Paxton
ins-20602
Panel mount readers
1
1
2
Mounting and wiring
1 2
1
2
Installation guidelines
• The panel mount reader is designed to t into a door entry panel.
It ts behind a reader aperture of industry standard size (40 mm x
40 mm) and is supplied with a polycarbonate window to match.
See page 1 for installation.
• Holes are provided in each corner to t over 4 posts set in a
49 mm square formation. Fixings are not provided as they will
normally be supplied with the panel.
Technical Help
1 - Readers/Keypads not working.
• Software settings - Conrm that the settings of the reader or
keypad are correct.
• Connections - Check the wiring and integrity of the connectors. If
possible, test this reader on the other port.
• Extended cable - Belden 9540/5306FE or General Cable C0745A
/E2038S should be used up to a maximum of 328 feet. Twisted
pair alarm cable should not be used. To conrm that an extended
reader cable is not at fault, wire the reader directly to the port.
• Supply voltage - Conrm that the voltage is within specication.
(see table)
• User token - Conrm that the user token used for testing is OK by
presenting it to a known working reader.
• Interference - Conrm whether the reader works when tested ‘in
hand’ and not mounted on the wall.
• PROXIMITY readers should not be mounted back to back or close
to other RF devices.
2 - Net2. What to do if a user has no access - Check the reader LED’s
when a card is shown.
• No LED’s - the reader has no power.
• No change in display - try the card on a known working reader. If
there is still no response, replace the card.
• Green LED ashing when a card is presented; check relay 1 LED to
check for activity and also the lock wiring.
• Red LED is ashing when a card is presented; check the validity of
the user at the PC.
• Check user’s access level and ensure they should have access by
clicking on Current Validity.
• Check the ‘Expires end’ date and conrm this has not been past.
3
390-135
110mA
390-530
110mA
Current
@ 12V DC
Operating
temperature
Waterproof
HID
compatible
Handsfree
Mounted on
metal surface
-40°C - +66°C
-40°F - +151°F
Reinstate the ACU from the doors screen. Select the ACU’s you wish to
reinstate and then click OK.otherwise the Desktop reader option will not
be available.
3 - Switch2 - Adding an additional card pack.
You need to be in possession of the original enrolment card. Present
the original enrolment card to the reader and the Amber LED will
ash, Green & Red LEDs will be o, then present the Enrolment card
from the new card pack; the reader will beep and all LEDS will be lit.
The additional cards will now be valid. Repeat this with each reader and
with any additional card packs. Any valid enrolment card can be used
to add further packs. This is the same for enrolling function card packs
onto a system.
4 - Switch2 - How to reset the controller.
1. Disconnect the power and remove the wires from the Green and
Mauve terminals
2. Insert a wire link between the Green and Mauve terminals
3. Reconnect the power (the unit will bleep 4 times)
4. Disconnect the power and remove the link wire, reconnect the Green
and Mauve wires
5. Reconnect the power (the unit will bleep 3 times per second). The
unit is ready to be enrolled.
3 4
390-135
110mA
390-530
110mA
Current
@ 12V DC
Operating
temperature
Waterproof
HID
compatible
Handsfree
Mounted on
metal surface
-40°C - +66°C
-40°F - +151°F
Specications
5
+44 (0)1273 811011
paxton.support
877.438.7298
usapaxton.support
+31 (0)76 3333 999
paxton.benelux.support
+32 (0) 78485147
paxton.benelux.support
+49 (0) 251 2080 6900
paxton.gmbh.support
+33 (0)1 57 32 93 56
paxton.support
+27 (0) 21 4276691
paxton.support
8000 3570 3783
paxton.support
+52 55 5351 3667
paxton.soporte
+57 1508 8198
paxton.soporte
+44 (0)1273 811011
paxton.support
5 6
+44 (0)1273 811011
paxton.support
877.438.7298
usapaxton.support
+31 (0)76 3333 999
paxton.benelux.support
+32 (0) 78485147
paxton.benelux.support
+49 (0) 251 2080 6900
paxton.gmbh.support
+33 (0)1 57 32 93 56
paxton.support
+27 (0) 21 4276691
paxton.support
8000 3570 3783
paxton.support
+52 55 5351 3667
paxton.soporte
+57 1508 8198
paxton.soporte
+44 (0)1273 811011
paxton.support
Ce dispositif est conforme à la section 15 du règlement de la FCC. Le fonctionnement est soumis aux deux
conditions suivantes : (1) ce dispositif ne doit pas créer d'interférences nuisibles et (2) ce dispositif doit accepter
toute interférence reçue, y compris des interférences qui peuvent causer un fonctionnement non souhaité. Tout
changement ou modication non agréé par la partie responsable de la mise en conformité peut entraîner une
interdiction d'utilisation de l'équipement.
Conformité et limitations du produit
Ce dispositif est conforme au(x) standards RSS de l'industrie Canadienne sans-licence. Le fonctionnement est
soumis aux deux conditions suivantes : (1) ce dispositif ne doit pas créer d'interférences nuisibles et (2) ce dispositif
doit accepter toute interférence reçue, y compris des interférences qui peuvent causer un fonctionnement non
souhaité.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or modications not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment.
To comply as a UL listed installation, the following conditions must apply:-
• Server based functions (Antipassback, Time and Attendance, etc) have not been evaluated by UL and
cannot be used for UL 294 installations.
• Where an equivalent cable / wire is used it must be ‘ UL Listed ‘All interconnecting devices must be UL
Listed.
• The use of Wiegand readers and the conguration software has not been evaluated by ‘UL’
• For CAN/ULC-S319 installations, terminals, leads and wiring methods must comply with CSA, C22.1,
Canadian electrical code, Part 1, safety standards for electrical installations.
• The use of any add-on, expansion, memory or other module manufactured or supplied by the
manufacturer’s representative will invalidate the CAN/ULC-S319 certication.
• Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and
the authorities having jurisdiction.
Pour que l’installation répond aux normes UL, les conditions suivantes sont applicables:-
• Les fonctions serveur (Antipassback, Pointage, etc.) n’ont pas été évalué par l’UL et ne peuvent pas être
utilisé pour les installations UL294.
• L’utilisation des lecteurs Wiegand et le logiciel de conguration n’ont pas été évalués par ‘UL’
• Quand un cable équivalent est utilisé, il doit être ‘listé UL’Tout appareil d’interconnexion doit être listé UL
• Pour les installation CAN/ULC-S319, les terminaux, câbles et méthodes de câblage doivent être en accord
avec CSA, C22.1, code électrique canadien, Partie 1, standards de sécurité pour les installations électriques.
• L’utilisation de tout rajout, extension, mémoire ou module fabriqué ou fourni par le représentant du
fabricant invalidera la certication CAN/ULC-S319
• Les méthodes de câblage doivent être en accord avec le code nation électrique (ANSI/NFPA70), codes
locaux et les autorités ayant la juridiction.
North America:- Product compliance and limitations
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
These products are not suitable for retail sale. All warranties are invalid if these products are not installed by
a competent person.
FCC Compliance
Conformité FCC
http://paxton.info/1606
Paxton Access Ltd hereby declares that this product is in conformity with all the essential
requirements of the Directive 2014/53/EU.
https://www.paxton-access.co.uk/docs/Instructions/ins-181.pdf
The full declaration of conformity is available on request. Contact details are provided at:
http://paxton.info/596
© Paxton Ltd 1.0.3
Made in the UK
09/06/2017
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
Documents connexes
-
Paxton ins-20102 Mode d'emploi
-
-
-
-
-
-
-
-
-