120
Press the car start button or
turn the ignition switch to the
START position.
4.
(RED & GREEN
flashes alternately)
(Solid RED & GREEN)
(Solid RED)
(Solid RED)
(Solid RED & GREEN)
(Solid RED)
(Solid RED)
LCD screen display instructions
1. When charging, the LCD displays "IN", and the battery percentage value
flashes (1 flash per second). When the battery is charged to 100%, it stops
flashing and stops charging; after 10 seconds, the LCD display is turned off
and enters the sleep state.
2. When discharging output, the LCD displays "OUT" and the current
percentage of power of the product is displayed at the same time.
3. The USB port discharges output corresponds to displaying "5V/ 2.4A" or
"QC 3.0" characters.
4. When the TYPE-C port discharges output, the character "5V/3.0A" is
displayed.
5. When wireless charging is working: the " " symbol shows the current
working status (" " flashes quickly when the wireless charging is
abnormal).
6. In the working state, the discharge of jump start port can normally
indicate the electric quantity.
7. When no load or light load is connected, 30±5S after the LED screen
goes out and enters the sleep mode.
8. When the battery temperature is abnormal, the " " symbol flashes.
1 2 3 4
Model
Capacity
Dimension
Input/Output
Output 1
Output 2
Wireless Output
Start Current
Peak Current
Lifespan
Operating Temperature
Power button
Jump start port
Type-C input/output
Wireless charging
LCD screen
LED light / SOS / strobe
USB output Jumper Cable
Charging CableWall Charger
Zipper Carry Case Car Charger
Color Box Jump Starter
User Manual
What’s in the box ?
5V/3A
1. Turn on the product
2. Connect the product to your device via charging cable.
5V/3A
How to use wireless charging ?
Press the "Power " button to turn on the wireless
feature, the would be solid on.
56789
You can go ahead and place your phone over the
wireless charger pad.
HFT-160-4S
59.2Wh
198 × 92 × 40 mm
5V/3A
5V/2.4A
5V/3A; 9V/2A; 12V/1.5A
10W
1000A
2000A
1000 times
-10℃~50℃
Instructions d'affichage de l'écran LCD
1. Lors de la charge, l'écran LCD affiche "IN" et la valeur du pourcentage de
la batterie clignote (1 flash par seconde). Lorsque la batterie est chargée à
100 %, elle arrête de clignoter et arrête de se charger ; après 10 secondes,
l'écran LCD s'éteint et passe en mode veille.
2. Lors de la décharge de la sortie, l'écran LCD affiche "OUT" et le
pourcentage actuel de puissance du produit s'affiche en même temps.
3. La sortie de décharge du port USB correspond à l'affichage des
caractères "5VI 2.4A" ou "QC 3.0".
4. Lorsque le port TYPE-C décharge la sortie, le caractère "5V/3.0A"
s'affiche.
5. Lorsque la charge sans fil fonctionne : le symbole " " indique l'état
de fonctionnement actuel ( " " clignote rapidement lorsque la charge
sans fil est anormale).
6. Dans l'état de fonctionnement, la décharge du port de démarrage rapide
peut normalement indiquer la quantité électrique.
7. Lorsqu'aucune charge ou charge légère n'est connectée, 30 + 5S après
que l'écran LED s'éteint et passe en mode veille.
8. Lorsque la température de la batterie est anormale, le symbole " "
clignote.
1 2 3 4
¡
¡
¡
¡
5V/3A
Comment utiliser la recharge sans fil ?
Appuyez sur le bouton "Power" pour activer la fonction
sans fil, le " "sera allumé.
56789
Vous pouvez continuer et placer votre téléphone sur le
chargeur sans fil.
Modèle
Capacité
Dimension
Entrée sortie
Sortie 1
Sortie 2
Sortie sans fil
Courant de démarrage
Courant de crête
Durée de vie
Température de fonctionnement
Bouton d'alimentation
Port de démarrage rapide
Entrée/sortie de type C
Chargement sans fil
Écran ACL
Lumière LED / SOS / stroboscope
Sortie USB
¡
¢
£
¤
¥
¢
HFT-160-4S
59.2Wh
198 × 92 × 40 mm
5V/3A
5V/2.4A
5V/3A; 9V/2A; 12V/1.5A
10W
1000A
2000A
1000 fois
-10℃~50℃
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in 3 residential installation.This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference
will not occur in a determined particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect
the equipment into an outlet on a circuit different from that to which the receiver
is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
FCC STATEMENT
-
1
-
2
-
3
-
4
-
5
dans d''autres langues
- English: Boltpower HFT160 User manual
Autres documents
-
Schumacher SL1452 Jump Starter/Power Pack Le manuel du propriétaire
-
-
Schumacher SL1317 1000 Peak Amp Lithium Ion Jump Starter/ Power Pack Le manuel du propriétaire
-
-
-
-
-
-