Toro Power Max e26 60V Snowthrower Manuel utilisateur

Form No. 3460-976 Rev A

Power Max® e26 60V Snowthrower

39926/T

Lanzanieves Power Max® e26 60 V

39926/T

Soufeuse à neige Power Max® e26 de 60 V

39926/T

www .T oro.com.

*3460-976*

Form No. 3460-973 Rev A

Power Max

®

e26 60V Snowthrower

Model No. 39926 —Serial No. 414300000 and Up

Model No. 39926T —Serial No. 41 1700000 and Up

Operator's Manual

Introduction

This machine is intended to be used by residential

homeowners. It is designed primarily for removing

snow from paved surfaces, such as driveways and

sidewalks, and other surfaces for traf c on residential

or commercial properties. It is not designed for

removing materials other than snow . It is designed to

use T oro 60V lithium-ion battery packs. These battery

packs are designed to be charged only by T oro 60V

lithium-ion battery chargers. Using this product for

purposes other than its intended use could prove

dangerous to you and bystanders.

Model 39926T does not include a battery or a

charger .

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for product safety and operation

training materials, accessory information, help nding

a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g397375

Figure 1

1. Model and serial number location

Model No.

Serial No.

81 1 1 L yndale A venue South

Bloomington, MN 55420 Register at www .T oro.com.

Original Instructions (EN)

Printed in Mexico

*3460-973*

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

W ARNING

CALIFORNIA

Proposition 65 W arning

The power cord on this product contains

lead, a chemical known to the State

of California to cause birth defects

or other reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety ....................................................................... 3

........................................................................... 3

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup ........................................................................ 9

1 Mounting the Battery Charger

(Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 Installing the Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Installing the Upper Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Installing the T raction-Control Linkage . . . . . . . . . . . . 1 1

5 Installing the Chute-Control Rod . . . . . . . . . . . . . . . . . . . . . 1 1

6 Installing the Snow-Cleanout T ool . . . . . . . . . . . . . . . . . . 12

7 Checking the T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

8 Checking the Skids and Scraper . . . . . . . . . . . . . . . . . . . . 13

9 Adjusting the Auger/Impeller Cable . . . . . . . . . . . . . . . . 13

10 Checking the Operation of the T raction

Drive ............................................................. 13

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Installing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

T urning On the Headlight and

Handwarmers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Operating the Handwarmers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Starting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Activating ECO Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating the T raction Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Operating the Speed Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Operating the Auger/Impeller Drive . . . . . . . . . . . . . . . . . . . 19

Operating the Quick Stick® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Clearing a Clogged Discharge Chute . . . . . . . . . . . . . . . . 21

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Shutting Of f the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Removing the Battery Pack from the

Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Preventing Freeze-up after Use . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Recommended Maintenance Schedule(s) . . . . . . . . . . . 23

Preparing for Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Checking and Adjusting the Skids and

Scraper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Checking and Adjusting the T raction

Cable ............................................................ 24

Checking and Adjusting the Auger/Impeller

Cable ............................................................ 25

Checking the Auger-Gearbox-Oil Level . . . . . . . . . . . . . 26

Lubricating the Hex Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Replacing the Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

2

Storing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Safety

IMPORT ANT SAFETY

INSTRUCTIONS

W ARNING

When using an electric machine, always

read and follow basic safety warnings and

instructions to reduce the risk of re, electric

shock, or injury , including the following:

Read All Instructions

I. T raining

1. The operator of the machine is responsible for

any accidents or hazards occurring to others or

their property .

2. Read and understand the contents of this

Operator ’ s Manual before you start the machine.

Ensure that everyone using this machine knows

how to use it, knows how to shut it of f quickly ,

and understands the warnings.

3. Do not allow children to use or play with the

machine, battery pack, or the battery charger;

local regulations may restrict the age of the

operator .

4. Do not allow children or untrained people to

operate or service this device. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate

or service the device.

5. Before using the machine, battery pack, and

battery charger , read all the instructions and

cautionary markings on these products.

6. Become familiar with the controls and proper

use of the machine, battery pack, and battery

charger .

II. Preparation

1. Keep bystanders and children out of the

operating area.

2. Never allow children to operate the machine.

3. Do not operate the machine without all guards

and other safety devices in place and functioning

properly on the machine.

4. Inspect the area where you will use the machine

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

5. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

6. Plugging the battery charger into an outlet that

is not 120 V can cause a re or electric shock.

Do not plug the battery charger into an outlet

other than 120 V .

7. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

8. If the supply cord to the battery charger is

damaged, contact an Authorized Service Dealer

to replace it.

9. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

1 type of battery pack may create a risk of re

when used with another battery pack.

10. Charge the battery pack in a well-ventilated area

only .

1 1. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

12. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant rubber boots; and hearing

protection. T ie back long hair and do not wear

loose clothing or loose jewelry that can get

caught in moving parts.

3

III. Operation

1. Contact with the moving rotor will cause serious

injury . Keep your hands and feet away from all

moving parts of the machine. Keep clear of any

discharge opening.

2. Stay behind the handles and away from the

discharge opening while operating the machine.

3. Using this machine for purposes other than its

intended use could prove dangerous to you and

bystanders.

4. Prevent unintentional starting—Ensure that the

electric-start key is removed from the key switch

before connecting the battery pack and handling

the machine.

5. Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

6. Disengage all clutches and shift into neutral

before starting the machine.

7. Shut of f the machine, remove the electric-start

key , remove the battery pack from the machine,

and wait for all movement to stop before

adjusting, servicing, cleaning, or storing the

machine.

8. Remove the battery pack and electric-start

key from the machine whenever you leave it

unattended or before changing accessories.

9. Do not force the machine—Allow the machine to

do the job better and safer at the rate for which it

was designed.

10. Stay alert—W atch what you are doing and use

common sense when operating the machine.

Do not use the machine while ill, tired, or under

the inuence of alcohol or drugs.

1 1. Operate the machine only in good visibility and

appropriate weather conditions.

12. Use extreme caution when reversing or pulling

the machine toward you.

13. Keep proper footing and balance at all times,

especially on slopes. Use extreme caution when

changing directions on slopes. Do not operate

the machine on exceedingly steep slopes. W alk,

never run with the machine.

14. When not actively clearing snow , disengage

power to the auger .

15. Adjust the collector housing height to clear a

gravel or crushed-rock surface.

16. Do not direct the discharge material toward

anyone. A void discharging material against a

wall or obstruction; material may ricochet toward

you. Shut of f the machine when crossing gravel

surfaces.

17. Exercise extreme caution when operating the

machine on walks or roads. Stay alert for hidden

hazards or traf c.

18. If the machine strikes an object or starts to

vibrate, immediately shut of f the machine,

remove the key , remove the battery pack, and

wait for all movement to stop before examining

the machine for damage. Make all necessary

repairs before resuming operation.

19. Shut of f the machine whenever you leave the

operating position for any reason.

20. Shut of f the machine, remove the electric-start

key , and remove the battery pack(s) before

unclogging the machine and always use a stick

or a cleanout tool to remove the clog.

21. Shut of f the machine, remove the electric-start

key , and remove the battery pack(s) before

loading the machine for hauling.

22. Never operate the machine at high transport

speeds on slippery surfaces.

23. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

24. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

25. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

T oro battery pack only; using another type of

battery pack may cause a re or risk of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

4

IV . Maintenance and Storage

1. Shut of f the machine, wait for all moving parts to

stop, remove the electric-start key , and remove

the battery pack(s) from the machine before

adjusting, servicing, cleaning, or storing the

machine.

2. Do not attempt to repair the machine except as

indicated in the instructions. Have an Authorized

Service Dealer perform service on the machine

using identical replacement parts.

3. W ear gloves and eye protection when servicing

the machine.

4. When servicing the rotor , be aware that the rotor

can still move even though the power source

is of f.

5. For best performance, use only genuine T oro

replacement parts and accessories. Other

replacement parts and accessories could be

dangerous, and such use could void the product

warranty .

6. Maintain the machine—Keep handles dry , clean,

and free from oil and grease. Keep guards

in place and in working order . Use identical

replacement parts only .

7. Check all fasteners at frequent intervals for

proper tightness to ensure that the machine is in

safe working condition.

8. Check the machine for damaged parts. Check

for misaligned and binding moving parts, broken

parts, mounting, and any other condition that

may af fect its operation. Unless indicated in the

instructions, have an Authorized Service Dealer

repair or replace a damaged guard or part.

9. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

10. When you are not using the machine, store it

indoors in a dry , secure place out of the reach

of children.

1 1. When storing the machine for more than 30

days, refer to Storage ( page 28 ) for important

information.

SA VE THESE

INSTRUCTIONS

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal94-8072

94-8072

decal121-6817

121-6817

1. Cutting/dismemberment hazard of hand or foot, impeller

and auger—keep bystanders away .

decal121-6823

121-6823

1. Fast

3. Slow

2. Forward speeds 4. Reverse speeds

decal137-6198

137-6198

1. Cutting/dismemberment

hazard of the ngers or

hand, impeller—do not

place your hand in the

chute.

2. W arning—shut of f the

motor before using the tool

to clear the chute.

6

decal137-6249

137-6249

1. Squeeze the lever to engage the traction drive. 4. Cutting/dismemberment of ngers or hand, impeller

blade—keep away from moving parts; keep all guards and

shields in place; remove the key from the ignition before

servicing the machine.

2. W arning—read the Operator ’ s Manual .

5. Thrown object hazard—keep bystanders away .

3. Cutting/dismemberment of ngers or hand, impeller blade—do

not place your hand in the chute; shut of f the motor before

using the tool to clear the chute.

6. Squeeze the lever to engage the impeller .

decal137-9462

137-9462

decal137-9463

137-9463

1. The battery pack is charging.

2. The battery pack is fully charged.

3. The battery pack is over or under the appropriate temperature range.

4. Battery pack charging fault

7

decal137-9456

137-9456

1. Read the Operator ’ s

Manual .

3. Do not expose to rain.

2. Keep away from open re

or ames.

decal137-9461

137-9461

1. Battery charge status

decal145-3133

145-3133

decal140-2180

140-2180

1. Of f 3. Start

2. Power

8

Setup

Important: The battery pack is not fully charged when you purchase it. Before using the machine for

the rst time, refer to Specications ( page 15 ) .

1

Mounting the Battery Charger (Optional)

Parts needed for this procedure:

2

Mounting hardware (not included)

Procedure

If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of the

charger .

Mount it indoors (such as a garage or other dry place), near a power outlet, and out of the reach of children.

Refer to Figure 3 for assistance in mounting the charger .

Slide the charger over the appropriately positioned hardware to secure the charger in place (hardware not

included).

g290534

Figure 3

9

2

Installing the Chute

No Parts Required

Procedure

g427228

10

3

Installing the Upper Handle

No Parts Required

Procedure

g344102

4

Installing the T raction-Control Linkage

No Parts Required

Procedure

g344097

1 1

5

Installing the Chute-Control Rod

No Parts Required

Procedure

g344094

6

Installing the Snow-Cleanout T ool

No Parts Required

Procedure

g344095

12

7

Checking the T ire Pressure

No Parts Required

Procedure

g344084

8

Checking the Skids and

Scraper

No Parts Required

Procedure

Refer to Checking and Adjusting the Skids and

Scraper ( page 23 ) .

9

Adjusting the

Auger/Impeller Cable

No Parts Required

Procedure

Check and adjust the auger/impeller cable before rst

use; refer to 9 Adjusting the Auger/Impeller Cable

( page 13 ) .

10

Checking the Operation of

the T raction Drive

No Parts Required

Procedure

CAUTION

If the traction drive is not properly adjusted,

the machine may move in the direction

opposite of what you intended, causing injury

and/or property damage.

Carefully check the traction drive and adjust it

properly , if necessary .

1. Start the machine; refer to Starting the Machine

( page 17 ) .

2. Move the speed selector to Position R1; refer to

Operating the Speed Selector ( page 19 ) .

3. Squeeze the left (traction) lever to the handgrip

(Figure 10 ).

13

g00101 1

Figure 10

The machine should move rearward. If the

machine does not move or moves forward,

complete the following:

A. Release the traction lever and shut of f the

machine; refer to Shutting Of f the Machine

( page 22 ) .

B. Disconnect the trunnion from the

speed-selector lever .

C. T urn the trunnion downward (clockwise) on

the speed-control rod.

D. Connect the trunnion to the speed-selector

lever .

4. Release the traction lever .

5. Move the speed selector to Position 1; refer to

Operating the Speed Selector ( page 19 ) .

6. Squeeze the left (traction) lever to the handgrip

(Figure 10 ).

The machine should move forward. If the

machine does not move or moves rearward,

complete the following:

A. Release the traction lever and shut of f the

machine.

B. Disconnect the trunnion from the

speed-selector lever .

C. T urn the trunnion upward (counterclockwise)

on the speed-control rod.

D. Connect the trunnion to the speed-selector

lever .

7. If you made any adjustments, repeat this

procedure until no adjustments are required.

Important: If the machine moves when the

traction lever is in the released position, check the

traction cable; refer to Checking and Adjusting

the T raction Cable ( page 24 ) or take the machine

to an Authorized Service Dealer for service.

Product Overview

g361064

Figure 1 1

1. Handgrip (2) 10. Chute deector

2. Auger/impeller lever

1 1. Discharge chute

3. Lock switch

12. Scraper

4. Speed-selector lever

13. Auger

5. Handwarmer switch

14. Skid (2)

6. Quick Stick

®

discharge-chute control

15. Control panel

7. T raction lever

16. Secondary

battery-compartment

lid

8. Main battery-compartment

lid

17. Snow-cleanout tool

9. Electric-start key 18. Headlight

14

g347780

Figure 12

1. Battery charge lights

3. Key switch in O FF position

2. ECO button

g344092

Figure 13

1. Snow-cleanout tool (attached to the handle)

g292995

Figure 14

1. Battery charger Model

88602 (2 included with

Model 39926)

2. Battery pack Model 88675

(2 included with Model

39926)

Specications

Model W eight Length W idth Height

84.4 kg 142 cm 71 cm 1 17 cm

39926

(186 lb) (56

inches)

(28

inches)

(46

inches)

Battery Pack

Model 88675

7.5 AhBattery pack capacity

405 Wh

Battery manufacturer rating = 60V maximum and 54V nominal.

Actual voltage varies with load.

Battery Charger

Model 88602

T ype

60V MAX Lithium-Ion Battery Charger

Input

120V AC ~2.0A, 60Hz

Output 60V DC 2.0A MAX

Appropriate T emperature Ranges

Charge/store the battery pack

at

5°C (41°F) to 40°C (104°F)*

Use the battery pack at

-30°C (-22°F) to 49°C (120°F)*

Use the machine at

-30°C (-22°F) to 49°C (120°F)*

*Charging time will increase if you do not charge the

battery within this range.

Store the machine, battery pack, and battery charger

in an enclosed clean, dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous.

15

Operation

Before Operation

Installing the Battery Pack

1. Ensure that the vents on the battery packs are

clear of any dust and debris.

2. Lift up the battery-compartment lid.

3. Line up the cavity in the battery pack with the

tongue on the machine and slide the battery

pack into the compartment until it lock into place

(Figure 9 ).

4. Close the battery-compartment lid.

5. Repeat for the other 2 battery cavities (if

needed).

Note: The combined amp hours of all the

installed batteries must add up to 6.0 or greater ,

otherwise the machine can not start.

Note: If the battery-compartment lid does not

close completely , the battery is not fully installed.

g344093

Figure 15

T urning On the Headlight

and Handwarmers

Y ou can turn on the power to the hand warmers and

the headlight before operating the machine; turn the

key to the A CCESSORY position ( Figure 16 ).

In the A CCESSORY position you can also view the state

of charge of each installed battery . The position of

each set of lights corresponds to the related battery

cavity . If the battery state of charge is too low and

needs to be charged, or if there is no battery in the

corresponding cavity , the battery presence light does

not turn on.

g348182

Figure 16

1. State-of-charge lights

3. Key switch in the

ACCESSORY position

2. Battery presence lights

16

Operating the

Handwarmers

Operate the handwarmers as follows:

•Press the switch to the O Nposition to turn on the

handwarmers.

•Press the switch to the O FF position to turn of f the

handwarmers.

g026460

Figure 17

1. On/Of f switch 3. O FF position

2. O Nposition

During Operation

Starting the Machine

Note: Use the battery pack only in temperatures

that are within the appropriate range; refer to

Specications ( page 15 ) .

1. Ensure that the battery pack(s) are installed in

the machine; refer to Installing the Battery Pack

( page 16 ) .

2. Insert the electric-start key into the control panel.

3. T urn the key to the A CCESSORY position.

4. T urn the key to the O Nposition to turn on the

machine ( Figure 18 ).

Note: If the key is turned from O FF position to

the O Ntoo quickly , the machine may not start;

ensure that the key stops briey in the middle

ACCESSORY position.

g347864

Figure 18

1. Key switch in O Nposition

Note: If the machine is turned on and left idling

or operating without the auger engaged for an

extended period, the motor shutof f timeout will

engage, shutting of f the machine. When the

machine shuts of f this way it beeps to indicate

that the timeout was engaged.

Activating ECO Mode

Using ECO mode may extend battery life by reducing

rotor speed; use ECO mode whenever you are

moving light snow , or moving snow a short distance.

Activate ECO mode using the ECO button as shown

in Figure 19 .

g347866

Figure 19

1. ECO mode button

17

Charging the Battery Pack

Important: The battery pack is not fully charged

when you purchase it. Before using the tool for

the rst time, place the battery pack in the charger

and charge it until the LED display indicates the

battery pack is fully charged. Read all safety

precautions.

Important: Charge the battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 15 ) .

Note: At any time, press the battery-charge-indicator

button on the battery pack to display the current

charge (LED indicators).

1. Ensure that the vents on the battery and battery

charger are clear of any dust and debris.

g290533

Figure 20

1. Battery pack cavity

5. LED indicators (current

charge)

2. Battery pack venting areas 6. Handle

3. Battery pack terminals

7. Charger LED indicator

light

4. Battery-charge-indicator

button

8. Charger venting areas

2. Line up the cavity in the battery pack ( Figure 20 )

with the tongue on the charger .

3. Slide the battery pack into the charger until it is

fully seated ( Figure 20 ).

4. T o remove the battery pack, slide the battery

backward out of the charger .

5. Refer to the following table to interpret the LED

indicator light on the battery charger .

Indicator

light

Indicates

Of f

No battery pack inserted

Green

blinking

Battery pack is charging

Green

Battery pack is charged

Red

Battery pack and/or battery charger is over or under

the appropriate temperature range

Red

blinking

Battery pack charging fault*

*Refer to T roubleshooting ( page 29 ) for more

information.

Important: The battery can be left on the charger

for short periods between uses.

If the battery will not be used for longer periods,

remove the battery from the charger; refer to

Storage ( page 28 ) .

18

La page charge ...

Toro Power Max e26 60V Snowthrower Manuel utilisateur

Toro Power Max e26 60V Snowthrower Manuel utilisateur

dans d''autres langues