Bosch HBL5451UC Guide d'installation

HBL53, HBL54, HBL55, HBL56, HBN54,

HBN56, HBN57, HBL84, HBN84, HBL86,

HBN86, HBL87, HBLP75, HSLP75

500/800 Series

Built-In Ovens

Table of Contents

Questions?

1-800-944-2904

www.bosch-home.com

We look forward to hearing from you!

This Bosch Appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Before You Begin . . . . . . . . . . . . . . . . . . . . . 2

Tools and Parts Needed . . . . . . . . . . . . . . . . 2

Parts Included . . . . . . . . . . . . . . . . . . . . . . . . 2

General Information . . . . . . . . . . . . . . . . . . . . 2

Dimensions and Cabinet Requirements . . 3

Removing Packaging . . . . . . . . . . . . . . . . . 3

Preparing Oven . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Determine the Installation Type . . . . . . . . . . . 4

Pre-Assembly of Combination Ovens Prior to

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Installation . . . . . . . . . . . . . . . . . . . 7

Installing the Oven Unit into

the Wall Cabinet . . . . . . . . . . . . . . . . . . . . . 8

For Best Installation . . . . . . . . . . . . . . . . . . . . 8

Removing the Bottom Hinge Oven Door . . . . 8

To replace the oven door: . . . . . . . . . . . . . . . 9

Testing Operation . . . . . . . . . . . . . . . . . . . 10

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Before Calling Service . . . . . . . . . . . . . . . . . 10

Cabinet Dimension Requirements . . . . . . 11

Dimensions for 27” Wall-Mounted Units . . . 11

Dimensions for 30” Wall-Mounted Units . 12

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

English 1

Safety

WARNING:

If the information in this manual is not followed exactly, fire

or shock may result causing property damage or personal

injury.

WARNING:

Do not repair or replace any part of the appliance unless

specifically recommended in the manuals. Improper

installation, service or maintenance can cause injury or

property damage. Refer to this manual for guidance. All

servicing should be done by a qualified technician.

Appliance Handling Safety

Do not lift appliance by door handle. Remove the door for

easier handling and installation. See instructions in Use

and Care Manual.

Unit is heavy and requires at least two people or proper

equipment to move.

Hidden surfaces may have sharp edges. Use caution when

reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with one or more of the following

Standards:

• UL 858, Household Electric Ranges

• UL 923, Microwave Cooking Appliances

• UL 507, The Standard for the Safety of Electric Fans

• CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Electric Safety

Before you plug in an electrical cord, be sure all controls

are in the OFF position.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

Installer - show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Important - Save these instructions for the local electrical

inspector's use.

Before installing, turn power OFF at the service panel. Lock

service panel to prevent power from being turned ON

accidentally.

Refer to data plate for more information. See "Data Plate"

under "Service" for data plate location.

Be sure your appliance is properly installed and grounded

by a qualified technician. Installation, electrical connections

and grounding must comply with all applicable codes.

Related Equipment Safety

Remove all tape and packaging before using the appliance.

Destroy the packaging after unpacking the appliance.

Never allow children to play with packaging material.

Never modify or alter the construction of the appliance. For

example, do not remove leveling legs, panels, wire covers

or anti-tip brackets/screws.

Transport

To avoid damage to the oven vent, use the transport

method shown in the picture below.

Support the bottom of the oven from side to side when

moving it into the installation location. Leave the unit

attached to the shipping pallet until it is in front of the oven

cavity, ready to lift into place.

English 2

Preparation

Before You Begin

Tools and Parts Needed

• Phillips head screwdriver

• Star head screwdriver (T20)

• Measuring tape

• Drill with bit (1/8")

Parts Included

• Phillips head screws (6)

General Information

Power Requirements

The outlet must be properly grounded in accordance with

all applicable codes.

For Best Installation

The oven can be difficult for two people to handle during

installation. It is recommended to have three or more

people available to assist with lifting the unit into place.

Removal of the bottom hinge oven door during installation

(to provide the necessary handholds and to significantly

reduce the unit weight) can be cumbersome unless the

detailed door removal instructions are followed carefully.

Note: Do not attempt to remove the side hinge door (some

models).

Please take time to read and follow the instructions

provided for an improved installation experience.

Checklist

Use this checklist to verify that you have completed each

step of the installation process. This can help you avoid

common mistakes.

___ 1. Before installing the oven, be sure to verify the

cabinet dimensions are correct for your unit and

the required electrical connections are present.

___ 2. Refer to the installation manual for content

regarding Safety, Cabinet Dimensions, Removing

Packaging, Electrical Installation, Testing the

Installation and Customer Service.

___ 3. Remove the oven door(s) to reduce the unit weight

and to provide access to handholds for lifting.

___ 4. Move the oven unit into place in front of the cabinet

opening, leaving the bottom packaging on the unit

to avoid damaging flooring.

___ 5 Remove the T20 screws holding the unit to the

base of the carton (using Star-head screwdriver).

___ 6. If installing a combination unit (oven and

microwave or oven and steam oven) complete the

assembly before installing the unit.

___ 7. Team lift the unit directly into the cabinet cutout

taking care not to pinch fingers or scratch hands or

arms. Make sure the electrical conduit reaches to

the connection point properly.

___ 8. Slide the unit all the way into place, making sure to

route the electrical conduit correctly.

___ 8. Fasten the oven unit to the cabinetry opening with

the screws supplied (using Philips screwdriver).

___ 10. Reinstall the oven door(s) removed in step 2

above.

___ 11. Consult the complete installation instructions and

follow the remainder of the procedures listed,

including performing an operation test.

___ 12. All product literature and accessories (may be

wrapped or boxed) with the oven.

___ 13. INSTALLER - Leave the literature pack and the

accessories with the customer.

English 3

Dimensions and Cabinet Requirements

Cabinet requirements vary depending on the model to be

installed. Please consult the “Cabinet Dimension

Requirements” section at the back of this installation

manual for the details pertaining to your particular model.

All models require:

• 1/4” (6.4 mm) space between the side of the oven and

an adjacent wall or cabinet door when installed at the

end of a cabinet run.

• Installation of 2x4’s extending front to back flush with

the bottom and side of the opening to provide oven

support. This supporting base must be well secured to

the floor/cabinet and must be level.

• The electrical conduit box must be located above the

unit to facilitate connecting and servicing the unit.

• The cabinet base must be flat and capable of

supporting the weight of your oven when in use (varies

by model up to 429 lbs. (195 kg)). See the appropriate

weight for your model in the “Cabinet Dimensions

Requirements” section at the back of this installation

manual.

Removing Packaging

• Cut straps on outside of box.

• Remove cardboard box.

• Remove all top and side cardboard and Styrofoam

braces.

• Place oven in front of cabinets where it is to be

installed.

• Unscrew unit from Left and Right Brackets as show in

“Left and Right Packaging Bracket Removal.”

Left Packaging Bracket Removal

Right Packaging Bracket Removal

Note:

Different models use different packaging materials. Actual

brackets may look differently. Bracket remains in packaging

base. Unit should stay on packaging base until ready to be

lifted into cabinet cutout.

Preparing Oven

Place oven in front of cabinets where it is to be installed.

Rest it on a sturdy support so that it is in line with the

cabinet cutout.

Combination Oven Pre-Assembly

English 4

Installation

Determine the Installation Type

This installation manual provides instructions for the

installation of single ovens, double ovens and combination

ovens (a single oven combined with with microwave or

steam oven).

Parts Provided

Standalone single and double oven units require no

pre-assembly. Unless you are installing a combination

oven, skip over the combination oven pre-assembly

instructions and go directly to “Electrical Installation”

which applies to all ovens.

Pre-Assembly of Combination Ovens

Prior to Installation

Combination ovens (with microwave or steam oven)

require the units to be assembled together prior to installing

the combination unit into the wall cabinet.

Note: The single oven can be installed with a Steam Oven

or with a Microwave Oven. The installation procedure

differs between these. The parts contained in the square

tube parts box are common to both installations.

Parts Provided

Installation with the Microwave Oven

Note: Do not place the oven into the wall cabinet until after

mounting the microwave on it using the universal connector

brackets.

1. The combo service slide assemblies are attached to

the oven spaced to accept the microwave.

2. Install both universal connector brackets using six of

the screws provided. Tighten screws securely, but do

not overtighten.

Note: The universal connector brackets are interchange-

able for the left and right sides of the oven. Be sure the

taller vertical edge of the bracket is positioned to the out-

side of the oven.

Oven Bottom trim (1)

Packed in a plastic sleeve, with mounting screws in a

red bag within the sleeve

Universal connector

bracket (2)

(in parts box on top of

oven)

Screws (16)

(in red bag, inside parts

box on top of oven)

Decorative trim (1)

Packed in bubble wrap, near the oven control panel.

Combo service slide

assembly (2)*

* This part is

preassembled on the

oven to accomodate

attachment of a

microwave.

Combination Oven Pre-Assembly

English 5

3. Install the decorative trim.

4. Place the microwave oven unit on top of the universal

connector brackets and fasten in place using three

screws per side. Tighten the screws securely, but do

not overtighten.

Note: The existing screws in the microwave base help

with alignment. When lowering the microwave into

place on the universal connector bracket, allow these

screw heads to slide into the slots as shown in the

illustration below. The screw nearest the front of the

microwave slides into the base of the slope at the front

of the bracket.

5. Continue with the unit installation in the following

sections on electrical connection and installing the

oven unit into the wall cabinet.

Installation with the Steam Oven

Note: Do not place the oven into the wall cabinet until after

mounting the steam oven on it using the universal connec-

tor brackets.

1. Remove the six screws holding the combo service slide

assemblies to the support bracket. Use a magnetic

screwdriver bit to reach the screws through the large

holes in the tops of the slides.

Position the decorative trim

piece so the flanges with

the holes in them face

away from the oven door.

Align the outer flanges with

the outside of the universal

brackets. Fasten with 1

screw each into the end

hole of the universal

bracket. Tighten screws

securely, but do not

overtighten.

Combination Oven Pre-Assembly

English 6

2. The screw in position A (nearest the inside edge, near

control panel) must be moved to allow the universal

bracket to be postioned there. Remove the inside

screw (A) from the left support bracket and reinsert it

into the third hole (B) from the inside edge of the

support bracket. Repeat for the right support bracket.

3. Reattach the slide assemblies using the holes near the

inside edge of the support bracket. Align the slide

assembly parallel to the edge of the bracket and insert

the first screw in hole (C). Insert all three screws for

each slide assembly. Tighten the screws securely, but

do not overtighten.

Note: When the correct holes are used, the front of the

slide assembly will extend just past the edge of the horizon-

tal support bar. The slide assembly will be about 1/8” (3

mm) from the inside edge of the support bracket.

4. Install the two universal connector brackets to the slide

assemblies using the screws provided. Tighten screws

securely, but do not overtighten.

Note: The universal connector brackets are interchange-

able for the left and right sides of the oven. Be sure the

taller vertical edge of the bracket is positioned to the out-

side of the oven.

5. Install the decorative trim.

6. Place the steam oven unit on top of the universal

connector brackets and fasten in place using two

screws per side. Tighten the screws securely, but do

not overtighten.

Note: The existing screws in the steam oven base help

with alignment. When lowering the steam oven into

place on the universal connector bracket, allow these

screw heads to slide into the slots as shown in the

illustration below. The screw nearest the front of the

steam oven slides into the base of the slope at the front

of the bracket.

Position the decorative trim

piece so the flanges with

the holes in them face

away from the oven door.

Align the inner flanges with

the inside of the universal

brackets. Fasten with one

screw each into the end

hole of the universal

bracket. Tighten screws

securely, but do not

overtighten.

English 7

7. Continue with the unit installation in the following

sections on electrical connection and installing the

oven unit into the wall cabinet.

Connecting the Microwave Oven or Steam

Oven Electrical Conduit to the Single Oven

Note: If installing the oven with a microwave or steam oven

mounted as a combination unit, the microwave oven or

steam oven power cable must be properly attached to the

oven-mounted junction box. This must be done prior to

supplying electric power to the oven unit.

1. Check to be sure there is no electric power supplied to

the oven.

2. Remove the oven mounted junction box cover (located

on the rear top of the oven).

3. Remove the cap from the conduit access hole in the

side of the oven mounted junction box.

4. Guide the four wires from the conduit cable coming

from the microwave or steam oven through the hole in

the oven mounted junction box.

5. Snap the conduit connector into the hole by pressing it

in until it clicks into place.

6. Follow the wiring diagram label and match and connect

each wire by color to the wires attached to the wiring

block inside the oven mounted junction box. Push the

bare end of the wire until it is snug in the wiring block

then tighten down the retaining screw on each wire.

Tighten securely, but do not over tighten.

7. Replace the oven mounted junction box cover and

tighten the two screws holding it in place. Tighten the

screws securely, but do not over tighten.

8. Refer to the Electrical Connection section for further

information to complete the electrical connection of the

combination unit to the main power supply.

Electrical Installation

All model ovens on the front cover of this installation

instruction manual are dual rated, designed to be

connected to either 208 or 240V AC, 60 Hz, 4 wire, single-

phase power supply.

The electrical supply should be a 4-wire single-phase AC.

Install a suitable conduit box (not furnished). An

appropriately-sized, UL-listed conduit connector must be

used to correctly attach the conduit to the junction box.

Important: Local Codes may vary; installation, electrical

connections and grounding must comply with all applicable

local codes.

If local codes permit grounding through the electrical

supply neutral, connect both the white neutral wire and the

green ground wire from the oven to the white neutral

electrical supply wire.

Important: If you have purchased a combination oven unit

(one that includes a microwave or steam oven over the

single oven), see the preceding section “Connecting the

Microwave Oven or Steam Oven Electrical Conduit to the

Single Oven” showing electrical connection of the

combination unit components.

9 WARNING

Disconnect the oven from the electric power supply

before connecting the microwave oven or steam

oven wiring. Failure to do so could result in electrical

shock and injury or death.

Model Circuit Required

208V, 60 Hz 240V, 60 Hz

HBN54, HBN84,

HBL53, HBL54,

HBL84, HBLP4

30 AMP

HBL55

30 AMP 40 AMP

HBN56, HBL56,

HBL57, HBN86,

HBL86, HBL87,

HBLP6, HBLP7,

HSLP7

40 AMP

9 WARNING

Complete the connection of the microwave or steam

oven conduit to the single oven before proceeding

with the unit electrical connection to the main power

supply.

English 8

Electrical Connection to Main Power Supply

The four-wire connection is preferred, but where local

codes permit, the three wire connection is also acceptable.

Four-wire Connection

Ungrounded Neutral

• Connect the red oven wire to the red electrical supply

wire (hot wire).

• Connect the black oven wire to the black electrical

supply wire (hot wire).

• Connect the white neutral oven wire to the white

neutral (not bare or green ground) electrical supply

wire.

• Connect the green ground oven wire to the bare or

green ground electrical supply wire.

Three-wire Connection

Grounded Neutral

• Connect red wire from oven to red wire in junction box.

• Connect black wire from oven to black wire in junction

box.

• Connect both green ground wire and white wire from

oven to white, green or bare neutral wire in junction

box.

The conduit cable, where connected at the oven, swivels.

Rotate conduit cable upward (or downward) and direct

through hole prepared in cabinet to attach to J-Box.

To maintain serviceability, the flex conduit must not be

shortened and should be routed to permit temporary

removal of the oven.

Installing the Oven Unit into

the Wall Cabinet

Note:

Before installing the oven, be sure to verify the cabinet

dimensions and electrical connections.Check that the

cavity is level and plumb for correct installation.

Combination units (ovens with a microwave or steam oven)

have additional installation instructions. Please see the

preceeding section “Pre-Assembly of Combination Ovens

Prior to Installation”.

For Best Installation

The double and combination ovens can be difficult for two

people to handle during installation. It is recommended to

have three or more people available to assist with lifting the

unit into place. It is also recommended to remove the oven

door (bottom hinge models only) to help reduce the unit

weight and provide easier access to the handholds inside

the oven cavity.

Removing the Bottom Hinge Oven Door

Important: Do not attempt to remove the side hinge

door (some models).

For ease of installation, some oven doors may be removed

to reduce the weight of the oven by 30 lbs (14 kg) per door,

before installing into the cabinet. See instructions below.

power supply

junction box

red wires

green or bare

wire

green wire

UL listed

connector

black wires

white wires

cable from

oven

power supply

junction box

red wires

white, bare, or

green wire

white wire

green wire

black wires

UL listed

connector

cable from

oven

9 WARNING

• Make sure oven is cool and power to the oven

has been turned off before removing the door.

Failure to do so could result in burns.

• The oven door is heavy and fragile. Use both

hands to remove the oven door. The door front

is glass. Handle carefully to avoid breaking.

• Grasp only the sides of the oven door. Do not

grasp the handle as it may swing in your hand

and cause damage or injury.

• Failure to grasp the oven door firmly and

properly could result in personal injury or

product damage.

• To avoid injury from hinge bracket snapping

closed, be sure that both levers are securely in

place before removing the door. Also, do not

force door open or closed - the hinge could be

damaged and injury could result.

• Do not lay removed door on sharp or pointed

objects as this could break the glass. Lay on a

flat, smooth surface, positioned so that the

door cannot fall over.

English 9

To remove the oven door:

Placing the Oven Into the Cabinet

Opening

Note: It is recommended to wear gloves and long sleeves

to protect hands and forearms from abrasion and

potential scratches during the lifting process. It is

also recommended to take off watches and jewelry

and to wear work shoes during installation for foot

protection.

When lifting the unit into place avoid grasping the upper

element to avoid damaging it. See the illustration following

for the correct lifting point.

1. The unit and its bottom packaging (pallet) should be

positioned close to and in front of the cabinet opening

prior to beginning to lift the unit into place.

2. Lift or slide unit into the cabinet cutout without allowing

the unit base to contact the flooring.

3. Check that the conduit cable does not fall behind the

unit during installation. It may help to run the conduit

into the area it will be connected to (such as an

overhead or adjacent cabinet) and tape the end down

so it doesn’t fall out while the unit is being slid into

place.

1. Be sure to read the

above WARNING

before attempting to

remove the door.

2. Open the door

completely.

3. Flip levers on hinges

toward you.

4. Holding the door firmly

on both sides and

using both hands,

close the door gently

until it stops against

the levers, about 30º

from the closed

position.

5. Carefully lift the door

up and out of the

hinge slots. Hold

firmly; the door is

heavy.

6. Place the door in a

convenient and stable

location unitl you are

ready to reinstall it.

9 CAUTION

To avoid damage to the door do not lift, pull or push

the unit during installation by using the oven door

handle as a gripping point.

English 10

4. Guide the unit straight back into the cabinet cutout.

Note: Be careful not to crimp the flexible conduit

between the oven and the cabinet back wall. If

necessary, guide the flexible conduit into the wall or

cabinet access hole so it doesn’t prevent the unit from

being pushed all the way into the cabinet opening. The

oven should be straight and level, not crooked.

5. Install the oven bottom trim while the door is removed

and the unit is in place. (Do not push the unit all the

way in, leave about 1 inch extending from the front of

the cabinet). Use two of the screws provided in the red

bag included with the trim piece.

3. Push the unit straight in until the oven trim is flush with

the front of the cabinet trim.

4. Install supplied screws through tap holes in trim. (2

screws for single ovens, 4 screws for double/combo

ovens).

To replace the oven door:

1. Align holes in trim ends with holes at bottom of oven.

2. Insert screws and tighten firmly. Do not overtighten.

1. Hold the door firmly in

both hands.

2. Hold the door at a 30º

angle from the closed

position and insert

hinges into the slots.

You may need to rock

the door forward and

backward slightly to

seat the hinge feet.

3. The door may need to

be removed and re-

inserted until the

hinges sit correctly in

the slots.

4. Open door all the way

to expose hinges,

levers, and slots.

5. Push levers forward

and down until seated

on the bracket.

6. Close and open door

slowly to be sure it is

correctly and securely

in place. Door must be

straight, not crooked.

English 11

Testing Operation

1. Turn on power at the breaker.

2. Test the oven mode.

Select the BAKE mode. See the Use and Care Manual

for detailed operation instructions.

3. Verify that the oven light comes on and the oven begins

to preheat.

4. Test the door lock.

Set the SELF CLEAN mode. Confirm that the door

locks when the lock icon appears in the display.

5. If installing a double oven, test the second oven as

well.

6. If any of the tests do not result as explained above,

contact Bosch service for assistance. Otherwise, the

installation is complete at this time.

Service

Before Calling Service

See Use and Care Manual for troubleshooting information.

Refer to the Warranty in the Use and Care Manual.

To reach a service representative, see the contact

information at the front of the manual. Please be prepared

with the information printed on your product data plate

when calling.

Data Plate

The data plate shows the model and serial number. Refer

to the data plate on the appliance when requesting service.

The data plate is located on the underside of the control

panel.

Data

Plate

English 12

Cabinet Dimension Requirements

Dimensions for 27” Wall-Mounted Units

Single Oven 27”

* For single ovens installed in a wall cabinet, the junction

box may be located above or beneath the unit within

reach of the power cable.

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box can be installed above or to the right of the

unit, within range of the power conduit.

The cabinet cavity must be plumb and the base must be flat

and level and capable of supporting a weight of at least 193

lbs (87 kg).

Double Oven 27”

* For single ovens installed in a wall cabinet, the junction

box may be located above or beneath the unit within

reach of the power cable.

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

English 13

The cabinet cavity must be plumb and the base must be flat

and level and capable of supporting a weight of at least 361

lbs (164 kg).

Single Oven, Undercounter 27”

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

The cabinet base must be flat and capable of supporting a

weight of at least 193 lbs (87 kg).

.

Dimensions for 30” Wall-Mounted Units

Single Oven 30”

* For single ovens installed in a wall cabinet, the junction

box may be located above or beneath the unit within

reach of the power cable.

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be installed either above or below the

unit. If the conduit box is installed below the unit, a 2”

diameter hole or space is required between the back wall

and the right rear of the 2x4 supports.

The cabinet cavity must be plumb and the base must be flat

and level and capable of supporting a weight of at least 212

lbs (96 kg).

English 14

Double Oven 30”

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

The cabinet cavity must be plumb and the base must be flat

and level and capable of supporting a weight of at least 390

lbs (177 kg).

Combination Oven and Microwave 30”

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

Top View Side View

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

The cabinet cavity must be plumb and the base must be flat

and level and capable of supporting a weight of at least 310

lbs (141 kg).

English 15

Combination Oven and Steam Oven 30”

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

The cabinet cavity must be plumb and the base must be flat

and level and capable of supporting a weight of at least 429

lbs (195 kg).

Single Oven, Undercounter 30”

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 1/4” space between the side of the

oven and the wall/door.

For oven support, install 2x4’s extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

The cabinet cavity must be plumb and the base must be flat

and level and capable of supporting a weight of at least 212

lbs (96 kg).

English 16

English 17

La page charge ...

Bosch HBL5451UC Guide d'installation

Ce manuel convient également à

Bosch HBL5451UC Guide d'installation

dans d''autres langues

Documents connexes

Autres documents