Yamaha HTR-5490 Manuel utilisateur

Catégorie
Récepteurs AV
Taper
Manuel utilisateur
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia
V795350
OWNER’S MANUAL
HTR-5490
U
AV Receiver
IMPORTANT
Please record the serial number of this unit in the
space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
0100HTR5490(U)-cv1/4 01.7.18, 9:33 AM1
I CAUTION
SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6 Attachments – Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lighting – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
0101HTR5490_Cau_EN(U) 01.7.6, 6:11 PM2
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
CAUTION II
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one
of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 81020)
GROUNDING CONDUCTORS
(NEC SECTION 81021)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers only)
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
20 Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check – Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is in
proper operating condition.
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection
to grounding electrodes, and requirements for the
grounding electrode.
0101HTR5490_Cau_EN(U) 01.7.6, 6:11 PM3
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place with at least 30 cm on the top, and 20 cm on
the right and left, and at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a
room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal
injury.
5 On the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Buring objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may
cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
III CAUTION
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than
specified is dangerous and may cause fire,
damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any
damage resulting from use of this unit with a
voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an
electrical storm.
14 Take care of this unit so that no foreign objects
and/or liquid drops inside this unit.
15 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
16 When not planning to use this unit for long
periods of time (i.e. vacation), disconnect the AC
power plug from the wall outlet.
17 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding
that this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
19 VOLTAGE SELECTOR (China model only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage
BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
0101HTR5490_Cau_EN(U) 01.7.6, 6:11 PM4
1
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
CONTENTS
INTRODUCTION
INTRODUCTION
CONTENTS ....................................................... 1
FEATURES ........................................................ 2
GETTING STARTED ....................................... 3
Checking the Package Contents ............................... 3
Installing Batteries in the Remote Control ............... 3
CONTROLS AND FUNCTIONS .................... 4
Front Panel ............................................................... 4
Remote Control ........................................................ 6
Using the Remote Control ........................................ 7
Front Panel Display .................................................. 8
Rear Panel ................................................................ 9
PREPARATION
SPEAKER SETUP .......................................... 10
Speakers to Be Used ............................................... 10
Speaker Placement ................................................. 10
Connecting the Speakers ........................................ 11
CONNECTIONS ............................................. 14
Before Connecting Components ............................ 14
Connecting Video Components .............................. 14
Connecting Audio Components ............................. 16
Connecting to a Subwoofer .................................... 18
Connecting an External Decoder ............................ 18
Connecting the Power Supply Cords ...................... 19
Turning on the Power ............................................. 20
ON-SCREEN DISPLAY (OSD) ..................... 21
OSD Modes ............................................................ 21
Selecting the OSD Mode ........................................ 21
SPEAKER MODE SETTINGS ..................... 22
Summary of SPEAKER SET Items 1A through 1F ...
22
ADJUSTING THE SPEAKER OUTPUT
LEVELS ....................................................... 23
Before You Begin ................................................... 23
Using the Test Tone (TEST DOLBY SUR.) .......... 23
BASIC OPERATION
BASIC PLAYBACK ........................................ 25
Input Modes and Indications .................................. 27
Selecting a Sound Field Program ........................... 28
Selecting PRO LOGIC or Neo: 6 ....................... 29
DIGITAL SOUND FIELD PROCESSING
(DSP) ............................................................ 31
Understanding Sound Fields .................................. 31
Hi-Fi DSP Programs............................................... 31
CINEMA-DSP ................................................. 32
Sound Design of CINEMA-DSP ............................ 32
CINEMA-DSP Programs ....................................... 34
TUNING ........................................................... 36
Connecting the Antennas ........................................ 36
Automatic and Manual Tuning ............................... 37
Presetting Stations .................................................. 38
Tuning in to a Preset Station .................................. 40
Exchanging Preset Stations .................................... 40
BASIC RECORDING ..................................... 41
ADVANCED OPERATION
REMOTE CONTROL FEATURES .............. 42
Control Area ........................................................... 42
Setting the Manufacturer Code .............................. 43
Programming a New Remote Control Function
(Learn Feature) ................................................... 44
Changing the Source Name in the Display Window ..
45
One Button Clear .................................................... 45
Clearing Learned Functions, Renamed Source
Names, and Setup Manufacturer Codes ............. 46
Each Component Control Area .............................. 47
SET MENU ...................................................... 52
Adjusting the Items on the SET MENU................. 52
1 SPEAKER SET (speaker mode settings) ........... 53
2 LOW FRQ TEST ............................................... 56
3 L/R BALANCE (balance of the left and right main
speakers)............................................................. 57
4 HP TONE CTRL (headphone tone control) ....... 57
5 CENTER GEQ (center graphic equalizer) ......... 57
6 INPUT RENAME .............................................. 58
7 I/O ASSIGNMENT ............................................ 58
8 INPUT MODE (initial input mode) ................... 59
9 PARAM. INI (parameter initialization) ............. 60
10 LFE LEVEL ..................................................... 60
11 DYNAMIC RANGE ......................................... 61
12 SP DELAY TIME ............................................. 61
13 DISPLAY SET .................................................. 62
14 MEMORY GUARD ......................................... 62
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS .................................................. 63
SLEEP TIMER ................................................ 64
Setting the Sleep Timer .......................................... 64
Canceling the Sleep Timer ..................................... 64
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM PARAMETER
EDITING ..................................................... 65
What is a sound field? ............................................ 65
Sound Field Program Parameters ........................... 65
Changing Parameter Settings ................................. 66
Resetting a Parameter to the Factory-set Value ...... 66
DIGITAL SOUND FIELD PARAMETER
DESCRIPTIONS ......................................... 67
TROUBLESHOOTING .................................. 71
GLOSSARY ..................................................... 76
SPECIFICATIONS ......................................... 78
0102HTR5490_1-9_EN(UA) 01.7.6, 6:42 PM1
2
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are
trademarks of Digital Theater System, Inc.
FEATURES
Built-in 6-Channel Power Amplifier
Minimum RMS Output Power
(0.04% THD, 20 Hz – 20 kHz, 8)
Main: 80 W + 80 W
Center: 80 W
Rear: 80 W + 80 W
Rear center: 80 W
Multi-Mode Digital Sound Field
Processing
Dolby Pro Logic/Dolby Pro Logic Decoder
Dolby Digital/Dolby Digital Matrix 6.1 Decoder
DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS
Neo: 6 Decoder
CINEMA DSP: Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital
or DTS
Virtual CINEMA DSP
SILENT CINEMA DSP
Sophisticated AM/FM Tuner
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset
Editing)
Other Features
96-kHz/24-bit D/A Converter
“SET MENU” which Provides You with 14 Items
for Optimizing This Unit for Your Audio/Video
System
Test Tone Generator for Easier Speaker Balance
Adjustment
6-Channel External Decoder Input for Other
Future Formats
BASS EXTENSION Button for Reinforcing
Bass Response
On Screen Display Function Helpful in
Controlling This Unit
S Video Signal Input/Output Capability
Component Video Input/Output Capability
Optical and Coaxial Digital Audio Signal Jacks
Sleep Timer
Remote Control with Preset Manufacturer Codes
and “Learning” Capability
PROCESSOR DIRECT for no alteration of the
original signal
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this
manual.
0102HTR5490_1-9_EN(UA) 01.7.9, 4:50 PM2
3
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
1
2
3
PHONO
POWER SLEEP
CLEAR
LEARN
STANDBY
TRANSMIT
RE–NAME
6CH INPUT
SYSTEM
V
-
AUX
A
D
-
TV/LD
POWER
REC
DISC SKIP
SET MENU
TV INPUT
A/B/C/D/E
AUDIO
VOL
LEVEL
MENU
STEREO
HALL
ENTER-
TAINMENT
TV
SPORTS
MONO
MOVIE
SELECT
6.1/ES
0
+
10
MOVIE
THEATER 1
MOVIE
THEATER 2
/DTS
SUR.
TEST
ON SCREEN
EFFECT
CHP/INDEX
TV VOL
RETURN
DISPLAY
PRESET PRESET
TV MUTE
TV VOL
SELECT
CHURCH
CHCH
JAZZ CLUB
ROCK
CONCERT
TITLE
MUTE
POWER
AMP
AVTV
VCR2/DVRVCR 1 DVD
SELECT
CBL/SAT MD/TAPE CD-R
TUNER CD
+
+
+
3421
5
910
11 12
67 8
Installing Batteries in the Remote
Control
Insert the batteries in the correct direction by aligning the
+ and marks on the batteries with the polarity markings
(+ and ) inside the battery compartment.
1 Press the part and slide the battery
compartment cover off.
2 Insert four supplied batteries (AAA, R03, UM-
4) according to the polarity markings on the
inside of the battery compartment.
3 Slide the cover back until it snaps into place.
Notes on batteries
Change the batteries periodically.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
Changing batteries
As the batteries lose power, the operating range of the
remote control decreases and the indicator does not flash
or its light becomes dim. When you notice any of these
conditions, change all of the batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
Note
If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
Connection GuideAM loop antenna
(Australia model)
Indoor FM antenna
(U.S.A., Canada and
China models)
Batteries (4)
(AAA, R03, UM-4)
Remote control
GETTING STARTED
Checking the Package Contents
Check your package to make sure it has the following items.
CENTER
SUB
WOOFER
S VIDEO
MONITOR OUT
VIDEO
DIGITAL OUTPUT
DIGITAL INPUT
6CH INPUT
GND
AUDIO AUDIO VIDEO
SPEAKERS
TUNER
75 UNBAL.
AM
ANT
GND
FM
ANT
COMPONENT VIDEO
S VIDEO
DVD
D-TV
/LD
CBL
/SAT
VIDEO
P
R
/ C
R
DVD
MONITOR
OUT
D-TV / LD
MAIN
REAR
CENTER
CENTER
REAR
P
B
/ C
B
Y
R
R
L
L
R
L
R
L
OPTICAL
MD
/
TAPE
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
CD-R
MD/TAPE
CD-R
DVD
D-TV
CD
CD
PHONO
IN
OUT
OUT
VCR 2
/DVR
VCR 1
IN
MAIN
SURROUND
/LD
CD
CBL
/SAT
(SURROUND)
COAXIAL
+
+
+
+
A
B
SUB
WOOFER
LR
AUDIO OUT S VIDEO
OUT
VIDEO
OUT
OPTICAL
COMPONENT
VIDEO OUT
AUDIO
OUT
S VIDEO IN VIDEO IN
S VIDEO
OUT
VIDEO
OUT
OPTICAL
OUT
O
COMPONENT
VIDEO IN
COMPONENT
VIDEO OUT
RIGHT LEFT
RIGHT
LEFT
L R
S
V
S
V
DVD Player Main Speaker
TV Subwoofer Center Speaker Rear Center
Speaker
Rear Speaker
CONNECTION
GUIDE
This connection guide shows the basic way to connect this unit
to a DVD player to enjoy 5.1 channel digital sources.
Carefully connect the speakers with
this unit not to cause short circuits.
Tightly twist the exposed wires of
the cable together to prevent short
circuits.
Connection with a DVD player
L
R
V
S
O
Analog audio signal
Optical digital signal
S video signal
Video signal
Signal flow
V795390
0102HTR5490_1-9_EN(UA) 01.7.6, 6:11 PM3
4
BASS
VOLUMEINPUT
INPUT M0DE
VIDEO AUXSILENT
PROGRAM
STEREO
SPEAKERS
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET
/
TUNING
PHONES
EFFECT
A/B/C/D/E
S VIDEO
MEMORY
FM/AM
EDIT
PRESET
/TUNING
MAN'L/AUTO FM AUTO/MAN'L MONO
TUNING
MODE
VIDEO AUDIO OPTICALLR
TUNER
STANDBY
/
ON
NATURAL SOUND AV RECEIVER
DSP
6CH INPUT
+
TREBLE
+
AB
DIGITAL
123 4567
8
90 q
w
e
r
t
y
s
a
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
FM/AM
i
o
pu
CONTROLS AND FUNCTIONS
Front Panel
1 STANDBY/ON
Turns on and sets this unit in the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Standby mode
In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this
unit (see page 8).
4 INPUT MODE
Sets the priority for the types of input signals (AUTO,
DTS, ANALOG) to receive when one component is
connected to two or more input jacks of this unit (see
page 27). Priority cannot be set when 6CH INPUT is
selected as the input source.
5 INPUT l / h
Selects the input source you want to listen to or watch.
6 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
7 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT l / h (or
the input selector buttons on the remote control).
8 SPEAKERS A/B
Turn on or off the set of main speakers connected to the A
and/or B terminals on the rear panel at each time its
corresponding button is pressed.
9 BASS EXTENSION
Turns on or off the BASS EXTENSION function at each
time the button is pressed, this feature boosts the bass
frequency of the left and right main channels by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
However, this boost may not be noticeable if 1B MAIN
SP on the SET MENU is set to SMALL and 1E LFE/
BASS OUT is set to SWFR.
0 PROCESSOR DIRECT
Turns on or off the PROCESSOR DIRECT function at
each time the button is pressed. When this is on, BASS,
TREBLE, and BASS EXTENSION are bypassed,
eliminating any alteration of the original signal.
0102HTR5490_1-9_EN(UA) 01.7.6, 6:11 PM4
5
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
D
I
G
I
T
A
L
To open, press gently on the lower part of the panel.
q STEREO/EFFECT
Switches the normal stereo or DSP effect reproduction.
When STEREO is selected, 2-channel input signals are
directed to the main left and right speakers without effect
sounds. All Dolby Digital and DTS audio signals except
for the LFE channel are mixed down to the main left and
right speakers.
w A/B/C/D/E
Selects one of the 5 preset station groups (A to E).
e PROGRAM l / h
Selects the DSP program (see page 28).
r PRESET/TUNING l / h
Selects preset station number 1 to 8 when the colon (:)
appears next to the band indication on the front panel
display, and selects the tuning frequency when the colon
(:) does not appear.
t PHONES jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.
y VIDEO AUX jacks
Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.
u PRESET/TUNING EDIT
Switches the function of PRESET/TUNING l / h (the
colon (:) turns on or off) between selecting a preset
station number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.
i FM/AM
Switches the reception band between FM and AM.
o MEMORY (MANL/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
p TUNING MODE (AUTO/MANL MONO)
Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the AUTO indicator lights up on the front panel
display. To select the manual tuning mode, press this
button so that the AUTO indicator does not light up.
a BASS
Adjusts the low-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.
s TREBLE
Adjusts the high-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.
Note
If you increase or decrease the high-frequency or the low-
frequency sound to an extreme level, the tonal quality from the
center and rear speakers may not match that of the left and
right main speakers.
Opening and closing the front
panel door
When you are not operating the controls behind the front
panel door, close the door.
0102HTR5490_1-9_EN(UA) 01.7.6, 6:11 PM5
6
CONTROLS AND FUNCTIONS
PHONO
POWER SLEEP
CLEAR
LEARN
STANDBY
TRANSMIT
RENAME
6CH INPUT
SYSTEM
V
-
AUX
A
D
-
TV/LD
POWER
REC
DISC SKIP
SET MENU
TV INPUT
A/B/C/D/E
AUDIO
VOL
LEVEL
MENU
STEREO
HALL
ENTER-
TAINMENT
TV
SPORTS
MONO
MOVIE
SELECT
6.1/ES
0 +10
MOVIE
THEATER 1
MOVIE
THEATER 2
/DTS
SUR.
TEST
ON SCREEN
EFFECT
CHP/INDEX
TV VOL
RETURN
DISPLAY
PRESET PRESET
TV MUTE
TV VOL
SELECT
CHURCH
CHCH
JAZZ CLUB
ROCK
CONCERT
TITLE
MUTE
POWER
AMP
AVTV
VCR2/DVRVCR 1 DVD
SELECT
CBL/SAT MD/TAPE CD-R
TUNER CD
+
+
+
3421
5
910
11 12
67 8
r
t
y
u
i
o
s
d
f
g
h
a
p
q
w
0
e
2
3
4
1
5
7
8
9
6
Remote Control
This section describes the controls and their functions of
the remote control. Make sure that the AMP mode is
selected before starting operation. See REMOTE
CONTROL FEATURES on pages 42 to 51 for operating
other components with the remote control.
y
Words and symbols in yellow are to operate this unit.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 TRANSMIT indicator
Flashes while the remote control is sending signals.
3 STANDBY
Sets this unit in the standby mode.
4 SYSTEM POWER
Turns on the power of this unit.
5 Å
Switches the control area for the extra component that is
not connected to this unit without changing the input.
6 Input selector buttons
Select the input source and change the control area.
7 Display window
Shows the selected source component that you are
controlling.
8 TV POWER
Turns on and off the power of the TV.
9 Operation Section
Provides functions such as play, stop, skip, etc. for
operating your other components.
0 LEVEL
Selects the effect speaker channel to be adjusted and sets
the level.
q Multi control section
Functions vary depending on your components that are
set up with the manufacturer code.
w TEST
Outputs the test tone to adjust the speaker levels.
e DSP program/Numeric buttons
Select DSP programs for the AMP position or numbers
for the other component positions. (Press a button
repeatedly to select a DSP program within that group.)
r RE-NAME
Used for changing the input source name in the display
window (see page 45).
t CLEAR
Used for clearing functions acquired when using the learn
and rename features, and set manufacturer codes (see
page 46).
y LEARN
Used for setting up the manufacturer code or for
programming the functions of other remote controls (see
page 44).
u SLEEP
Sets the sleep timer.
i 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
0102HTR5490_1-9_EN(UA) 01.7.6, 6:11 PM6
7
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
BASS
VOLUMEINPUT
INPUT M0DE
VIDEO AUX
SILENT
PROGRAM
STEREO
SPEAKERS
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET
/
TUNING
PHONES
EFFECT
A/B/C/D/E
S VIDEO
MEMORY
FM/AM
EDIT
PRESET
/TUNING
MAN'L/AUTO FM AUTO/MAN'L MONO
TUNING
MODE
VIDEO AUDIO OPTICALLR
TUNER
STANDBY
/
ON
NATURAL SOUND AV RECEIVER
DSP
6CH INPUT
+
TREBLE
+
AB
DIGITAL
30° 30°
Approximately 6 m (20 feet)
o SELECT k/n
Selects the another component to control independently
from the input that has been selected by pressing an input
selector button.
p AV POWER
Turns on and off the power of the component selected by
the input selector button.
a AMP
Selects AMP or other component selected by the input
selector button.
s VOL +/
Increases or decreases the volume level.
d MUTE
Mutes the sound. The MUTE indicator turns on when the
MUTE function is on. Press again to restore the audio
output to the previous volume level.
f SET MENU
Selects the SET MENU mode.
g ON SCREEN
Displays the input or operation status.
h STEREO/EFFECT
Switches the normal stereo or DSP effect reproduction.
When STEREO is selected, 2-channel input signals are
directed to the main left and right speakers without effect
sounds. All Dolby Digital and DTS audio signals except
for the LFE channel are also directed to the main left and
right speakers.
Using the Remote Control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity or temperature such as near a heater,
stove or bath;
dusty places; or
in places subject to extremely low temperatures.
0102HTR5490_1-9_EN(UA) 01.7.6, 6:11 PM7
8
CONTROLS AND FUNCTIONS
RL
LCR
RC RR
LFE
VIRTUAL
DTS
Neo
MOVIE THEATER
ENTERTAINMENT12
:6
DOLBY DIGITAL
PRO
LOGIC
VCR DVD TUNER CD
PHONO
CD RV AUX
DSP
MATRIX
DISCRETE
PCM
1
SILENT
SP
DIGITAL
VCR2/DVR
CBL
/
SAT
MD
/
TAPE
TV
/
LD
STEREO
TUNED
MEMORY
P. DIRECT
BASS
MUTE VOLUME
SLEEP
AUTO
D
6.1
/
ES
PRO LOGIC
/
AB
78 q wertyui
123456
90
1 Processor indicators
When any function of DSP, DTS, MTRIX DISCRETE,
VIRTUAL, g, 6.1/ES, and
PRO LOGIC
/
is
activated, its indicator lights up.
2 Input source indicator
Shows the current input source with underneath.
3 AUTO indicator
Shows that this unit is in the automatic tuning mode.
4 SLEEP indicator
Lights up while the sleep timer is on.
5 MUTE indicator
Flashes while the MUTE function is on.
6 VOLUME level indicator
Indicates the volume level.
7 v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
8 Headphones indicator
Lights up when headphones are connected.
9 SP A B indicator
Lights up according to which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.
0 SILENT indicator
Lights up when headphones are connected with the sound
effect (see SILENT CINEMA DSP on page 30).
q DSP program indicators
The name of the selected DSP program lights up when
the ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or V/DTS SURROUND DSP program is
selected.
w Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
e STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
r TUNED indicator
Lights up when this unit tunes in to a station.
t MEMORY indicator
Flashes to show a station can be stored.
y BASS indicator
Lights up while BASS EXTENSION is on.
u P. DIRECT
Lights up while PROCESSOR DIRECT is on.
i Input channel indicator
Indicates the channel components of input signals being
received.
Front Panel Display
0102HTR5490_1-9_EN(UA) 01.7.6, 6:11 PM8
9
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
AC OUTLETS
CENTER
SUB
WOOFER
S VIDEO
MONITOR OUT
VIDEO
DIGITAL OUTPUT
DIGITAL INPUT
6CH INPUT
GND
AUDIO AUDIO VIDEO
SPEAKERS
TUNER
75 UNBAL.
AM
ANT
GND
FM
ANT
COMPONENT VIDEO
S VIDEO
DVD
D-TV
/LD
CBL
/SAT
VIDEO
PR/ CR
DVD
MONITOR
OUT
D-TV / LD
MAIN
REAR
CENTER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
REAR
PB/ CB Y
R
R
L
L
R
L
R
L
OPTICAL
MD
/
TAPE
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
CD-R
MD/TAPE
CD-R
DVD
D-TV
CD
CD
PHONO
IN
OUT
OUT
VCR 2
/DVR
VCR 1
IN
MAIN
SURROUND
/LD
CD
CBL
/SAT
(SURROUND)
COAXIAL
+
+
+
+
MAIN A OR B:
A+B:
CENTER
4MIN. /SPEAKER
8MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
8MIN. /SPEAKER
16MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
REAR
REAR CENTER
:
:
:
MAIN A OR B:
A+B:
CENTER
REAR
REAR CENTER
:
:
:
A
B
SUB
WOOFER
OUTPUT
1
7
8 0 q9
2
3
4
5
6
*1
(U.S.A. model)
1 DIGITAL OUTPUT jacks
2 Audio component jacks
See pages 16 and 17 for connection information.
3 Video component jacks
See pages 14 and 15 for connection information.
4 SUBWOOFER jacks
See page 18 for connection information.
5 AC power cord
Connect to a power outlet.
6 AC OUTLET(S)
Use these outlets to supply power to your other A/V
components (see page 19).
7 DIGITAL INPUT jacks
8 6CH INPUT jacks
See page 18 for connection information.
9 Antenna input terminals
See page 36 for connection information.
0 Speaker terminals
See pages 11 and 12 for connection information.
q IMPEDANCE SELECTOR switch
Use this switch to match the amplifier output to your
speaker impedance (see page 36). Set this unit in the
standby mode before you change the setting of this
switch.
< China model only >
FREQUENCY STEP switch
See page 36.
VOLTAGE SELECTOR
See page 19.
*1 As this terminal is used for an examination in the factory, do not
connect any equipment to this terminal.
Rear Panel
0102HTR5490_1-9_EN(UA) 01.7.9, 11:03 AM9
10
SPEAKER SETUP
Speakers to Be Used
This unit has been designed to provide the best sound-
field quality with a 6-speaker system, using left and right
main speakers, left and right rear speakers, and a center
and rear center speakers. If you use different brands of
speakers (with different tonal qualities) in your system,
the tone of a moving human voice and other types of
sound may not shift smoothly. We recommend that you
use speakers from the same manufacturer or speakers
with the same tonal quality.
The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). If
for some reason it is not practical to use a center speaker,
you can do without it. Best results, however, are obtained
with the full system.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use the
models of equivalent performance with the main
speakers.
Use of a subwoofer expands your
sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.
PREPARATION
Speaker Placement
Refer to the following diagram when you place the
speakers.
Main speakers
Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.
Note
If the center speaker is not used, the center channel sound will
be heard from the left and right main speakers. In this case,
1A CENTER SP on the SET MENU is set to NONE (see
page 53 for details).
Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (6 feet) above the
floor.
Rear center speaker
Place the rear center speaker in the center between the left
and right rear speakers at the same height from the floor
as the rear speakers.
Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.
CAUTION
Use magnetically shielded speakers. If this type of
speakers still creates the interference with a monitor,
place the speakers away from the monitor.
Main
speaker (L)
1.8 m (6 feet)
Rear speaker (L)
Rear center
speaker
Rear speaker (R)
Subwoofer
Main speaker (R)Center speaker
0103HTR5490_10-18_EN(UA) 01.7.6, 6:11 PM10
11
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
12
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), + (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
Use speakers with the specified impedance shown on the rear panel of this unit.
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage this unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approximately 10 mm (3/8) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
y
(U.S.A., Canada, Australia and China models only)
Banana plug connections are also possible. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.
10 mm (3/8)
MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
REAR CENTER SPEAKER terminals
A rear center speaker can be connected to these terminals.
Red: positive (+)
Black: negative ()
Banana plug
3
1
2
0103HTR5490_10-18_EN(UA) 01.7.6, 6:11 PM11
12
SPEAKER SETUP
AC OUTLETS
CENTER
SUB
WOOFER
S VIDEO
MONITOR OUT
VIDEO
DIGITAL OUTPUT
DIGITAL INPUT
6CH INPUT
GND
AUDIO AUDIO VIDEO
SPEAKERS
TUNER
75 UNBAL.
AM
ANT
GND
FM
ANT
COMPONENT VIDEO
S VIDEO
DVD
D-TV
/LD
CBL
/SAT
VIDEO
P
R
/ C
R
DVD
MONITOR
OUT
D-TV / LD
MAIN
REAR
CENTER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
REAR
P
B
/ C
B
Y
R
R
L
L
R
L
R
L
OPTICAL
MD
/
TAPE
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
CD-R
MD/TAPE
CD-R
DVD
D-TV
CD
CD
PHONO
IN
OUT
OUT
VCR 2
/DVR
VCR 1
IN
MAIN
SURROUND
/LD
CD
CBL
/SAT
(SURROUND)
COAXIAL
+
+
+
+
MAIN A OR B:
A+B:
CENTER
4MIN. /SPEAKER
8MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
8MIN. /SPEAKER
16MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
REAR
REAR CENTER
:
:
:
MAIN A OR B:
A+B:
CENTER
REAR
REAR CENTER
:
:
:
A
B
SUB
WOOFER
OUTPUT
1
4567
23
Subwoofer
system
Rear Center
speaker
Main B speaker
Center
speaker
(U.S.A. model)
Right
Rear speaker
SUBWOOFER jack
When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,
connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or
rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The
LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are
assigned to this jack.
Notes
Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level by using the
remote control of this unit (see ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS on page 63).
Depending on the settings of 1 SPEAKER SET and 10 LFE LEVEL on the SET MENU, some signals may not be output from
the SUBWOOFER jack.
Right Left
Main A speaker
Right Left
Left
1
2
3
4
5
7
6
The diagram above shows the speaker layout in the
listening room.
0103HTR5490_10-18_EN(UA) 01.7.6, 6:11 PM12
13
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
AC OUTLETS
SET BEFORE POWER ON
MAIN A OR B:
A+B:
CENTER
4MIN. /SPEAKER
8MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
8MIN. /SPEAKER
16MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
REAR CENTER
:
:
:
MAIN A OR B:
A+B:
CENTER
REAR
REAR CENTER
:
:
:
IMPEDANCE SELECTOR
REAR
8MIN. /SPEAKER
16MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
8MIN. /SPEAKER
MAIN A OR B:
A+B:
CENTER
REAR
REAR CENTER
:
:
:
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B:
A+B:
CENTER
4MIN. /SPEAKER
8MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
6MIN. /SPEAKER
REAR
REAR CENTER
:
:
:
Switch
position
Left
Right
Speaker
Main
Center
Rear
Center
Rear
Main
Center
Rear
Center
Rear
Impedance level
If you use one set of main speakers, the impedance of
each speaker must be 4 or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 8 or higher.
The impedance must be 6 or higher.
The impedance must be 6 or higher.
The impedance of each speaker must be 6 or higher.
If you use one set of main speakers, the impedance of
each speaker must be 8 or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16 or higher.
[Canada model only]
The impedance of each speaker must be 8 or higher.
The impedance must be 8 or higher.
The impedance must be 8 or higher.
The impedance of each speaker must be 8 or higher.
IMPEDANCE
SELECTOR
switch
(U.S.A. model)
IMPEDANCE SELECTOR switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
Select the left and right position according to the impedance of the speakers in your system. Be sure to move this switch
only when this unit is in the standby mode.
0103HTR5490_10-18_EN(UA) 01.7.6, 6:11 PM13
14
CONNECTIONS
Before Connecting Components
CAUTION
Never connect this unit and other components to mains power until all connections between components have been
completed.
Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, + to + and “–” to “–”. Some
components require different connection methods and have different jack names. Refer to the operation instructions
for each component to be connected to this unit.
When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling
system to all its products.
After you have completed all connections, check them again to make sure they are correct.
Connecting Video Components
About the video jacks
There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video
signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.
The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO
jacks are separated into luminance (Y) and color difference (P
B
/C
B
, P
R
/C
R
) video signals. The jacks are also separated
into three for each signal. The description of the component video jacks may be different depending on the component
(e.g. Y, C
B
, C
R
/Y, P
B
, P
R
/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.
If your video component has an S-video output or component video output, you can connect it to this unit. Connect the
S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks
on your video component to the COMPONENT VIDEO jacks.
y
Each type of video jack works independently. Signals input through the composite
video, S-video and component jacks are output through the corresponding composite
video, S-video, and component jacks, respectively.
You can designate the input for the COMPONENT VIDEO A and B jacks according
to your component by using 7 I/O ASSIGNMENT on the SET MENU (see pages
58 and 59 for details).
Notes
Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when
connecting to the COMPONENT VIDEO jacks.
When you are using the COMPONENT VIDEO jacks, check the details in the owners manual that came with the component being
connected.
VIDEO AUX jacks (on the front panel)
These jacks are used to connect any video input source
such as a game console and a camcorder to this unit.
S VIDEO VIDEO
L AUDIO R OPTICAL
VIDEO AUX
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
OPTICAL OUT
S VIDEO OUT
O
V
L
R
S
Game console or camcorder
VIDEO
COMPONENT VIDEO
S VIDEO VIDEO
P
R
/ C
R
P
B
/ C
B
Y
VIDEO jack
(composite)
COMPONENT
VIDEO jacks
S VIDEO
jack
0103HTR5490_10-18_EN(UA) 01.7.6, 6:11 PM14
15
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
CENTER
SUB
WOOFER
DIGITAL OUTPUT
DIGITAL INPUT
6CH INPUT
GND
AUDIO
TUNER
75 UNBAL.
AM
ANT
GND
FM
ANT
MAIN
MAIN
SUB
WOOFER
R
R
L
L
R
L
OPTICAL
MD
/
TAPE
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
CD-R
MD/TAPE
CD-R
CD
CD
PHONO
MAIN
SURROUND
CD
+
+
A
B
COAXIAL
CBL
/SAT
AUDIO VIDEO
COMPONENT VIDEO
S VIDEO
DVD
D-TV
/LD
CBL
/SAT
VIDEO
P
R
/ C
R
DVD
MONITOR
OUT
D-TV / LD
P
B
/ C
B
Y
R
L
IN
OUT
OUT
VCR 2
/DVR
VCR 1
IN
S VIDEO
MONITOR OUT
VIDEO
DVD
/LD
D-TV
L
R
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
INPUT
VIDEO
INPUT
S VIDEO
OUTPUT
AUDIO
OUTPUT
AUDIO
OUTPUT
AUDIO INPUT
AUDIO OUTPUT
COAXIAL
OUTPUT
OPTICAL
OUTPUT
RF
OUTPUT
OPTICAL
OUTPUT
VIDEO
OUTPUT
VIDEO
OUTPUT
AUDIO
OUTPUT
VIDEO
OUTPUT
RF
INPUT
VIDEO
OUTPUT
VIDEO
INPUT
O
O
COMPONENT
INPUT
COMPONENT
OUTPUT
COMPONENT
OUTPUT
L
R
C
C
*1
L
R
L
R
V
S
S
S VIDEO
INPUT
S
V
V
S
S
V
V
V
S
L
R
L
S
R
V
C
O
(U.S.A. model)
LD player
RF
demodulator
*1 If your LD player has an RF
OUTPUT jack, first connect it to
the RF INPUT on an RF
demodulator and then connect
the RF OUTPUT on an RF
demodulator to the COAXIAL
jack on this unit.
indicates S-video cables
indicates video cables
indicates coaxial cables
indicates optical cables
indicates right analog cables
indicates left analog cables
indicates signal direction
Video monitor
VCR 1 or VCR 2/
DVR (digital
video recorder)
Cable TV or
Satellite tuner
DVD player
TV/digital TV or
LD player
0103HTR5490_10-18_EN(UA) 01.7.6, 6:11 PM15
16
CONNECTIONS
Connecting Audio Components
Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. When you connect components to
both the COAXIAL and OPTICAL jacks, priority is given
to the input signals from the COAXIAL jack. All digital
input jacks are acceptable for 96-kHz sampling digital
signals (see page 27 for details).
y
You can designate the input for each digital jacks according to
your component by using 7 I/O ASSIGNMENT on the SET
MENU (see pages 58 and 59 for details).
Note
The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
Connecting a turntable
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an in-line boosting
transformer or MC-head amplifier when connecting to
these jacks.
y
Connect your turntable to the GND terminal to reduce noise in
the signal. However you may hear less noise without the
connection to the GND terminal for some record players.
Connecting a CD player
y
The COAXIAL CD and OPTICAL CD jacks are available for a
CD player which has coaxial or optical digital output jacks.
When you connect a CD player to both the COAXIAL CD and
OPTICAL CD jacks, priority is given to the input signals from
the COAXIAL CD jack.
Connecting an MD recorder, tape
deck or CD recorder
y
DIGITAL OUTPUT jacks and analog OUT(REC) are
independent. Only digital signals are output from DIGITAL
OUTPUT jacks and analog signals from OUT(REC) jacks.
When you connect your recording component to both the
analog and digital input and output jacks, the priority is given
to the digital signal.
Notes
When you connect a recording component to this unit, keep its
power on while using this unit. If the power is off, this unit may
distort the sound from other components.
When you record from a source component connected to this
unit while this unit is set in the standby mode, the recorded
sound may be distorted. To avoid this problem, turn on this
unit.
0103HTR5490_10-18_EN(UA) 01.7.6, 6:11 PM16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83

Yamaha HTR-5490 Manuel utilisateur

Catégorie
Récepteurs AV
Taper
Manuel utilisateur