pinging” occurs at a steady

engine speed under normal load, change brands

of gasoline. If spark knock or pinging persists,

consult an authorized dealer of the engine

manufacturer. Failure to do so is considered

misuse, and damage caused by misuse is not

covered by the engine manufacturer’s limited

warranty.

Occasionally you may experience light spark

knock while operating under heavy loads. This

is no cause for concern, it simply means your

engine is operating eciently.

• Unleaded fuel produces fewer engine and spark plug

deposits and extends the life of the exhaust system

components.

• Never use stale or contaminated gasoline or an oil/gasoline

mixture. Avoid getting dirt, dust, or water in the fuel tank.

GASOLINES CONTAINING ALCOHOL

If you decide to use a gasoline containing alcohol (gasohol), be

sure its octane rating is at least as high as that recommended

by the engine manufacturer. There are two types of “gasohol”:

one containing ethanol, and the other containing methanol.

Do not use gasohol that contains more than 10% ethanol. Do

not use gasoline containing methanol (methyl or wood alcohol)

that does not also contain co-solvents and corrosion inhibitors

for methanol. Never use gasoline containing more than 5%

methanol, even if it has co-solvents and corrosion inhibitors.

i

Fuel system damage or engine performance

problems resulting from the use of fuels that

contain alcohol is not covered under the

warranty. The engine manufacturer cannot

endorse the use of fuels containing methanol

since evidence of their suitability is incomplete

at this time.

Before buying gasoline from an unfamiliar

station, try to nd out if the gasoline contains

alcohol. If it does, conrm the type and

percentage of alcohol used. If you notice any

undesirable operating characteristics while using

a gasoline that contains alcohol, or one that you

think contains alcohol, switch to a gasoline that

you know does not contain alcohol.

8

MAIN AREAS OF APPLICATION HYDRA X

2 MAIN AREAS OF APPLICATION

2.1 APPLICATION

The main area of application are thick layers of highly viscous

coating material for large areas and a high consumption of

material.

Priming and nal coating of large areas, sealing, impregnation,

construction sanitation, façade protection and renovation, rust

protection and building protection, roof coating, roof sealing,

concrete sanitation, as well as heavy corrosion protection.

EXAMPLES OF OBJECTS TO BE SPRAYED

Large-scale construction sites, cooling towers, bridges, sewage

treatment plants and terraces.

DO NOT use this equipment to spray water or

acid.

At

tention

Do not lift by cart handle when loading or

unloading.

Device is very heavy. Three-person lift is required.

FLUID PUMP

The HYDRA X uid pump is mounted to a lift mechanism that

can be automatically raised or lowered based on the container

from which material is being drawn.

i

The inlet lter (rock catcher) on the bottom of

the suction tube will need to be removed when

drawing material from a sealed drum.

2.2 COATING MATERIALS

PROCESSIBLE COATING MATERIALS

Diluting lacquers and paints or those containing solvents, two-

component coating materials, dispersion and latex paints.

No other materials should be used for spraying without Titan‘s

approval.

i

Pay attention to the Airless quality of the coating

materials to be processed.

VISCOSITY

The unit is able to process coating materials with up to

65,000 mPas. If highly viscous coating materials cannot be taken

in or the performance of the unit is too low, the paint must be

diluted in accordance with the manufacturer‘s instructions.

i

Attention: Make sure, when stirring up with

motor-driven agitators that no air bubbles are

stirred in. Air bubbles disturb when spraying and

can, in fact, lead to interruption of operation.

COATING MATERIALS WITH ABRASIVE MATERIALS

These particles have a strong wear and tear eect on valves and

tips, but also on the spray gun. This impairs the durability of

these wearing parts considerably.

TWOCOMPONENT COATING MATERIAL

The appropriate processing time must be adhered to exactly.

Within this time rinse through and clean the unit meticulously

with the appropriate cleaning agents.

FILTERING

This unit is not equipped with a high-pressure outlet lter.

However, a high pressure outlet ter kit can be purchased

separately if desired.

All compatible accessories for this unit are listed in the online

service manual, Form No. 2412594, available for download at

www.titantool.com.

9

DESCRIPTION OF UNIT

HYDRA X

3 DESCRIPTION OF UNIT

3.1 AIRLESS PROCESS

A piston pump takes in the coating material by suction and

conveys it to the tip. Pressed through the tip at a pressure of

up to a maximum of 4500 PSI (310 bar, 31 MPa) or 7250 PSI

(500 bar, 50 MPa), the coating material is atomized. This high

pressure has the eect of micro ne atomization of the coating

material.

As no air is used in this process, it is described as an AIRLESS

process.

This method of spraying has the advantages of nest

atomization, cloudless operation and a smooth, bubble-free

surface. As well as these, the advantages of the speed of work

and convenience must be mentioned.

3.2 INSTRUCTION MANUALS LIST

The following is a list of the available instruction manuals for

this unit.

Online items can be downloaded at www.titantool.com

FORM # DESCRIPTION HOW TO FIND

2412595 Operation Manual

(EN/FR/ES)

• included with unit

• online

2412594 Service manual, spare

parts, accessories

(EN/FR/ES)

• online

3.3 FUNCTIONING OF THE UNIT

The following section contains a brief description of the

technical construction for better understanding of the function

of the unit.

TITAN HYDRA X are high-pressure spraying units driven by a

gasoline engine.

The gasoline engine (g. 1, item 1) drives the hydraulic pump

(3) by means of a timing belt which is under the belt cover (2).

Hydraulic oil ows to the hydraulic motor (4) and then moves

the piston up and down in the material feed pump (5).

The inlet valve is opened automatically by the upwards

movement of the piston. The outlet valve is opened when the

piston moves downward.

The coating material ows under high pressure through the

high-pressure hose to the spray gun. When the coating material

exits from the tip it atomizes.

The pressure control knob (6) controls the volume and the

operating pressure of the coating material.

4

5

1

3

6

2

10

14

15

6

8

9

11

13

12

7

3

4

5

1

2

10

DESCRIPTION OF UNIT HYDRA X

3.4 SYSTEM DIAGRAM

1. Handle

2. Pressure control knob

3. Gasoline engine

4. Engine key ignition

5. Suction tube storage

6. Hydraulic motor

7. Oil measuring stick

8. Oil cup for Piston Lube

(Piston Lube prevents increased

wear and tear of the packings)

9. Pressure gauge

10. High-pressure hose outlet

11. Relief valve:

Turn left for circulation k

Turn right for spray p

12. Master power switch

13. Lift switch

14. Bleed hose

15. Suction tube

11

DESCRIPTION OF UNIT

HYDRA X

3.5 TECHNICAL DATA

4500 PSI 7250 PSI

Gasoline engine, power

Honda 389cc, 11.7 Hp,

8.7 kW 389cc, 11.7 Hp,

8.7 kW

Kohler 429cc, 14 Hp,

10.5 kW 429cc, 14 Hp,

10.5 kW

Fuel Capacity

1.6 US gal (6.06 l) 1.6 US gal (6.06 l)

Max. operating pressure

4500 PSI 7250 PSI

Max. sound pressure level

98 dB (A)* 98 dB (A)*

Max. size of tip with a spray gun

1-gun 0.067” – 1.70 mm 0.065” – 1.65 mm

2-gun 0.041” – 1.04 mm 0.035” – 0.89 mm

3-gun 0.035” – 0.89 mm 0.028” – 0.71 mm

4-gun 0.031” – 0.79 mm 0.025” – 0.63 mm

5 gun 0.029” – 0.73 mm 0.021” – 0.53 mm

6 gun 0.025” – 0.63 mm

Max. volume ow

4.0 gal (15.1 l)/min 2.8 gal (10.6 l)/min

Weight

390 lbs (177 kg) 390 lbs (177 kg)

Suction system

Siphon tube Siphon tube

Max. viscosity

65,000 mPa·s 65,000 mPa·s

Dimensions L x W x H

48” x 32” x 52” 48” x 32” x 52”

Max. temperature of the coating material

109ºF (43° C) 109ºF (43° C)

Hydraulic oil lling quantity

22.7 l (6.0 gal) 22.7 l (6.0 gal)

Max. tire pressure

0.2 MPa (2 bar, 30

PSI) 0.2 MPa (2 bar, 30

PSI)

* Place of measurement: 1 m distance from unit and 1.60

m above reverberant oor, 120 bar (12 MPa) operating

pressure.

OPERATING TEMPERATURE

This equipment will operate correctly in its intended ambient,

at a minimum between +50ºF (10°C) and 104ºF (+40°C).

RELATIVE HUMIDITY

The equipment will operate correctly within an environment

at 50% RH, 104ºF (+40°C). Higher RH may be allowed at lower

temperatures.

Measures shall be taken by the Purchaser to avoid the harmful

eects of occasional condensation.

ALTITUDE

This equipment will operate correctly up to 2100 m above

mean sea level.

Contact your local Honda or Kohler representative for operating

the unit above 2100m above mean sea level.

TRANSPORTATION AND STORAGE

This equipment will withstand, or has been protected against,

transportation and storage temperatures of -13ºF (-25°C) to

131ºF (+55°C) and for short periods up to 150ºF (+70°C).

Fluid pump should be stored in glycol below 32ºF (0ºC).

It has been packaged to prevent damage from the eects of

normal humidity, vibration and shock.

12

DESCRIPTION OF UNIT HYDRA X

3.6 TRANSPORTATION

TRANSPORTATION IN VEHICLE

Secure the unit with a suitable fastening.

CRANE TRANSPORT

Hanging points for crane straps or ropes, see gure 3 below.

The motor/pump lift should be in the fully retracted (down)

position before lifting the unit.

i

The machine weighs approximately 390 pounds.

Follow relevant OSHA standards for lifting.

www.osha.gov

Make sure the strap or rope is behind the

hydraulic tube (located on the right front of

the unit, when facing the front) so that it is not

crushed.

3.7 ELECTRONIC CONTROLS

MASTER POWER SWITCH

The master power switch provides electrical power to the

entire system. Press and hold the button for 3 seconds to turn

electrical power ON. Press the button once to turn electrical

power OFF.

LIFT SWITCH

The lift switch raises and lowers the hydraulic motor/uid

section of the unit. The master power switch must be switched

ON in order for the lift switch to be functional.

If the lift switch is held in the UP position for three seconds (and

then released) the lift mechanism will automatically extend to

the highest position and then stop, or the operator can push

the switch down to keep the lift from going up any further.

The lift can push the tube far enough to lift the front of the

machine. This will not damage the machine.

ENGINE KEY IGNITION

The engine key ignition switches the engine ON and OFF. Turn

the key all the way to the right to turn on the engine whenever

prompted.

13

OPERATION

HYDRA X

4 OPERATION

This equipment produces a uid stream at

extremely high pressure. Read and understand

the warnings in the Safety Precautions section

at the front of this manual before operating this

equipment.

4.1 SETUP

1. Turn the master power switch ON (I).

2. Press and hold the ‘UP’ (G) on the lift switch for three

seconds to raise the hydraulic motor/uid pump assembly.

Release the switch after three seconds and the lift wil

automatically raise to its highest position and then stop.

3. Open (pull apart) the two brass clasps on the top of the

suction tube assembly (Fig. 5, item 1).

4. Mount the suction tube (2) over the uid pump (3).

5. Close the two clasps to secure the suction tube. Insert

the locking clips (not shown) to lock the coupler clasps in

place.

1

3

2

6. Make sure the bleed hose (Fig. 6, item 1) is threaded into

the bleed valve (2). It has factory installed blue thread

locker on the tting and should be tightened wrench tight.

7. Attach a minimum of 50’ (15 m) of nylon airless spray hose

(3) to the sprayer. Do not use PTFE tape or thread sealant

on the spray hose connection.

1

2

3

8. Attach an airless spray gun to the spray hose. Do not

attach the tip to the spray gun yet. Remove the tip if it is

already attached.

i

For multiple gun operation, connect the multiple

gun manifold to the single gun outlet (see

manifold kit 2414176 for details). Connect a hose

and gun to the desired number of outlets. Make

sure the unused gun outlets remain plugged.

See “Technical Data”, Section 3.5 to determine

number of guns and maximum spray tip sizes.

9. Fill the oil cup 1/2 full with Piston Lube (P/N 314-480).

This extends packing life. When using silicone, use part

number 91-36, throat seal lubricant.

At

tention

Piston Lube prevents increased wear and tear to

the packings.

10. Check the hydraulic uid level daily before starting the

sprayer. The hydraulic uid level should be between the

two notches on the dipstick. Refer to the Maintenance

section of this manual for hydraulic system maintenance

instructions.

At

tention

Use of Titan’s Coolo™ Hydraulic Fluid (P/N 430-

361) is mandatory in the hydraulic system. Do

not use any other hydraulic uid. Use of any

other hydraulic uid may seriously damage the

hydraulic system and will void the warranty.

11. Check the engine oil level daily before starting the sprayer.

The gasoline engine oil level is determined by the engine

manufacturer. Refer to the engine manufacturer’s service

manual supplied with this sprayer.

14

OPERATION HYDRA X

12. Make sure the sprayer is grounded/earthed. All sprayers are

equipped with a grounding/earthing lug. A grounding/

earthing cable should be used to connect the sprayer to a

true earth ground. Check your local electrical regulations

for detailed grounding/earthing instructions.

Proper grounding/earthing is important. The

passage of some materials through the nylon

uid hose will build up a static electric charge,

which if discharged, could ignite solvent vapors

present and create an explosion.

13. Strain all paints with a nylon strainer to ensure trouble

free operation and freedom from frequent cleaning of the

suction lter and gun lter.

14. Make sure the spray area is well ventilated to prevent

hazardous operation with volatile solvents or exhaust

fumes.

If lacquer or other ammable materials are to be

sprayed, ALWAYS locate the sprayer outside the

immediate spraying area. Failure to do so may

cause an explosion.

15. Locate the sprayer outside the immediate spraying area to

avoid clogged air intake of the engine with overspray.

4.2 STARTING THE ENGINE

i

Follow these instructions whenever prompted in

this manual to start the engine.

1. Move the fuel valve lever (Fig. 9, item 2) to the open

position.

2. Move the throttle lever (3) to its middle point.

3. Move the choke lever (4) to the closed position for a cold

engine or to the open position for a warm engine.

4. Turn the ignition key (1) to the ON position.

5. Pull the starter rope (5) briskly until the engine starts, or

turn the ignition key (1) all the way to the right until the

engine starts.

1

3

5

2

4

i

If choke lever (4) was moved to closed position to

start the engine, it must be opened again once

the engine is running.

15

OPERATION

HYDRA X

4.3 PREPARING A NEW SPRAYER

i

If this unit is new, it is shipped with test uid in

the uid section to prevent corrosion during

shipment and storage. This uid must be

thoroughly cleaned out of the system with

mineral spirits before you begin spraying.

At

tention

Always keep the trigger lock on the spray gun in

the locked position while preparing the system.

Refer to the spray gun instruction manual for

trigger lock instructions.

1. Lower the siphon tube into a container of mineral spirits.

2. Place the bleed hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to

its lowest pressure setting (Fig. 10, item 1).

4. Open the bleed valve (2) by turning it fully counterclockwise.

1

2

5. Start the engine (see section 4.2).

6. Turn the master power switch ON (I).

7. Turn the pressure control knob (g. 10, item 1) clockwise

approximately 1/3 of the way to increase pressure until

the sprayer cycles evenly and solvent ows freely from the

bleed hose.

8. Allow the sprayer to run for 15–30 seconds to ush the

test uid out through the bleed hose and into the waste

container.

9. Turn o the sprayer.

• set the pressure to minimum by turning the pressure

control knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

4.4 PREPARING TO SPRAY

i

Before spraying, it is important to make sure that

the uid in the system is compatible with the

paint that is going to be used.

Incompatible uids and paint may cause the

valves to become stuck closed, which would

require disassembly and cleaning of the sprayer’s

uid section.

At

tention

Always keep the trigger lock on the spray gun in

the locked position while preparing the system.

Refer to the spray gun instruction manual for

trigger lock instructions.

1. Lower the siphon tube into a container of mineral spirits.

2. Place the bleed hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to

its lowest pressure setting (Fig. 10, item 1).

4. Open the bleed valve (2) by turning it fully counterclockwise.

5. Start the engine (see section 4.2).

6. Turn the master power switch ON (I).

7. Turn the pressure control knob (Fig. 10, item 1) clockwise

approximately 1/3 of the way to increase pressure until

the sprayer cycles evenly and solvent ows freely from the

bleed hose.

8. Allow the sprayer to run for 15–30 seconds to ush the uid

out through the bleed hose and into the waste container.

9. Turn o the sprayer.

• set the pressure to minimum by turning the pressure

control knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

i

Make sure that the spray gun does not have a tip

or tip guard installed.

10. Close the bleed valve by turning it fully clockwise.

11. Start the engine (see section 4.2).

12. Turn the master power switch ON (I).

13. Turn the pressure control knob clockwise approximately

1/3 of the way down to increase pressure.

14. Unlock the gun by turning the gun trigger lock to the

unlocked position.

16

OPERATION HYDRA X

Ground/Earth the gun by holding it against

the edge of the metal container while ushing.

Failure to do so may lead to a static electric

discharge, which may cause a re.

15. Trigger the gun into the metal waste container until the

old solvent is gone and fresh solvent is coming out of the

gun.

16. Lock the gun by turning the gun trigger lock to the locked

position (refer to spray gun manual).

17. Set down the gun and increase the pressure by turning

the pressure control knob slowly clockwise to its highest

setting.

18. Check the entire system for leaks. If leaks occur, turn the

sprayer o and follow the “Pressure Relief Procedure” in

this manual before tightening any ttings or hoses.

19. Follow the “Pressure Relief Procedure” (section 4.7) in this

manual before changing from solvent to paint.

Be sure to follow the Pressure Relief Procedure

when shutting the unit down for any purpose,

including servicing or adjusting any part of the

spray system, changing or cleaning spray nozzles,

or preparing for cleanup.

4.5 55GALLON DRUM SETUP

i

Follow these steps when drawing material from

a 55-gallon drum.

1. Make sure the sprayer is shut o and relieved of all pressure

(follow Pressure Relief Procedure, section 4.7).

2. Make sure the suction tube is not attached to the uid

pump. If attached, release the brass clamps and remove

the suction tube from the uid pump.

3. Turn the master power switch ON (l).

4. Press and hold the ‘UP’ (G) on the lift switch for three

seconds to raise the hydraulic motor/uid pump assembly.

Release the switch after three seconds and the lift will

automatically raise to its highest position and then stop.

5. Position the bottom of the uid pump over the container.

If drawing from a sealed container, position the bottom of

the uid pump over the large bung hole.

i

The inlet lter (rock catcher) on the bottom of

the suction tube will need to be removed when

drawing material from a sealed drum. Unscrew it

from the tube.

6. Carefully lower the suction tube down into the material

and then lift it up and attach it to the bottom of the uid

pump (Fig. 11, inset). Secure it by closing the brass clamps.

7. Place the bleed tube into the material. Use the smaller

vent hole if using a sealed container.

17

OPERATION

HYDRA X

4.6 SPRAYING

1. Lower the siphon tube into a container of paint.

2. Place the bleed hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to

its lowest pressure setting (Fig. 10, item 1).

4. Open the bleed valve (2) by turning it fully counterclockwise.

5. Start the engine (see section 4.2).

6. Turn the master power switch ON (I).

7. Turn the pressure control knob (Fig. 10, item 1) clockwise

approximately 1/3 of the way down to increase pressure

until the sprayer cycles evenly and material ows freely

from the bleed hose.

8. Turn o the sprayer.

• set the pressure to minimum by turning the pressure

control knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

• turn the master power switch OFF (0)

9. Remove the bleed hose from the waste container and

place it into the container of paint.

10. Close the bleed valve by turning it fully clockwise.

11. Start the engine (see section 4.2).

12. Turn the master power switch ON (I).

13. Turn the pressure control knob clockwise approximately

1/3 of the way down to increase pressure.

14. Unlock the gun by turning the gun trigger lock to the

unlocked position.

Ground/Earth the gun by holding it against

the edge of the metal container while ushing.

Failure to do so may lead to a static electric

discharge, which may cause a re.

15. Trigger the gun into the metal waste container until all

air and solvent is ushed from the spray hose and paint is

owing freely from the gun.

16. Lock the gun by turning the gun trigger lock to the locked

position.

17. Turn o the sprayer.

• set the pressure to minimum by turning the pressure

control knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

• turn the master power switch OFF (0)

18. Attach tip guard and tip to the gun as instructed by the tip

guard or gun manuals.

POSSIBLE INJECTION HAZARD. Do not spray

without the tip guard in place. Never trigger the

gun unless the tip is in either the spray or the

unclog position. Always engage the gun trigger

lock before removing, replacing or cleaning tip.

19. Start the engine (see section 4.2).

20. Turn the master power switch ON (I).

21. Increase the pressure by turning the pressure control knob

slowly clockwise and test the spray pattern on a piece of

cardboard. Adjust the pressure control knob until the

spray from the gun is completely atomized.

i

Turning the pressure up higher than needed to

atomize the paint will cause premature tip wear

and additional overspray.

4.7 PRESSURE RELIEF PROCEDURE

Be sure to follow the Pressure Relief Procedure

when shutting the unit down for any purpose,

including servicing or adjusting any part of the

spray system, changing or cleaning spray nozzles,

or preparing for cleanup.

1. Lock the spray gun by turning the gun trigger lock to the

locked position.

2. Turn o the sprayer.

• set the pressure to minimum by turning the pressure

control knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

• turn the master power switch OFF (0)

3. Unlock the gun by turning the gun trigger lock to the

unlocked position (refer to spray gun manual).

4. Hold the metal part of the gun rmly to the side of a metal

waste container to ground/earth the gun and avoid a build

up of static electricity.

5. Trigger the gun to remove any pressure that may still be

in the hose.

6. Lock the gun by turning the gun trigger lock to the locked

position (refer to spray gun manual).

7. Place the bleed hose into the metal waste container.

8. Open the bleed valve by turning it fully counterclockwise.

18

SPRAYING TECHNIQUE HYDRA X

5 SPRAYING TECHNIQUE

Injection hazard. Do not spray without the tip

guard in place. NEVER trigger the gun unless the

tip is completely turned to either the spray or the

unclog position. ALWAYS engage the gun trigger

lock before removing, replacing or cleaning tip.

A) The key to a good paint job is an even coating over the

entire surface. Keep your arm moving at a constant speed

and keep the spray gun at a constant distance from the

surface. The best spraying distance is 10-12 inches (25 to

30 cm) between the spray tip and the surface.

25 - 30 cm

A

B) Keep the spray gun at right angles to the surface. This

means moving your entire arm back and forth rather than

just exing your wrist.

Keep the spray gun perpendicular to the surface,

otherwise one end of the pattern will be thicker than the

other.

B

C) Trigger gun after starting the stroke. Release the trigger

before ending the stroke. The spray gun should be

moving when the trigger is pulled and released. Overlap

each stroke by about 30%. This will ensure an even

coating.

25 - 30 cm25 - 30 cm

C

i

If very sharp edges result or if there are streaks in

the spray jet – increase the operating pressure or

dilute the coating material.

5.1 CLEANING A CLOGGED TIP

i

If the spray pattern becomes distorted or stops

completely while pulling the trigger, perform the

steps below.

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual, section 4.7.

2. Clear the spray tip per the instructions in the spray gun

operation manual.

The ow from the spray tip is at very high pressure.

Contact with any body part may be dangerous.

Do not place nger on gun outlet. Do not point

the gun at any person. Never operate the spray

gun without the proper tip guard.

19

SPRAYING TECHNIQUE

HYDRA X

5.2 INTERRUPTION OF WORK

i

Follow these steps if stopping work for up to 20

hours. Only follow these steps if you used latex -

or water-based spray materials.

i

If you are just simply swapping out material

containers, turn the pressure control knob fully

counterclockwise to minimum prior to changing

the material container.

Turn pressure control knob clockwise to previous

position when ready to resume spraying.

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual, section 4.7.

2. Place the spray gun in a plastic bag, or drop it into a bucket

of water.

3. Leave the suction tube and return hose immersed in

the coating material or immerse it into a corresponding

cleaning agent.

4. Cover the coating material with plastic and place unit in a

cool, shaded spot to keep material from drying out.

At

tention

If fast-drying or two-component coating material

is used, ensure that the unit is rinsed with a

suitable cleaning agent within the processing

time.

i

When ready to being spraying again, remove the

plastic from the material container and restart

the sprayer by following the steps in section 4.5.

5.3 HANDLING THE HIGHPRESSURE HOSE

All accessories must be rated at or above

the maximum operating pressure range of

the sprayer. This includes spray tips, guns,

extensions, and hose.

Danger of injury through leaking high-pressure

hose. Replace any damaged high-pressure hose

immediately.

Never repair damaged high-pressure hoses

yourself!

The high-pressure hose is to be handled with care. Avoid sharp

bends and folds: the smallest bending radius is about 8” (20 cm).

Do not drive over the high-pressure hose. Protect against sharp

objects and edges.

Never pull on the high-pressure hose to move the device.

Make sure that the high-pressure hose cannot twist. This can

be avoided by using a Titan spray gun with a swivel joint and

hose system.

i

When using the high-pressure hose while

working on scaolding, it is best to always guide

the hose along the outside of the scaolding.

i

The risk of damage rises with the age of the

high-pressure hose. Titan recommends replacing

high-pressure hoses after 6 years.

i

Use only Titan original-high-pressure hoses

in order to ensure functionality, safety and

durability.

20

CLEANUP HYDRA X

6 CLEANUP

At

tention

The sprayer, hose, and gun should be cleaned

thoroughly after daily use. Failure to do so

permits material to build up, seriously aecting

the performance of the unit.

Always spray at minimum pressure with the gun

nozzle tip removed when using mineral spirits

or any other solvent to clean the sprayer, hose,

or gun. Static electricity buildup may result in a

re or explosion in the presence of ammable

vapors.

6.1 SPECIAL CLEANUP INSTRUCTIONS FOR USE

WITH FLAMMABLE SOLVENTS

• Always ush spray gun preferably outside and at least one

hose length from spray pump.

• If collecting ushed solvents in a one gallon metal

container, place it into an empty ve gallon container, then

ush solvents.

• Area must be free of ammable vapors.

• Follow all cleanup instructions.

6.2 CLEANING THE SPRAYER

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual, section 4.7.

2. Remove the gun tip and tip guard and clean with a brush

using the appropriate solvent.

3. Place the siphon tube into a container of the appropriate

solvent.

At

tention

Use only compatible solvents when cleaning

out oil based enamels, lacquers, coal tar, and

epoxies. Check with the uid manufacturer for

the recommended solvent.

4. Place the bleed hose into a metal waste container.

5. Set the pressure to minimum by turning the pressure

control knob fully counterclockwise.

6. Open the bleed valve by rotating the bleed valve handle

fully counterclockwise.

7. Start the engine (see section 4.2).

8. Turn the master power switch ON (I).

9. Allow the solvent to circulate through the sprayer and

ush the paint out of the bleed hose into the metal waste

container.

10. Close the bleed valve by rotating the bleed valve handle

fully clockwise.

Earth the gun by holding it against the edge of

the metal container while ushing. Failure to do

so may lead to a static electric discharge, which

may cause a re.

11. Trigger the gun into the metal waste container until the

paint is ushed out of the hose and solvent is coming out

of the gun.

12. Continue to trigger the spray gun into the waste container

until the solvent coming out of the gun is clean.

i

For long-term, cold weather storage, or any

freezing temperature exposure pump mineral

spirits through the entire system.

For short-term storage not exposed to freezing

temperatures when using latex paint, pump

water mixed with Titan Liquid Shield through

the entire system (see Accessories section of this

manual for part number and product label for

dilution instructions).

13. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual, section 4.7.

14. Store the sprayer in a clean, dry area.

At

tention

Do not store the sprayer under pressure.

6.3 PARKING PROCEDURE

i

Use this procedure when working with moisture

cured materials so no part of the uid section is

exposed to the environment which can cause

damage to the packings

1. Follow the “6.2 Cleaning the Sprayer” procedure

2. Push and hold the solenoid button until the piston reaches

fully down position (g. 11, item 1).

3. Continue to hold the solenoid button until the engine

stops turning.

4. Turn the engine key to the o position

5. Release the solenoid button.

La page charge ...

Titan Hydra X Manuel utilisateur

Titan Hydra X Manuel utilisateur

dans d''autres langues