Amana NFW7200TW Manuel utilisateur

Marque: Amana

Modèle: NFW7200TW

Catégorie: Machines à laver

Taper: Manuel utilisateur

TABLE OF CONTENTS

Safety Instructions ................................................ 1-2

Operating Instructions ............................................ 3

Using the Controls .............................................. 4-8

Water Use ................................................................. 8

Detergent Use .......................................................... 9

Features ................................................................ 9-10

Care and Cleaning ................................................. 11

Storing the Washer ................................................ 12

Troubleshooting ............................................... 12-14

Operating Sounds.....................................................15

Warranty .................................................................. 16

Guide d’utilisation et d’entretien ....................... 17

Guía de Uso y Cuidado ........................................ 34

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 2

W1016102

G U I D E

U S E & C A R E

W a s h e r

WELCOME

Welcome and congratulations on your

purchase of a Amana washer! Your complete

satisfaction is very important to us.

For best results, we suggest reading this

material to help acquaint you with proper

operating and maintenance procedures.

Should you need assistance in the future, it is

helpful to:

1) Have complete model and serial number

identification of your washer.

Date of Purchase ____________________

Model Number ______________________

Serial Number ______________________

2) IMPOR TANT: Keep this guide

and the sales receipt in a safe

place for future reference. Proof

of original purchase date is

needed for warranty service.

If you have questions, call:

Customer Assistance

1-800-843-0304 USA

1- 866-587-2002 CANADA

(Mon.–Fri., 8am–8pm Eastern Time)

Internet: http://www.amana.com

NOTE: In our continuing effort to

improve the quality of our

appliances, it may be necessary to

make changes to the appliance

without revising this guide.

For service and warranty

information, see page 16.

SAVE THESE INSTRUCTIONS

MPORTANT SAFETY INSTRUCTIONS

read before operating your washer

RECOGNIZE SAFETY SYMBOLS, WORDS, LABELS

WARNING – Hazards or unsafe practices which COULD result in severe

personal injury or death.

Warning and Important Safety Instructions appearing in this manual are not

meant to cover all possible conditions and situations that may occur. Common

sense, caution, and care must be exercised when installing, maintaining or

operating appliance.

Always contact your manufacturer about problems or conditions you do not

understand.

WHAT YOU NEED TO KNOW ABOUT

SAFETY INSTRUCTIONS

WARNING

CAUTION – Hazards or unsafe practices which COULD result in minor

personal injury or property damage.

CAUTION

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 3

To reduce the risk of fire, electric shock or injury to persons

when using the appliance, follow basic precautions, including

the following:

WARNING

1. Read all instructions before using the appliance.

2. As with any equipment using electricity and having moving

parts, there are potential hazards. To use this appliance

safely, the operator should become familiar with the

instructions for operation of the appliance and always

exercise care when using it.

3. Do not install or store this appliance where it will be

exposed to the weather.

4. Install and level the clothes washer on a floor that can

support the weight.

5. This appliance must be properly grounded. Never plug

the appliance cord into a receptacle which is not

grounded adequately and in accordance with local and

national codes. See installation instructions for grounding

this appliance.

6. To avoid the possibility of fire or explosion:

• Do not wash items that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, or other

flammable or explosive substances as they give

off vapors that could ignite or explode. Hand

wash and line dry any items containing these

substances.

Any material on which you have used a cleaning

solvent, or which is saturated with flammable

liquids or solids, should not be placed in the

clothes washer until all traces of these liquids or

solids and their fumes have been removed.

These items include acetone, denatured alcohol,

gasoline, kerosene, some liquid household cleaners,

some spot removers, turpentine, waxes and wax

removers.

• Do not add gasoline, dry-cleaning solvents, or other

flammable or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

• Under certain conditions, hydrogen gas may be

produced in a hot water system that has not

been used for 2 weeks or more. HYDROGEN

GAS IS EXPLOSIVE. If the hot water system has

not been used for such a period, before using a

washing machine or combination washer-dryer,

turn on all hot water faucets and let the water

flow from each for several minutes. This will

release any accumulated hydrogen gas. As the

gas is flammable, do not smoke or use an open

flame during this time.

7. Unplug power supply cord before attempting to service

your clothes washer.

8. Do not reach into the appliance if the tumbler is moving.

9. Do not allow children to play on or in the appliance.

Close supervision of children is necessary when the

appliance is used near children.

10. Do not tamper with controls.

11. Do not repair or replace any part of the appliance or

attempt any servicing unless specifically recommended in

published user-repair instructions that you understand

and have the skills to carry out.

12. Store laundry aids and other material in a cool, dry place

where children cannot reach them.

13. Do not wash or dry items that are soiled with vegetable

or cooking oil.These items may contain some oil after

laundering. Due to the remaining oil, the fabric may smoke

or catch fire by itself.

14. Do not use chlorine bleach and ammonia or acids (such

as vinegar or rust remover) in the same wash. Hazardous

fumes can form.

15. Do not machine wash fiberglass materials. Small particles

can stick to fabrics washed in following loads and cause

skin irritation.

16. Before the appliance is removed from service or

discarded, remove the door to the washing compartment.

17. Do not sit on top of the clothes washer.

18. Inlet hoses are subject to damage and deterioration over

time. Check the hoses periodically for bulges, kinks, cuts,

wear or leaks and replace them every five years.

MPORTANT SAFETY INSTRUCTIONS

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 4

OPERATING INSTRUCTIONS

NOTE: To ensure that your additional items get clean,

do not wait more than five minutes after the cycle has

started to add the item.

LOAD THE CLOTHES WASHER

1. Load the washer loosely – DO NOT overload.

2. Close the door.

3.Add detergent and additives to the dispenser

(see pages 9-10).

4. Select the appropriate cycle and options for the load,

(see pages 4-7).

NOTES:

• When the cycle is complete, the Door Lock light will go out and “End” or “00” (select models) will appear in the

display.

• DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see “Load the Clothes

Washer” section.

• When the washer is restarted after a pause, there will be a delay of up to 15 seconds before the cycle will continue.

• Pressing

Power Off cancels the cycle and stops the washer.

• The Wash, Rinse and Spin indicator lights will illuminate during those portions of the cycle.

GETTING STARTED

5. Press the Cycle Selector dial.

6.The Wash Indicator light will illuminate.

7.The estimated cycle time will appear in the display.

The time may fluctuate to better indicate the

wash time remaining in the cycle.

8. Before the washer starts to fill, it will make a

series of clicking noises to check the door lock

and do a quick drain.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 5

• The tub can be loaded completely full with dry,

unfolded clothes. However, DO NOT pack the tub

tightly.

• Overloading may reduce washing efficiency, cause

excess wear and possibly cause creasing or wrinkling of

the load.

• Wash delicate items such as bras, hosiery and other

lingerie in the Delicates or Hand Wash

cycle with

similar lightweight items.

• When washing big bulky items or a couple of small

items that do not fill the tub completely, such as a rug, a

few towels should be added for improved tumbling and

spin performance.

• When washing smaller, bulky items that do not fill the

tub completely such as a rug, one pillow, stuffed toys or

one or two sweaters, a few towels should be added for

improved tumbling and spin performance.

• When washing heavily soiled loads, it is very important

to avoid overloading the washer to assure good

cleaning results.

• To add a forgotten item in the Super Wash, Normal,

Wrinkle Control or Quick Wash cycles, press the Cycle

Selector dial, wait for the Door Lock light to go out

(5 seconds), add the item, close the door and press the

Cycle Selector dial. After a pause of one to two

minutes, the cycle will resume.

• Close door carefully to avoid slamming.

USING THE CONTROLS

Select the appropriate cycle for the type of load.

This will determine the tumble pattern and spin speed for the cycle.

Step 1

NOTE: To minimize wrinkling of loads, select the Wrinkle Control cycle.

SELECT CYCLE

Super Wash – For sturdy, colorfast fabrics and heavily soiled garments.

Normal – For most fabrics including cottons, linens and normally soiled garments.

Delicates – For sheer fabrics, bras and lingerie.

Hand Wash – For wool, silk and other hand-wash-only fabrics.

For best results, use liquid detergent.

Quick Wash – For lightly soiled or wrinkled garments needed quickly.

Wrinkle Control – For “wash and wear” and synthetic fabrics and lightly to normally

soiled garments.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 6

USING THE CONTROLS

Step 2

Press the arrow pad to select the wash and rinse water temperatures. Follow

the garment care label and chart below for best results.

Hot/Cold – Whites and heavily soiled color-fast items.

ATC Warm/Warm – Color-fast items.When warm rinse is selected, only

the final rinse will be warm.The other rinses will be cold to conserve energy.

ATC Warm/Cold – Moderately soiled, color-fast items; most wrinkle free

items.

ATC Cold/Cold – Brightly colored, lightly soiled items.

Cold/Cold – Brightly colored, very lightly soiled items; washable woolens.

SELECT WASH/RINSE WATER TEMPERATURES

IMPORTANT: The washer features an automatic temperature control (ATC) to provide a warm wash of approximately 105˚ F, a cold wash of

approximately 65˚ F and a warm rinse of approximately 80º F in the final rinse only on the ATC temperature selections.

REMEMBER: In wash water temperatures below 65

F, detergents do not dissolve well or clean well.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 7

Step 3

Press the arrow pad to select the spin speed.

High – Use for underwear, t-shirts, jeans and sturdy cottons.

Medium – Use for jeans, wrinkle free or “wash-and-wear” items and

synthetics.

Gentle – Use for items that will be hung up or laid flat to dry.

Low–Use for delicate items needing a slow spin speed because of fabric and

construction.

SELECT SPIN SPEED

USING THE CONTROLS

Step 5

SELECT CYCLE OPTIONS

Heavy – Use for cleaning heavily soiled loads.

Medium – Use for cleaning moderately soiled loads.This setting will be

appropriate for most loads.

Light – Use for cleaning lightly soiled loads.

Step 4

SELECT SOIL LEVEL

Press the arrow pad to select the Soil Level/washing time.

cont.

Press the appropriate pad(s) to select one or more options.The indicator light

above the pad will illuminate when the option is selected.

Delay –

1. Make the appropriate selections for your load.

2. Press the Delay pad until the desired delay time appears

in the display.

3. Press the Cycle Selector dial.The delay time will

start counting down.

4. To cancel a delay, press the Power Off pad and restart.

Chime – Press the Chime pad to increase or decrease the end of cycle signal

volume or turn the signal off.

Control Lock – The washer controls can be locked to prevent

unwanted use by children.

1. Press the Wash/Rinse Temp and Spin Speed pads at the same time

for three seconds.

2.The Control Lock light will illuminate.

3.To unlock, press the Wash/Rinse Temp and Spin Speed pads at the

same time for three seconds.The Control Lock light will go out.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 8

Any cycle can be delayed for up to 9 hours in one hour increments.

SELECT CYCLE OPTIONS, CONT.

Press the appropriate pad(s) to select one or more options.The indicator light above

the pad will illuminate when the option is selected.

Extra Rinse – Adds an additional rinse at the end of the cycle to more thoroughly

remove laundry additives and perfumes.

Rinse and Spin – Use for loads that need rinsing only or to add rinse-added fabric

softener to a load.

Spin Only – Provides a spin to remove more water from the load.

Step 6

To start the washer, press the Cycle Selector dial. Before the washer starts to fill,

it will make a series of clicking noises to check the door lock and do a quick drain.

Changing a Cycle

If an incorrect cycle has been accidentally selected:

1. Press the Cycle Selector dial.

2.Turn the Cycle Selector dial to the desired cycle.

3. Set the desired options for the cycle.

4. Press the Cycle Selector dial.The Wash indicator

lights stop flashing and the new cycle starts.

Canceling a Cycle

To cancel a cycle:

1. Press the Power Off pad.

2. Select the Rinse and Spin or Spin Only option pad.

3. Press the Cycle Selector dial.The Spin light illuminates

and the washer starts the rinse or spin.

START THE WASHER

USING THE CONTROLS

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 9

WATER USE

After setting the cycle and pressing Cycle Selector dial, the display will show the

estimated minutes remaining in the cycle.The estimated time remaining may fluctuate to

better indicate the wash time left in the cycle.

Door Lock – lights whenever the door of the clothes washer is locked.The door can

be unlocked by pressing the Cycle Selector dial to pause the washer.

Control Lock – The washer controls can be locked to prevent unwanted use by

children.

1. Press the Wash/Rinse Temp and Spin Speed pads at the same time for

three seconds.

2.The Control Lock light will illuminate.

3.To unlock, press the Wash/Rinse Temp and Spin Speed pads at the same

time for three seconds.The Control Lock light will go out.

Cycle Indicator Lights – The Wash, Rinse and Spin lights at the top of the control

panel will illuminate progressively to indicate when the washer is in those portions of the

cycle.These lights will flash when the cycle has been paused.

Pad Indicator Lights – The indicator lights above the pads will illuminate when the

pad is selected.

Cycle Setting Indicator Lights – Indicator lights by the cycle settings will illuminate

when the selection is made.

The amount of water used will vary with each load.The Amana clothes washer will automatically provide

the appropriate amount of water for efficient cleaning performance and conservation of water and energy.

Fill time will vary depending on water pressure.

ESTIMATED TIME DISPLAY

INDICATOR LIGHTS

USING THE CONTROLS

WATER LEVEL CONTROL

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 10

DETERGENT USE

FEATURES

Your Amana washer is designed

to use high efficiency (HE) detergents.

• For best cleaning results, use a high

efficiency detergent such as Tide HE,Wisk HE, Cheer

HE or Gain HE*. High efficiency detergents contain

suds suppressors which reduce or eliminate suds.

When less suds are produced, the load tumbles more

efficiently and cleaning results are maximized.

The washer has separate compartments for

dispensing detergent and color-safe bleach, chlorine

bleach and fabric softener. All laundry additives are

added to their respective compartments before

starting the washer.

AUTOMATIC DISPENSER

NOTE: If using liquid detergent, lower the

Detergent Selector and add the detergent to the

Detergent Compartment.

DETERGENT COMPARTMENT

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 11

The Automatic Dispenser MUST ALWAYS

be in place before starting the washer. DO

NOT open the Automatic Dispenser when

the washer is running.

To use:

1. Pull out the dispenser drawer on the left

side of the control panel.

2. Fill appropriate compartments with laundry

additives, being careful not to overfill or spill

additives.

3. Slide the dispenser drawer carefully and

completely back into the compartment.

1. Pour the recommended amount of laundry

detergent directly into the detergent compart-

ment before starting the washer.

2. If color-safe bleach is to be used, it should be

added with detergent to the detergent

compartment.

• When adding color-safe bleach with detergent,

it is best if both laundry products are in the

same form; granular or liquid.

POWDER

LIQUID

SOFTENER

Detergent

Selector

Detergent

Compartment

* Brand names are trademarks of the respective manufacturers.

FEATURES

BLEACH COMPARTMENT

(Liquid Chlorine Bleach Only)

1. Add chlorine bleach to the Bleach

Compartment. DO NOT exceed the MAX FILL

line.

2. Avoid splashing or over-filling the compartment.

3.The washer automatically dispenses bleach into

the tub at the appropriate time.

4.The dispenser automatically dilutes liquid chlo-

rine bleach before it reaches the wash load.

1. Pour the recommended amount of liquid fabric

softener into the softener compartment. For

smaller loads, use less than one cap full.

2. Fabric softener should be diluted with warm water

until it reaches MAX FILL in the compartment.

3.The dispenser automatically releases liquid fabric

softener at the proper time during the rinse cycle.

FABRIC SOFTENER COMPARTMENT

NOTES:

• Never pour undiluted liquid chlorine

bleach directly onto the load or into

the tub. It is a powerful chemical and can

cause fabric damage, such as weakening of the

fibers or color loss, if not used properly.

• If you prefer to use color-safe, non-chlorine

bleach, add it to the appropriate detergent

compartment. DO NOT pour color-safe

bleach into the chlorine bleach

dispenser.

NOTES:

• Use the softener compartment ONLY for

liquid fabric softeners.

• DO NOT use the Downy Ball

with this

washer. It will not add fabric softener at the

appropriate time. Use the automatic dispenser.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 12

POWDER

LIQUID

SOFTENER

Bleach

Compartment

Fabric Softener

Compartment

Turn off the water faucets after finishing the

day’s washing. This will shut off the water supply to

the clothes washer and prevent the unlikely possibility of

damage from escaping water. Leave the door open to

allow the inside of the washer to dry out.

Use a soft cloth to wipe up all detergent, bleach or other

spills as they occur.

Clean the following as recommended:

Control Panel – Clean with a soft, damp cloth. Do not

use abrasive powders or cleaning pads. Do not spray

cleaners directly on the panel.

Cabinet – Clean with soap and water.

The Automatic Dispenser may need to be cleaned

periodically due to laundry additive buildup.

1. Press the release lever on the inside of the

dispenser and pull out.

2. Remove the cups from the fabric softener and

bleach compartments.

3.Wash all of the parts under running water.

4. Clean the dispenser recess with a soft brush.

5. Reinsert the cups, pushing them firmly into

place.

6. Push the dispenser back into place.

7. Run a Rinse & Spin cycle without any load in the

washer.

CARE AND CLEANING

CLEANING THE DISPENSERS

Clean the interior of the washer periodically to

remove any dirt, soil, odor, mold, mildew or bacteria

residue that may remain in the washer as a result of

washing clothes. We recommend taking the

following steps every 60 to 120 days to clean and

freshen your washer interior. The frequency with

which the washer should be cleaned and freshened

depends on factors such as usage, the amount of

dirt, soil or bacteria being run through your washer,

or the use of cold water. Failure to follow these

instructions may result in unsatisfactory conditions,

including unpleasant odor and/or permanent stains

on the washer or washload.

CLEANING THE INTERIOR

To clean and freshen the washer interior:

1. Make a solution of one cup chlorine bleach and two cups

warm water. Be careful not to spill or splash the bleach

solution.

2. Wipe the door seal with bleach solution and a soft cloth.

3. Fill bleach dispenser with undiluted chlorine bleach.

4. Run the washer through a complete cycle using hot

water.

5. Repeat the wash cycle if necessary.

Hard water deposits may be removed, if needed. Use a

recommended cleaner labeled clothes washer safe.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 13

BLEA CH

S OFTE NER

Siphon

Cap

POWDER

LIQUID

SOFTENER

STORING THE CLOTHES WASHER

TROUBLESHOOTING

• See Cleaning the Interior, page 11.

• Make sure door is firmly closed.

• Make sure the washer is plugged in.

• Make sure the water source faucets are turned on.

• Make sure to press the

Cycle Selector dial to start the washer.

• Make sure the Control Lock is not activated, see page 6.

• Before the washer starts to fill, it will make a series of clicking noises to check the door lock

and do a quick drain.

• Turn both faucets on fully.

• Make sure the door is tightly closed.

• Make sure the washer is plugged in.

• Check fuse or reset circuit breaker.

• Press the

Cycle Selector dial to start the washer.

• Straighten water inlet hoses.

• Disconnect hoses and clean screens. Hose filter screens may be plugged.

• Open and close the door, then press the

Cycle Selector dial.

• Make sure the washer is running with sufficient water pressure.

See Installation Instructions.

• Make sure the Detergent Selector is in the upper position when using granular detergent.

• Make sure the washer is set on a level surface. If the surface is not level, adjust the washer

feet to level the appliance. See Installation Instructions.

• Make sure that the shipping bolts are removed. See Installation Instructions.

• Make sure the washer is not touching any other object.

• Make sure the laundry load is balanced.

Washer vibrates or

is too noisy

Detergent remains in

the automatic

dispenser after the

wash cycle is complete

No water or

insufficient water

supply

The washer will not

start

CONT.

• Disconnect the clothes washer from the electrical

supply and leave the washer door open to let air

circulate inside the tumbler.

• If the washer has been stored in below-freezing

temperatures, allow time for any water left over in the

washer to thaw out before use.

CHECK THESE POINTS IF YOUR WASHER ...

Freshening your

washer

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 14

Washers can be damaged if water is not removed from hoses

and internal components before storage. Prepare the washer

for storage as follows:

• Select the Quick Wash

cycle and add bleach to the

automatic dispenser. Run the washer through the cycle

without a load.

• Turn the water faucets off and disconnect the inlet hoses.

For information on long-term storage or storage of your

washer during extreme cold temperatures,

call Customer Service toll-free at

1-800-843-0304 USA or 1-866-587-2002 Canada.

Fills with the

Wrong

Temperature

Water

• Plug cord into live electrical outlet.

• Check fuse or reset circuit breaker.

• Close door and press the Cycle Selector dial to start the washer. For your safety, the washer

will not tumble or spin unless the door is closed.

• Before the washer starts to fill, it will make a series of clicking noises to check the door lock

and do a quick drain.

• This may be a pause or soak period in the cycle.Wait briefly and it may start.

• Check screens on inlet hoses at the faucets for obstructions. Clean screens periodically.

• Turn both faucets on fully.

• Make sure temperature selection is correct.

• Make sure hoses are connected to correct faucets. Flush water lines.

• Check the water heater. It should be set to deliver a minimum 120° F (49° C) hot water at

the tap.Also check water heater capacity and recovery rate.

• Disconnect hoses and clean screens. Hose filter screens may be plugged.

• As the washer is filling, the water temperature may change as the automatic temperature

control feature checks incoming water temperature.This is normal.

• While the washer is filling, you may notice just hot and/or just cold water going through the

dispenser when cold or warm wash temperatures are selected. This is a normal function of

the automatic temperature control feature as the washer determines the temperature of the

water.

• Check fuse or reset circuit breaker.

• Close the door and press the

Cycle Selector dial. For your safety, the washer will not

tumble or spin unless the door is closed.

• Press the

Cycle Selector dial to stop the washer.

• The washer door will remain locked during the heating portion of the Sanitary Cycle

(select models).

• It may take a few moments for the door lock mechanism to disengage.

• Check fuse or reset circuit breaker.

• Straighten drain hoses. Eliminate kinked hoses. If there is a drain restriction, call for service.

• Close the door and press the

Cycle Selector dial. For your safety, the washer will not

tumble or spin unless the door is closed.

• Use the High or Max Extract spin speed.

• Use high efficiency detergent to reduce over-sudsing.

• Load is too small. Very small loads (one or two items) may become unbalanced and not spin

out completely.

• Make sure door is firmly closed.

• Make sure hose connections are tight.

• Make sure end of drain hose is correctly inserted and secured to drain facility.

• Avoid overloading.

• Use high efficiency detergent to prevent over-sudsing.

• Reduce detergent amount for soft water, small or lightly soiled loads.

TROUBLESHOOTING

Load is too wet

at end of cycle

The washer does

not drain and/or

spin

Won’t tumble

Door locked shut;

will not open

Stops

Leaks Water

For further assistance, call Customer Service toll-free at 1-800-843-0304 USA or 1-866-587-2002 Canada.

Ex cessiv e Suds

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 15

CHECK THESE POINTS IF YOUR WASHER ...

Information codes may be displayed to help you better understand what is occurring with the washer.

INFORMATION CODES

TROUBLESHOOTING

For any codes not listed above, call Customer Service at 1-800-843-0304 USA or 1-866-587-2002 Canada.

Unbalanced load prevented the washer from

spinning.

Door is unlocked when washer is running.

Door is open when washer is running.

The washer failed to lock the door.

Water temperature control problem.

(Heater Control problem)

The washer has tried to fill but has not reached

the proper water level.

The door will not unlock.

Motor not running properly.

The washer is not draining.

The washer has tried to fill but was unsuccessful.

Problem with control.

Electric service was lost when washer was

running.

Redistribute the load, press the

Cycle Selector

dial.

Press

Power Off pad then restart the cycle. If the

code reappears, call for service, see below.

Close the door tightly and restart the cycle.

If the code reappears, call for service, see below.

Close the door tightly and restart the cycle.

If the code reappears, call for service, see below.

Call for service, see below.

Make sure the door is firmly closed.

Push the

Power Off pad to turn off the washer, and

then turn it on using any pad. If the code reappears,

call for service, see below.

Restart the cycle pressing the

Cycle Selector dial.

If the code reappears, call for service, see below.

See Troubleshooting “The washer does not drain

and/or spin”, page 13. If problem continues, call for

service, see below.

Make sure the water faucets are open all the way.

Check for kinked hoses.

Check inlet screens on fill hoses.

Call for service, see below.

Restart the cycle by pressing the Cycle Selector

dial.



Code

Symbol Meaning Solution



DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 16

OPERATING SOUNDS

• The motor increases speed to spin the tub to remove moisture from the load.

• Detergent is dispensed at the start of the cycle. Bleach is dispensed during final

minutes of wash. Fabric softener is dispensed during the third rinse while the washer

is filling.

• The tub rotates one direction followed by a pause.The tub reverses direction and

pauses.This action continues throughout the cycle.

• After reaching the maximum spin speed, the machine may reduce spin speed slightly

for maximum performance.

• The tumbler will begin to accelerate to speed, then slows back down to redistribute

the load more evenly when an unbalanced load occurs.

• The Amana clothes washer uses a true adaptive fill and adds more water during the

wash cycle as it is needed.

• Water flows through the dispenser to dilute and add bleach or fabric softener at the

appropriate time.This will occur even if bleach and fabric softener are not used.

• Before the washer starts to fill, it will make a series of clicking noises to check the

door lock and do a quick drain.

• This is audio confirmation the door has locked successfully.

• Due to tub movement during the spin cycle, air is transferred in and out of the tub

to provide optimum performance.

• Water is being extracted through the drain holes in the spinner and is hitting the

outer tub before draining out of the machine.

Rhythmic air rushing

during spin.

Rapid snapping and/or

popping sound from the rear

of the washer during spin.

Washer beeps after

cycle has started.

High-pitched sound

during a spin cycle.

Clicking/draining sounds

when washer is started.

Water is added after

the washer has been

tumbling for a while.

The spin speed slows down

dramatically when it sounds

like an out-of-balance load.

Washer maintains a slightly

reduced spin speed after

achieving a higher spin speed.

Flushing water sound

coming from the

dispenser area.

Whirring or sloshing sound

followed by a pause, repeated

throughout the wash cycle.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 17

CLOTHES WASHER WARRANTY

Warranty

Limited One Year Warranty -

Parts and Labor

For one (1) year from the original retail

purchase date, any part which fails in

normal home use will be repaired or

replaced free of charge.

Canadian Residents

The above warranties only cover an

appliance installed in Canada that has

been certified or listed by appropriate test

agencies for a compliance to a National

Standard of Canada unless the appliance

was brought into Canada due to transfer

of residence from the United States to

Canada.

The specific warranties expressed above are

the

ONLY warranties provided by the

manufacturer. These warranties give you

specific legal rights, and you may also have

other rights which vary from state to state.

What is Not Covered By These Warranties

1. Conditions and damages resulting from any of the following:

a. Improper installation, delivery, or maintenance.

b. Any repair, modification, alteration, or adjustment not authorized by the

manufacturer or an authorized servicer.

c. Misuse, abuse, accidents, unreasonable use, or acts of God.

d. Incorrect electric current, voltage, electrical and/or gas supply.

e. Improper setting of any control.

f. Use of risers (pedestals) that are not Maytag branded.

2. Warranties are void if the original serial numbers have been removed, altered,

or cannot be readily determined.

3. Light bulbs, water filters and air filters.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to:

a. Correct installation errors. For products requiring ventilation, rigid metal

ducting must be used.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to and from the servicer.

d. Correct issues related to risers that are not Maytag branded.

6. Any food loss due to refrigerator or freezer product failures.

7. Expenses for travel and transportation for product service in remote locations.

8. Outside of the United St ates and Canada this warranty does not apply.

Contact your dealer to determine if another warranty applies.

9. Consequential or incidental damages sustained by any person as a result of

any breach of the se warranties. Some states do not allow the exclusion or

limitation of consequential or incidental damages, so the above exclusion may

not apply.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call the

dealer from whom your appliance was purchased or call Amana Services,

Customer Assistance at 1-800-843-0304 USA and 1-866-587-2002 Canada to

locate an authorized servicer.

• Be sure to retain proof of purchase to verify warranty st atus. Refer to WARRANTY

for further information on owner’s responsibilities for warranty service.

• If the dealer or service company cannot resolve the problem, write to

Amana Customer Service, 553 Benson Road, Benton Harbor, MI 49022, or call

1-800-843-0304 USA and 1-866-587-2002 Canada.

• User’s guides, service manuals and parts information are available from Amana

Services, LLC, Customer Assistance.

Notes: When writing or calling about a service problem, please include:

a. Your name, address and telephone number;

b. Model number and serial number;

c. Name and address of your dealer or servicer;

d. A clear description of the problem you are having;

e. Proof of purchase (sales receipt).

CUSTOMER’S SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY S HALL BE PRODUCT REPAIR

AS PROVIDED HEREIN. IMPLIED

WARRANTIES, INCLUDING WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED

TO ONE YEAR OR THE SHORTEST

PERIOD ALLOWED BY LAW. AMANA

CORPORATION SHALL NOT BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. SOME STATES AND

PROVINCES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE

DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO

THESE EXCLUSIONS OR LIMITATIONS

MAY NOT APPLY TO YOU. THIS

WARRANTY GIVES YOU SPECIFIC LEGAL

RIGHTS AND YOU MAY ALSO HAVE

OTHER RIGHTS, WHICH VARY STATE TO

STATE OR PROVINCE TO PROVINCE.

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 18

D’UTILISATION ET

D’ENTRETIEN

GUIDE

D’UTILISATION ET

D’ENTRETIEN

TABLE DES MATIÈRES

Instructions de sécurité importantes .......... 18-19

Mode d’emploi ........................................................ 20

Utilisation des commandes ............................ 21-25

Consommation d’eau ..............................................25

Utilisation de détergent ....................................... 26

Caractéristiques ............................................... 26-27

Entretien et nettoyage .......................................... 28

Rangement de la laveuse ...................................... 29

Recherche de pannes ...................................... 29-31

Bruits de fonctionnement.......................................32

Garantie de la laveuse ........................................... 33

Guía de Uso y Cuidado ........................................ 34

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 19

L a v e u s e

ATTENTION – Risques ou pratiques non sûres qui POURRAIENT

résulter en blessures mineures ou dégâts matériels.

BIENVENUE

Bienvenue et félicitations pour votre achat

d’une laveuse Amana! Il est très

important pour nous que vous soyez

totalement satisfait. Pour l’obtention des

meilleurs résultats, nous vous suggérons de

lire la totalité de ce guide pour vous

familiariser avec les méthodes adéquates

d’utilisation et entretien de l’appareil.

Pour tout besoin d’assistance à l’avenir:

1) Il sera utile de disposer immédiatement du

numéro de modèle et du numéro de série

de l’appareil.

Date d’achat ________________________

Numéro de modèle __________________

Numéro de série ____________________

2) IMPORTANT : Conservez ce

guide et la facture ed'achat en lieu

sûr pour utilisation ultérieure.

Une preuve de la date d'achat

devra être présentée pour toute

demande de travaux sous

garantie.

Pour toute question, téléphonez à :

Service à la clientèle

1-866-587-2002 CANADA

(Lundi à vendredi, 8 h - 20 h, heure de l’Est)

Internet: http://www.amana.com

REMARQUE : Dans le cadre de nos

pratiques d’amélioration constante

de la qualité de nos appareils, des

modifications peuvent être

introduites sur les appareils sans

que cela donne lieu à une révision

de ce guide.

Pour l’information sur le service et

la garantie, voir page 33.

NSTRUCTIONS DE SÉCURITÉ IMPORTANTES

CONSERVER CES INSTRUCTIONS

lire ce qui suit avant d’utiliser la laveuse

Les consignes de sécurité et les mises en garde présentées dans ce guide ne

couvrent pas toutes les situations possibles. Faire preuve de jugement, de

prudence et d’attention lors de l’installation, de l’entretien et de l’utilisation de

l’appareil.

Lorsque survient un problème ou une situation inhabituelle, toujours communiquer

avec le fabricant.

CEQU’IL FAUT SAVOIR À PROPOS DES CONSIGNES

DE SÉCURITÉ

RECONNAÎTRE LES ÉTIQUETTES, PHRASES OU

SYMBOLES SUR LA SÉCURITÉ

AVERTISSEMENT – Risques ou pratiques non sûres, qui

POURRAIENT résulter en de graves blessures ou même la mort.

AVERTISSEMENT

ATTENTION

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 20

1. Lisez toutes les instructions avant d’utiliser l’appareil.

2. Comme avec tout équipement fonctionnant à l’électricité

et comportant des pièces mobiles, il existe toujours des

possibilités de dangers. Pour utiliser cet appareil dans les

meilleures conditions de sécurité, l’opérateur doit se

familiariser avec les instructions de fonctionnement de

l’appareil et user de prudence pendant son utilisation.

3. N’installez pas et ne remisez pas l’appareil dans un

endroit où il est exposé aux intempéries.

4. Installez l’appareil et mettez-le de niveau sur un plancher

pouvant porter son poids.

5. Cet appareil doit être correctement mis à la terre. Ne

branchez jamais le câble électrique de l’appareil sur une

prise murale non mise à la terre conformément aux

codes locaux et nationaux.Voyez les instructions

d’installation pour la mise à la terre de cet appareil.

6. Pour éviter les risques d’incendie ou d’explosion :

• Ne lavez pas d’articles qui ont auparavant été

nettoyés ou lavés à l’aide d’essence, de solvants

de nettoyage à sec ou d’autres produits explosifs

ou inflammables, ou qui en sont imbibés ou

éclaboussés, car ces substances produisent

des vapeurs qui peuvent s’enflammer ou

exploser. Lavez à la main et séchez à l’air tout

article contenant ces substances.

Tout tissu sur lequel des solvants de nettoyage ont été

utilisés ou qui est saturé de liquides ou solides

inflammables ne doit pas être mis dans la laveuse avant

que toute trace et toute vapeur de ces liquides ou

solides ne soient complètement éliminées.

Ces produits comprennent l’acétone, l’alcool dénaturé,

l’essence, le kérosène, certains produits de nettoyage

ménagers, les détachants, la térébenthine, les cires et

les décapants de cire.

• N’ajoutez pas d’essence, de solvants de nettoyage à sec

ou toute autre substance inflammable ou explosive à

l’eau de lavage. Ces substances produisent des vapeurs

qui peuvent s’enflammer ou exploser.

• Dans certaines conditions, il peut y avoir production

d’hydrogène dans un système de chauffage d’eau qui

n’est pas utilisé pendant 2 semaines ou plus.

L’HYDROGÈNE EST UN EXPLOSIF. Si votre système

de chauffage d’eau n’est pas utilisé sur une telle

période, ouvrez tous les robinets d’eau chaude et

laissez couler l’eau pendant plusieurs minutes avant

d’utiliser votre laveuse ou votre ensemble machine à

laver-sécheuse. Ceci élimine toute accumulation

d’hydrogène. Ce gaz étant inflammable, ne fumez pas et

n’utilisez pas de flamme vive pendant ces quelques

minutes.

7. Débranchez le cordon d’alimentation électrique avant

d’essayer de réparer la laveuse.

8. N’introduisez pas une main ou un bras dans l’appareil si la

cuve est en mouvement.

9. Ne permettez pas aux enfants de jouer sur ou à

l’intérieur de l’appareil. Une supervision étroite des

enfants est nécessaire lorsque l’appareil est utilisé à

proximité d’enfants.

10. Ne modifiez pas les mécanismes de commande.

11. Ne réparez pas ou ne remplacez pas une pièce de

l’appareil ou ne procédez pas à un dépannage, sauf si les

instructions publiées le recommandent et que la personne

effectuant la réparation les comprend et possède les

connaissances voulues pour les exécuter.

12. Rangez les produits pour la lessive dans un endroit frais

et sec hors d’atteinte des enfants.

13. Ne lavez pas ou ne séchez pas d’articles tachés d’huile

végétale ou de cuisson. Ces articles pourraient être

encore imprégnés d’huile après la lessive. Pour cette

raison, le tissu pourrait émettre des fumées ou prendre

feu de lui-même.

14. Ne mélangez pas de javellisant et d’ammoniaque ou

d’acides (tels que du vinaigre ou du produit pour enlever

la rouille) pour une même charge de linge. Des vapeurs

nocives peuvent se former.

15. Ne lavez pas d’articles en fibre de verre à la machine. De

petites particules peuvent se coller sur le linge lavé par la

suite et provoquer des irritations cutanées.

16. Avant de retirer l’appareil du service ou de le mettre au

rebut, retirez le couvercle du compartiment de lavage.

17. Ne vous asseyez pas sur la laveuse.

18. Les tuyaux d’alimentation se détériorent progressivement.

Inspectez les tuyaux à intervalle régulier; recherchez

dilatations, écrasements, coupures, fuites et indices

d’usure. Remplacez les tuyaux après 5 ans de service.

NSTRUCTIONS DE SÉCURITÉ IMPORTANTES

Pour minimiser les risques d’incendie, explosion, de choc

électrique, dommages matériels ou blessures lors de

l’utilisation de l’appareil, appliquer les précautions

fondamentales, dont les suivantes.

AVERTISSEMENT

DC68-02030B-01 MAH-3 12/15/05 3:11 PM Page 21

La page charge ...

Amana NFW7200TW Manuel utilisateur

Marque: Amana

Modèle: NFW7200TW

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Amana NFW7200TW User manual
español: Amana NFW7200TW Manual de usuario

Amana NFW7200TW Manuel utilisateur

Amana NFW7200TW Manuel utilisateur

dans d''autres langues

Autres documents