Sony CDP-CX260 Manuel utilisateur

3-862-564-21 (1)

 1998 by Sony Corporation

CDP-CX260

Compact Disc

Player

EN

F

ES

P

Operating Instructions

Mode d’emploi

Manual de instrucciones

2

EN

Welcome!

Thank you for purchasing the Sony

Compact Disc Player. Before operating

the unit, please read this manual

thoroughly and retain it for future

reference.

About This Manual

The instructions in this manual are for

models CDP-CX260.

Conventions

• Instructions in this manual describe

the controls on the player.

You can also use the controls on the

remote if they have the same or

similar names as those on the player.

• The following icons are used in this

manual:

Indicates that you can do the

task using the remote.

Indicates hints and tips for

making the task easier.

This equipment is intended for home

entertainment purposes only. The

warranty shall be invalidated if used

in commercial environments, such as

by disc jockeys, etc., even within the

Warranty Period.

WARNING

To prevent fire or shock

hazard, do not expose

the unit to rain or

moisture.

To avoid electrical shock,

do not open the cabinet.

Refer servicing to

qualified personnel only.

The laser component in this product

is capable of emitting radiation

exceeding the limit for Class 1.

This appliance is classified as a CLASS 1

LASER product. The CLASS 1 LASER

PRODUCT MARKING is located on the

rear exterior.

The following caution label is located

inside of the unit.

For the customers in Canada

CAUTION

TO PREVENT ELECTRIC SHOCK,

DO NOT USE THIS POLARIZED AC

PLUG WITH AN EXTENSION

CORD, RECEPTACLE OR OTHER

OUTLET UNLESS THE BLADES

CAN BE FULLY INSERTED TO

PREVENT BLADE EXPOSURE.

3

EN

TABLE OF CONTENTS

Getting Started

Unpacking ............................................................................................................................. 4

Hooking Up the System ...................................................................................................... 5

Setting up the remote .......................................................................................................... 6

Connecting Another CD Player ......................................................................................... 9

Inserting CDs...................................................................................................................... 10

Playing a CD .......................................................................................................................... 12

Playing CDs

Using the Display .............................................................................................................. 14

Locating a Specific Disc .................................................................................................... 16

Specifying the Next Disc to Play ..................................................................................... 18

Locating a Specific Track or a Point in a Track ............................................................. 18

Playing Repeatedly ............................................................................................................ 20

Playing in Random Order (Shuffle Play) ....................................................................... 20

Creating Your Own Program (Program Play) ............................................................... 21

Playing Using a Timer....................................................................................................... 25

Controlling Another CD Player (Advanced Mega Control) ....................................... 26

Fading In or Out................................................................................................................. 27

Playing Alternately (No-Delay Play/X-Fade Play) ...................................................... 28

Storing Information About CDs (Custom Files)

What You Can Do With the Custom Files ..................................................................... 29

Labeling Discs (Disc Memo)............................................................................................. 29

Storing Custom File Information Using a Keyboard.................................................... 32

Storing Specific Tracks (Delete Bank) ............................................................................. 32

Grouping Discs (Group File)............................................................................................ 33

Storing Your Favorite Tracks (Hit List) .......................................................................... 35

Additional Information

Precautions ......................................................................................................................... 38

Notes on CDs...................................................................................................................... 38

Troubleshooting ................................................................................................................. 39

Specifications ...................................................................................................................... 39

Index .......................................................................................................................................... 40

EN

Getting Started

4

EN

Getting Started

Unpacking

Check that you received the following items:

• Audio cord (1)

• CD booklet holders (2) and label (1)

• DC-cable (1)

• Monaural (2P) mini-plug cord (connecting cord for

the transmitter/receiver) (1)

• Remote commander (remote) (1)

• Sony LR6 batteries (3)

• Transmitter/receiver (1)

How to use the CD booklet holder

The CD booklet holder helps you locate discs easily.

After you have inserted discs into the player, you can put

the CD booklet (which comes with a CD) into the

supplied holder. Put two CD booklets facing back to back

into a pocket. Stick the number label on each pocket,

matching the number of the disc slot where you have

inserted the disc. You can put up to 200 CD booklets into

the holders.

Inserting batteries into the remote

You can control the player using the supplied remote.

Insert three size AA (LR6) batteries (supplied) by

matching the + and – ends on the batteries to the

diagram inside the battery compartment.

Insert the negative (–) end first, then push in and down

until the positive (+) end clicks into position.

When using the remote, point it at the remote sensor g

on the player.

When to replace batteries

If i flashes in the remote’s display, replace all the

batteries with new alkaline batteries. Use of battery types

other than alkaline batteries, such as manganese

batteries, may not last longer than the alkaline batteries.

The loaded memory in the remote will be retained for a

few minutes while you replace the batteries.

Notes

• Do not leave the remote near an extremely hot or humid

place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or leave

too near lighting apparatuses. Doing so may cause a

malfunction.

• If you do not use the remote for an extended period of time,

remove the batteries to avoid possible damage from battery

leakage and corrosion.

Playing CDsGetting Started

Getting Started

5

EN

Hooking Up the System

Overview

This section describes how to hook up the CD player to

an amplifier. Be sure to turn off the power of each

component before making the connections.

What cords will I need?

Audio cord (1) (supplied)

White

(L)

Red

(R)

White

(L)

Red

(R)

Hookups

When connecting the audio cord, be sure to match the

color-coded cords to the appropriate jacks on the

components: Red (right) to Red and White (left) to

White. Be sure to make connections firmly to avoid

hum and noise.

CD player

Amplifier

• If you have a digital component such as a digital

amplifier, D/A converter, DAT or MD

Connect the component via the DIGITAL OUT (OPTICAL)

connector using an optical cable (not supplied). Take off the

cap and plug in the optical cable.

CD player

DIGITAL OUT

(OPTICAL)

COMMAND MODE

To S-LINK/CONTROL A1

jack

Amplifier

To line output (L) To line output (R)

To an AC outlet

: Signal flow

To audio input

POC-15

Optical cable (not supplied)

CD player

Digital component

Note

When you connect via the DIGITAL OUT (OPTICAL)

connector, noise may occur when you play CD software

other than music, such as a CD-ROM.

To an AC outlet

LINE2ND CD

IN OUT

L

R

L

R

INPUT

CD

L

R

DIGITAL OUT

OPTICAL

DIGITAL INPUT

OPTICAL

• To connect the transmitter/receiver

Connect the transmitter/receiver via the TO TMR-IA10 jack

using a DC-cable (supplied) and via the S-LINK CONTROL

A1 jack using a monaural (2P) mini-plug cord (supplied).

To DC IN 6V

Transmitter/receiver

To TMR-IA10

To S-LINK/CONTROL A1

jack

DC-cable (1) (supplied)

CD player

Transmitter/receiver

DC OUT 6V

(

TRANSMITTER RECEIVER

)

TO TMR - I A10

S - L I NK

CONTROL A1

DC IN 6V

CONTROL A1

Getting Started

6

EN

Setting Up the Remote

This section describes how to prepare the supplied

remote for operation.

Press OPERATE on the transmitter/receiver to turn it

on and press I/u on the player to turn the player on.

If the following message appears in the remote’s

display while setting up the remote, point the remote

at the player and the transmitter/receiver as illustrated

below.

Note that the display disappears automatically if you

don’t proceed for more than a few moments.

Setting the voltage selector (voltage

selector equipped models only)

Check that the voltage selector on the rear panel of the

player is set to the local power line voltage. If not, set

the selector to the correct position using a screwdriver

before connecting the AC power cord to a wall outlet.

Connecting the AC power cord

Connect the AC power cord to a wall outlet.

Note on placement of the player and the

transmitter/receiver

Be sure to place the player in a flat, horizontal place.

If the player is left in a slanted position, it may cause a

malfunction or damage the player.

Be sure to place the transmitter/receiver on the top left

corner, facing forward, otherwise the player may not

operate correctly with the remote.

220 - 240 V110 - 120 V

If you have a Sony component with the CONTROL A1

jack

Connect the component via the CONTROL A1 jack. You

can simplify the operation of audio systems composed of

separate Sony components. For details, refer to the

supplementary “S-Link

TM

/CONTROL-A1 Control

System” instructions.

CONTINUE

PROGRAM

MEMO SCAN

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

DISC

SKIP

SHUFFLE

REPEAT

TIME/TEXT

MENU

Easy scroll

key

30°

OPERATE

an' t receive

elPaseturn

to a main unit

hi

C

tsREMOTE

I/u

Playing CDsGetting Started

Getting Started

7

EN

Memo sea r ch

Program play

Program input

Group select

CD1

Player check

Memo l oad i ng

Memo r y c l ea r

Contrast adjust

CD1

aster player

= CD1/200discs

M

CD1

aster player

= CD1/200discs

= CD3/ 51discs

nd

M

2 player

CD1

How to move the cursor in the remote’s

display

To move the cursor down, push the Easy scroll key

downward as illustrated below.

To move the cursor up, push the Easy scroll key

upward as illustrated below.

Memo sea r ch

Program play

Program input

Group select

CD1

Loading the Disc Memo

1 Press MENU.

2 Move the cursor (”) to “Set up” by using the Easy

scroll key, then press the Easy scroll key.

Player check

Memo l oad i ng

Memo r y c l ea r

Contrast adjust

CD1

2 Move the cursor (”) to “Set up” by using the Easy

scroll key, then press the Easy scroll key.

3 Move the cursor to “Player check,” then press the

Easy scroll key.

The display shows the disc data in the player after

“Now player checking...” appears.

When you connect another CD player, the disc

data in the second CD player also appears.

Storing disc data in the remote

1 Press MENU.

Note the $ mark indicates that the menu

continues.

Press the Easy scroll key downward to see the

next items.

(Continued)

Getting Started

8

EN

Adjusting the display contrast of the

remote

1 Press MENU.

Turning off the LCD back light

You can conserve the remote’s power by turning off

the LCD (Liquid Crystal Display) back light.

1 Press MENU.

2 Move the cursor (”) to “Back light mode” by using

the Easy scroll key, then press the Easy scroll key.

3 Move the cursor to “OFF,” then press the Easy

scroll key.

Note

If you erase all the data stored in the remote (page 9), follow

the procedure above to turn the back light off again .

Memo sea r ch

Program play

Program input

Group select

CD1

Memo sea r ch

Program play

Program input

Group select

CD1

CD Back Light

OFF

ON

L

CD1

ster player

memo LOADING

S

Ma

DI C120

CD1

Al l memo data

Master player

Group memo

CD1

3 Move the cursor to “Memo loading,” then press

the Easy scroll key.

When you connect another CD player, “2nd

player” also appears.

4 When you want to load all Disc Memos (the master

player’s, second CD player’s*, and both player’s

Group Memo data), move the cursor to

“All memo data,” then press the Easy scroll key.

The remote starts reading all memo data. The

loading time may take a few moments. Point the

remote at the player while loading the data.

* The second CD player’s Disc Memo data must be

loaded to the master player before you load the

data to the remote.

When you want to load each Disc Memo data

independently, move the cursor to the data you

want to load, then press the Easy scroll key.

5 When the remote finishes reading the data,

“Memo loading complete” appears in the remote’s

display.

2 Move the cursor (”) to “Set up” by using the Easy

scroll key, then press the Easy scroll key.

3 Move the cursor to “Contrast adjust,” then press

the Easy scroll key.

4 Adjust the contrast by pressing the Easy scroll key

up or down and holding until the desired level of

contrast is attained.

5 Press the Easy scroll key.

Player check

Memo l oad i ng

Memo r y c l ea r

Contrast adjust

CD1

ONTRAST

ADJUST

adjus

on

C

ctrast

t

CD1

Playing CDsGetting Started

Getting Started

9

EN

Erasing all data stored in the remote

1 Press MENU.

2 Move the cursor (”) to “Set up” by using the Easy

scroll key, then press the Easy scroll key.

3 Move the cursor to “Memory clear,” then press the

Easy scroll key.

4 If you want to erase all stored data, move the

cursor to “yes,” then press the Easy scroll key.

5 “All memory clear!” appears in the display when

all data is erased.

Memo sea r ch

Program play

Program input

Group select

CD1

Player check

Memo l oad i ng

Memo r y c l ea r

Contrast adjust

CD1

Al l memory

clear OK?

yes

no

CD1

Al l memory

clear OK?

yes

no

CD1

CDP-CX260

CDP-CX200, etc.

To an AC outlet

: Signal flow

To audio input

To LINE OUT

Amplifier

To an AC outlet

COMMAND MODE

To 2ND CD IN

To S-LINK/CONTROL A1

To audio output

To CONTROL A1

(Continued)

Connecting Another CD Player

If you have a Sony CD player in which 5, 50, or 200

discs can be inserted and which is equipped with the

CONTROL A1 jack and the command mode of that

player can be set to CD 3, you can control that player as

the second player with this unit. After connecting this

unit and an amplifier, follow the procedure below.

Be sure to turn off the power of each player before

making this connection.

Getting Started

10

EN

Inserting CDs

You can insert up to 200 discs into this player.

1 Press I/u to turn on the player.

2 Open the front cover by pressing § OPEN/

CLOSE.

I/u

§ OPEN/CLOSE

JOG

Rotary table

Loading position

Playing position

What cords will I need?

• Audio cord (1) (Use the cord supplied with the player to be

connected.)

• Monaural (2P) mini-plug cord (1) (not supplied)

1 Connect the players with an audio cord (see also

“Hookups” on page 5).

2 Connect the players with a monaural (2P) mini-

plug cord.

CDP-CX260

For details on this connection, refer to the

supplementary “S-Link

TM

/CONTROL-A1 Control

System” instructions.

3 Set the COMMAND MODE selector of this player

to CD 1 or CD 2, and set the command mode of the

second player to CD 3.

For details on how to operate the second player,

see “Controlling Another CD Player” on page 26

and “Playing Alternately” on page 28.

4 Connect the AC power cord of both players to AC

outlets.

Notes

• Do not connect a player other than that you intend to use as

the second player to the 2ND CD IN jacks of this player.

• When connecting a second CD player, do not connect the

DIGITAL OUT (OPTICAL) connector of this unit to the

amplifier.

• If you connect another CD player after you have already set

up the remote, follow “Setting Up the Remote” on page 6 to

set up the remote again.

• To operate the second CD player with the remote, press

PLAYER SELECT on the remote to select the second player.

LINE2ND CD

IN OUT

L

R

L

R

LINE OUT

L

R

CONTROL A1

S-LINK

CONTROL A1

CDP-CX200, etc.

COMMAND MODE

CD

132

Playing CDsGetting Started

Getting Started

11

EN

The disc number at the loading position appears in

the display*. If the disc has a Disc Memo (see page

29), the Disc Memo appears instead of the disc

number. As you turn the JOG dial, the disc number

or the Disc Memo changes.

You can classify discs into eight groups by using

the Group File function. This feature lets you easily

find the disc you want to play. For details, see

“Grouping Discs” on page 33.

* If you have already inserted discs, the disc number at

the playing position appears. When you turn the JOG

dial, the displayed disc number changes to the one at

the loading position.

3 Turn the JOG dial until you find the disc slot

where you want to insert a disc, while checking the

disc number (written beside every slot and also

indicated in the display).

After inserting the disc, you can input the original

disc titles instead of the disc numbers (see

“Labeling Discs” on page 29) to locate it easily

whenever you want to play it.

4 Insert a disc with the label side facing right.

Disc slot at the loading position

Disc number

Disc number or the Disc Memo

ALL

*DISC-20*

DISCS

CD1

02

DISC

Removing CDs

After following Steps 1 to 3 of “Inserting CDs” on page

10, remove the discs. Then close the front cover.

The rotary table turns and the disc slot at the

loading position is set to the playing position.

Always keep the front cover closed except when

inserting or removing discs.

The supplied CD booklet holders help you locate a

disc easily

You can store up to 200 CD booklets. Insert a booklet and

stick the number label on the pocket matching the

number of the disc slot where you have inserted the disc.

5 Repeat Steps 3 and 4 to insert more discs.

6 Close the front cover by pressing § OPEN/

CLOSE.

With the label side

facing right

ALL DISCS

CD1

20

DISC

SONYHITS

Notes

• Do not insert an empty 8 cm (3-inch) CD adaptor (CSA-8). It

may damage the player.

• Do not attach anything such as seals or sleeves to CDs. It

may damage the player or the disc.

• If you drop a disc into the player and/or the CD won’t

go into the slot correctly, consult your nearest Sony

dealer.

• When transporting the player, remove all discs from the

player.

• Make sure to insert the disc into the slot at a right angle

to the rotary table. If the disc is not put in straight, it

may damage the player or the disc.

• Make sure the rotary table comes to a complete stop

before inserting or removing discs.

The front panel closes automatically when you press

·. Be careful not to put your hand into the player after

pressing · otherwise your hand may be caught in the

front panel.

Basic Operations

12

EN

Playing a CD

23

1

2

• See page 5 for hookup

information.

• Make sure you have inserted the

discs correctly as indicated on

page 10.

• You can play all the tracks on a

disc in the original order

(Continuous Play). You can also

play up to 200 discs

consecutively.

You can turn on the player

by pressing I/u on the

remote

Turn on the amplifier and select the CD player position.

Press I/u to turn on the player.

Press CONTINUE to select ALL DISCS or 1␣ DISC Continuous

Play mode.

Each time you press CONTINUE, “ALL DISCS” or “1␣ DISC”

appears alternately in the display.

3

When you select

ALL DISCS

1 DISC

The player plays

All discs in the player consecutively in the order of

disc number. Empty disc slots are skipped.

Only the one disc you have selected

Turn the JOG dial until the desired disc number or Disc Memo

(see page 29) appears in the display to select the first disc (ALL

DISCS) or the disc you want (1␣ DISC).

4

4/5

ALL DISCS

CD1

20

DISC

*DISC-20*

5

STANDBY

I / u

TIMER

OFF PLAY

KEY BOARD

KEYBOARD

CONTINUE

GROUP 1

GROUP 5

SHUFFLE

GROUP 2

GROUP 6

PROGRAM

GROUP 3

GROUP 7

REPEAT

GROUP 4

GROUP 8

TIME/TEXT

HIT LIST

GROUP FILE

MEGA CONTROL

FADER NO DELAY

X-FADE

MEMO SEARCH

INPUT

DISC/CHARACTER

PUSH ENTER

OPEN/CLOSE

AMS

CHECK CLEAR

Basic Operations

13

EN

5

Push the JOG dial or press · to start playing.

The selected disc is set to the playing position, and the player

plays all the discs from the selected one (ALL DISCS) or all the

tracks once (1␣ DISC).

Adjust the volume on the amplifier.

To stop playback

Press p.

When you turn off the player

The player remembers the

last playing disc and the

play mode (Continuous,

Shuffle, or Program (see

pages 20 and 21)). When you

turn on the player again,

therefore, the player plays

the same disc in the same

play mode.

§ OPEN/CLOSE

≠/±

·P p

To

Pause

Resume playing after pause

Go to the next disc

Go back to the preceding disc

Go to the next track

Go back to the preceding track

Stop playing and remove the disc

You need to

Press P

Press P or ·

Press DISC SKIP + once.

Hold down the button to skip other discs.

Press DISC SKIP – once.

Hold down the button to skip other discs.

Press ±

Press ≠

Press § OPEN/CLOSE

JOG

STANDBY

I / u

TIMER

OFF PLAY

KEY BOARD

KEYBOARD

CONTINUE

GROUP 1

GROUP 5

SHUFFLE

GROUP 2

GROUP 6

PROGRAM

GROUP 3

GROUP 7

REPEAT

GROUP 4

GROUP 8

TIME/TEXT

HIT LIST

GROUP FILE

MEGA CONTROL

FADER NO DELAY

X-FADE

MEMO SEARCH

INPUT

DISC/CHARACTER

PUSH ENTER

OPEN/CLOSE

AMS

CHECK CLEAR

Playing CDs

14

EN

Playing CDs

Using the Display

You can check information about the disc using the

display.

p

JOGTIME/TEXT

Checking the total number and playing

time of the tracks

Select the disc you want to check, and press

TIME/TEXT .

The display shows the current disc number, total

number of tracks, and total playing time of the disc.

When you want to check another disc

Press DISC SKIP +/– on the remote in the stop mode to

select the disc you want to check. The total number of

tracks and the total playing time of the selected disc

appear momentarily.

Current disc number

Total number of tracks

Total playing time

Display information of the playing disc

While playing a disc, the display shows the current disc

number, track number, playing time of the track, and

the next disc number.

Current disc number

Next disc number

Current track number

Playing time of the track

HIGH-LIGHT

INPUT

GROUP

ENTER DEL

CLEAR

DISC SKIP

CHECK

NO DELAY

SPACE X-FADE

CAPS HIT LIST

DISC HIGH-LIGHT

3

DEF MEMO INPUT

6

MNO

9

WXY

2

ABC&!?

5

JKL

8

TUV

10/0

10

QZ

1

4

GHI

7

PRS

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

While in stop mode

While in play mode

Remote’s display information

While in stop mode, the remote’s display shows the

current disc number. While in play mode, the current

track number also appears.

isc20

* DISC-

2

*

0

D

CD1

isc20

* DISC-20*

( TRACK1 )

ra

D

Tck1

CD1

ALL DISCS

CD1

83

DISC

TRACK

MIN

SEC

20 1 0.28

ALL DISCS

CD1

20

DISC

TRACK

MIN

SEC

20 10 60.48

Note

While in stop mode, the Disc Memo appears if you labeled the

disc (see page 29).

While in play mode, the track title appears (up to the 13th

character) when you select a CD TEXT disc (see pages 15 and

29).

Playing CDsGetting Started

Playing CDs

15

EN

Display information while playing a disc

Each time you press TIME/TEXT, the display shows

the information as shown below.

The current disc

number, track

number and

playing time

appear.

Press TIME/TEXT.

The current track

title appears.

This information also appears when

the player locates the track.

To play disc highlights Z

Some CD TEXT discs have a feature to play only the

highlights of the discs.

During stop mode, press HIGH-LIGHT on the remote to start

playing disc highlights.

“Hi LIGHT” flashes while playing disc highlights.

If you press HIGH-LIGHT while selecting discs without this

feature, “NO HIGHLIGHT” appears in the display.

ALL DISCS

CD TEXT

CD1

DISC

TRACK

MIN

SEC

ALL DISCS

CD TEXT

CD1

TRACK

13

12 1 1.52

13

HitechBlues

Checking the information of CD TEXT discs

CD TEXT discs have information, such as the disc titles

or artist names, memorised in a blank space on the

discs where, on normal discs, there is no information.

The display shows the CD TEXT information of the

disc so that you can check the current disc title, artist

name and track title. When the player detects a CD

TEXT disc, “CD TEXT” appears in the display. If your

CD TEXT disc has multi-language capacity, “MULTI

CD TEXT” appears in the display. If you want to check

the information in another language, refer to “Selecting

the language of the CD TEXT information” on page 15.

Display information in stop mode

The display shows the disc title. When you press

TIME/TEXT, the artist name scrolls in the display. If

you press TIME/TEXT again, the display shows the

current disc number, total number of tracks, and total

playing time of the disc momentarily. Then the display

shows the disc title again.

Selecting the language of the CD TEXT

information

You can select the language used to display the CD

TEXT information when you select a CD TEXT disc

with multi-language information.

Once you select the language, the display shows the

information in the selected language until you turn off

the player. If the player cannot read the language

memorised in a CD TEXT disc, “(other lang.)” appears.

1 Press INPUT in stop mode.

“Select lang.” flashes.

2 Push the JOG dial.

The current operating language flashes.

3 Turn the JOG dial until the language you want

appears in the display.

4 Push the JOG dial to select the language.

“Reading Text” appears momentarily, then the

display shows the information in the selected

language.

To check the current language

1 Press INPUT while playing a CD TEXT disc.

“Show lang.” flashes.

2 Push the JOG dial.

The current language appears momentarily.

You can also check the current language while selecting a CD

TEXT disc without multi-language information.

Note

If you select a CD TEXT disc which does not contain the

information of the selected language, the display shows the

information in another language according to the disc’s

priority.

Press TIME/TEXT.

ALL DISCS

CD TEXT

CD1

DISC

SONYHITS

ALL

Select lang.

DISCS

MULTI CD TEXT

CD1

21

ALL

English

DISCS

MULTI CD TEXT

CD1

21

Note

If the disc title and track title have more than 13 characters,

only the first 13 characters appear in the display.

Playing CDs

16

EN

Each time you press ≠/±, the characters

appear in the following order.

A B C D E F G H I J K L M N O P Q R S T U V W X

Y Z 0 1 2 3 4 5 6 7 8 9

If “NOT FOUND” appears in the display while

inputting the first character with the ≠/±

buttons, no disc has been labeled using the input

character.

Notes

• When searching for input characters, blanks and

symbols before the first character in the Disc Memo are

ignored.

• When searching for input characters, upper and lower

cases cannot be differentiated.

3 Turn the JOG dial to find the desired disc.

As you turn the JOG dial, the Disc Memos starting

with the input character appear in the display.

4 Push the JOG dial to select the disc.

In Program Play mode, the disc will be added to

the end of the program.

To cancel Memo Search

Press MEMO SEARCH again.

If there are no more Disc Memos starting with the

input character in Step 3

The input character search changes to the next one in

alphabetical order when you turn the JOG dial.

Input character

Locating a disc on the player

Turn the JOG dial until the desired disc number or

Disc Memo (see page 29) appears in the display. Push

the JOG dial to start play.

Locating a disc searching for a specific Disc

Memo (Memo Search)

You can search for and locate a desired disc by

inputting the first character used in the Disc Memo (see

page 29).

1 Press MEMO SEARCH.

“MEMO SEARCH” appears in the display.

2 Press ≠/± repeatedly to input the first

character.

JOG

≠/±

MEMO SEARCH

Locating a Specific Disc

ALL DISCS

CD1

S

SONYHITS

Playing CDsGetting Started

Playing CDs

17

EN

Locating a disc directly observing the

remote’s display

1 Move the cursor (”) to the desired disc by using

the Easy scroll key.

2 Press the Easy scroll key or ·.

If the player has no disc in the slot you selected,

“NO DISC!!!” appears.

Notes

• The Shuffle or Program Play mode (pages 20 and 21) will be

canceled when you locate a disc by observing the remote’s

display.

• If the MEGA CONTROL button, GROUP 1 – 8 buttons, or

the HIT LIST button is lit, you cannot locate a disc by

observing the remote’s display.

DISC

·

Number

buttons

ENTER

MEMO SCAN

Easy scroll

key

Locating a disc scanning each Disc Memo

(Memo Scan) Z

You can locate a desired disc quickly by scanning the

Disc Memos (see page 29) in the display .

Note that you cannot use this function in the ALL

DISCS Shuffle Play mode.

1 Press MEMO SCAN.

“MEMO SCAN” appears in the display, and the

Disc Memos scroll in the display.

2 Press · when the Disc Memo of the desired disc

appears.

The disc is set to the playing position, and the

player starts playing.

In Program Play mode, the disc will be added to

the end of the program if you press ENTER instead

of ·.

Note

If “NO ENTRY” appears in the display, no disc has been

labeled with the Disc Memo. Try the Memo Scan function

again after labeling the discs.

CONTINUE

PROGRAM

MEMO SCAN

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

DISC

SKIP

SHUFFLE

REPEAT

TIME/TEXT

GROUP

ENTER DEL

CLEAR

DISC SKIP

CHECK

NO DELAY

SPACE X-FADE

CAPS HIT LIST

DISC HIGH-LIGHT

3

DEF MEMO INPUT

6

MNO

9

WXY

2

ABC&!?

5

JKL

8

TUV

10/0

10

QZ

1

4

GHI

7

PRS

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

05:* DISC-5*

06:* DISC-6*

07:* DISC-7*

08:* DISC-8*

CD1

MENU

Locating a disc directly using the remote

1 Press DISC.

2 Press the number button of the disc.

Example: To enter number 35

Press 3, then 5.

3 Press ENTER to start play.

Playing CDs

18

EN

Locating a Specific Track or a

Point in a Track

You can quickly locate any track while playing a disc

using the ≠/± (AMS: Automatic Music Sensor)

buttons or by using the remote. You can also locate a

specific point in a track while playing a disc.

≠/±

Specifying the Next Disc to

Play

You can specify the next disc to play while playing a

disc in Continuous or 1 DISC Shuffle Play mode.

While playing a disc, turn the JOG dial. “NEXT DISC”

appears in the display and the disc number or Disc

Memo (see page 29) changes as you turn the JOG dial.

When the desired disc number or Disc Memo appears

in the display, stop turning the JOG dial.

After the current disc is played, the next disc you have

specified starts playing.

If you want to skip to the next disc right away, push

the JOG dial while playing the current disc.

To cancel the disc you have specified

Press CONTINUE twice.

Next disc number or

the Disc Memo

ALL DISCS

CD1

NEXT DISC

38

*DISC-38*

Locating a disc using the Disc Memo data

on the remote

You can search for and locate a desired disc by using

the Disc Memo data on the remote.

Before following the procedure below, be sure to load

the Disc Memo data into the remote’s memory (see

page 7).

1 Press MENU.

2 Move the cursor (”) to “Memo search” by using

the Easy scroll key, then press the Easy scroll key.

3 Push the Easy scroll key up or down until the first

character in the Disc Memo of the CD you want

appears.

Each time you push the Easy scroll key up or

down, the characters appear in the following

order.

A B C D E F G H I J K L M N O P Q R S T U V W X

Y Z 0 1 2 3 4 5 6 7 8 9

4 Press the Easy scroll key to input the character you

want.

The display shows the Disc Memos starting with

the input character. The second CD player’s disc

numbers are displayed in reverse contrast.

If “not found” appears after inputting the first

character, no disc has been labeled using the input

character.

5 Move the cursor to the disc number you want to

play, then press the Easy scroll key.

earch let ter

A

S

CD1

13:Hi techBlues

-end-

06:Hello

CD1

Playing CDsGetting Started

Playing CDs

19

EN

TRACK

Locating a specific track or a point in a

track observing the remote’s display

1 During stop mode, press TRACK.

2 Move the cursor (”) to a desired track by using the

Easy scroll key.

3 Press the Easy scroll key or ·.

Note

When you select a CD TEXT disc, track titles appear in Step 2

instead of the track numbers.

Number

buttons

0/)

>10

Easy scroll

key

=/+

Press

± repeatedly until you find the

track

≠ repeatedly until you find the

track

The number button of the track on the

remote. When you directly locate a

track numbered over 10, press >10

first, then the corresponding number

buttons.

0 (backward)/) (forward) on the

remote and hold down until you find

the point

0 (backward)/) (forward) on the

remote and hold down until you find

the point during pause. You will not

hear the sound during the operation.

Disc123

* DISC-123*

2 . ( TRACK2 )

1 . ( TRACK1 )

CD1

·

CONTINUE

PROGRAM

MEMO SCAN

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

DISC

SKIP

SHUFFLE

REPEAT

TIME/TEXT

GROUP

ENTER DEL

CLEAR

DISC SKIP

CHECK

NO DELAY

SPACE X-FADE

CAPS HIT LIST

DISC HIGH-LIGHT

3

DEF MEMO INPUT

6

MNO

9

WXY

2

ABC&!?

5

JKL

8

TUV

10/0

10

QZ

1

4

GHI

7

PRS

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

3 . (TRACK3 )

4 . ( TRACK4 )

6 . ( TRACK6 )

5 . ( TRACK5 )

CD1

Locating a specific track or a point in a

track

To locate

the next or

succeeding tracks

the current or

preceding tracks

a specific track

directly Z

a point in a track

while monitoring the

sound Z

a point in a track

quickly by observing

the display Z

Note

If “– OVER –” appears in the display, the disc has reached the

end while you were pressing ). Press ≠ or 0 to go

back.

Playing CDs

20

EN

Playing in Random Order

(Shuffle Play)

You can have the player “shuffle” the tracks and play

in random order. The player shuffles all the tracks on

all discs or on the disc you specify.

SHUFFLE

DISC

Number

buttons

JOG

·

ENTER

Playing Repeatedly

You can play discs or tracks repeatedly in any play

mode.

Press REPEAT while playing a disc.

“REPEAT” appears in the display. The player repeats

the discs/tracks as follows:

When the disc is played in

ALL DISCS Continuous Play

(page 12)

1␣ DISC Continuous Play

(page 12)

ALL DISCS Shuffle Play

(page 21)

1␣ DISC Shuffle Play

(page 21)

Program Play (page 21)

To cancel Repeat Play

Press REPEAT twice.

Repeating the current track

You can repeat the current track.

While the track you want is being played, press

REPEAT repeatedly until “REPEAT 1” appears in the

display.

To cancel Repeat 1

Press REPEAT.

The player repeats

All tracks on all discs

All tracks on the current disc

All tracks on all discs in

random order

All tracks on the current disc

in random order

The same program

REPEAT

CONTINUE

PROGRAM

MEMO SCAN

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

DISC

SKIP

SHUFFLE

REPEAT

TIME/TEXT

GROUP

ENTER DEL

CLEAR

DISC SKIP

CHECK

NO DELAY

SPACE X-FADE

CAPS HIT LIST

DISC HIGH-LIGHT

3

DEF MEMO INPUT

6

MNO

9

WXY

2

ABC&!?

5

JKL

8

TUV

10/0

10

QZ

1

4

GHI

7

PRS

MENU

PUSH ENTER

TRACK

PLAYER SELECT

BACK

La page charge ...

Sony CDP-CX260 Manuel utilisateur

Ce manuel convient également à

Sony CDP-CX260 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents