Yamaha DGX-640 Le manuel du propriétaire

EN

Owner’s Manual

Keyboard Stand Assembly

For information on assembling the

keyboard stand, refer to the instructions

on page 10 of this manual.

Setting UpReferenceAppendix Quick Guide

Owner’s Manual

2

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING:

Do not place this product in a position where anyone could

walk on, trip over, or roll anything over power or connecting cords of any

kind. The use of an extension cord is not recommended! If you must use an

extension cord, the minimum wire size for a 25’ cord (or less) is 18 AWG.

NOTE: The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to update

existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound levels

that could cause permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level that is uncomfort-

able. If you experience any hearing loss or ringing in the ears, you

should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory

mounting fixtures that are either supplied with the product or as

optional accessories. Some of these items are designed to be dealer

assembled or installed. Please make sure that benches are stable and

any optional fixtures (where applicable) are well secured BEFORE

using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are

not covered by the manufacturer’s warranty, and are therefore the

owners responsibility. Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately five years. When replacement becomes necessary,

contact a qualified service representative to perform the replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of prod-

ucts that contain lead, batteries, plastics, etc. If your dealer is unable

to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

Owner’s Manual

3

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge

som den ar ansluten till vägguttaget, även om själva apparaten

har stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE

afbrudt, sålæenge netledningen siddr i en stikkontakt, som er t

endt — også selvom der or slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita

koko laitetta verkosta.

(standby)

The serial number of this product may be found on the bottom

of the unit. You should note this serial number in the space

provided below and retain this manual as a permanent record

of your purchase to aid identification in the event of theft.

Model No.

Serial No.

(bottom)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured makings identifying the

terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the ter-

minal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal

of the three pin plug.

* This applies only to products distributed by

Yamaha Music U.K. Ltd.

(2 wires)

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products

should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with

your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal

service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer

and ask for the correct method of disposal.

(weee_eu_en)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park,

Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Piano

Model Name : DGX-640

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception is

suspected.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(FCC DoC)

Owner’s Manual

4

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-

circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on it,

or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the specified adaptor (page 112) only. Using the wrong adaptor can result in

damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument

or attempt to disassemble or modify the internal components in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into any

openings. If any liquid such as water seeps into the instrument, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

instrument inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. Then have the device inspected

by Yamaha service personnel.

• The power cord or plug becomes frayed or damaged.

• It emits unusual smells or smoke.

• Some object has been dropped into the instrument.

• There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• Before moving the instrument, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When

you are not using the product for a long time, make sure to unplug the power cord

from the wall AC outlet.

• Use only the stand specified for the instrument. When attaching the stand or rack,

use the provided screws only. Failure to do so could cause damage to the internal

components or result in the instrument falling over.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and

gradually raise the volume controls while playing the instrument to set the desired

listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing loss.

If you experience any hearing loss or ringing in the ears, consult a physician.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Location

Connections

Handling caution

(7)-1 1/2

Owner’s Manual

5

Always turn the power off when the instrument is not in use.

Even when the [ ](Standby/On) switch is in the “Standby” position, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for

a long time, make sure you unplug the power cord from the wall AC outlet.

NOTICE

To avoid the possibility of damage to the product, data or other property, follow the notices below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio

may generate noise.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day)

to prevent the possibility of panel disfiguration or damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the instrument. If water is left, the

wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately with a soft cloth.

–

 Saving data

• Some data items (page 64) are automatically saved as backup data in the internal memory even if you turn the power off. Saved data may be lost due to

malfunction or incorrect operation. Save important data to a USB storage device/or other external device such as a computer (pages 93–94 and 101).

• To protect against data loss through media damage, we recommend that you save your important data onto two USB storage devices/or other external

device such as a computer.

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal

use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use

others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and

sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of

copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

 About functions/data bundled with the instrument

• Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.

• This device is capable of using various types/formats of music data by optimizing them to the proper format music data for use with the device in advance.

As a result, this device may not play them back precisely as their producers or composers originally intended.

 About this manual

• The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your

instrument.

• Windows is a registered trademark of Microsoft

®

Corporation in the United States and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

(7)-1 2/2

Owner’s Manual

6

Logos

GM System Level 1

“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-compatible

music data can be accurately played by any GM-compatible tone generator, regardless of manufacturer.

The GM mark is affixed to all software and hardware products that support GM System Level.

XGlite

As its name implies, “XGlite” is a simplified version of Yamaha’s high-quality XG tone generation for-

mat. Naturally, you can play back any XG song data using an XGlite tone generator. However, keep in

mind that some songs may play back differently compared to the original data, due to the reduced set of

control parameters and effects.

XF

The Yamaha XF format enhances the SMF (Standard MIDI File) standard with greater functionality and

open-ended expandability for the future. The instrument is capable of displaying lyrics when an XF file

containing lyric data is played.

STYLE FILE

The Style File Format is Yamaha’s original style file format which uses a unique conversion system to

provide high-quality automatic accompaniment based on a wide range of chord types.

Owner’s Manual

7

About this Owner’s Manual and Data List

This manual consists of four main sections: “Setting Up,” “Quick Guide,” “Reference,” and “Appendix.”

Also, a separate “Data List” is provided.

Owner’s Manual (this book)

Data List

Voice List, MIDI Data Format, etc.

MIDI Reference

The MIDI Reference section contains MIDI related information. The MIDI Reference is available for

downloading from the Yamaha Manual Library at: http://www.yamaha.co.jp/manual/

Included Accessories

The DGX-640 package includes the following items. Please check that you have them all.

•Music rest

• Accessory CD-ROM

• Owner’s manual (this book)

• Keyboard stand

• Footswitch

•AC Power Adaptor

* May not be included depending on your particular area.

Please check with your Yamaha dealer.

• Data List

• My Yamaha Product User Registration

* The PRODUCT ID on the sheet will be needed when

you fill out the User Registration form.

Setting Up

• • • • • • • • •

Please read this section first.

This section explains how to use the basic functions. Refer to this

section while playing the instrument.

Quick Guide

• • • • • • • • •

Reference

• • • • • • • • •

This section explains how to make detailed settings for the instru-

ment’s various functions.

Appendix

• • • • • • • • •

This section includes troubleshooting information and specifica-

tions.

Insert the music rest into

the slots as shown.

Music Rest

Owner’s Manual

8

Special Features

Performance assistant technology

Page 43

Play along with a song on the instrument’s keyboard and produce a perfect per-

formance every time ... even if you play wrong notes! All you have to do is play

on the keyboard—alternately on the left- and right-hand ranges of the keyboard,

for example—and you’ll sound like a pro as long as you play in time with the

music.

And if you can’t play with both hands, you can still play the melody simply by

tapping one key.

Play a Variety of Instrument Voices

Page 18

With the DGX-640, the instrument voice that sounds when you play the key-

board can be changed to violin, flute, harp, or any of an extensive range of

voices. You can change the mood of a song written for piano, for example, by

using violin to play it instead. Experience a whole new world of musical variety.

Play Along with Styles

Page 24

Want to play with full accompaniment? Try the auto-accompaniment Styles. The

accompaniment styles provide the equivalent of a full backing band covering

wide variety of styles from waltzes to 8-beat to euro-trance … and much more.

Select a style that matches the music you want to play, or experiment with new

styles to expand your musical horizons.

Easy Performance with Music Notation Display

Page 32

When you play back a song, the corresponding score will be shown on the dis-

play as the song plays. This is a great way to learn how to read music. If the song

contains lyric and chord data*, the lyrics and chords will also appear on the score

display.

* No lyrics or chords will appear on the display if the song you are using with the score display

function does not contain the appropriate lyric and chord data.

Graded Hammer Standard Keyboard

Thanks to our experience as the world’s leading manufacturer of acoustic pianos, we’ve developed a key-

board with action that’s virtually indistinguishable from the real thing. Just as on a traditional acoustic

piano, the keys of the lower notes have a heavier touch, while the higher ones are more responsive to

lighter playing. The keyboard’s sensitivity can even be adjusted to match your playing style. This Graded

Hammer technology also enables the DGX-640 to provide authentic touch in a lightweight instrument.

All you need is

one finger!

Owner’s Manual

9

Quick GuideReferenceAppendix Setting Up

Contents

About this Owner’s Manual and Data List ........................7

Included Accessories .......................................................7

Special Features ..............................................................8

Setting Up

Setting Up 10

Keyboard Stand Assembly.............................................10

Power Requirements......................................................13

Connecting Headphones (PHONES/OUTPUT Jack).....13

Connecting a Footswitch (SUSTAIN Jack).....................13

Connecting a Pedal Unit (PEDAL UNIT jack).................14

Connecting to a Computer (USB Terminal)....................15

Turning the Power On ....................................................15

Panel Controls and Terminals 16

Quick Guide

Try Playing a Variety of Instrument Voices 18

Select and Play a Voice—MAIN.....................................18

Play the Grand Piano Voice ...........................................19

Play Two Voices Simultaneously—DUAL ......................20

Play Different Voices with the Left and Right

Hands—SPLIT ...............................................................21

The Metronome 22

Start the Metronome ......................................................22

Adjusting the Metronome Tempo ...................................22

Setting the Time Signature.............................................23

Playing Styles 24

Select a Style Rhythm ....................................................24

Play Along with a Style...................................................25

Playing Songs 28

Select and Listen to a Song ...........................................28

Select and Play Songs on a USB Flash Memory...........30

Song Fast Forward, Fast Reverse, and Pause ..............31

Play the Demo Song ......................................................31

Displaying the Song Score.............................................32

Display the Lyrics ...........................................................33

Reference

Basic Operation 34

Select a Song For a Lesson 38

The Easy Way to Play Piano 43

Play Using the Music Database 53

Change a Song’s Style 54

Record Your Own Performance 56

Memorize Your Favorite Panel Settings 62

Backup and Initialization 64

Backup ...........................................................................64

Initialization ....................................................................64

Play with a Variety of Effects 65

Adding Harmony ............................................................65

Adding Reverb ...............................................................66

Adding Chorus ...............................................................66

Adding DSP ...................................................................67

Panel Sustain.................................................................68

Pitch Bend......................................................................68

Select an EQ Setting for the Best Sound.......................69

Handy Performance Features 70

Tap Start ........................................................................70

One Touch Setting .........................................................70

Setting the Click bell sound............................................70

Adjusting the Metronome Volume..................................71

Changing the Display Language....................................71

Voice Settings 72

Voice Editing ..................................................................72

Selecting a Dual Voice ...................................................73

Selecting a Split Voice ...................................................73

Pitch Controls (Transpose) ............................................74

Pitch Controls (Tuning) ..................................................74

Touch Response Sensitivity...........................................75

Style (Auto-accompaniment) Functions 76

Pattern Variation (Sections) ...........................................76

Changing the tempo of the Style....................................79

Adjusting the Style Volume ............................................79

Setting the Split Point.....................................................80

Play a Style with Chords but No Rhythm

(Stop Accompaniment) ..................................................80

AI Fingered ....................................................................81

Playing Styles Using the Entire Keyboard......................81

Looking Up Chords Using the Chord Dictionary ............82

Song Settings 83

Changing the tempo of the Song ...................................83

Song Volume .................................................................83

A-B Repeat ....................................................................84

Muting Independent Song Tracks ..................................84

Change the Melody Voice..............................................84

BGM Playback ...............................................................85

Random Song Playback ................................................85

The Functions 86

Selecting and Setting Functions ....................................86

Saving and Loading Data 90

Connecting a USB Flash Memory..................................90

Precautions when using the USB TO DEVICE terminal

..91

Using USB Storage Devices ..........................................91

Connecting to a Computer 97

Connecting a Personal Computer..................................97

Transferring Performance Data to and from a Computer

..98

Transferring Data Between the Computer and

Instrument ......................................................................99

Accessory CD-ROM Installation Guide 102

Important Notices about the CD-ROM .........................102

CD-ROM Contents.......................................................103

System Requirements..................................................104

Software Installation.....................................................104

Appendix

Troubleshooting 109

Messages 110

Specifications 112

Index 113

Owner’s Manual

10

Setting Up

Keyboard Stand Assembly

1

The parts shown in the “Assembly Parts” illustration will be used. Follow the assembly instructions and select

the parts as needed.

CAUTION

Read these cautions carefully before you assemble or use the keyboard stand.

These cautions are to promote safe use of the stand and to prevent injury and damage from occurring to you and others. By fol-

lowing these cautions carefully, your keyboard stand will provide you with safe and prolonged use.

• Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the

sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.

• Use the stand after assembly is complete. An uncompleted stand may overturn or the keyboard may drop.

• Always place the stand on a flat, stable surface. Placing the stand on uneven surfaces may cause it to become unstable or over-

turn, the keyboard to drop, or injury.

• Do not use the stand for anything other than its designed purpose. Placing other objects on the stand may result in the object

dropping or the stand overturning.

• Do not apply excessive force to the keyboard as it may cause the stand to overturn or the keyboard to drop.

• Make sure the stand is sturdy and safe, and all screws have been tight and firm before use. If not, the stand may overturn, the

keyboard may drop, or may result in injury to the user.

• To disassemble, reverse the assembly sequence given below.

Have a phillips-head (+) screwdriver of the appropriate size ready.

q Joint connectors

(4 pcs.)

w 6 x 70 mm

roundhead

screws (4 pcs.)

e 6 x 30 mm

roundhead

screws (4 pcs.)

r 5 x 16 mm

roundhead

screws (4 pcs.)

1

Assembly Parts

Back board

Side

boards

Stand

bases

Setting Up

Owner’s Manual

11

Setting Up

2 Attach the stand bases.

Insert the joint connectors q into the side boards as

shown. The joint connectors have been installed

properly if you can see the screw head on the con-

nector.

Attach the “L” (Left) and “R” (Right) stand bases

to the bottom of the side boards, using the screws

w. “L” (Left) and “R” (Right) are marked on the

upper surfaces of the stand bases. If you have trou-

ble fastening the screws, use a screwdriver to rotate

the joint connectors so that the connector holes are

aligned with the screw holes on the stand bases.

3 Attach the back board.

Attach the back board, using the screws e. Check

the back-to-front orientation for the side boards.

Make sure the non-colored surface is facing down.

2

q Joint

connectors

w 6 x 70 mm

roundhead screws

“L”

“R”

3

e 6 x 30 mm roundhead screws

• If you put the connectors in wrong direction and want to

take them out, tap around the holes on the boards.

• Be careful not to drop the back board or touch the

sharp metal fittings.

• If you have purchased an optional pedal unit, attach the

pedal unit before proceeding to the next step. Refer to the

instructions provided with your pedal unit.

NOTE

CAUTION

NOTE

Setting Up

Owner’s Manual

12

Setting Up

4 Put the keyboard on the stand.

Check the back-to-front orientation for stand, and

carefully place the keyboard on the side boards.

Slowly move the keyboard so that the holes on the

bottom of the keyboard are properly aligned with

the holes on the angle brackets.

5 Install the keyboard to the stand.

Fix the keyboard to the angle brackets, using the

screws

r.

4

At least

10 cm

At least

10 cm

Be sure to place your hands at

least 10 cm from either end of the

keyboard when positioning it.

5

r 5 x 16 mm

roundhead

screws

• Be careful not to drop the keyboard or to get your fin-

gers caught between the keyboard and the stand parts.

• Do not hold the keyboard in any position other than the

position shown in the illustration.

Post-assembly checklist

Once you’ve assembled the stand, check the follow-

ing points:

• Are there any parts left over?

 If so, read the assembly instructions again and

correct any errors you might have made.

• Is the instrument clear of doors and other movable

fixtures?

 If not, move the instrument to an appropriate

location.

• Does the instrument make a rattling noise when you

play it or move it?

 If so, properly tighten all screws.

• Also, if the keyboard makes a creaking noise or

seems unsteady when you play it, refer carefully to

the assembly instructions and diagrams and

retighten all screws.

CAUTION

Setting Up

Owner’s Manual

13

Setting Up

Be sure to do the following operations BEFORE turning on the power.

Power Requirements

1 Make sure that the [ ](Standby/On) switch of the

instrument is in the “Standby” position.

2 Connect the AC adaptor to the power supply jack.

3 Plug the AC adaptor into an AC outlet.

Make all necessary connections below BEFORE turning the power on.

Connecting Headphones (PHONES/OUTPUT Jack)

Any pair of stereo headphones with a 1/4" stereo

phone plug can be plugged in here for convenient

monitoring. The speakers are automatically shut off

when a plug is inserted into this jack.

The PHONES/OUTPUT jack also functions as an

external output. You can connect the PHONES/OUT-

PUT jack to a keyboard amplifier, stereo system,

mixer, tape recorder, or other line-level audio device

to send the instrument’s output signal to that device.

Connecting a Footswitch (SUSTAIN Jack)

The sustain function lets you produce a natural sustain

as you play by pressing a footswitch. Plug the sup-

plied footswitch into this jack and use it to switch sus-

tain on and off.

• Use the specified adaptor (page 112). The use of other

adaptors may result in irreparable damage to both the

adaptor and the instrument.

• Unplug the AC Power Adaptor when not using the

instrument, or during electrical storms.

WARNING

CAUTION

AC outlet

AC power

adaptor

3

2

• Avoid listening with the headphones at high volume for

long periods of time; doing so may not only result in ear

fatigue, it may be damaging to your hearing.

• To prevent damage to the speakers, set the volume of the

external devices at the minimum setting before connecting

them. Failure to observe these cautions may result in elec-

tric shock or equipment damage. Also, be sure to set the

volumes of all devices at their minimum levels and gradu-

ally raise the volume controls while playing the instrument

to set the desired listening level.

WARNING

CAUTION

• The sustain function does not affect split voices.

• Make sure that the footswitch plug is properly connected to

the SUSTAIN jack before turning on the power.

• Do not press the footswitch while turning the power on. Doing

this changes the recognized polarity of the footswitch, result-

ing in reversed footswitch operation.

NOTE

Setting Up

Owner’s Manual

14

Setting Up

Connecting a Pedal Unit (PEDAL UNIT jack)

This jack is for connecting an optional LP-7A pedal

unit. When connecting the pedal unit, make sure to

also assemble the unit on the supplied keyboard stand.

Keyboard

Stand

LP-7A (optional)

• Make sure that power is OFF when connecting or disconnect-

ing the pedal.

NOTE

Pedal Unit Functions

The optional pedal unit has three foot pedals that produce a range of expres-

sive effects similar to those produced by the pedals on an acoustic piano.

The pedal unit does not affect the split voice when the keyboard is in split

mode.

Damper (Right) Pedal

The damper pedal functions in the same way as a damper pedal on an

acoustic piano. When the damper pedal is pressed, notes sustain longer.

Releasing the pedal immediately stops (damps) any sustained notes.

A “half-pedal” effect lets you use the damper pedal to create partial sus-

tain effects, depending on how far down you press the pedal.

* When using both the Footswitch and pedal unit, the last effect applied takes

priority.

Sostenuto (Center) Pedal

If you play a note or chord on the keyboard and press the sostenuto

pedal while the note(s) are held, those notes will sustain as long as you

hold the pedal (as if the damper pedal had been pressed) but all subse-

quently played notes will not be sustained. This makes it possible to

sustain a chord, for example, while other notes are played “staccato.”

Soft (Left) Pedal

The soft pedal reduces the volume and slightly changes the timbre of

notes played while the pedal is pressed. The soft pedal will not affect

notes that are already playing when it is pressed.

When you press the damper

pedal here, the notes you play

before you release the pedal

have a longer sustain.

When you press the sostenuto

pedal here while holding the

note, the note will sustain as

long as you hold the pedal.

Setting Up

Owner’s Manual

15

Setting Up

Connecting to a Computer (USB Terminal)

Connect the instrument’s USB terminal to the USB

terminal of a computer, and you can transfer perfor-

mance data and song files between the two (page 97).

Turning the Power On

The [ ](Standby/On) switch turns the power to the

instrument on ( ) or standby ( ).

Turn down the volume by turning the [MASTER

VOLUME] control to the left and press the

[ ](Standby/On) switch to turn on the power. Press

the [ ](Standby/On) switch again to turn the power

off.

Backup data in the flash memory is loaded to the

instrument when the power is turned on. If no backup

data exists on flash memory, all instrument settings

are restored to the initial factory defaults when the

power is turned on.

• Even when the switch is in the “STANDBY” position, elec-

tricity is still flowing to the instrument at the minimum

level. When you are not using the instrument for a long

time, make sure you unplug the AC power adaptor from

the wall AC outlet.

• Never attempt to turn the power off when a “WRITING!”

message is shown in the display. Doing so can damage the

flash memory and result in a loss of data.

CAUTION

NOTICE

Owner’s Manual

16

Setting Up

Panel Controls and Terminals

Front Panel

q [ ](Standby/On) switch...................... page 15

w [MASTER VOLUME] control ................ page 15

e [DEMO/BGM] button .................... pages 31, 85

r [SCORE] button....................................page 32

t [LYRICS] button....................................page 33

y [REC] button .........................................page 56

u LESSON START

[WAITING] button..............................page 38

[YOUR TEMPO] button .....................page 40

[MINUS ONE] button.........................page 41

i [P.A.T. ON/OFF] button ........................page 44

o [EASY SONG ARRANGER]

button ....................................................page 54

!0 Song Track

[1]–[5], [A] buttons....................pages 57, 84

Lesson

[R/1] and [L/1] buttons .....................page 38

!1 [METRONOME ON/OFF]] button .........page 22

!2 [TEMPO/TAP] button.............. pages 22, 79, 83

!3 SONG

[REPEAT&LEARN] button................page 42

[A-B REPEAT] button........................page 84

[REW] button.....................................page 31

[FF] button.........................................page 31

[PAUSE] button .................................page 31

[START/STOP] button .......................page 29

!4 STYLE

[ACMP ON/OFF] button.................... page 25

[INTRO/ENDING/rit.] button ............. page 76

[MAIN/AUTO FILL] button ................ page 76

[SYNC STOP] button ........................ page 78

[SYNC START] button.......................page 77

[START/STOP] button............... pages 24, 26

!5 REGIST MEMORY [BANK],

[1]–[4] buttons...................................... page 62

!6 CATEGORY [

r

] and [

f

] buttons ....... page 35

!7 [EXIT] button ........................................ page 36

!8 [FUNCTION] button...................... pages 36, 86

!9 DATA ENTRY

Dial, Number buttons [0]–[9],

[+] and [-] buttons............................. page 35

@0 [FILE CONTROL] button...................... page 90

@1 [EXECUTE] button ...............................page 92

@2 [PORTABLE GRAND] button............... page 19

@3 [SONG] button......................................page 28

@4 [STYLE] button.....................................page 24

@5 [VOICE] button ..................................... page 18

@6 [MUSIC DATABASE] button................. page 53

@7 [SPLIT ON/OFF] button ....................... page 21

@8 [DUAL ON/OFF] button........................ page 20

@9 [HARMONY ON/OFF] button ...............page 65

#0 [PITCH BEND] wheel ........................... page 68

#1 Drum Kit ............................................... page 19

The illustrations next to each key indicate the drum and per-

cussion instruments assigned to the keys when “Standard Kit

1” is selected.

#2 USB TO DEVICE terminal............ pages 30, 90

q

w

ert

io

y

u

!0

!3

!4

!1 !2

Front Panel

Song List (Data List) Style List (Data List)

Panel Controls and Terminals

Owner’s Manual

17

Setting Up

Rear Panel

#3 CONTRAST knob .................................page 37

#4 USB TO HOST terminal........................page 97

#5 SUSTAIN jack .......................................page 13

#6 PEDAL UNIT jack ................................. page 14

#7 PHONES/OUTPUT jack........................ page 13

#8 DC IN jack............................................. page 13

!9

!6

!7 !8

@0

@1

@2

@3 @4 @5

@6

@7 @8 @9

#2

#6 #7 #8#5#4#3

#1

#0

Rear Panel

Voice List (Data List)

Music Database List (Data List)

Display (page 36)

Owner’s Manual

18

Quick Guide

Try Playing a Variety of Instrument Voices

In addition to piano, organ, and other “standard” keyboard instruments, this instru-

ment has a large range of voices that includes guitar, bass, strings, sax, trumpet,

drums and percussion, sound effects … a wide variety of musical sounds.

This procedure selects the main voice you will play on the keyboard.

1

Press the [VOICE] button.

The main voice selection display will appear.

The currently selected voice number and name will be highlighted.

2

Select the voice you want to play.

While watching the highlighted voice name rotate the dial. The avail-

able voices will be selected and displayed in sequence. The voice

selected here becomes the main voice.

For this example select the “117 Flute” voice.

Select and Play a Voice—MAIN

The currently selected voice

number and name

• See the separate Data List

for a complete list of the

available voices.

NOTE

Select 117 Flute

Quick Guide

Try Playing a Variety of Instrument Voices

Owner’s Manual

19

3

Play the keyboard.

Try selecting and playing a variety of voices.

Press the [EXIT] button to return to the MAIN display.

Preset Voice Types

When you just want to play piano, all you have to do is press one convenient button.

Press the [PORTABLE GRAND] button.

The “001 Live! Grand Piano” voice will be selected.

• Voice Settings (page 72)

NOTE

Adjusts

volume.

001–142

155–535

Instrument Voices

143–154

(Drum Kit)

Various drum and percussion sounds are assigned to

individual keys, via which they can be played. Details

on assigning instruments to keys are provided in the

Drum Kit List of the separate Data List.

Play the Grand Piano Voice

• When you press the [POR-

TABLE GRAND] button all

settings other than touch

sensitivity are turned off. The

dual and split voices will

also be turned off, so only

the Grand Piano voice will

play over the entire key-

board.

NOTE

Try Playing a Variety of Instrument Voices

Owner’s Manual

20

Quick Guide

Once you press the [DUAL ON/OFF] button to turn the dual function on, a second voice will sound

that will play in addition to the main voice when you play the keyboard. The second voice is known as

the “dual” voice. The currently selected dual voice name and number will be displayed in the MAIN

display.

Press the button a second time to turn the dual voice function off.

A suitable dual voice is automatically selected when you turn on this func-

tion, but you can easily select a different dual voice (page 73).

Play Two Voices Simultaneously—DUAL

Dual voice number and name

Two voices will sound

at the same time.

La page charge ...

Yamaha DGX-640 Le manuel du propriétaire

Ce manuel convient également à

Yamaha DGX-640 Le manuel du propriétaire

dans d''autres langues

Documents connexes