Crestron AM-200 Mode d'emploi

Marque: Crestron

Modèle: AM-200

Taper: Mode d'emploi

DO GUIDE

AM-200

AirMedia

Presentation System 200

Mount Onto a Flat Surface

Use the four included anchors to mount the device onto a at surface.

NOTE: The anchors are best suited for surfaces with 3/8” to 3/4” thickness.

DO Install the Device

The Crestron

AM-200 can be mounted onto a rack rail or onto a at surface.

Mount Onto a Rack Rail

Use two mounting screws (not included) to mount the left or right mounting ange of the device onto

the front or rear rail of a rack.

DO Check the Box

QTY ITEM PART NUM.

4 Anchor, Wall, Plastic, Self Drill, #8 x 1-1/4" Screw 2050199

1 Cable, USB 2.0, A - Micro B, 6' (1.83 m) 2038114

1 Connector, 4-Pin 2003576

1 Connector, 5-Pin 2003577

1 Power Pack, 24 Vdc, 0.75 A, 100-240 Vac 2045865

DO GUIDE

DOC. 8260B (2050596) 05.18

Specications subject to change without notice.

DO Connect the Device

Make connections to the device as shown in the following diagrams. Use Crestron power supplies for

Crestron equipment.

AM-200 Top Panel Connections

NOTE: Observe the following when making connections to the device:

• PoE-type networks connected to these ports are for intrabuilding use only and should not

be connected to lines that run outside of the building in which this product is located.

• The device can receive power over PoE (IEEE 802.3af) or the included power pack.

AM-200 Bottom Panel Connections

DO Congure the Device

Use the device’s web interface to congure the device. For details on conguring the device, refer to

the AM-200/AM-300 Product Manual (Doc. 8254) at www.crestron.com/manuals.

DO Learn More

Visit the website for additional information and the latest rmware updates. To learn

more about this product, use a QR reader application on your mobile device to scan

the QR image.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL

Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

This unit is for indoor use only. It is not intended for outdoor use.

Cet appareil est réservé à une utilisation en intérieur. Il n’est pas destiné à une utilisation en extérieur.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools

License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements

can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.

The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.

The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.

Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.

Crestron, the Crestron logo, AirMedia, and Crestron Toolbox, are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. HDMI

and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks or registered

trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer

to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in

typography or photography.