GE Appliances CKLBLSFNW2 Guide d'installation

This kit provides for the installation of a unified grille panel

for a framed or overlay custom panel. The panel will span

the combined width of a side by side installation.

Completion Time: Allow approximately 2 hours to install

this kit.

IMPORTANT: 2 People are required to install this kit.

Disconnect power before you begin.

Installation

Instructions

ZKBSN720NSS - Stainless Steel

Unification Kit and

ZKBFN720NII Panel Unification Kit

CONTENTS:

DESIGN GUIDE

STANDARD INSTALLATION - Case Flush to Cabinet

with Proud Doors

The Installation Space ...................... 2

Dimensions and Clearances ................. 2

Grille Panel Dimensions .................... 3

DESIGN GUIDE

FLUSH INSTALLATION - Case Inset to Cabinet with

Flush Doors

The Installation Space ...................... 3

INSTALLATION INSTRUCTIONS

MATERIALS ................................ 4

GROUNDING THE REFRIGERATOR ............ 5

STEP 1. REMOVE PACKAGING ................ 6

STEP 2. INSTALL WATER LINES .............. 6

STEP 3. INSTALL NEW CENTER TRIM ......... 7

STEP 4. REMOVE BOTH GRILLE PANEL

FRAMES ........................... 7

STEP 5. INSTALL SIDE PANELS .............. 7

STEP 6. INSTALL ANTI-TIP BRACKET .......... 8

STEP 7. POSITION REFRIGERATOR AND

INSTALL TOP TRIM .................. 9

STEP 8. LEVEL REFRIGERATOR ............. 10

STEP 9. INSTALL ANTI-TIP BRACKET ......... 11

STEP 10. SECURE REFRIGERATOR

TO CABINETRY ................... 13

STEP 11A. INSTALL UNIFIED PANEL FRAME . . 14

STEP 11B. INSTALL STAINLESS STEEL

GRILLE PANEL .................. 15

STEP 12. INSTALL CENTER TRIM STRIP ...... 15

STEP 13. ADJUST DOOR SWING ............. 15

STEP 14. CHECK AND CORRECT DOOR

ALIGNMENT ...................... 16

STEP 15. INSTALL GRILLE BASE ............ 18

STEP 16. CONNECT WATER SUPPLY ......... 18

STEP 17. CONNECT POWER ................ 19

STEP 18A. INSTALL STAINLESS STEEL

TOEKICK ....................... 19

STEP 18B. INSTALL CUSTOM TOEKICK FOR

STANDARD INSTALLATION ........ 19

STEP 18C. INSTALL CUSTOM TOEKICK FOR

FLUSH INSET INSTALLATION ...... 19

To consult a French or Spanish version of this instruction manual, visit our Monogram.com website.

In Canada, visit Monogram.ca.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for local inspector’s use. Observe all governing codes and ordinances.

• Note to Installer – Be sure to leave these instructions with the Consumer.

• Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately contact your dealer or builder.

Skill Level – Installation of this unit requires basic mechanical, carpentry and plumbing skills. Proper installation

is the responsibility of the installer. Product failure due to improper installation is not covered under the Monogram

Warranty. See the Owner’s Manual for warranty information.

WARNING

Fire or Explosion Hazard. Keep flammable materials and vapors away from

appliance. Failure to do so can result in fire, explosion, or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to

have access to small parts during the installation of this product.

THE INSTALLATION SPACE

The installation space must be 71-1/2” wide.

Water and Electrical Locations

The water and electrical locations for each product must

be located as shown.

The cutout depth must be 24”

The refrigerator will project forward, slightly beyond

adjacent cabinetry, depending on your installation.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed

the 24” installation depth shown. The top case trim

overlaps the bottom of the soffit.

Additional Specifications

ƒ A separate 115 volt, 60Hz, 15 or 20 amp power supply

is recommended for each product. An individual

properly grounded branch circuit or circuit breaker

is recommended. Install properly grounded 3-prong

electrical receptacles recessed into the back wall.

Electrical must be located on rear wall as shown.

NOTE: GFI (ground fault interrupter) is not

recommended.

ƒ Both water lines can enter the opening through the

floor or back wall. Route SmartConnect™ kit or 1/4”

O.D. copper tubing between the cold water line and

the water connection location. The tubing should be

long enough to extend t the front of the refrigerator.

Installation of an easily accessible shut-off valve in the

water line is required.

DIMENSIONS AND CLEARANCES

Product and Clearances

These refrigerators are equipped with a 3-position door

stop. The factory set 115° door swing can be adjusted

to 90° if clearance to adjacent cabinets or walls is

restricted.

Allow 25" minimum clearance for a full 130 door swing.

Allow 15" for pan removal.

5" minimum clearance is required when door swing is

adjusted to 90. If the 90 door stop position is used, pan

access is maintained, but pan removal is restricted.

See illustrations to determine door swing interaction with

adjacent cabinets or countertops.

DESIGN GUIDE - STANDARD INSTALLATION

25”

Min. to

Wall

25”

Min. to

Wall

1”

130° Door

Swing

130° Door

Swing

71-1/2"

Case Width

25-3/4"

Case Depth

28-1/2" Depth

Including Handles

72" Frame to

Frame Width

*Shipping height. The

refrigerators can be adjusted

to fit into a cutout that is

83-1/2" min. to 84-1/2" max.

Note that the top case trim

at the front is 1/2" higher and

will overlap upper cabinetry

or soffit. Use leveling legs

and wheels for a maximum

1" height adjustment.

*84"

83-1/2"

at Rear

23-7/8"

Behind

Frame

36-3/4"

4" Minimum

to Wall

90°

2

31-1000414 Rev. 1

DESIGN GUIDE - STANDARD INSTALLATION

DESIGN GUIDE - FLUSH INSTALLATION

REQUIRED DIMENSIONS FOR GRILLE PANELS

Panels must be cut to the dimensions shown.

IMPORTANT NOTE: The maximum weight for the unified

grill is 25 pounds.

Assemble the overlay panels as shown, using glue and

screws. Center the spacer panel on the backer panel.

Center the overlay panel on the backer and spacer panel.

A

B

Grille Panel

Framed Panel Dimensions

1/4” (0.63 cm)

Framed Panel

A (Width) B (Height)

69-7/8” (177.48 cm) 8-7/8” (22.54 cm)

Overlay Panel Dimensions

1/4” (0.63 cm)

Backer Panel

A (Width) B (Height)

69-7/8” (177.48 cm) 8-7/8” (22.54 cm)

0.10” (0.25 cm)

Spacer Panel

68-1/2” (97.79 cm) 7-5/8” (20 cm)

3/4” (1.9 cm)

Overlay Panel

70-1/8” (178.12 cm) 9” (22.86 cm)

INSTALLATION SPACE

See ZKFN Kit for Installation Space, Unified Door

Panel Dimensions, Unified Grille Panel Dimensions,

Side Cleats, and Toe Kick Dimensions.

3

31-1000414 Rev. 1

INSTALLATION INSTRUCTIONS

Tools Required:

• Tinsnips to cut banding

• Stepladder

• Bucket

• Level

• Appliance dolly

• Tubing cutter

• 7/16" open-end wrench

• #1 and #2 Phillips screwdrivers

• Drill and appropriate bits

• 5/16", 7/16" socket

• Safety glasses

• 1-1/4" open-end wrench

• Pliers

• 1/4" ratchet or 1/4" angled wrench

• Tape measure

• Gloves to protect against sharp edges

Hardware Supplied:

• Water filter bypass plug

•Anti-tip brackets

•1/4" nut and ferrule

Parts List:

A. Top trim

B. Left inside case trim

C. Right inside case trim

D. Center U-shape trim

E. Grille base wrap

F. Grille panel

G. Foam spacer pads (6)

H. Toekick

HH. Toekick skirt

I. Phillips screws (28)

J. Package of 12 plastic spacers

K. 2 Corner trim brackets

L. Black #8-32 x 3/8" screws (12)

M #6-32 x .340 screws (4)

Materials Required:

• 71" long 2x4 for Anti-Tip support

• 1/4" copper water line tubing or 2 SmartConnect™

Refrigerator Tubing kits

• 2 Water shut-off valves

• Screws to secure refrigerator to cabinetry

• Stick-on hook and loop fastener strips for 1/4" side

panels.

Flooring:

For proper installation, this refrigerator must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should be

strong enough to support a fully loaded refrigerator, or

approximately 2,400 lbs.

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under the

refrigerator where you are working.

A

B

C

D

E

F

H

G

I

J

M

L

K

HH

4

31-1000414 Rev. 1

GROUNDING THE REFRIGERATOR

WARNING

Electrical Shock Hazard.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT OR

REMOVE THE THIRD (GROUND)

PRONG FROM THE POWER

CORD.

DO NOT USE AN ADAPTER

PLUG TO CONNECT THE REFRIGERATOR TO A

2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

INSTALLATION INSTRUCTIONS

MISE À LA TERRE DU

RÉFRIGÉRATEUR

AVERTISSEMENT

Risque de choc élec-

trique.

Le non-respect de ces instructions peut entraîner des risques

d’incendies, des chocs électriques ou la mort.

Le cordon d’alimentation de cet appareil est équipé d’une

fiche à trois broches (pour une mise à la terre) qui s’adapte à

la prise de courant standard à 3 broches (pour une mise à la

terre) pour minimiser les risques de chocs électriques par cet

appareil.

Faites vérifier la prise murale et le circuit électrique par un

électricien qualifié pour s’assurer que le système est correc-

tement mis à la terre.

Dans le cas d’une prise biphasée, l’installateur a la respon-

sabilité et l’obligation de la remplacer par une prise triphasée

correctement mise à la terre.

NE COUPEZ PAS OU N’ENLEVEZ PAS, SOUS AUCUN

PRÉTEXTE, LA TROISIÈME BROCHE DE MISE À LA

TERRE DU CORDON D’ALIMENTATION.

N’UTILISEZ PAS D’ADAPTATEUR

POUR BRANCHER LE

RÉFRIGÉRATEUR À UNE PRISE

BIPHASÉE.

N’UTILISEZ PAS DE RALLONGE

AVEC CET APPAREIL.

CONEXIÓN A TIERRA DEL

REFRIGERADOR

ADVERTENCIA

Riesgo de Descarga

Eléctrica

Si no se siguen estas instrucciones, se podrá producir la

muerte, incendios o descargas eléctricas.

El cable de corriente de este electrodoméstico cuenta con un

enchufe de 3 cables (conexión a tierra) que se conecta a un

tomacorriente de pared estándar de 3 cables (conexión a tie-

rra) para minimizar el riesgo de posibles descargas eléctricas

por parte del mismo.

Contrate a un electricista calificado para que controle el

tomacorriente y el circuito eléctrico, a fin de asegurar que el

enchufe esté correctamente conectado a tierra.

En caso de contar con un tomacorriente de pared de 2

cables, es su responsabilidad y obligación reemplazarlo por

un tomacorriente de pared de 3 cables correctamente conec-

tado a tierra.

NUNCA, BAJO NINGUNA CIRCUNSTANCIA, CORTE NI

ELIMINE EL TERCER CABLE (TIERRA) DEL

CABLE DE CORRIENTE.

NO USE UN ENCHUFE ADAPTADOR PARA

CONECTAR EL REFRIGERADOR A UN

TOMACORRIENTE DE 2 PATAS.

NO USE UN PROLONGADOR CON ESTE

ELECTRODOMÉSTICO.

5

31-1000414 Rev. 1

INSTALLATION INSTRUCTIONS

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

The refrigerator is much heavier at the top than at the

bottom—be careful when moving. When using a hand

truck, handle from the side only.

AVERTISSEMENT

Risque de

basculement Le réfrigérateur est beaucoup plus lourd en

haut qu’en bas. Il faut être prudent lors des déplacements. Si

un diable est utilisé, il faut soulever le réfrigérateur sur le côté

seulement.

ADVERTENCIA

Riesgo de Caídas

El refrigerador es mucho más pesado en su parte superior

que en su parte inferior – tenga cuidado al moverlo. Al usar

un carro manual, sosténgalo de costado únicamente.

• Carefully cut banding at the top and

bottom, remove the outer carton.

• Slide out the back corner posts (2).

• Slide the carton off the top of the

cabinet.

NOTE: IT IS NOT NECESSARY

TO LAY THE CABINET DOWN IN

ORDER TO REMOVE THE SKID!

• The unit is secured to the skid with

4 slotted tie-down straps. Remove

the four 5/16” bolts from the base channels in the tie-

downs.

• Remove the four 7/16” bolts securing the straps to the

skid.

NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

• The support blocks on the bottom of the refrigeration

case must be removed before the refrigerator is taken

off the skid or damage will occur. Carefully tilt the

refrigerator and slide the blocks out from beneath.

• Remove the tape from the leveling legs.

• Lift the refrigerator off the skid with an appliance dolly.

Handle from the sides.

STEP 2 INSTALL WATER LINES

• Route 1/4” OD copper or SmartConnect

™

plastic

tubing between house cold water line and the water

connection location.

• Tubing should be long enough to extend to the front of

the refrigerator. Allow enough tubing to accommodate

bend leading into the water line connection.

NOTE: The only Monogram-approved plastic tubing is

supplied in the SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Other

types of plastic may crack or rupture with age and

cause water damage to your home.

SmartConnect

™

Refrigerator Tubing Kits are available

in the following lengths:

2’ (.6 m) - WX08X10002 15’ (4.6 m) - WX08X10015

8’ (2.4 m) - WX08X10006 25’ (7.6 m) - WX08X10025

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the

line of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

• Turn on the main water supply and flush debris.

Run about a quart of water through the tubing into a

bucket. Shut off water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in

many water supply kits, but are not recommended for

this application.

If the water supply to the refrigerator is from

a Reverse Osmosis Water System, use the

refrigerator’s filter bypass plug. Using the

refrigerator’s water filtration cartridge with the RO

filter can result in hollow ice cubes.

STEP 2 INSTALL WATER LINES

WARNING

Connect to potable water supply

only.

AVERTISSEMENT

Raccordez l’appareil à une ali-

mentation d’eau potable seulement.

ADVERTENCIA

Realice la conexión a un sumi-

nistro de agua potable únicamente.

• A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 p.s.i. (275-827 kPa).

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle

valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed plumber.

Floor

Waterline

Tubing

Filter Bypass Plug

6

31-1000414 Rev. 1

STEP 3 INSTALL NEW CENTER

TRIM

NOTICE: Handle parts with care to avoid scratching.

A. Remove the factory installed inside case trims and

top case trims.

B. Install inside case trims (B & C) with notches toward

the bottom. Install screws (I) through 5 slots on each

trim.

C. Apply the supplied foam spacer pads (G) to the

mating side of one product as shown.

NOTE: Flush inset installations require Kit ZKFN. The

ZKFN Kit includes hinge side case trims that should be

installed at this step. The hardware required to install

these trims is included in the ZKFN Kit.

STEP 4 REMOVE BOTH GRILLE

PANEL FRAMES

• Remove 2 or 3 screws holding the grille panel to the

hinge on each side. Lift grille panel off the hinges.

Discard both grille panels. Retain screws or use (L)

screws supplied.

Leave hinges in the open position.

Do not push hinges back.

STEP 5 INSTALL SIDE PANELS

Side panels must be used whenever the sides of the

refrigerator will be exposed. The 1/4” (0.63 cm) side

panels will slip into the side case trim. Secure the

panels to the refrigerator with stick-on hook and loop

fastener strips. Order the side panels from the cabinet

manufacturer.

• Cut a notch in the top front corner as shown to allow

clearance for corner keys in the front side trim.

INSTALLATION INSTRUCTIONS

Foam

Spacer

Pads

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

* Depending on

installation height.

Grille Panel

Remove

2 Screws

Stiffeners

Remove 3

Screws

Grille Panel

7

31-1000414 Rev. 1

STEP 6 INSTALL ANTI-TIP BRACKET

WARNING

Tip Over Hazard.

These refrigerators are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

Read and follow the entire installation instructions for

securing the refrigerator with the anti-tip system.

AVERTISSEMENT

Risque de

basculement Ces réfrigérateurs présentent une

partie supérieure lourde, en particulier avec une porte

ouverte; ils doivent donc être fixés pour prévenir le

basculement vers l’avant et le risque concomitant

de blessure grave ou fatale. Lisez et suivez les

instructions d’installation complètes pour l’installation

du système anti-basculement.

ADVERTENCIA

Riesgo de Caídas

Estos refrigeradores son inestables, especialmente cuando

una puerta se encuentre abierta, y deberán estar asegurados

a fin de evitar caídas hacia adelante que podrían resultar en

la muerte o en lesiones graves. Lea y siga las instrucciones

de instalación en su totalidad para asegurar el refrigerador

con el sistema anti volcaduras.

ƒ&XWDƎ[Ǝ[ƎEORFNDQGVHFXUHWKHEORFNWRWKH

mounting brackets provided using #12 or #14 wood

screws.

ƒ Secure the bracket with wood block to the back wall so

WKDWLWLVƎRU\RXULQVWDOODWLRQKHLJKWIURPWKHILQLVKHG

floor. Use #12 or #14 wood screws. See illustration.

ƒ Screws must penetrate at least one inch into vertical

wall studs.

ƒ Before pushing the refrigerator into the opening, plug

the power cord into the receptacle. Open the grille panel

and reach into the opening at the back to grasp the

power cord. Pull the power cord into the opening as you

push the refrigerator back.

ƒ Gently push refrigerator into the opening with hands

against front corners.

IMPORTANT: When the refrigerator is installed under

a soffit or if there is not enough height for this method

of security, brackets cannot be used. Proceed to step

8 to level the refrigerator and then to step 10 to secure

refrigerator to cabinets. The refrigerator must be secured

to prevent tipping.

INSTALLATION INSTRUCTIONS

2x4 Cut

71" Length

Installation Height

From Floor

Screws Mounted into

Vertical Wall Studs

Mounting

Bracket

Brackets

Required

Height

From

Floor to

Bottom

of

Wood

Block

Side View

Block

6RႈW

Brackets

Not

Required

Beneath a

6RႈW

8

31-1000414 Rev. 1

STEP 7 POSITION REFRIGERATOR AND INSTALL TOP TRIM

• Before pushing the refrigerators into the

opening, plug the power cords into the

receptacles. Reach into the top opening

to grasp the power cord. Pull the power

cord into the opening as you push the

refrigerator back.

• With hands against front corners,

push one refrigerator part-way into the

opening. The refrigerator should be

DSSUR[LPDWHO\ƎIRUZDUGRIWKHEDFN

wall.

• Gently push the second refrigerator next

to the other. The doors should be flush to each other

and the inside trims together.

• Install corner bracket (K) into each side of the top trim

(A). Use 4 screws (M) if needed.

• Place the top trim across the top of the refrigerators

and slip the corner brackets into the outside case

trims.

• Install 8 screws (I) through the top of the trim and into

the top case.

• Check to be sure the inside trims are aligned top and

bottom. There should be a slight gap between the

case trims.

• Remove the Grill Base wraps. 6 screws will be

removed from each grille base wrap. Keep the screws

for future steps.

PUSH REFRIGERATOR INTO OPENING

NOTE: 2 PEOPLE ARE REQUIRED TO PUSH THE

UNIFIED REFRIGERATORS INTO THE OPENING.

• With hands against the front corners, gently push the

unified refrigerators into the opening or against the

back wall.

Soffit

$SSUR[Ǝ

Corner Trim

Bracket

INSTALLATION INSTRUCTIONS

9

31-1000414 Rev. 1

STEP 8 LEVEL REFRIGERATOR

Place a level inside the top of each unit.

Both refrigerators MUST BE LEVEL AND PLUMB with

each other and with adjacent cabinetry on each side.

Drawers should be evenly aligned.

Both refrigerators have 4-point leveling. The front is

supported by leveling legs, the rear is supported by

adjustable wheels. Both are accessible from the front of

the refrigerator.

7ROHYHOWKHEDFNRIWKHUHIULJHUDWRUWXUQWKHƎKH[

nut located above the front wheels. Turn clockwise to

raise or counterclockwise to lower the refrigerator.

)RUIURQWOHYHOLQJXVHDƎRSHQHQGZUHQFK

• Adjust height of refrigerator to match installation cutout

RSHQLQJWRƎ7KHUHIULJHUDWRUVKRXOGEH

level and plumb with cabinetry.

The rear leveling wheels and front leveling legs are lim-

ited to a maximum height adjustment of 1” (2.54 cm). If

the installation requires more than 84-1/2” (214.63 cm)

height, the installer should elevate the refrigerator on a

sheet of plywood or runners. Cabinetry trim could also

be added across the top of the opening to shorten the

opening. If you attempt to raise the refrigerator more

than 1” (2.54 cm), you will damage the front leveling

legs and the rear leveling wheels.

INSTALLATION INSTRUCTIONS

Hex Nut Adjusts

Rear Wheels

Leveling Leg

10

31-1000414 Rev. 1

STEP 9 INSTALL ANTI-TIP BRACKET

WARNING

Tip Over Hazard.

The unit is top-heavy and must be secured to prevent

the possibility of tipping forward.

AVERTISSEMENT

Risque de

basculement

L’appareil ménager est beaucoup plus lourd

en haut et il faut le maintenir en place pour éviter la possibilité

de son basculement vers l’avant.

ADVERTENCIA

Riesgo de Caídas

La unidad es pesada en su parte superior y se deberá asegu-

rar a fin de evitar posibles caídas hacia adelante.

• The kit supplied with the unit contains 2 lag bolts and 4

toggles with bolts. The wall bracket will be attached to

the wall in 4 places.

• Measure the opening where the unit is to be installed.

Mark the center with a vertical line.

• Measure up 81-1/2” (207.01 cm) from the floor. Mark

this point on the wall.

• Using a level, draw a horizontal line on the wall at this

height.

• Locate at least 2 studs on the back wall. Mark these

points on the horizontal line.

• Place the bottom of the wall bracket with tabs on the

horizontal line. Align the center notch on the bracket

with the center line on the wall.

• The anti-tip wall bracket has a series of holes. Select 2

holes that match with the located studs. Make sure the

holes selected are on the center of the studs. Mark the

wall at these points.

• Mark an additional hole at each end of the bracket. If

one of the studs is closer to the end of the bracket, mark

an additional hole towards the center of the bracket.

• Drill 1/2” (1.27 cm) holes into the wall board at the loca-

tions marked for the toggles to be mounted (not the stud

markings).

• Drill 3/16” (0.47 cm) holes into wooden studs where

marked. If steel stud construction, drill 1/2” (1.27 cm)

holes into the studs where marked. You will use 2 tog-

gles with the metal studs.

Two Additional

Hole Locations at

Ends of Brackets

Center

Wall Bracket

Line On Wall

Wall Studs

Line on Wall

Center

INSTALLATION INSTRUCTIONS

11

31-1000414 Rev. 1

INSTALLATION INSTRUCTIONS

Anti-Tip Wall Bracket

Bolt

Wall Toggle

Drywall or

Steel Stud

STEP 9 INSTALL ANTI-TIP BRACKET (Cont.)

Install Wall Toggles:

The wall toggles and bolts can be ordered as Service Kit

#WR49X10193. Wall toggles are installed in the drywall

and metal studs for stability. Install the wall toggles as

follows:

• Drill 1/2”

(1.27 cm)

holes at the wall markings made in

the holes at the ends of the wall bracket.

• Hold the metal channel flat against the plastic straps

and slide the channel through the hole.

• Gently pull back at the ends of the plastic straps to

make the channel rest flush behind the wall.

• Hold the ends of the straps in one hand and slide the

plastic cap along the straps until the flange of the cap

is flush with the wall.

• Place your thumb between the plastic straps and bend

up and down to snap the straps off at the wall.

Install Screws and Bolts:

• Have someone hold the wall bracket centered in place

with each of the holes aligned with the correct opening

in the bracket and level with the horizontal line.

• Insert the lag screws through the bracket and into the

stud. Tighten with a wrench.

• Insert the bolts into the toggle by hand until snug.

Tighten with a wrench.

Plastic Straps

Metal Channel

Cap

Wood Stud

Lag Screw

Anti-Tip Wall Bracket

12

31-1000414 Rev. 1

STEP 9 INSTALL ANTI-TIP BRACKET (Cont.)

Remove Grilles for Access to Anti-Tip Locking Hooks

Fresh Food Unit

• Open the access door.

• Remove the 4 screws from the grille on the right and 3

screws from the grille on the left.

• Pull the bottom of the grilles forward, down and out to

remove.

Freezer Unit

• Open the access door.

• Remove the 4 screws from the grille on the right and 3

screws from the grille on the left.

• Pull the bottom of the grille forward, down and out to

remove.

Power Cord

Locate the power cord inside the left cavity. If it has not

been adjusted so the plug is easily accessible, do so

now.

Move Unit into Final Position

• Move appliance toward its final installed location. Align

the tabs on the wall bracket with the openings in the

back of the unit.

• The unit has “L” bolts in the upper left and right cor-

ners inside of the access compartment. These bolts

will interlock with the wall bracket and secure the unit

using the washers and hair pin cotters in the hardware

kit once the unit has been leveled and is in the final

position.

STEP 10 SECURE REFRIGERATOR TO CABINETRY

Whenever possible, perform this step for anti-tip securi-

ty, or when anti-tip brackets cannot be used.

The refrigerator must be secured to prevent tipping.

• Raise the grille panel to access case trim.

• Drill hole in trim and drive screw (I) through the trim

into adjacent cabinet.

• Follow the same procedure on the opposite side.

INSTALLATION INSTRUCTIONS

Screws Screws

13

31-1000414 Rev. 1

INSTALLATION INSTRUCTIONS

STEP 11A INSTALL CUSTOM PANEL UNIFIED GRILLE FRAME

• Remove 4 screws holding center hinge stiffeners to the

small brackets on the unified frame. Retain screws; use

tape to hold small brackets in place.

• Place the unified grille panel frame over the hinges on

the left and right ends, matching screw hole locations.

Install supplied black screws (L) through hinge and into

stiffener on both ends.

• Loosen screws on each side of the trim behind the

frame. Remove bottom trim.

INSERT CUSTOM PANELS

• Slide framed or overlay panel over the metal backer

panel and into the trim. If necessary, tap with a wood

block until panel slips under the top trim piece.

• Reassemble bottom trim. Tighten screws.

SECURE PANEL TO CENTER HINGES

• Reinstall middle stiffeners and slide them to meet the

center hinges.

• Install supplied black screws (L) through center hinges

and into stiffeners.

• Tighten original screws through the stiffeners and into

the small brackets at the bottom trim.

• Grasp grille panel at the center and pull down to close.

NOTE: Check alignment of grille panel to top of doors.

To adjust, loosen bracket to hinge screws on all 4 hinges.

Adjust and tighten screws.

Grille Panel

Remove

Screws

Stiffeners

Tape

Brackets

in Place

Loosen

Side

Trim

Screw

Loosen

Side

Trim

Screw

Slide Panel Into Frame

Backer Panel

Metal Panel

Overlay Panel

Spacer

3/4" Overlay Panel

Custom Panel

Metal Panel

Framed Panel

Grille Panel

Install

Screws

Through

Stiffeners

and Into

Brackets

Stiffeners

Brackets

Install Screws

Through Hinge

and Into Stiffener

14

31-1000414 Rev. 1

STEP 11B INSTALL STAINLESS STEEL UNIFIED GRILLE FRAME

Two people are required to install the Grille Panel.

• Align the extruded holes on the unified stainless steel

grille panel with the leftmost hinge. Drive 3 screws

through the hinge and into the panel. Drive 3 screws

through the rightmost hinge and into the panel. Repeat

for the center hinges.

• Grasp grille panel at the center and pull down to close.

The panel should align evenly with the side of the door.

NOTE: To adjust the grille panel backward or forward,

loosen the 2 attachment screws on all 4 hinges. Slide the

grille panel outward or to the back. Tighten the screws.

Attachment

Screws

Grille Panel

INSTALLATION INSTRUCTIONS

STEP 12 INSTALL CENTER TRIM STRIP

• Open doors fully.

• The case trims should be evenly aligned top

to bottom with a slight gap between them.

• Starting at the top, press center u-shaped

trim strip (D) over the inside case trims of

both refrigerators.

• Continue pressing trim until you reach the

bottom of the case trims. The trim should

align with the top and bottom of case trims.

Case Trim

U-Shape

Trim

15

31-1000414 Rev. 1

INSTALLATION INSTRUCTIONS

STEP 13 ADJUST DOOR SWING

NOTE: This refrigerator has a 3-position door stop.

When space does not allow the door to swing open

fully to 130°, you may change the door swing to a

90° opening. A 130° door swing option is available

for standard installation only. Skip this step if door

opening is satisfactory for your installation

situation.

• Lift the grille panel to access the wire cover trim.

• Remove screws on both sides of the wire cover trim

and rotate off.

• Use pliers to unscrew door stop and reinstall into the

90° or 130° (standard only) position.

• Reinstall the wire cover trim.

WARNING

d

Door Trim Pinch Point Hazard:

Improper installation can lead to a finger pinch point

hazard between the side door trim and the cabinets

when operating the door, especially with children.

To minimize this risk you must follow the installation

instructions for cabinet dimensions, trim assembly, and

door stop angle.

STEP 14 CHECK AND CORRECT

DOOR ALIGNMENT

• Close the grille panel and both doors.

• Check that the freezer drawers and bottom of doors

are horizontal and even at the lower inside corners.

• Carefully measure the inside corners to determine

if an adjustment is needed. A difference of 1/32" is

acceptable and does not reqire adjustment.

SKIP THIS STEP IF DOORS ARE LEVEL.

IMPORTANT: If the doors are not evenly aligned,

they must be removed and spacers must be installed

to raise or lower both doors.

Pin Location

For 90°

Door Swing

Pin Location

as Shipped

For 115°

Door Swing

Spacer

Location

Spacer

Location

Remove grille screws

STEP 13 ADJUST DOOR SWING

(Cont.)

AVERTISSEMENT

d

Risque de pincement de

doigts : Une installation incorrecte peut poser un risque de

coincement de doigts entre la garniture de porte latérale

et les armoires en actionnant la porte, en particulier pour

les enfants. Pour réduire ce risque, vous devez suivre les

instructions d’installation relatives aux dimensions d’armoire,

au montage des garnitures et à l’angle de l’arrêt de porte.

ADVERTENCIA

d

Riesgo de Lastimadura

con el Marco de la Puerta : Una instalación inadecuada

podrá conducir a riesgos de pellizcos de dedos entre el

marco lateral de la puerta y los gabinetes al utilizar la puerta,

especialmente con los niños. A fin de minimizar este riesgo,

usted deberá seguir las instrucciones de instalación para

dimensiones de gabinetes, ensambles de marcos y ángulos

de detención de puertas.

16

31-1000414 Rev. 1

STEP 14 CHECK AND CORRECT DOOR ALIGNMENT (Cont.)

NOTICE: Follow instructions very carefully.

DETERMINE CORRECT SPACER

This kit contains 12 plastic spacers (J) (2 of each size).

Match spacer to illustration below to be sure you have

selected the correct size as determined in the charts below.

LH Fresh Food door is higher than the RH door:

Select the correct spacers to install on the Fresh Food

hinges as determined by Dimension A.

LH Door Dim. A

Install LH

Spacer

Install RH

Spacer

ƎWRƎ Ǝ Ǝ

1/16ƎWRƎ Ǝ Ǝ

ƎWRƎ Ǝ Ǝ

ƎWRƎ 1/8Ǝ Ǝ

ƎWRƎ Ǝ Ǝ

ƎWRƎ Ǝ Ǝ

RH Fresh Food door is higher than the LH door:

Select the correct spacers to install on the Fresh Food

hinges as determined by Dimension A.

RH Door Dim. A

Install LH

Spacer

Install RH

Spacer

ƎWRƎ Ǝ Ǝ

ƎWRƎ Ǝ Ǝ

3/32ƎWRƎ Ǝ Ǝ

ƎWRƎ Ǝ Ǝ

ƎWRƎ 9/32Ǝ Ǝ

ƎWRƎ Ǝ Ǝ

NOTE: If this plastic spacer package is misplaced, order

WR49X10162 for a replacement kit.

1. Open the grille panel.

2. Remove 4 screws on the hinge plate.

3. Use pliers to remove door stop pin.

4. Lift door off bottom hinge pin. The door must be held

in place while spacers are being exchanged.

5. Remove the original plastic spacer.

6. Place the selected spacer over the hinge.

7. Reverse all steps to replace the door

Ǝ

Ǝ

Ǝ

Ǝ

Ǝ

Ǝ

Dimension

A

Dimension

A

Remove

Remove 4 Screws

Lift off and replace

plastic spacer

INSTALLATION INSTRUCTIONS

17

31-1000414 Rev. 1

STEP 15 INSTALL GRILLE BASE WRAP

• Open doors fully. Open the grille panel.

• Install the unified double width grille base wrap (E) by

slipping the notched ends over the door hinges and

behind metal grates.

• Replace all 12 screws to install unified double width

grille base wrap and metal grates. Refer to Step 7.

STEP 16 CONNECT WATER SUPPLY

Connect both refrigerators to the water supply.

• Locate and bring tubing to the front of the cabinet.

• Turn the water on to flush debris from line. Run about

a quart of water through tubing into a bucket, then shut

off water.

Copper Tubing:

6OLSDƎQXWDQGIHUUXOHSURYLGHGRYHUERWKHQGVRI

the copper tubing. Insert tube into the union fitting on

the unit and tighten nut to union.

• Turn on the water to check for leaks.

SmartConnect™ Tubing:

• Insert the molded end of the tubing into the refrigerator

connection. Tighten the compression nut until it is just

hand tight.

• Tighten one additional turn with a wrench.

Overtightening can cause leaks!

• Turn on the water to check for leaks.

NOTE: Make sure excess tubing length does not

interfere with drawer closing or toekick installation.

Unified Grille Base Wrap

Place Trim

Over Hinges

House

Water Supply

Refrigerator

Water Supply

INSTALLATION INSTRUCTIONS

18

31-1000414 Rev. 1

INSTALLATION INSTRUCTIONS

STEP 17 CONNECT POWER

• Check to be sure the power cord is plugged into the

receptacle.

• Check to make sure power to refrigerator is on by

opening refrigerator door to see if interior lights are on.

• The temperature controls are preset at 37°F for the

fresh food section and 0°F for the freezer.

• Allow 24 hours for temperature to stabilize before

making adjustments.

STEP 18A INSTALL STAINLESS

STEEL TOEKICK

• Attach the toekick assembly to the refrigerator using

the 4 supplied screws (I) - one on each side and two

in the center.

STEP 18B INSTALL CUSTOM

TOEKICK FOR STANDARD

INSTALLATION

• A custom toekick can be installed to match or

complement the surrounding cabinetry. Use the

supplied toekick as a template to cut the shape.

IMPORTANT: A custom toekick can be installed to

match or complement the surrounding cabinetry but

can NOT cover the horizontal vent slots of the factory

toekick.

STEP 18C INSTALL CUSTOM

TOEKICK FOR FLUSH INSET

INSTALLATION

• A custom toekick can be installed to match or

complement the surrounding cabinetry. See

Installation Instructions for ZKFN Kit.

Electrical

Outlet

Master Light

Switch

Raise

Grille

Panel

H

HH

19

31-1000414 Rev. 1

NOTE: While performing installations described in this book,

safety glasses or goggles should be worn.

NOTE: Product improvement is a continuing endeavor at

Monogram. Therefore, materials, appearance and specifications

are subject to change without notice.

Monogram.com

31-1000414 Rev. 1

02-20 GEA

La page charge ...

GE Appliances CKLBLSFNW2 Guide d'installation

Ce manuel convient également à

GE Appliances CKLBLSFNW2 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents