Questions, problems, missing parts? Contact technical support department at
657-341-0362, 9:00 a.m. - 5 p.m., PST, Monday - Friday or visit us online at
www.lifesmartcomfort.com
Please have your model and serial number ready
1REV1-061121
ATTACH YOUR RECEIPT HERE
Purchase Date ____________Serial Number (located on back of unit) __________________
LIFE SMART® is a registered trademark of
Supply Chain Sources LLC., All Rights Reserved.
INFRARED QUARTZ
HEATER
LIFESMART MODEL: HT1189
MVH-2000
2
TABLE OF CONTENTS
Package Contents ...............................................................3
Safety Information ..............................................................4
Frequently Asked Questions ......................................................6
Preparation ....................................................................8
Troubleshooting ................................................................8
Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control ................................................................10
Operating Instructions ..........................................................11
Care and Maintenance ..........................................................13
One-Year Limited Warranty ......................................................14
Replacement Parts List .........................................................15
3
PACKAGE CONTENTS
Front View Rear View
PART DESCRIPTION QUANTITY
A Infrared Heater 1
B Remote Control 1
C Control Panel (preassembled to Infrared Heater (A)) 1
D Filter Cover (preassembled to Infrared Heater (A)) 1
E Temperature Sensor (preassembled to Infrared Heater (A)) 1
F Master Power Switch (preassembled to Infrared Heater (A)) 1
G Caster Wheels (preassembled to Infrared Heater (A)) 4
4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO. When using electrical appli-
ances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury
to persons, including the following:
• This heater must be plugged into a 120 V, 15 amp (or more) circuit of its own. Do not plug anything
else into the same circuit. If unsure if your home meets this specification, consult a certified elec-
trician prior to use. Risk of fire, overheating, malfunction, property damage, injury, or even death
may result if not adhered to!
• Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to extension cords,
surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same
outlet. Risk of fire, overheating, malfunction, property damage, injury, or even death may result
if not adhered to!
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles
(certain models) or wheels to move this heater.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at
least 3 ft. (0.9 m) from the front of the heater and keep them away from the sides and rear of the
heater.
• Extreme caution is necessary when any heater is used by or near children, invalids, pets, or when
the heater is left operating unattended.
• Always unplug the heater when not in use.
• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been
dropped, or damaged in any manner. Contact the manufacturer for resolution options.
• Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind, or extreme tem-
peratures may cause the heater to become a safety hazard.
• This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations, nor
any locations that use GFCI outlets.
• Never place the heater where it may fall into a bathtub or other water receptacles.
• Do not run the cord under carpet. Do not cover the cord with throw rugs, runners, or similar cover-
ings. Arrange the cord away from traffic areas and where it will not be tripped over.
• The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15 amp
rating on that individual circuit.
• To disconnect the heater, first turn the power button to the OFF position and then remove the plug
from the wall outlet.
• Do not allow foreign objects to enter or block any ventilation or exhaust opening as this may cause
electric shock, fire, or damage the heater.
• Allow at least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum
heat, air, and ventilation flow.
• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint,
or flammable liquids are used or stored, nor use flammable solvents to clean the heater. Keep the
heater dry at all times.
• Use this heater only as described in this manual. Any other use not recommended by the manufac-
turer may cause fire, electric shock, or injury to persons.
• Do not use abrasive solvents to clean the heater as it may cause damage to the finish or casing.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a bed, where opening may become blocked.
• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or
relocatable power tap (outlet/power strip).
SAVE THESE INSTRUCTIONS
5
SAFETY INFORMATION
Child Safety Lock Feature
Press and hold the child lock button located on the control panel for 5 seconds or
remote control for 3 seconds. Locking is confirmed when a buzzer rings and the
control panel displays “CL”. When locked, the control panel and remote control (if
provided) will not function.
To unlock the control panel or remote (if provided), repeat this procedure. Unlock-
ing is confirmed when a buzzer rings and the lock indication disappears.
Tip-Over Safety Feature
This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch
will automatically shut the heater off. Once the heater is restored to an upright position, the heater will
reset. To continue operation, turn on the heater using the control panel or supplied remote control (if
provided) on the heater.
Overheat Safety Feature
This heater is equipped with an overheat safety feature. When the internal components of the heater
reach a certain temperature that could cause overheating or possible fire, the heater will automatically
shut off. If the unit has been overheated, you will need to unplug the unit from the wall and replug it in
to use the heater again.
WARNING: This heater has a voltage rating
of 120 volts. The cord has a three-blade, ground-
ing-type plug. An adapter is available for connect-
ing three-blade grounding-type plugs to two-slot
receptacles. The grounding lug extending from
the adapter must be connected to a permanent
ground such as a properly grounded outlet box.
The adapter should not be used if a three-slot
grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDED PLUG.
Grounding Pin
Grounding Means Grounding Pin
Metal Screw
Cover of Grounded
Outlet Box
WARNING: It is normal for the power cord to feel warm to the touch. However, a loose fit between
the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a
different outlet. Contact a qualified electrician to inspect the original outlet for damage.
Specifications
Voltage Rating 120 V (60 Hz)
Power Consumption 750 W/1,500 W
Unit Size 12.9 in. (W) x 20.1 in. (D) x 17.4 in. (H)
Unit Weight 28.50 lbs.
6
INFORMATIONS SUR LA SÉCURITÉ
Veuillez lire et comprendre ce manuel entier avant d’essayer d’assembler, d’utiliser ou d’installer l’appareil.
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT: RISQUE POTENTIEL D’ÉLECTROCUTION SI LES CONSIGNES DE SÉCURITÉ NE
SONT PAS RESPECTÉES. Lors de l’utilisation d’appareils électriques, les précautions de base doivent tou-
jours être suivies pour réduire le risque d’électrocution, d’incendie et de blessure corporelle, notamment :
• Ce radiateur doit être branché sur un circuit 120 V, 15 A (ou plus) qui lui est propre. Ne branchez rien d’autre
sur le même circuit. Si vous n’êtes pas sûr(e) que votre habitation réponde à cette spécification, consultez un
électricien certifié avant toute utilisation. Si cette spécification n’est pas remplie, il y a risque d’incendie,
de surchauffe, de mauvais fonctionnement, de dommages matériels, de blessures, voire même la mort.
• Branchez l’appareil uniquement dans une prise à 3 trous correctement mise à la terre. Ne branchez
pas le radiateur dans des rallonges électriques, des limiteurs de surtension, des minuteries, des
coupe-circuits directs ou dans une prise où d’autres appareils sont également branchés. Si cette
spécification n’est pas remplie, il y a risque d’incendie, de surchauffe, de mauvais fonctionnement,
de dommages matériels, de blessures, voire même la mort.
• Ce radiateur est chaud quand il est utilisé. Pour éviter les brûlures, ne laissez pas la peau nue toucher des
surfaces chaudes. Utilisez les poignées (sur certains modèles) ou les roues pour déplacer ce radiateur.
• Maintenez les matériaux combustibles, par exemple les meubles, les oreillers, la literie, les papiers,
les vêtements et les rideaux au moins éloignés de 0,9 m (3 pi) de la façade du radiateur et main-
tenez-les à l’écart des flancs et de l’arrière du radiateur.
• Il faut prendre des précautions extrêmes quand un radiateur est utilisé à côté ou près d’enfants,
de personnes handicapées, d’animaux familiers ou quand le radiateur est utilisé sans surveillance.
• Débranchez toujours le radiateur quand il n’est pas utilisé.
• N’utilisez pas un radiateur ayant un cordon ou une prise endommagés ou s’il fonctionne mal, s’il est
tombé ou s’il a été endommagé d’une manière ou d’une autre. Communiquez avec le fabricant pour
savoir comment remédier à ces problèmes.
• Ne pas utiliser en plein air. L’exposition du radiateur aux éléments naturels, par exemple la pluie, la
neige, le soleil, le vent ou les températures extrêmes, peut rendre son utilisation dangereuse.
• Ce radiateur n’est pas destiné à être utilisé dans les salles de bain, les buanderies et autres lieux
intérieurs similaires, ni dans les endroits ou des prises à disjoncteur de fuite de terre sont utilisées.
• Ne placez jamais le radiateur dans un endroit d’où il pourrait tomber dans une baignoire ou dans
d’autres réceptacles contenant de l’eau.
• Ne faites pas courir le cordon sous un tapis. Ne recouvrez pas le cordon d’une carpette, d’un tapis
d’escalier ou d’éléments couvrants similaires. Disposez le cordon à l’écart des zones de circulation
et des endroits où l’on pourrait trébucher dessus.
• Le radiateur doit être branché dans une prise murale ayant son propre circuit d’une intensité nom-
inale minimale de 15 A.
• Pour débrancher le radiateur, tournez d’abord le bouton de mise sous tension sur la position « OFF
» (ARRÊT) et retirez ensuite la fiche de la prise murale.
• Ne laissez pas d’objets étrangers pénétrer ou bloquer les ouvertures de ventilation ou d’échappe-
ment, car ceci peut être à l’origine de décharges électriques, d’incendie ou risque d’endommager
le radiateur.
• Laissez un dégagement libre de toute obstruction d’au moins 0,9 m (3 pi) devant et à l’arrière du
radiateur pour permettre à la chaleur, à l’air et à la ventilation de circuler librement.
• L’intérieur du radiateur contient des pièces chaudes pouvant produire des décharges électrosta-
tiques ou des étincelles. Ne l’utilisez pas dans des endroits où de l’essence, de la peinture ou des
liquides inflammables sont utilisés ou stockés, et n’utilisez pas de solvants inflammables pour net-
toyer le radiateur. Maintenez en permanence le radiateur sec.
• Utilisez ce radiateur uniquement comme cela est décrit dans ce manuel. Toute autre utilisation non recom-
mandée par le fabricant peut causer un incendie, des décharges électriques ou blesser des personnes.
• N’utilisez pas de solvants abrasifs pour nettoyer le radiateur, car ils pourraient endommager le
revêtement ou l’enveloppe.
• Pour éviter un incendie, ne pas bloquer les entrées et sorties d’air de quelque manière. Ne pas uti-
liser sur des surfaces molles, comme un lit, où l’ouverture peut être bloqué.
• Toujours brancher chauffe directement dans une prise murale / réceptacle. Ne jamais utiliser une
rallonge ou robinet d’alimentation relocalisable (sortie de bande / de puissance).
CONSERVER CES INSTRUCTIONS
7
INFORMATION DE SÉCURITÉ
Dispositif de sécurité et de verrouillage pour enfant
Appuyez pendant 5 secondes sur le bouton de verrouillage pour enfant situé sur
le tableau de commande. Le verrouillage est confirmé quand un vibreur se dé-
clenche et que le tableau de commande affiche « CL ». Quand le radiateur est
verrouillé, le tableau de commande et la télécommande ne fonctionnent pas
Pour déverrouiller le tableau de commande et la télécommande, répétez cette
procédure. Le déverrouillage est confirmé quand un vibreur se déclenche et que
« CL » cesse de s’afficher.
Dispositif de sécurité après-basculement
Ce radiateur est équipé d’un dispositif de sécurité après-basculement. Une fois que le radiateur a bas-
culé, un commutateur interne l’arrête automatiquement. Une fois que le radiateur retrouve sa position
debout, il peut être remis en marche. Pour poursuivre l’opération, allumez le radiateur en utilisant la
télécommande fournie ou le tableau de commande sur le radiateur.
Dispositif de sécurité anti-surchauffe
Ce radiateur est équipé d’un dispositif de sécurité anti-surchauffe. Quand les composants internes
du radiateur atteignent une certaine température pouvant causer une surchauffe ou potentiellement
un incendie, le radiateur s’éteint automatiquement. Si l’appareil a surchauffé, vous aurez besoin de
débrancher l’appareil du mur et le rebrancher pour utiliser le chauffe à nouveau.
AVERTISSEMENT: Ce radiateur à une tension
nominale de 120 V. Le cordon est équipé d’une
fiche à trois lames reliée à la terre. Un adapta-
teur est disponible pour brancher les fiches à trois
lames reliées à la terre aux prises à deux trous.
La patte de mise à la terre ressortant de l’adapta-
teur doit être connectée de façon permanente à la
terre, par exemple à une boîte à prises correcte-
ment mise à la terre. L’adaptateur ne doit pas être
utilisé si une prise à trois trous mise à la terre est
disponible.
NE PAS CONTOURNER L’OBJECTIF DE SÉCURITÉ
DE LA FICHE MISE À LA TERRE.
Grounding Pin
Grounding Means Grounding Pin
Metal Screw
Cover of Grounded
Outlet Box
AVERTISSEMENT: Il est normal que le cordon d’alimentation soit chaud au toucher. Toutefois, une
fiche mal enfoncée dans la prise peut entraîner la surchauffe de la fiche. Si cela se produit, essayer
d’insérer la fiche dans une prise différente. Communiquer avec un électricien qualifié pour qu’il vérifie
si la prise d’origine est endommagée.
Spécifications
Voltage 120 V (60 Hz)
Consommation d’énergie 750 W/1,500 W
Taille d’unité 12.9 in. (W) x 20.1 in. (D) x 17.4 in. (H)
Unité de poids 28.50 lbs.
8
FREQUENTLY ASKED QUESTIONS
Please review these frequently asked questions on the next few pages prior to using your heater.
Q. My heater emits a strange odor when I first open the box and when I turn the heater on for the first
time. Why is this happening?
A. This is normal. This heater is treated with a special heat safe/resistant coating. This odor will some-
times be present when the box is opened. When the coating is exposed to heat, it produces this par-
ticular odor during the first few hours of operation. This will dissipate after the break-in period. If you
are sensitive to odors, you may want to pre-burn the unit in a garage with the door open until the initial
odor dissipates.
Q. If my heater runs on its max wattage setting, how many BTUs is that?
A. This heater is intended to be used as supplemental heat in areas most needed. It may take several
minutes to several hours to heat your area, depending on various factors. The below chart provides BTU
translations for different wattages.
WATTAGE BTUS
1,500 5,118
1,000 3,412
750 2,559
500 1,706
Q. Can the heating elements be replaced?
A. Replacement heating elements can be obtained from the manufacturer. All parts may be purchased
through the manufacturer if your product is out of warranty. If you feel that the elements are definitely
faulty right out of the box, contact Customer Support. A representative can then direct you to the next
step.
Q. Once I plug the unit in and turn it on, how long will it take to heat my room?
A. The heating process in the heater begins immediately upon powering on and setting the desired
temperature above the ambient temperature. A noticeable change in the ambient temperature of the
room will vary due to variables such as the location of the heater (in the home), floor plan and size of
the room, how well the room is insulated, how many doors/windows, how much bare concrete (acts as
a heat sink with any type of heating), the opening and closing of an exterior door, long hallways, high
ceilings, etc. Customers with smaller rooms experience quick heat changes. Rooms with larger and
open floor plans can expect up to 24 hours to completely heat up.
Q. I do not have a grounded outlet. Can I use adapters, a 2-prong power strip, or remove the ground
prong from the cord?
A. NO! If you do not have a grounded outlet, contact a certified electrician for advice. Removing or al-
tering any part of the heater’s original design or intent (including the power cord) will void the warranty
and make you liable for any unexpected or hazardous results.
Q. My Heater has an ECO setting? How does this setting work?
A. The ECO mode on your heater is a program that attempts to keep the temperature strictly at a
“warm” 68° F (20°C). This also helps with efficiency, as it is programmed to 1) Increase the power
to the unit’s maximum wattage if the temperature drops below 64.4°F (18°C) 2) Gradually reduce the
wattage used as it approaches 66.2° (19°C) F and 3) Stop heating when 68° F (20°C) is achieved. This
is considered an Economical function, since in the ECO setting, the heater is almost never running at
the maximum watts.
9
FREQUENTLY ASKED QUESTIONS
Q. The temperature on my heater does not match the temperature display on my wall, or external
thermostat. Why?
A. This is completely normal. The temperature display on your heater may vary from the temperature
display on another thermostat (like the one mounted to your wall or a purchased external thermostat).
This is because the temperature sensor on the heater reads the temperature directly around the heater.
With the heater near the cold floor (and heat rising), any readings on elevated or external thermostats
will differ in readings on the heater. The best way to operate your heater is to set the unit on High and
dial up to a temperature that feels comfortable to you. Then, leave it at that temperature, regardless of
the mismatch. The heater will cycle off when the set temperature is met or exceeded slightly.
Q. Can I use more than one heater at a time? Can I use the heater and another appliance at the same
time?
A. Yes, but make sure they are not plugged into the same circuit. Each heater requires its own mini-
mum 15-amp circuit with no other items plugged into that circuit or outlet. This is because heaters are
considered appliances and draw out high amperage. If you are unsure your circuit meets these require-
ments, verify with a certified electrician.
WARNING: Risk of fire, damage to property, or injury may result if requirements are not met.
Q. Why does my heater’s fan continue to run after the set temperature is reached or the power is turned
off?
A. This is normal. The heater’s fan will continue to run even after the heater automatically cycles down.
The fan continues to run so that every last bit of heat is blown out of the heat chamber while allowing
the unit to continue filtering your air. Once the internal box/components cool completely, the fan should
then shut off on its own. In this case, allow a few minutes after the heat cycles off (with power on). The
fan will shut off faster when the power is turned off.
Q. My heater’s display shows my ambient temperature to be in the 20s when I know it is warmer than
that. Why?
A. The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is definitely
heating but shows it is in the 20s you probably have the setting to read your temperature in Celsius
rather than Fahrenheit.
Q. My heater’s power cord gets warm. My cord is showing signs of heat or melting at the outlet. Is
this normal?
A. A warm power cord is normal. These power cords are rated safe for up to 105°C/ 221°F by the UL,
CSA, or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of the
wall outlet, it may be due to loose or worn wall contacts (or arcing). Please stop using the heater imme-
diately, contact warranty support for a replacement power cord, and have a certified electrician replace
the wall outlet as soon as possible.
10
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120 V, 60 Hz power outlet and turn on
the power switch on the rear of the unit. Only operate heater in upright position.
Insert two AAA batteries into the remote control before using (batteries not included).
Please note that infrared heaters do not heat like a traditional space heater. You should not expect
infrared heaters to blow hot air like a traditional space heater. Infrared heaters heat objects not air.
Infrared heaters are intended to supplement an already heated, insulated room. Square footage specifi-
cations assume a single enclosed room not an entire home. Infrared heaters do not heat through walls,
floors, and are not intended to replace a main heat source. Infrared heat can take at least 24 hours to
warm a room but operate much more efficiently to maintain the desired temperature. Infrared heaters
will not work well in uninsulated unheated spaces like screened in porches, RV’s, garages, unheated
basements, etc.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The heater does not
turn on.
1. The power cord is not plugged in.
2. The electricity at the main fuse box
is not working.
3. The battery in the remote control
is dead.
4. The thermostat on the heater is
set lower than the room tempera-
ture.
1. Plug the power cord into an elec-
trical outlet.
2. Check the electricity at the main
fuse box.
3. Replace the batteries in the remote
control.
4. Increase the thermostat tempera-
ture on the heater for a higher heat
setting.
The heater displays
an error code “E1”
1. The heater has overheated.
2. Insufficient power to the unit
3. The air filter is clogged.
4. Insufficient air flow to the heater.
1. Unplug the heater from the wall,
wait a few seconds then plug the
power cord back in.
2. Make sure the unit is plugged into
a dedicated 3-prong outlet, with no
extension cords or surge protec-
tors.
3. Clean the airfilter located on the
back of the unit. see page 13.
4. Move the unit at least 3ft from the
wall.
The heater displays
an error code “E2”
1. Temperature sensor not function-
ing properly.
1. Please contact technical support.
11
CONTROL PANEL
21 3
78910111213
14
15
16
4
5
6
đ
đ
̧
̧
PART NAME DESCRIPTION
1 Fan Indicator Light Indicates when the Fan is on
2 Timer Indicator Light Indicates when the timer function is active
3 Digital Display Readout of the set room temperature or timer value
4 Celsius Indicator Light Indicates that the temperature is being displayed in Celsius
5 Fahrenheit Indicator Light Indicates that the temperature is being displayed in Fahrenheit
6 Power Indicator Light Indicates when the unit is receiving power from the wall outlet
7 Power Switch Button Powers the heater ON or OFF
8 Ambient Temp. Button Indicates ambient temp / hold to toggle between °C/°F
9 Temp-Down Button Decreases the set temperature
10 Temp-Up Button Increases the set temperature
11 Timer Button Engages the on/off timer function
12 Heater Mode Button Toggles between Hi / Low / Eco Modes
13 Safety Lock Button Hold to Lock / Unlock heater’s control panel
14 Energy Saving Indicator Indicates when energy-saving mode is on
15 High Heat Indicator Indicates when High Heat mode is on
16 Low Heat Indicator Indicates when Low Heat mode is on
12
REMOTE CONTROL
1
2
3
4
5
6
PART NAME DESCRIPTION
1 Temp Up Button Increases the set temperature value
2 Mode Button Toggles between the three heat modes available
3 Temp Down Button Decreases the set temperature value
4 Power Button Powers the heater on or off
5 Ambient/Lock Button Short press: Shows Ambient temperature.
Long press for 3 seconds to activate lock function.
6 Timer Button Engages the on/off timer
13
OPERATING INSTRUCTIONS
1. Turn the heater on or off by pressing the Power
button on the control panel (C) or by pressing
the ON/OFF button on the remote control (B).
Once the power is off, heating elements will
stop working first. The fan will continue work-
ing for up to 90 seconds to dispense residual
heat inside the heater. This is a normal func-
tion.
1
CB
2. Select a heat setting by pressing the HEAT
button on either the control panel (C) or the
remote control (B) to toggle between the three
heat settings.
Power for heat-up mode is 1,500 W; heat-down
is 750 W. ECO mode is an Economic Energy
Saving Function. When ECO mode is chosen,
the heater will operate to maintain a constant
warm 68°F
2
C B
HIGH LO
WE
CO
3. Set the temperature by pressing the arrows on
the control panel (C) or the remote control (B).
You can set the temperature on the heater
anywhere between 50°F and 90°F or between
10°C and 32°C. Once you have chosen the de-
sired temperature, the heater will remain on
until the room temperature increases to the
temperature on the digital display. The heat-
er will cycle on and off to maintain the desired
room temperature.
To view the ambient temperature short press
the ambient temperature button on the control
panel (C) or remote control (B).
Note: To switch between Fahrenheit and
Celsius, press and hold the ambient
temperature button on the control panel
(C) for 5 seconds.
Note: To engage the child lock on the remote (B),
press and hold for 3 seconds. Deactivate
the lock by repeating these steps.
3
C
B
OR
CB
14
OPERATING INSTRUCTIONS
4. To set the timer power off, start the unit and
press the Timer button on the control panel (C)
or remote control (B).
Note: The timer-power-off function can only be
set when the heater is in power-on mode.
The digital display on the control panel (C)
changes from the set temperature readout
to a time value for the timer. Press the Timer
button repeatedly to change the number val-
ue between a range of 0 to 12 hours (in 1-hour
intervals).
The Timer light turns on when the timer is set.
4
C B
TIMER
TIMER
5. To set the timer power on, while powering off
the unit press the Timer button on the control
panel (C).
Note: The timer-power-on function can only be
set when the heater is in power-off mode.
The digital display on the control panel (C) will
indicate time value for the timer. Press the
Timer button repeatedly to change the num-
ber value between a range of 0 to 12 hours (in
1-hour intervals).
The Timer light turns on when the timer is set.
5
C B
TIMER
TIMER
6. To replace the batteries, remove the battery
cover (1) from the remote (B) by applying
pressure to the battery cover (1) and sliding
it away from the remote (B). Insert two AAA
batteries (not included) (2) and close the
remote by placing the battery cover (1) back on
the remote (B).
Note: Do not mix old and new batteries. Do not
mix alkaline, standard (carbon-zinc), or
rechargeable (nicad, ni-mh, etc) batter-
ies.
6
B
1 2
15
CARE AND MAINTENANCE
WARNING: Before performing any maintenance task, turn off the power switch in the rear of the
unit, unplug the unit, and allow it to cool completely.
1. To keep the heater clean, clean the outer shell with a soft, damp cloth. Use a mild detergent if
necessary. After cleaning, dry the unit with a soft cloth.
CAUTION: DO NOT let liquid enter the heater.
2. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the
heater. This may cause damage or deterioration to the surface of the heater.
3. DO NOT immerse the heater in water.
4. Wait until the unit is completely dry before use.
5. If you will not be using the heater for a while, take the batteries out of the remote control and
store for future use.
6. Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the
original packaging to repack the unit.
CLEANING THE AIR FILTER
1. Clean the air filter (2) after three months or if it appears to be blocking airflow. With the heater
unplugged, remove the two filter screws (1) as illustrated below. Clean all parts of the filter as-
sembly and allow parts to completely dry.
2. Reassemble and reinstall the filter (2).
WARNING: Do not use the heater without the filter assembly in place.
1
2
1
16
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this heater against defects in materials and workmanship on functional
parts, for a period of 1 year from the original date of purchase. Your sales receipt showing the date of
purchase of the product is your proof of purchase. Keep it in a safe place for future reference. This war-
ranty is subject to personal use only, commercial or rental applications will not be covered.
This product is made with the highest quality materials and is warranted to be free from defects in ma-
terials and workmanship at the time of purchase. This limited warranty applies to products manufac-
tured or distributed by the manufacturer, are delivered in the continental United States or Canada and
extends to the original purchaser, or gift recipient. This warranty becomes valid at the time of purchase
and terminates either by the specified time frame listed above and/or owner transfer. Any refunds or
monetary compensations must be claimed through the place of purchase (retailer), and not through
the manufacturer. Any extended warranties (warranties that cover above and beyond this manufacturer
warranty) that are sold through a retailer or third party, are not directly correlated with this products’
limited warranty, and may be redirected to said retailer or third party for coverage.
This warranty extends through the manufacturer of the product, and covers functional parts only. Cos-
metics are not covered, unless unequivocally determined it is a workmanship defect. Shipping damage
should be addressed with the shipping company, retailer, or place of purchase, not the manufacturer
unless the manufacturer was the direct shipper.
The manufacturer’s sole obligation under this warranty shall be limited to furnishing the original pur-
chaser replacement parts for units deemed repairable by the supplier’s warranty department. The
purchaser is responsible for insuring any parts shipped or returned, if desired. The purchaser is re-
sponsible to prepay any shipping charges (both ways) including, but not limited to taxes and duties. All
exchanged parts and products replaced under this warranty will become the property of manufacturer.
The manufacturer reserves the right to change manufacturers of replacement parts or products for
use, in order to cover any existing warranty.
The purchaser may be asked to provide the supplier with proof of purchase documents (including the
date of purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase doc-
uments will be just cause to VOID this limited warranty. Products, in which the serial number has been
defaced or removed are not eligible for warranty coverage.
This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or
repairs, alteration by non-manufacturer authorized personnel, inappropriate installations, or any case
beyond the control of the manufacturer. Examples of warranty invalidation may also include, but are
not limited to:
• Use of lacquer or paints in (and around) the heaters
• Heater placed on non-approved surfaces
• Electrical requirement deficiencies (15-20 amp dedicated outlet)
• Use on extension cords/timers/surge protectors/GFCI
• Outdoor applications
• Normal wear/tear/weathering
• Pet/consumer accidents
• Purchases from dealers unauthorized by the manufacturer (Authorization in writing)
The manufacturer shall not be liable for any loss due to use (or misuse) of the heater or other incidental
or consequential costs, expense or damages without irrefutable foundations. Under no circumstances
shall the manufacturer or any of its representatives be held liable for injury to any person or damage
to any property, however arising. Any implied warranty shall have duration equal of the applicable war-
ranty stated above. Specifications are subject to change without notice or obligation.
This limited warranty gives the original purchaser specific legal rights. Other rights may vary from state
to state.
17
REPLACEMENT PARTS LIST
For replacement parts, call our technical support department at 657-341-0362, 9:00 a.m. - 5 p.m.,
PST, Monday - Friday
PART DESCRIPTION PART #
A Control panel COPA-H2018
BFan FAN-DC
C Power board POBO-H2018
D Limit switch LIMITSW130
E Infrared tube QUAR-R185
F Thermostat Wire SENSOR
G Master Power Switch MAINSW-S
H Remote control REMO-H2016
A
D
F
E
B
H
G
C
18
Printed in China
LIFE SMART® is a registered trademark of
Supply Chain Sources LLC., All Rights Reserved.
PLEASE REMEMBER TO REGISTER YOUR WARRANTY:
web: www.lifesmartcomfort.com
email: cs@scsources.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
dans d''autres langues
- English: Lifesmart HT1189 User manual
Documents connexes
Autres documents
-
Life Smart Infrared Quartz Heater HT1270 Manuel utilisateur
-
Life Smart LS1002HH13 Le manuel du propriétaire
-
Comfort Glow QTH7100 Le manuel du propriétaire
-
World Marketing of America QTH6000 Le manuel du propriétaire
-
-
-
-
