Covers Parts #8038, 8039
LED Light Kit Installation Instructions (fits #8130 bodies)
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
HKC18101-R02 Rev 190405
LED Lighting Module Installation (Fig. 1) (#8038 Kit only):
1. Install the LED lighting
module (A) on the left
chassis floor pan. Secure
with the 2.5x15mm cap
screws (2).
2. Remove the screws from
the receiver box cover and
wire clamp; remove the
cover and clamp (B).
3. Remove the two 3x10mm
countersunk cap screws
from the battery tray (C).
4. Lift up the battery tray and
route the red wire (male
connector) from the LED
lighting module to the
right side of the chassis,
between the two T-Lock
servos, and through the
hole in the receiver box.
Plug the connector into
channel 1 of the receiver
(D). Note: The connector
can be plugged into any
non-telemetry channel on the TQi receiver.
5. Apply an additional bead of silicone grease (Traxxas part #1647, sold
separately) to the wire clamp. The grease will improve sealing. Reinstall the
clamp and screws.
6. Make sure the o-ring is properly seated into the groove in the receiver box so
that the cover will not pinch it or damage it in any way.
7. Install the cover and screws. Inspect the cover to make sure the o-ring seal is
not visible.
8. Reinstall the screws in the battery tray.
9. Connect the black wire (red female connector) from the LED lighting module
to the red wire (male connector) exiting the XL-5 HV electronic speed control.
LED Headlight Installation (Fig. 6)
1. Remove the 2.5x6mm button-head screw from each headlight assembly and
remove the assemblies (E) from the grille (see Assembly Diagram, Fig. 6).
Retain and reuse the plastic headlight mounts and hardware.
2. Install the chrome reflectors (F) (2) onto
the circuit boards of the LED headlight
harnesses (G) (Fig. 2).
Note: The reflectors must be installed
correctly to sit flat against the circuit
boards. Align the keying features (pegs
on the reflectors with holes in the
circuit boards). Also, there is a notch
on the bottom side of the reflectors
for clearance of the wires on the
circuit boards.
3. Install the circuit boards into the
existing plastic headlight mounts (H);
then, install the headlight lens (I) over
the chrome reflectors and onto the
circuit boards (Fig. 3).
Note: Align the keying features (pegs
on the lens with holes in the circuit
boards and headlight mounts).
4. Install complete left and right headlight
assemblies into the front grille and secure with the 2.5x6mm button-head
screws removed during disassembly.
5. Snap the LED side marker lights into the receptacles near each headlight.
LED Tail Light Installation (Fig. 6)
Note: The tail light harness (J) has 5mm LEDs with a red color band near the
connector and has a long and short wire lead.
1. Install the short wire of the harness on the left side (driver side) of the
vehicle body.
2. Snap the tail light LEDs into the tail light receptacles.
Wire Routing (Fig. 7)
When installing the LED light harnesses, note where the installation begins and
ends in the Wiring Diagram (Fig. 7). Install the included zip tie mounts and use
zip ties to secure the wiring to the body in the locations provided. The zip ties
do not need to be tight; allow some slack for wire movement.
Fig. 1
A
B
C
D
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
F
E
Assembly Diagram Fig. 6
F
G
E
J
I
#8038 Kit Contents:
• LED lighting module
• Distribution block
• Distribution block mount
• Headlight harness assembly
• Tail light harness
• Jumper
• Headlight reflector (2)
• 2.6x8mm button-head screws (2)
• 2.5x15mm cap screws (2)
• Zip ties (10)
• Zip tie mount (2)
• Double-sided adhesive foam tape
#8039 Kit Contents:
• Distribution block
• Distribution block mount
• Headlight harness assembly
• Tail light harness
• Jumper
• Headlight reflector (2)
• 2.6x8mm button-head screws (2)
• Zip ties (10)
• Zip tie mount (2)
• Double-sided adhesive foam tape
• 2.0mm hex wrench
• 1.5mm hex wrench
• Side cutters (to trim zip ties)
Tools required:
G
H
H
I
L
M
2.5x6 BCS
2.5x6 BCS
2.6x8 BCS
1.6x5 BCS
Fig. 2
Fig. 3
K
Wiring Diagram
Distribution Block Installation
1. Remove the 1.6x5mm button-head screws (2) from the driver
side (left side) door handle mount (K). Remove the mount.
2. Peel the backing from the included adhesive foam tape and
attach it to the flat surface on the back of the distribution
block mount (L) (Fig. 4). Do not remove the backing from the
other side of the tape yet.
3. Install the distribution block mount and secure with the
1.6x5mm button-head screws (2) as shown in Fig. 5.
4. Gently flex the body away from the distribution block mount
and remove the backing from the other side of the foam tape.
Press the body against the mount to adhere it to the mount.
5. Plug the connectors from the LED light wire harnesses into the ports of the distribution block (M).
Match the color band on the wire harnesses with the corresponding color of each port indicator on
the distribution block (white for headlights and front side marker lights, red for tail lights).
6. Plug the included jumper into the green port of the distribution block as indicated (see Wiring
Diagram, Fig. 7). Note: The jumper will allow the LED lights to go into full power (high beam) mode.
The jumper is not required for the LED lights to function (the lights will remain in low power (low
beam) mode if the jumper is not used).
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
Fig. 7
Fig. 4
Fig. 5
2.6x8 BCS
2.6x8 BCS
1.6x5 BCS
3mm
Location
Marking
3mm
Before installing the body (with the
LED light kit installed) on the chassis,
trim the front inner fenders as shown
below for additional side marker
light clearance.
Note: If the inner fenders have a
dot below the location marking (see
illustration to the right), no trimming
is required!
YELLOW*
GREEN (Jumper)
Headlight and Front Side Marker Light Wiring
Tail Light Wiring
FRONT
BOTTOM VIEW
To LED
Lighting Module
DISTRIBUTION BLOCK
DISTRIBUTION BLOCK PORTS
RED (Tail Light
Wiring)
WHITE (Headlight &
Front Side Marker
Light Wiring)
*For use with optional accessories.
Not used with this LED light kit.
-
1
-
2
Traxxas TRX-4 Blazer Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Traxxas TRX-4 Bronco Mode d'emploi
-
-
Traxxas TRX-4 G 500 4X4² Mode d'emploi
-
-
-
-
-
-
-
Traxxas TRX-4 Defender Mode d'emploi