Ariston AS5G1PMX/MEA Mode d'emploi

Catégorie
Fours
Taper
Mode d'emploi

Ce manuel convient également à

IS5G0PMW/MEAIS5G0PMW/MEAIS5G0PMW/MEAIS5G0PMW/MEA
Manuel
d’utilisation
Cuisinière pose-libre
Table des
matières
Consignes de sécurité
Installation
Manuel
d’utilisation
Manuel
d’utilisation
FR
Contents
Safety Instructions
Installation
Operating Instructions
COOKER AND OVEN
EN





AR
2
39
3
39
7
39
11
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
14
GUIDE D'UTILISATION QUOTIDIENNE
22
زﺎﻬﺠﻟا ﻒﺻو
36
GUIDEGUIDEGUIDE
39
3
14
39
3
14
39
7
22
39
7
22
39
11
36
39
11
36
EN
SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVED
These instructions are valid if the country
symbol appears on the appliance. If the symbol
does not appear on the appliance, please refer to
the technical instructions which will provide the
necessary instructions concerning modification of
the appliance to the conditions of use of the
country.
CAUTION : Use of the gas cooking appliance
results in the production of heat, moisture and
products of combustion in the room in which
it is installed. Ensure that the kitchen is well
ventilated, especially when the appliance is in
use: keep natural ventilation holes open or
install a mechanical ventilationdevice (mechanical
extractor hood). Prolonged intensive use of the
appliance may call for additional ventilation, such
asopening awindow, ormoreeffectiveventilation,
for example increasing the level of mechanical
ventilation (if possible).
Failure to follow the information in this manual exactly may cause a
fire or explosion, resulting in property damage or personal injury.
Before using the appliance, read these safety
instructions. Keep them nearby for future
reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all
times. The manufacturer declines any liability for
failure to observe these safety instructions, for
inappropriate use of the appliance or incorrect
setting of controls.
WARNING: The appliance and its accessible
parts become hot during use. Care shoul be taken
to avoid touching heating elements. Children less
than 8 years of age must be kept away unless
continuously supervised.
WARNING : If the hob surface is cracked, do not
use the appliance risk of electric shock.
WARNING : Danger of fire : Do not store items
on the cooking surfaces.
CAUTION : The cooking process has to be
supervised. A short cooking process has to be
supervised continuously.
WARNING: Leaving the hob unattended when
cooking with fat or oil can be dangerous risk of
fire. NEVER try to extinguish a fire with water, but
switch off the appliance and then cover the flames
e.g. with a lid or a fire blanket.
Do not use the hob as a work surface or support.
Keep clothes or other flammable materials away
from the appliance, unitl all the components have
cooled down completely - risk of fire.
Very young children (0-3 years) should be kept
away from the appliance. Young children (3-8
years) should be kept away from the appliance
unless continuously supervised. Children from 8
years old and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge can use this appliance
only if they are supervised or have been given
instructions on safe use and understand the
hazards involved. Children must not play with the
appliance. Cleaning and user maintenance must
notbecarried out bychildren without supervision.
CAUTION : In case of hotplate glass breakage:-
shut immediately off all burners and any electrical
heating element and isolate the appliance from
the power supply; - do not touch the appliance
surface; -do not use the appliance
The glass lid can break in if it is heated up.
Turn off all the burners and the electric
plates before closing the lid. Do not shout
down lid when burner alight
WARNING: The appliance and its accessible
parts becomehotduringuse. Careshouldbetaken
to avoid touching heating elements. Children less
than 8 years of age must be kept away unless
continuously supervised.
Never leave the appliance unattended during
food drying. If the appliance is suitable for
probe usage, only use a temperature probe
recommended for this oven - risk of fire.
Keep clothes or other flammable materials
away from the appliance, until all the components
have cooled down completely - risk of fire. Always
be vigilant when cooking foods rich in fat, oil or
when adding alcoholic beverages - risk of fire. Use
oven gloves to remove pans and accessories. At
the end of cooking, open the door with caution,
allowing hot air or steam to escape gradually
before accessing the cavity - risk of burns. Do not
obstruct hot air vents at the front of the oven - risk
of fire.
Exercise caution when the oven door is in the
open or down position, to avoid hitting the door.
When you place the rack inside, make sure that
the stop is directed upwards and in the back of the
cavity.
The device shall not be operated for more 15 s. If
after 15s the burner has not lit, stop operating the
device and open the compartment door and/or
wait at least 1 min before attempting a further
ignition of the burner.
PERMITTED USE
CAUTION: The appliance is not intended to
be operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
This appliance is intended to be used in
household and similar applications such as: staff
kitchen areas in shops, offices and other working
environments; farm houses; by clients in hotels,
3
motels, bed & breakfast and other residential
environments.
No other use is permitted (e.g. heating rooms).
This appliance is not for professional use. Do
not use the appliance outdoors.
Do not store explosive or flammable
substances (e.g. gasoline or aerosol cans) inside or
near the appliance - risk of fire.
Use pots and pans with bottoms the same
width as that of the burners or slightly larger (see
specific table). Make sure pots on the grates do
not protrude beyond the edge of the hob.
Improper use of the grids can result in damage
to the hob: do not position the grids upside down
or slide them across the hob.
Do not let the burner flame extend beyond the
edge of the pan
Do not use : Cast iron griddles, ollar stones,
terracotta pots and pans. Heat diffusers such as
metal mesh, or any other types. Two burners
simultaneously for one receptacle (e.g. Fish
kettle).
Should particular local conditions of the delivered
gas make the ignition of burner difficult, it is
advisable to repeat the operation with the knob
turned to small flame setting.
In case of installation of a hood above the cooktop,
please refer to the hood instructions for the correct
distance.
The protective rubber feet on the grids represent
a chocking hazard for young children. After
removing the grids, please ensure that all the feet
are correctly fitted.
INSTALLATION
The appliance must be handled and installed
by two or more persons - risk of injury. Use
protective gloves to unpack and install - risk of
cuts.
The electrical and gas connections must
comply with local regulation.
Installation, including water supply (if any),
electrical connections and repairs must be carried
out by a qualified technician. Do not repair or
replaceanypart of the applianceunless specifically
statedin the usermanual. Keepchildren awayfrom
the installationsite. After unpacking the appliance,
make sure that it has not been damaged during
transport. In the event of problems, contact the
dealer or your nearest Aftersales Service. Once
installed, packaging waste (plastic, styrofoam
parts etc.) must be stored out of reach of
children - risk of suffocation. The appliance must
be disconnected from the power supply before
any installation operation - risk of electric shock.
During installation, make sure the appliance does
not damage the power cable - risk of fire or electric
shock. Only activate the appliance when the
installation has been completed.
WARNING : Modification of the appliance and
its method of installation are essential in order to
use the appliance safely and correctly in all the
additional countries
Use pressure regulators suitable for the gas
pressure indicated in the instruction.
The room must be equipped with an air
extraction system that expels any combustion
fumes.
The roommust also allow properair circulation,
as air is needed for combustion to occur normally.
The flow of air must not be less than 2 m³/h per
kW of installed power.
The air circulation system may take air directly
from the outside by means of a pipe with an inner
cross section of at least 100 cm²; the opening must
not be susceptible to blockages.
The system can also provide the air needed for
combustion indirectly, i.e. from adjacent rooms
fitted with air circulation tubes as described above.
However, these rooms must not be communal
rooms, bedrooms or rooms that may present a fire
hazard.
Liquid petroleum gas sinks to the floor as it
is heavier than air. Therefore, rooms containing
LPG cylinders must also be equipped with vents
to allow gas to escape in the event of a leak.
This means LPG cylinders, whether partially or
completely full, must not be installed or stored
in rooms or storage areas that are below ground
level (cellars, etc.). It is advisable to keep only the
cylinder being used in the room, positioned so
that it is not subject to heat produced by external
sources (ovens, fireplaces, stoves, etc. ) which
could raise the temperature of the cylinder above
50°C.
Should you find it difficult to turn the knobs for the burner, please
contact the After-sales Service, who can replace of the burner tap if
found to be faulty.
The openings use for the ventilation and dispersion of heat must never
be covered.
Carry out all cabinet cutting works before
fitting the appliance in place and remove all wood
chips and sawdust.
Do not remove the appliance from its polystyrene
foam base until the time of installation.
If the appliance is not installed above an oven,
a separator panel (not included) must be installed
in the compartment under the appliance.
Connection with rigid pipe (copper or steel):
If the gas pressure is different from the
recommended pressure, a suitable pressure
regulator must be fitted to the inlet pipe in
accordance with the current national regulations.
Use an appropriate cabinet to ensure that the
appliance operates properly: To install the oven
under the counter (see diagram) or in a kitchen
unit, the cabinet must have the dimensions as the
picture.
4
To ensure adequate ventilation, the back panel
of the cabinet must be removed. It is advisable
to install the oven so that it rests on two strips
of wood, or on a completely flat surface with an
opening of at least 45 x 560 mm as the picure.
Donotinstalltheappliancebehindadecorative
door - risk of fire.
If the appliance is installed under the worktop,
do not obstruct the minimum gap between the
worktop and the upper edge of the oven - risk of
burns.
if the range is placed on a base, it must be
leveled and fixed to the wall by the retention chain
provided, to prevent the appliance slipping from
the base.
WARNING: In order to prevent the appliance
from tipping, the retentionchainmust be installed.
Refer to the instructions for installation.
GAS CONNECTION
WARNING : Prior to installation, ensure that the
local distribution conditions (type of gas and gas
pressure) and the configuration of the appliance
are compatible.
Check that the pressure of the gas supply is
consistent with the values indicated in Table 1
(“Burner and nozzle specifications”).
WARNING : The configuration conditions of
this appliance are stated on the label (or data
plate).
WARNING : This appliance is not connected
to a combustion products evacuation device. It
must be installed and connected in accordance
with current installation regulations. Particular
attention must be paid to the relevant
requirements regarding ventilation.
If the appliance is connected to liquid gas,
the regulation screw must be fastned as tightly as
possible.
IMPORTANT : When the gas cylinder or gas
container is installed, it must be properly settled
(vertical orientation).
WARNING : This operation must be perfomed
by a qualified technician
Use only flexible or rigid metal hose for gas
connection.
Connection with a rigid pipe (copper or steel)
Connection to the gas system must be carried
out in such a way as not to place any strain of
any kind on the appliance. There is an adjustable
L-shaped pipe fitting on the appliance supply
ramp and this is fitted with a seal in order to
prevent leaks. The seal must always be replaced
after rotating the pipe fitting (the seal is provided
with the appliance). The gas supply pipe fitting is
a threaded 1/2 gas cylindrical male attachment.
Connecting a flexible jointless stainless steel
pipe to a threaded attachment
The gas supply pipe fitting is a threaded 1/2 gas
cylindrical male attachment. These pipes must
be installed so that they are never longer than
2000 mm when fully extended. Once connection
has been made, make sure that the flexible metal
pipe does not touch any moving parts and is not
compressed. Only use pipes and seals that comply
with current national regulations.
IMPORTANT : If a staineless steel hose is used,
it must be installed so as not touch any moving
part of the furniture (e.g.drawer). It must pass
thorugh an area where there are no obstructions
and where it is possible to inspect it across its
entire length.
Theappliance shouldbe connectedto themain
gas supply or to a gas cylinder in compliance with
the current national regulations. Before making
the connection, make sure that the appliance is
compatible with the gas supply you wish to use.
If it is not, follow the instructions indicated in the
paragraph "Adapting to different types of gas".
After connection to the gas supply, check for
leaks with soapy water. Light up the burners and
turn the knobs from max position 1* to minimum
position 2* to check flame stability.
Connection to the gas network or the gas
cylinder may be carryout using a flexible rubber
or steel hose, in accordance with current national
legislation.
ELECTRICAL WARNINGS
IMPORTANT: Information about current and
voltage consumption is provided on the rating
plate.
The rating plate is on the front edge of the
oven (visible when the door is open).
It must be possible to disconnect the appliance
from the power supply by unplugging it if
plug is accessible, or by a multi-pole switch
installed upstream of the socket in accordance
with the wiring rules and the appliance must
be earthed in conformity with national electrical
safety standards.
The power cable must be long enough to connect the appliance,
once fitted in its housing, to the main power supply. Do not pull the
power supply cable.
Do not use extension leads, multiple sockets
or adapters. The electrical components must not
be accessible to the user after installation. Do not
use the appliance when you are wet or barefoot.
Do not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must
be replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard -
risk of electric shock.
If the power cable needs to be replaced,
contact an authorised service centre.
5
WARNING: Ensure that the appliance is
switched off before replacing the lamp to avoid
the possibility of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment -
risk of electric shock.
Do not use harsh abrasive cleaners or metal
scrapers to clean the door glass since they can
scratch the surface, which may result in shattering
of the glass.
Do not use abrasive or corrosive products,
chlorine-based cleaners or pan scourers.
Make sure the appliance has cooled down
before cleaning or performing maintenance. - risk
of burns.
WARNING: Switch off the appliance before
replacing the lamp - risk of electric shock.
To avoid damaging the electric ignition device, do not use it when
the burners are not in their housing.
Wear protective gloves for cleaning and
maintenance.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol . The various parts of the packaging must therefore
be disposed of responsibly and in full compliance with local authority
regulations governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling
of household electrical appliances, contact your local authority, the
collection service for household waste or the store where you purchased
the appliance. This appliance is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health. The
symbol
on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection centre for the recycling of electrical
and electronic equipment.
ENERGY SAVING TIPS
Only preheat the oven if specified in the cooking table or your recipe. Use
dark lacquered or enamelled baking trays as they absorb heat better.
Use a pressure cooker to save even more energy and time.
DECLARATION OF CONFORMITY
This appliance meets Ecodesign requirements of European Regulation
66/2014 in compliance with the European standard EN 60350-1.
This appliance meets Ecodesign requirements of European Regulation
66/2014 in compliance with the European standard EN 60350-2.
This appliance meets Ecodesign requirements of European Regulation
66/2014 in compliance with the European standard EN 30-2-1
This appliance meets Ecodesign requirements of European Regulation
65/2014 in compliance with the European standard EN 15181.
6
FR
CONSIGNES DE SÉCURITÉ
IMPORTANT - À LIRE ET À RESPECTER
Ces directives s'appliquent si le symbole du
pays apparaît sur l'appareil. Si le symbole
du pays n'apparaît pas sur l'appareil, vous
devez vous référer aux consignes techniques
qui contiennent les instructions nécessaires
concernant la modification de l'appareil afin de se
conformer aux conditions d'utilisation du pays.
ATTENTION : L'utilisation d'appareil de cuisson
au gaz génère de la chaleur, de l'humidité,
et des produits de la combustion dans la
pièce dans laquelle il est installé. Assurez-
vous que la cuisine est bien aérée, surtout
lorsque vous utilisez l'appareil : gardez les
trous de ventilations ouverts ou installez un
dispositif de ventilation mécanique (hotte de
ventilation). Une utilisation intensive et prolongée
peut nécessiter une ventilation supplémentaire,
commeouvrirunefenêtre,oupourventilateur plus
efficace, augmenter la puissance de la ventilation
mécanique (si possible).
Le non-respect des informations figurant dans le présent manuel
peut provoquer un incendie ou une explosion, donnant lieu à des
dommages aux biens ou à des lésions personnelles.
Avant d’utiliser l’appareil, lire attentivement les
consignes de sécurité. Conservez-les à portée
pour consultation ultérieure.
Le présent manuel et l'appareil en question
contiennent des consignes de sécurité
importantes qui doivent être lues et observées
en tout temps. Le Fabricant décline toute
responsabilité si les consignes de sécurité ne sont
pas respectées, en cas de mauvaise utilisation
de l’appareil, ou d'un mauvais réglage des
commandes.
MISE EN GARDE : l’appareil et ses
pièces accessibles deviennent chaudes pendant
l’utilisation. Évitez tout contact avec les éléments
chauffants. Les enfants de moins de 8 ans doivent
être tenus à l'écart de l'appareil, à moins d'être
sous surveillance constante.
MISE EN GARDE : Ne pas utiliser la table de
cuisson si la surface est cassée ou fissurée - risque
de choc électrique.
MISE EN GARDE : Risque d'incendie : Ne rangez
aucun objet sur les surfaces de cuisson.
ATTENTION : La cuisson doit être supervisée.
Une cuisson de courte durée doit être supervisée
en tout temps.
MISE EN GARDE : Une cuisson sans surveillance
sur une table de cuisson contenant de la graisse
ou de l'huile peut s'avérer dangereuse - risque
d'incendie. N'essayez JAMAIS d'éteindre un feu
avec de l'eau, mais éteignez l'appareil puis couvrez
les flammes à l'aide d'un couvercle par ex. ou
d'une couverture antifeu.
N'utilisez pas la table de cuisson comme surface
de travail ou support. Gardez les vêtements et
autres matières inflammables loin de l’appareil
jusqu’à ce que toutes les composantes soient
complètement refroidies - un incendie pourrait se
déclarer.
Les enfants en bas âge (0-3 ans) doivent être
tenus à l'écart de l'appareil. Les jeunes enfants
(3-8 ans) doivent être tenus à l'écart de l'appareil
sauf s'ils se trouvent sous surveillance constante.
Les enfants âgés de 8 ans et plus, ainsi que
les personnes présentant des capacités physiques,
sensoriellesoumentales réduites, ou ne possédant
ni l'expérience ni les connaissances requises,
peuvent utiliser cet appareil seulement s'ils sont
supervisés, ou si une personne responsable leur
a expliqué l'utilisation sécuritaire et les dangers
potentiels de l'appareil. Ne laissez pas les enfants
jouer avec l'appareil. Les enfants ne doivent pas
nettoyer, ni procéder à l'entretien de l'appareil
sans surveillance.
ATTENTION : En cas de rupture du verre de la
plaque de cuisson : -éteignez immédiatement tous
les brûleurs et la résistance électrique, et coupez
l'alimentation électrique ; - veillez à ne pas toucher
la surface de l'appareil ; - n'utilisez pas l'appareil
Le couvercle en verre peut se casser s'il
est surchauffé. Coupez tous les brûleurs
et les plaques électriques avant de fermer
le couvercle. Ne fermez pas le couvercle
lorsqu'un brûleur est allumé
MISEEN GARDE: L'appareil,ainsiquesesparties
accessibles, peuvent atteindre une température
élevée lors de l'utilisation. Évitez tout contact avec
les éléments chauffants. Les enfants de moins de
8 ans doivent être tenus à l'écart de l'appareil, à
moins d'être sous surveillance constante.
Ne laissez jamais l'appareil sans surveillance
pendant le séchage des aliments. Si
une sonde peut être utilisée avec l’appareil,
utilisez uniquement la sonde de température
recommandée pour ce four - un incendie pourrait
se déclarer.
Gardez les vêtements et autres matières
inflammables loin de l’appareil jusqu’à ce que
toutes les composantes soient complètement
refroidies - un incendie pourrait se déclarer. Soyez
toujours vigilant lorsque vous faites cuire des
aliments riches en matière grasse, huile, ou lorsque
vous ajoutez de l’alcool - un incendie pourrait se
déclarer. Utilisez des gants pour retirer les plats
et les accessoires. À la fin de la cuisson, ouvrez
la porte avec soin pour permettre à l'air chaud
ou la vapeur de s'évacuer graduellement avant
d'accéder la cavité - vous pourriez vous brûler.
Évitez d’obstruer les évents d’air chaud à l’avant
du four un incendie pourrait se déclarer.
7
Prenez garde de ne pas frapper la porte du
four lorsque qu’elle est ouverte ou en position
abaissée.
Lorsque vous placez le panier à l'intérieur, assurez-
vous que la butée est vers le haut et à l'arrière de
la cavité.
L'appareil ne doit pas être utilisé pendant plus de
15 sec. Si, après 15 secondes, le brûleur ne s’est pas
allumé, arrêtez de faire fonctionner l’appareil et
ouvrez la porte du compartiment et / ou attendez
au moins 1 minute avant de tenter de rallumer le
brûleur.
UTILISATION AUTORISÉE
MISE EN GARDE : Cet appareil n'est pas
conçu pour fonctionner à l'aide d'un dispositif de
commutation externe, comme une minuterie ou
un système de télécommande.
Cet appareil est destiné à un usage domestique
et peut aussi être utilisé dans les endroits suivants
: cuisines pour le personnel dans les magasins,
bureaux et autres environnements de travail ; dans
les fermes; par les clients dans les hôtels, motels,
et autres résidences similaires.
Aucune autre utilisation n'est autorisée (p. ex.
pour chauffer des pièces).
Cet appareil n'est pas conçu pour un
usage professionnel. N'utilisez pas l'appareil en
extérieur.
N'entreposez pas de substances explosives ou
inflammables (p. ex. essence ou bombe aérosol) à
l'intérieur ou près de l'appareil - risque d'incendie.
Utilisez des ustensiles de cuisson dont le
fond dispose d'un diamètre égal ou légèrement
supérieur à celui du foyer (voir le tableau suivant).
Vérifiez que les ustensiles de cuisson ne dépassent
pas de la table de cuisson.
Une utilisation inappropriée des grilles peut
endommager la table de cuisson : ne positionnez
pas les grilles sens dessus dessous ou ne les faites
pas glisser sur la table de cuisson.
Ne laissez pas la flamme du brûleur dépasser le
bord de la casserole
N'utilisez pas : de plaques en fonte, de
pierres ollaires, d'ustensiles de cuisson en terre
cuite. de diffuseurs de chaleur comme des
mailles métalliques ou tout autre type. deux
brûleurs simultanément pour un seul récipient
(par exemple, une poissonnière).
si des conditions locales spéciales du gaz distribué
rendent l'allumage du brûleur difficile, il est
conseillé de répéter l'opération en plaçant le
bouton sur la position petite flamme.
Avant d'installer une hotte au-dessus de la
table de cuisson, veuillez vous référer au manuel
d'utilisation de la hotte qui spécifie les distances
adéquates.
Les pieds de protection en caoutchouc appliqués
sur les grilles sont une source de danger potentiel
pour les jeunes enfants. Après avoir enlevé
les grilles, assurez-vous que tous les pieds sont
correctement installés.
INSTALLATION
Deux personnes minimum sont nécessaires
pour déplacer et installer l'appareil - risque de
blessure. Utilisez des gants de protection pour
le déballage et l'installation de l'appareil - vous
risquez de vous couper.
Les branchements électriques et le
raccordement au gaz doivent être réalisés
conformément aux réglementations locales.
L'installation, incluant l'alimentation en eau
(selon le modèle), et les connexions électriques,
ainsi que les réparations, doivent être exécutées
par un technicien qualifié. Ne procédez à aucune
réparation ni à aucun remplacement de pièce
sur l'appareil autre que ceux spécifiquement
indiqués dans le guide d'utilisation. Gardez
les enfants à l'écart du site d'installation. Après
avoir déballé l'appareil, assurez-vous qu'il n'a pas
été endommagé pendant le transport. En cas
de problème, contactez votre revendeur ou le
Service Après-Vente le plus proche. Une fois
installé, gardez le matériel d'emballage (sacs en
plastique, parties en polystyrène, etc.) hors de
la portée des enfants - ils pourraient s'étouffer.
L'appareil ne doit pas être branché à l'alimentation
électrique lors de l'installation - vous pourriez
vous électrocuter. Au moment de l'installation,
assurez-vous que le câble d'alimentation n'est pas
endommagé par l'appareil - risque d'incendie ou
de choc électrique. Allumez l’appareil uniquement
lorsque l’installation est terminée.
MISEENGARDE:Lesmodificationssurl'appareil
et sur les méthodes d'installation sont essentielles
pour utiliser l'appareil de façon sécuritaire et
correctement dans tous les autres pays
Utiliser des régulateurs de pression adéquats
pour la pression de gaz indiquée dans les
directives.
La pièce doit être équipée d'un système
d'évacuation d'air qui expulse les fumées de
combustion.
La pièce doit aussi permettre une bonne
circulation d'air; l'air est nécessaire pour une
combustion normale. La circulation d'air doit
être au minimum de 2 m³/h par kW de puissance
installée.
Le système de circulation d'air peut prendre
l'air directementdel'extérieuren utilisant un tuyau
avecune sectiontransversaleintérieure d'aumoins
100 cm² ; l'ouverture ne doit pas être bloquée.
Le système peut aussi obtenir l'air nécessaire de
façon indirecte, p. ex. d'une pièce voisine munie
de tuyaux pour la circulation d'air comme décrit
plus haut. Cependant, ces pièces ne doivent pas
être une salle commune, une chambre à coucher,
ou une pièce qui présente un danger d'incendie.
8
Comme il est plus lourd que l'air, le gaz de
pétrole liquéfié reste au niveau du sol. Donc, les
pièces contenant des cylindres de GPL doivent
être équipées de bouches de ventilation qui
permettent au gaz de s'échapper en cas de
fuite. Cela signifie donc que les cylindres de GPL,
pleins ou partiellement remplis, ne doivent pas
être installés ou entreposés dans des pièces ou
entrepôts qui se trouvent sous le niveau du sol
(cave, etc.). Nous vous conseillons de garder dans
la pièce les cylindres utilisés seulement, placés de
façon à ne pas être affecté par la chaleur produite
pardessources externes(four, foyer, cuisinière)qui
pourrait faire monter la température du cylindre
au dessus de 50°C.
Si vous constatez que les boutons sont difficiles à tourner sur la cuisinière,
contactezleService après-vente, qui peut remplacer le robinet du brûleur
s'il s'avère défectueux.
Les ouvertures utilisées pour la ventilation et la diffusion de la chaleur ne
doivent jamais être obstruées.
Découpez le contour du meuble avant d'y
insérer l’appareil, et enlevez soigneusement les
copeaux et la sciure de bois.
Retirez l'appareil de sa base en mousse
de polystyrène uniquement au moment de
l'installation.
Si l'appareil n'est pas installé au-dessus d'un
four, un panneau séparateur (non compris) doit
être installé dans le compartiment sous l'appareil.
Connexion avec des tuyaux rigides (cuivre et acier)
:
Si la pression de gaz est différente de celle
recommandée, un régulateur de pression adéquat
doit être fixé au tuyau d'entrée conformément à la
réglementation nationale en vigueur.
Utiliser un meuble adapté pour vous assurer que
l'appareil fonctionne correctement : pour installer
le four sous le comptoir (voir le schéma) ou à
l'intérieur d'un bloc-cuisine, le meuble doit avoir
les dimensions indiquées sur l'illustration.
Pour permettre une ventilation adéquate, le
panneau arrière du meuble doit être enlevé. Il est
conseillé d'installer le four pour qu'il repose sur
deux planches de bois, ou sur une surface plate
avec une ouverture d'au moins 45 X 560 mm,
comme l'illustré.
N'installez pas l'appareil derrière une porte
décorative - un incendie pourrait se déclarer.
Si l'appareil est installé sous le plan de travail,
n’obstruez pas l'espace minimum entre le plan
de travail et le rebord supérieur du four - vous
pourriez vous brûler.
Si la grille est placée sur une base, elle doit
être nivelée et fixée à la paroi par la chaîne
de conservation fournie, pour éviter l'appareil en
glissant de la base.
MISE EN GARDE : Afin d'éviter l'appareil de
glisser, la chaîne de retenue doit être installée.
Consultez les instructions pour l'installation.
RACCORDEMENT AU GAZ
MISE EN GARDE : Avant l'installation, assurez-
vous que les conditions de distribution locale
(nature et pression du gaz) sont compatibles avec
les réglages de l'appareil.
Assurez-vous que l'alimentation de la pression
de gaz est conforme aux valeurs indiquées au
tableau 1 Caractéristiques du brûleur et de la
buse »).
MISE EN GARDE : Les conditions de
configuration de cet appareil sont indiquées sur
l'étiquette (ou la plaque signalétique).
MISEENGARDE :Cetappareil n'estpas raccordé
à un dispositif d'évacuation des fumées. Il doit
être installé et branché conformément aux normes
d'installation en vigueur. Faire particulièrement
attention aux normes d'aération.
Si l'appareil est branché à du gaz liquide, la
vis de réglage doit être fixée aussi fermement que
possible.
IMPORTANT : Lorsque le cylindre de gaz
ou le récipient de gaz est installé, il doit être
convenablement installé (orientation verticale).
MISE EN GARDE : Cette opération doit être
effectuée par un technicien spécialisé
Effectuez le raccordement au gaz à l'aide d'un
flexible ou d'un tuyau en métal rigide uniquement.
Connexion avec un tuyau rigide (cuivre et
acier)
Le branchement au système de gaz doit
être effectué de façon à ne pas affecter le
fonctionnement des autres appareils. La rampe de
distribution comprend un raccord de tuyauterie
en forme de L équipé d'un joint d'étanchéité
pour prévenir les fuites. Le joint d'étanchéité
doit toujours être remplacé lorsqu'on remplace
le raccord de tuyauterie ( le joint est fourni
avec l'appareil). Le raccord de tuyauterie de
l'alimentation de gaz est un raccord cylindrique
mâle avec un filament de 1/2.
Brancher un tuyau d'acier inoxydable flexible
et sans joint à un raccord fileté
Le raccord de tuyauterie de l'alimentation de gaz
est un raccord cylindrique mâle avec un filament
de 1/2. Ces tuyaux doivent être installés de
façon à ne pas dépasser 2000 mm de longueur
lorsqu'ils sont complètement étirés. Une fois le
branchement terminé, assurez-vous que le tuyau
flexible en métal ne touche pas aux pièces mobiles
et qu'il n'est pas écrasé. Utiliser seulement des
tuyaux et des joints d'étanchéité conforment à la
réglementation nationale.
IMPORTANT : Si vous utilisez un tuyau en acier
inoxydable, assurez-vous qu'il ne touche à aucune
pièce mobile du meuble (p. ex. un tiroir). Le tuyau
doit passer à travers un endroit libre d'obstruction
9
et il est possible de l'inspecter sur toute sa
longueur.
L'appareil doit être branché à l'alimentation
principale ou à un cylindre de gaz conformément
à la réglementation nationale. Avant d'effectuer
le branchement, assurez-vous que l'appareil est
compatible avec l'alimentation de gaz que vous
désirez utiliser. Si ce n'est pas le cas, suivez les
directives indiquées au paragraphe « Adapter à
différents types de gaz ».
Après le raccordement à l'arrivéedegaz, vérifier
qu'il n'y ait pas de fuite à l'aide d'eau savonneuse.
Allumez les brûleurs et tournez les boutons de la
position maximale 1* à la position minimale 2*
pour vérifier la stabilité de la flamme.
Le raccordement au réseau de gaz ou
au cylindre de gaz peut être effectué en
utilisant un tuyau en caoutchouc flexible ou
en acier, conformément à la législation nationale
applicable.
AVERTISSEMENTS ÉLECTRIQUES
IMPORTANT : Des informations concernant la
consommation actuelle et de tension figurent sur
la plaque signalétique.
La plaque signalétique se trouve sur le rebord
avant du four (visible lorsque la porte est ouverte).
Il doit être possible de débrancher l’appareil
de l’alimentation électrique en retirant la fiche de
la prise de courant si elle est accessible, ou à l’aide
d’un interrupteur multipolaire en amont de la prise
de courant, conformément aux règles de câblage
et l'appareil doit être mis à la terre conformément
aux normes de sécurité électrique nationales.
Une fois l'appareil installé dans son meuble, le câble d'alimentation
doit être suffisamment long pour le brancher à l'alimentation électrique
principale. Ne tirez pas sur le cordon d'alimentation pour débrancher
l'appareil.
N'utilisez pas de rallonge, de prises multiples
ou d'adaptateurs. Une fois l'installation terminée,
l'utilisateur ne devra plus pouvoir accéder aux
composantes électriques. N'utilisez pas l'appareil
si vous êtes mouillé ou si vous êtes pieds nus.
N'utilisez pas l'appareil si le câble d'alimentation
ou la prise de courant est endommagé(e), si
l'appareil ne fonctionne pas correctement, ou s'il a
été endommagé ou est tombé.
Si le câble d'alimentation est endommagé, il
doit être remplacé avec un câble identique par le
fabricant, un représentant du Service Après-vente,
ou par toute autre personne qualifiée - vous
pourriez vous électrocuter.
Si le câble électrique doit être remplacé,
contactez un centre de maintenance agréé.
MISE EN GARDE : Pour éviter toute décharge
électrique, assurez-vous que l'appareil est éteint
avant de remplacer l'ampoule.
NETTOYAGE ET ENTRETIEN
AVERTISSEMENT : Assurez-vous que l'appareil
est éteint et débranchez de l'alimentation
électrique avant d'effectuer le nettoyage ou
l'entretien ; n'utilisez jamais un appareil de
nettoyage à vapeur - risque de choc électrique.
N'utilisez pas de produits abrasifs ou de
grattoirs métalliques pour nettoyer la vitre de la
porte, ils peuvent rayer la surface et, à la longue,
briser le verre.
N'utilisez en aucun cas de produits abrasifs
ou corrosifs, de produits chlorés ou de tampons à
récurer.
Assurez-vous que l’appareil a refroidi avant de
le nettoyer ou effectuer des travaux d’entretien. -
Risque de brûlures.
MISE EN GARDE : Éteignez l’appareil avant
de remplacer l’ampoule - vous pourriez vous
électrocuter.
Pour éviter d'endommager le dispositif d'allumage électrique, ne
pas l'utiliser lorsque les brûleurs ne sont pas en place.
Portez des gants de protection pour effectuer le
nettoyage et l’entretien.
ÉLIMINATION DES MATÉRIAUX D'EMBALLAGE
Lesmatériauxd'emballagesontentièrementrecyclablescommel'indique
le symbole de recyclage . Les différentes parties de l'emballage
doivent donc être jetées de manière responsable et en totale conformité
avec la réglementation des autorités locales régissant la mise au rebut
de déchets.
MISE AU REBUT DES APPAREILS
ÉLECTROMÉNAGERS
Cet appareil est fabriqué avec des matériaux recyclables ou pouvant
être réutilisés. Mettez-le au rebut en vous conformant à la
réglementation locale en matière d'élimination des déchets. Pour
toute information supplémentaire sur le traitement et le recyclage
des appareils électroménagers, contactez le service local compétent,
le service de collecte des déchets ménagers ou le magasin vous
avez acheté l'appareil. Cet appareil est certifié conforme à la Directive
européenne 2012/19/UE relative aux déchets d'équipements électriques
et électroniques (DEEE). En s'assurant que ce produit est correctement
mis au rebut, vous contribuerez à empêcher toute conséquence nuisible
pour l'environnement et la santé. Le symbole
sur le produit ou
sur la documentation qui l'accompagne indique qu'il ne doit pas être
traité comme un déchet domestique, mais doit être remis à un centre
de collecte spécialisé pour le recyclage des appareils électriques et
électroniques.
CONSEILS RELATIFS À L'ÉCONOMIE D'ÉNERGIE
Préchauffez le four uniquement si cela est spécifié dans le tableau de
cuisson ou dans votre recette. Utilisez des plaques de cuisson foncées,
laquées ou émaillées, car elles absorbent mieux la chaleur.
Utilisez un autocuiseur pour économiser encore plus d'énergie et de
temps.
DÉCLARATION DE CONFORMITÉ
Cet appareil respecte les exigences d’écoconception du règlement
européen 66/2014 conformément à la norme européenne EN 60350-1.
Cet appareil respecte les exigences d’écoconception du règlement
européen 66/2014 conformément à la norme européenne EN 60350-2.
Cet appareil respecte les exigences d’écoconception du règlement
européen 66/2014 conformément à la norme européenne EN 30-2-1
Cet appareil respecte les exigences d’écoconception du règlement
européen 65/2014 conformément à la norme européenne EN 15181.
10
AR
.
،
ء
ء.
:
.
،:
)
(.
ﺿ،،،
)(.
ﺿ،
.
.
ً.
ء.
،
،ﺿ
.
:ء
..
8
.
:،-
.
::ء
.
:.
.
:ُء
،-.
ءء،
ءء.
.
ء-.
ء)0-3(.
ء)3-8(
.
ء8
،
..
.
::-ء
،ﺿ
،
،-
ء.
ءء.
ء
:ء
..
8
.
ءً.
،
-.
ء-.
ﺿ-.
.ء،
،ء
-.
ء-.
ﺿ
ﺿ.
ﺿ،
.
15.
15،
/
.
:
.
:
،،ء
.
ُ)
ُ(.
.
ء.
)
(-
.
)(.
.
ﺿ:
.
ء
:
.
،،.
ء)(.
11
،ُ
.
،
.
.،
.
-
.-
.
ء
.
ءء)
(.
ءء
.
.،
ء.،
.ء،
)(
-.
ء-.ء
،ء-
.
ء.
:
ﺿﺿ
.
ء
.
ء،
ء.
ء2/.
ءء
ﺿ100
،ﺿ.
ء
،
ءﺿ.
.
ء.
.ً
ء،
)،(.ء
ﺿ
ﺿ
)(
50°.
،،
.
.
.
.
،
)(ء.
)(:
ﺿ،
.
:)(
،
.
.
45x560.
-
.
-
.
ﺿ،
،
.
:،
.ء.
:،)
ﺿ(.
ﺿ
1)""(.
:
)(.
:.
ً.
.
،
.
:،
)(.
:
.
)(
ﺿ.L
.
)(.
1/2.
12
1/2.
2000.،
ء
.
.
:،
ء)(.
.
.،
.
،ﺿ"ء
".
،
ء.
ﺿ1*ﺿ2*.
،ً.
:
.
)
(.
ء
،
،
ﺿ،.
ءء
.ء.
،
.ء
.
.
ء،،
ً،.
-.
ء،
.
:
.
:ء
ء،
-.
،،
.
.
.-
.
:-
.
ﺿ،
.
ء.
100%
.،
ء
.
.
.
،
.
2012/19/EU،)WEEE(.
.
،
.
ًًُ.
ء)(،
.
)(.
66/2014
EN 60350-1.
66/2014
EN 60350-2.
66/2014
EN 30-2-1
65/2014
EN 15181.
13
2
3
4
5
8
12
13
14
1
7
6
10
11
6
9
1.Hob burner
2.Hob Grid
3.Control panel
4.Sliding grill rack
5.DRIPPING pan
6.Adjustable foot
7.Containment surface for spills
8.GUIDE RAILS for the sliding racks
9.position 5
10.position 4
11.position 3
12.position 2
13.position 1
14.Glass Cover
TIMER knob
THERMOSTAT knob
Hob BURNER control knob
Hob BURNER control knob
EN
EN
PRODUCT DESCRIPTION
ENEN
Read the safety instructions carefully before using the product
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
DAILY REFERENCE
GUIDE
CONTROL PANEL
Hob BURNER control knob
1
2
1.
2.
3.
3
Hob BURNER control knob
4
5
6
4.
5.
6.
14
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas
other than the default type (this is indicated on the
rating label on the cover).
Adapting the hob
Replacing the nozzles for the
hob burners:
1. Remove the hob grids and
slide the burners off their seats.
2. Unscrew the nozzles using
a 7 mm socket spanner (see
gure), and replace them with
nozzles suited to the new type
of gas(see Burner and nozzle speci cations table).
3. Replace all the components by following the above
instructions in reverse.
Adjusting the hob burners’ minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory screw,
which is positioned inside or next to the tap pin, until
the flame is small but steady.
If the appliance is connected to a liquid gas supply,
the regulatory screw must be fastened as tightly as
possible.
3. While the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa several
times, checking that the flame is not extinguished.
The hob burners do not require primary air
adjustment.
A
V
Adapting the oven
Replacing the oven burner
nozzle:
1. Remove the oven
compartment.
2. Slide out the protection panel
A
(see diagram).
3. Remove the oven burner
after unscrewing the screws V
(see  gure).
The whole operation will be
made easier if the oven door is
removed.
If the appliance is connected to liquid gas, the
adjustment screw must be fastened as tightly as
possible.
5. Turn the knob from the MAX position to the MIN
position quickly or open and shut the oven door,
making sure that the burner is not extinguished.
4. Unscrew the nozzle using a
special nozzle socket spanner
(see  gure) or with a 7 mm
socket spanner, and replace it
with a new nozzle that is suited to the new type of gas
(see Burner and nozzle speci cations table).
Adjusting the gas oven burner’s minimum setting:
1. Light the burner (see Start-up and Use).
2. Turn the knob to the minimum position (MIN)
after it has been in the maximum position (MAX) for
approximately 10 minutes.
3. Remove the knob.
4. Tighten or loosen the adjustment screws on the
outside of the thermostat pin (see  gure) until the flame
is small but steady.
Be careful of the spark plug wires and the
thermocouple tubes.
The oven and grill burners do not require primary air
adjustment.
Installation tips
After adjusting the appliance so it may be used with
a different type of gas, replace the old rating label with
a new one that corresponds to the new type of gas
(these labels are available from Authorised Technical
Assistance Centres).
Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet hose in
accordance with current national regulations relating to
“regulators for channelled gas”.
This procedure must be performed by a qualified
technician who has been authorised by the
manufacturer.
EN
15
S
S
R
A
This procedure must be performed by a qualified
technician who has been authorised by the
manufacturer.
Table of burner and nozzle specifications
Table 1 Liquid Gas Natural Gas
Burner Diameter
(mm)
Thermal Power
kW (p.c.s.*)
By-Pass
1/100
Nozzle
1/100
Flow*
g/h
Nozzle
1/100
Flow*
l/h
Nominal Reduced (mm) (mm) *** ** (mm)
Fast
(Large)(R)
100 3.00 0.7 41 87 218 214 128 286
Semi Fast
(Medium)(S)
75 1.90 0.4 30 69 138 136 104 181
Auxiliary
(Small)(A)
51 1.00 0.4 30 50 73 71 78 95
Oven - 2.80 1.0 46 80 204 200 119 267
Supply
Pressures
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
* At 15°C and 1013 mbar- dry gas
** Propane P.C.S. = 50,37 MJ/Kg
*** Butane P.C.S. = 49,47 MJ/Kg
Natural P.C.S. = 37,78 MJ/m
3
TECHNICAL DATA
Power supply voltage
and frequency
see data plate
Burners
may be adapted for use with any
type of gas shown on the data
plate, which is located inside the
flap or, after the oven
compartment has been opened,
on the left-hand wall inside the
oven.
After installing the power cable, screw the metal cover
with three screws.
EN
16
Using the hob
Lighting the burners
For each BURNER knob there is a complete ring showing
the strength of the flame for the relevant burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an
anticlockwise direction so that it is pointing to the
maximum flame setting
.
3. Adjust the intensity of the flame to the desired level
by turning the BURNER knob in an anticlockwise
direction. This may be the minimum setting
, the
maximum setting or any position in between the two.
If the appliance is fitted with an electronic lighting
device* (C), simply press the BURNER knob and turn it
in an anticlockwise direction
so that it is pointing to the
maximum flame setting, until
the burner is lit. The burner
may be extinguished when
the knob is released. If this
occurs, repeat the operation,
holding the knob down for a
longer period of time.
If the flame is accidentally extinguished, switch off the
burner and wait for at least 1 minute before attempting
to relight it.
If the appliance is equipped with a flame failure safety
device* (X), press and hold the BURNER knob for
approximately 2-3 seconds to keep the flame alight
and to activate the device.
To switch the burner off, turn the knob until it reaches
the stop position •.
Practical advice on using the burners
For the burners to work in the most efficient way
possible and to save on the amount of gas consumed,
it is recommended that only pans that have a lid and
a flat base are used. They should also be suited to the
size of the burner.
To identify the type of burner, please refer to the
diagrams contained in the “Burner and nozzle
specifications”.
Using the oven
The first time you use your appliance, heat the empty
oven with its door closed at its maximum temperature
for at least half an hour. Ensure that the room is well
ventilated before switching the oven off and opening
the oven door. The appliance may emit a slightly
unpleasant odour caused by protective substances
used during the manufacturing process burning away.
! We recommend cleaning the oven before using it for
the first time, following the instructions provided in the
„Care and maintenance” section.
X
C
Burner Cookware diameter (cm)
Fast (R) 24 - 26
Semi Fast (S) 16 - 20
Auxiliary (A) 10 - 14
Flame adjustment according to levels
the burner flame intensity can be adjusted with the
knob according to 6 power levels, from maximum
to minimum with 4 intermediate positions:
a click will indicate the change from one level to
another when turning the knob. The system
guarantees a more precise adjustment, allows
to replicate the flame intensity and to identify
easily the preferred level for different cooking
operations.
*
Only available in certain models.
If, after 15 seconds, the burner is still not alight, release
the knob, open the oven door and wait for at least 1
minute before trying to light it again.
The oven is fitted with a safety device and it is
therefore necessary to hold the OVEN control knob
down for approximately 6 seconds.
If the flame is accidentally extinguished, switch off the
burner and wait for at least 1 minute before attempting
to relight the oven.
Never put objects directly on the bottom of the oven;
this will avoid the enamel coating being damaged.
Only use position 1 in the oven when cooking with the
rotisserie spit.
Lighting the oven
To light the oven burner, bring a flame or gas lighter
close to opening F (see  gure) and press the OVEN
control knob while turning it in
an anticlockwise direction until
it reaches the MAX position.
If the appliance is fitted with an
electronic lighting device* (see
gure), press the OVEN knob
and turn it in an anticlockwise
direction, towards the MAX
position, until the burner is lit.
F
EN
START-UP AND USESTART-UP AND USESTART-UP AND USESTART-UP AND USESTART-UP AND USESTART-UP AND USE
17
Adjusting the temperature
To set the desired cooking temperature, turn the
OVEN control knob in an anticlockwise direction.
Temperatures are displayed on the control panel and
may vary between MIN (140°C) and MAX (250°C).
Once the set temperature has been reached, the oven
will keep it constant by using its thermostat
A
S
Oven light
This is switched on by pressing the OVEN LIGHT
button
Lower compartment
The internal surfaces of the
compartment (where present)
may become hot.
Do not place flammable materials in the lower oven
compartment.
In gas cooker models, there is a sliding protection layer
A that shields the lower compartment from the heat
generated by the burner (see  gure).
To remove the sliding
protection remove the screw S
(see  gure). To replace it, lock it
in place with the screw S.
Before using the oven make
sure that the sliding protection
is fixed correctly.
Timer*
To activate the Timer proceed as follows:
1. Turn the TIMER knob in a clockwise direction for
almost one complete revolution to set the buzzer.
2. Turn the TIMER knob in an anticlockwise direction
to set the desired length of time.
18
Oven cooking advice table
Foods
Weight (in
kg)
Rack
position
Preheating time (min)
Recommended
Temperature (°C)
Cooking time
(minutes)
Pasta
Lasagne
Cannelloni
Gratin dishes
2.5
2.5
2.5
10
10
10
200-210
200
200
75-85
50-60
Meat
Veal
Chicken
Duck
Rabbit
Pork
Lamb
1.5
1.5
1.8
2
2.1
1.8
3
3
3
3
3
3
10
10
10
10
10
10
210-220
200
200
200
200
95-100
90-100
100-110
70-80
70-80
100-105
Fish
Mackerel
Dentex
Trout baked in foil
1.1
1.5
1
3
3
3
10
10
10
180-200
180-200
180-200
45-50
45-55
45-50
Pizza
Neapolitan-style
1
4
15
20-25
Pies
Biscuits
Tart
Savoury pies
Leavened cakes
0.5
1.1
1
1
3
3
3
3
15
15
15
15
180
180
180
170
30-35
30-35
45-50
35-40
Grilled foods
Veal steak
Cutlets
Hamburgers
Mackerel
Toast
1
1.5
1
1
4 pcs
4
4
3
4
4
5
5
5
5
5
15-20
20
20-30
15-20
4-5
Grilling using the rotisserie*
Spit-roast veal
Spit-roast chicken
1
2
-
-
5
5
70-80
70-80
Grilling using the multi-spit rotisserie*
Meat kebabs
Vegetable kebabs
1
0.8
-
-
5
5
40-45
25-30
50-60
4
4
4
200-210
210-220
EN
19
Care and maintenance
Switching the appliance off
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Inspecting the oven seals
Check the door seals around the oven periodically. If
the seals are damaged, please contact your nearest
Authorised After-sales Service Centre. We recommend
that the oven is not used until the seals have been
replaced.
Gas tap maintenance
Over time, the taps may become jammed or difficult to
turn. If this occurs, the tap must be replaced.
This procedure must be performed by a qualified
technician who has been authorised by the
manufacturer.
Replacing the oven light bulb
1. After disconnecting the oven
from the electricity mains, remove
the glass lid covering the lamp
socket (see figure).
2. Remove the light bulb and
replace it with a similar one:
voltage 230 V, wattage 25 W,
cap E 14.
3. Replace the lid and reconnect the oven to the electricity
supply.
Do not use the oven lamp as/for ambient lighting.
Assistance
Please have the following information handy:
The appliance model (Mod.).
The serial number (S/N).
This information can be found on the data plate located
on the appliance and/or on the packaging.
• Cook your food in closed pots or pans with well-fitting
lids and use as little water as possible. Cooking with
the lid off will greatly increase energy consumption
• Use purely flat pots and pans
• If you are cooking something that takes a long time,
it's worth using a pressure cooker, which is twice as
fast and saves a third of the energy.
Respecting and conserving the environment
• Whenever possible, avoid pre-heating the oven
and always try to fill it. Open the oven door as little
as possible because heat is lost every time it is
opened. To save a substantial amount of energy,
simply switch off the oven 5 to 10 minutes before the
end of your planned cooking time and use the heat
the oven continues to generate.
• Keep gaskets clean and tidy to prevent any door
energy losses
• If you have a timed tariff electricity contract, the “delay
cooking” option will make it easier to save money by
moving operation to cheaper time periods.
• The base of your pot or pan should cover the hot plate.
If it is smaller, precious energy will be wasted and
pots that boil over leave encrusted remains that can
be difficult to remove.
AFTER-SALES SERVICE
To receive assistance, call the number given on the
warranty leaflet enclosed with the product or follow
the instructions on our website. Be prepared to
provide:
a brief description of the problem;
the exact model type of your product;
the assistance code (the number following the word
SERVICE on the identification plate attached to the
product, which can be seen on the inside edge when
the oven door is open);
your full address;
a contact telephone number.
Please note: If repairs are required, contact an
authorised service centre that is guaranteed to use
original spare parts and perform repairs correctly.
Please refer to the enclosed warranty leaflet for more
information on the warranty.
WWW
A complete product specification, including the energy efficiency ratings for this oven, can be read and
downloaded from our website
www.indesit.com
The cover
If the cooker is fitted with
a glass cover, this cover
should be cleaned using
lukewarm water. Do not
use abrasive products.
It is possible to remove
the cover in order to make
cleaning the area behind
the hob easier. Open
the cover fully and pull it
upwards (see  gure).
Do not close the cover
when the burners are alight or when they are still hot.
EN
20
1 / 1

Ariston AS5G1PMX/MEA Mode d'emploi

Catégorie
Fours
Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues