Modern Forms WS-3120-CH Guide d'installation

Modern Forms
Marque
Modern Forms
Modèle
WS-3120-CH
Taper
Guide d'installation
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014
INSTALLATION INSTRUCTION
Vogue
WS-3120
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.
HARDWARE
A1
B1
C1
Technology Upgraded
No Driver Required
Driver
(Please direct wire with 120V AC)
Wire Connector
Qty: 3
Junction Box Screw
Qty: 2 + 1 Extra
Mounting Screw
Qty: 4 + 1 Extra
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014
INSTALLATION INSTRUCTION
Vogue
WS-3120
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the mounting hardware.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary
for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove screws (C1) from the xture and remove Connectors (A1).
4. Connect the xture wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.
Fixture and junction box ground wires should be connected to mounting plate using green screw provided. After wires are
connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
5. Secure mounting backplate (D1) to the junction box (F1) using junction box screws (B1).The side of the mounting backplate
marked “GND” must face out.
6. Place the xture’s canopy plate (L1) over the mounting back plate
(D1) and secure with screws (C1).
7. Slide the glass shade (G1) onto the front bracket (M1).
While supporting the glass, attach glass holders (H1) to
the front bracket with screws (N1) to secure the glass in place.
I1
F1
A1
D1
B1
C1
M1
L1
N1
H1
G1
Junction Box
Ground Wire
Wire Connector
Mounting Backplate
Junction Box Screw
Canopy Plate
Screw
Front Bracket
Glass
Glass Holders
Fixture Screw
Fixture output wires - Red
Blue xture wire
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
  • Page 1 1
  • Page 2 2

Modern Forms WS-3120-CH Guide d'installation

Modern Forms
Marque
Modern Forms
Modèle
WS-3120-CH
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents