Sommer Pro+ Intelligent Garage Door Guide d'installation
- Catégorie
- Porte de garage
- Taper
- Guide d'installation
26
Fig. 28
NOTE
Do not push the door to the mechanical stop. This
is because the opener will pull the door against
the mechanical stop. This will apply tension to the
door and it may be damaged.
A clearance of 1.18" (30 mm) is required.
INFORMATION
Alternatively, the limit stop can be pushed under
the chain and clamped into the rail later.
28. Tighten the screw on the limit stop with a phillips
screwdriver without changing its position.
Check the door OPEN end position:
Open the door fully for this. The carriage moves to the
door OPEN position on the limit stop until a click noise
is heard.
The door OPEN end position is set.
“clic”
¹⁄
¹⁄
Fig. 29 Fig. 30
NOTE
In case of an emergency release, the door may
independently open or close itself due to a broken
spring or incorrect setting of the weight balancing.
The opener could be damaged or destroyed.
INFORMATION
It can be locked and released in any door posi-
tion.
29. Move door to center position.
The carriage moves with it.
30. Pull the emergency release handle.
Carriage is locked.
The door can only be moved by the opener.
24. Attach the curved door arm (1) to the door bracket (2).
Guide the bolt, (3) through the hole in the door brack-
et and in the curved door arm and secure with the lock-
ing c-clip (4).
25. Attach the door arm (5) to the carriage (6). The open
side of the door arm must be facing towards the ceiling.
Guide the bolt (7) through the holes in the carriage and
the door arm. Secure with the locking c-clip (8).
1/2"
Fig. 26
26. Slide the curved door arm (1) into the door arm (2)
and secure with two bolts 3/8" (3) and two self-locking
nuts 3/8" (4).
Tighten the nuts using a 1/2" open-end wrench. While
tightening, hold the screws in place using a second
1/2" open-end wrench. Basic position of the screw
arrangement, see graphic. The length of the door arm
can be adjusted if necessary.
Fig. 27
NOTE
The door must not rub on the opener or rails. This
could damage the opener or rails.
7KHRSHQHUPXVWEHRႇVHW
27. Open the door completely by hand.
The limit stop automatically moves with the carriage.
5. Installation
27
NOTE
To prevent damage to the opener, do not connect
the wall control unit to the power supply until
installation is complete.
INFORMATION
The power cable is approx. 5,7' (1.74 m) long.
INFORMATION
The power cord that has been provided must not
be shortened or extended.
All devices to be connected externally must have
safe isolation of the contacts from the mains volt-
age supply in accordance with IEC 60364-4-41.
Wiring for external devices must be installed in ac-
cordance with IEC 60364-4-41.
All electrical wiring, including the control cable,
PXVWEH¿UPO\VHFXUHGWRSUHYHQWGLVSODFHPHQW
5'
(>1,53 m)
5'
(>1,53 m)
Fig. 1
INFORMATION
The drilling depth must be considered with re-
spect to the ceiling and wall thickness, particularly
with prefabricated garages. It may be necessary
to reduce the hole depth.
Only use permissible mounting materials appro-
priate for the supporting surface.
1. Choose a suitable location for the wall control unit
close to an existing power outlet.
The maximum length of the control cable is 16.4' (5 m),
and it must not be extended.
Note that the distance between the wall control unit
and the power outlet must not exceed 5,7' (1,74 m).
The membrane keypad of the wall control unit must be
installed at a height of at least 5' (>1.53 m).
3.
1.2.
Fig. 2 Fig. 3
WARNING
Danger due to projecting parts!
Door wings or other parts must not project into
roads or public footpaths. This also applies
while the door is moving.
This may cause serious injury or death to per-
sons or animals.
`Parts must not project into roads or public
footpaths.
The door opener is completely assembled.
5.7 Installing the wall control unit
In particular, follow the basic safety instructions listed
below.
DANGER
Danger due to electric current!
Contact with live parts may result in electric
FXUUHQWÀRZLQJWKURXJKWKHERG\(OHFWULF
shock, burns or death will result.
`All work on electrical components must be
carried out by a trained electrician.
`Before inserting the mains power plug for
WKH¿UVWWLPHHQVXUHWKDWWKHYROWDJHRIWKH
power source matches the voltage listed on
the opener type plate.
`Do not connect the power supply until instal-
lation is complete.
`Disconnect the mains plug before working on
the opener.
`If a battery pack is connected, disconnect it
from the wall control unit.
`Check that the opener is not live.
`Secure the opener against being switched
back on.
WARNING
Danger of crushing and shearing!
The door can be actuated via the wall switch.
If the door moves and there are persons or ani-
mals in the movement area, crushing and shear-
ing injuries may be caused by the mechanism
and safety edges of the door.
`The membrane keypad of the wall control unit
must be mounted within sight of the door.
`The membrane keypad of the wall control unit
must be mounted at a height of at least 5 feet
to ensure that children cannot operate the wall
station.
`Children must not be allowed to operate the
wall station/the opener.
`Always keep the moving door in sight.
`Persons or animals must not be in the range of
movement of the door.
`Never put your hand near the door or moving
parts when it is moving. In particular, do not
reach into the moving push arm.
`Do not reach into the ceiling mounting unit
when the carriage is running along the rail.
`Do not drive through the door until it has been
fully opened.
5. Installation
28
Feed the control cable into the wall control unit through
the cable inlet.
7. Shorten the control cable to no less than 7'' (174 mm)
in length, uncover the last 2'' (50 mm) and strip the
wires.
gn
rt
Fig. 8 Fig. 9
8. Remove the below strain relief.
Route the control cable in the wall control unit along
the transformer up to the gn/rt terminal.
Secure the control cable with the below strain relief to
prevent displacement.
9. Connect the bu wire of the control cable to the gn
terminal.
Connect the brown wire of the control cable to the rt
terminal.
10. Close the housing in reverse order.
Installation of the wall control unit is complete.
Other connection options such as buttons are described
in chapter "6. Connection and special funtions of the wall
control unit".
NOTE
The control unit cover is connected to the circuit
board of the wall control unit via a connection
cable.
If a battery pack has been installed, it is also
connected to the circuit board. Carefully remove
the control unit cover and unplug the connections.
This prevents damage to the wall control unit.
2. Loosen the screw on the wall unit of the control
unit cover and remove the control unit cover gently
upwards.
3. Unplug the connection cable for the membrane keypad
from the wall control unit.
8,8
''
(224 mm)
2,95
''
(75 mm)
1,6
''
(40 mm)
1,6
''
(40 mm)
1/4
'' (
6 mm)
Fig. 4: Installation example
WARNING
Risk of eye injury!
&KLSVÀ\LQJZKHQGULOOLQJPD\FDXVHVHULRXV
injuries to eyes and hands.
`Wear safety glasses when drilling.
4. Transfer the mounting points to the substructure.
Drill two holes (Ø 1/4" x 1,6" / Ø 6 x 40 mm deep).
Insert the two wall plugs.
Affix the wall control unit with two screws and two
washers, align the unit and firmly tighten the screws.
Press the sealing plugs into the indentation to seal the
housing.
5. Route the control cable of the plug-in unit up to the wall
control unit and secure to prevent displacement.
2''
(50 mm)
7''
(174 mm)
Fig. 6 Fig. 7
6. Lay the control cable along the cable conduit on the
rear side of the wall control unit up to the cable inlet.
5. Installation
29
4. If a battery pack is used, it must also be disconnected,
see Chapter "8.1 Installing and removing battery pack".
5. Remove the control unit cover.
Attaching the control unit cover
1. After working on the wall control unit, replace the con-
trol unit cover in reverse order.
2. Connect the operator to the mains voltage. Check that
the power supply is connected.
The operator is supplied with mains voltage.
6.1 Control unit cover of the wall control
unit
DANGER
Danger due to electric current!
Contact with live parts may result in electric
FXUUHQWÀRZLQJWKURXJKWKHERG\(OHFWULF
shock, burns or death will result.
`All work on electrical components must be
carried out by a trained electrician.
`Disconnect the mains plug before working on
the operator.
`If a battery pack is connected, disconnect it
from the wall control unit.
`Check that the operator is not live.
`Secure the operator against being switched
back on.
WARNING
Danger due to hot surfaces!
After frequent operation, parts of the motor car-
riage or the control unit may become hot. If the
cover is removed and hot parts are touched,
they may cause burns.
`Allow the operator to cool down before
removing the cover.
Removing the light and control unit cover
1. Disconnect the operator from the mains voltage. Check
that the operator is disconnected from the power
supply.
3.
1.2.
Fig. 2 Fig. 3
NOTE
The control unit cover is connected to the cir-
cuit board of the wall control unit via a connec-
tion cable.
If a battery pack has been installed, it is also
connected to the circuit board. Carefully
remove the control unit cover and disconnect
the connections to prevent damage to the wall
control unit.
2. Loosen the screw on the wall unit of the control
unit cover and remove the control unit cover gently
upwards.
3. Unplug the connection cable for the membrane keypad
from the wall control unit.
6. Connection and special funtions of the wall control unit
30
6. Connection and special functions of the wall control unit
6.2 Wall control unit pcb
Signal
COM
GND
+24V
~ 24 V AC
Light
gn rt
+-
SOMMER
Antriebs- u.
FunktechnikGmb
ACCU
GT-G-1
PCxxxxxxx
L` N` NL
KEYPAD
1
4
S1
ON
12345
123 4
11
12
95
6
7
8
10
Fig. wall control unit pcb
Connection options to the wall control unit
1DIP switches 7Terminal, 2-pin
24 V AC transformer secondary side
2ACCU slot 8pcb label
Terminal for battery pack
3Slot, keypad, black 9Terminal, 2-pin
Terminal for the button connector cable of the
pro+ wall control unit chain and rail, 24 V AC
4Slot 10 Light slot, white
Terminal for RELAY, OUTPUT OC terminal for LUMI Strip supplementary lighting
5Terminal, 2-pin 11 Terminal, 4-pin
power supply • safety sensors
• external transformer, 24 V DC, 100 mA
120 V AC, 50/60 Hz
6Terminal, 2-pin 12 Terminal, 2-pin
wall button
transformer primary side
120 V AC, 50/60 Hz
The version can vary depending on the type. This means the use of accessories can vary.
31
pcb section Function/application example
ACCU
BATTERY slot
Terminal for battery pack
KEYPAD
1
Slot, black (only for typ pro+),
5-pin
Terminal for the Keypad connector
cable of the wall control unit
P
AD
1
4
Slot for RELAY, OUTPUT OC
switching capacity
max: 5 A/120 V AC
max: 5 A/24 V DC
L` N` NLTerminal, 2-pin
power supply
120 V AC, 50/60 Hz
L` N` NLTerminal, 2-pin
transformer primary side
120 V AC 50/60 Hz
~ 24 V AC
L` Terminal, 2-pin
24 V AC transformer secondary
side
gn rt
+-
Terminal, 2-pin
chain and rail,
24 V AC
+
24
Light
g
n
+
Light slot, white
slot for LUMI Strip supplementary
lighting
Terminal, 4-pin
2-wire safety sensors
any polarity
Terminal, 4-pin
power output for external de-
vices, 24 V DC, 100 mA
GND and +24 V DC
6. Connection and special functions of the wall control unit
6.3 Connection options to the wall control
unit
WARNING
Danger of crushing and shearing!
The door can be actuated by a button.
Persons who cannot see the door and are in
the range of movement of the mechanism or
the closing edges may be injured by crushing
or shearing.
`Only install the switch in view of the door.
`Do not press the button unless the door is in
view.
`Always keep the moving door in sight.
`Persons or animals must not be in the range
of movement of the door.
WARNING
Danger due to hot surfaces!
After frequent operation, parts of the carriage
or the wall control unit may become hot. If the
cover is removed and hot parts are touched,
they may cause burns.
`Allow the opener to cool before removing the
cover.
NOTE
Never lay the control cable along a power line, as
this could cause interference in the wall control
unit. Note the length of the control cable and
install it correctly.
INFORMATION
The wall control unit detects a short-circuit be-
tween chain and rail and then switches the opener
Rႇ
INFORMATION
&RQWURORUUHJXODWLQJXQLWVLQD¿[HGSRVLWLRQPXVW
be mounted within sight of the door at a height of
at least 5' (1.53 m).
INFORMATION
The power cable is approx. 69'' (1.74 m) long.
INFORMATION
The maximum cable length for connected acces-
sories is 82' (25 m).
32
6. Connection and special functions of the wall control unit
DIP switches on
the wall control
unit ON OFF
5S1
ON
12345
• No function • No function
6.5 Installing the safety sensors
Please observe and comply with all instructions to ensure
a safe installation.
DANGER
Danger due to electric current!
Contact with live parts may result in electric
FXUUHQWÀRZLQJWKURXJKWKHERG\(OHFWULF
shock, burns or death may result.
`Installation, testing and replacement of elec-
trical components may only be carried out by
an electrician.
`The opener must be disconnected from the
power supply before working on the opener.
`If a battery pack is used, it must be discon-
nected.
`Then check that the opener is disconnected
from the power supply.
`Only connect the safety sensors to the
opener terminals in the wall control unit.
`Some local construction ordinances do not
allow an on-wall installation of wires. Please
check with your local building inspector.
STOP
Fig. Test the safety sensors
The safety sensors kit safeguards the door. If the safe-
ty sensors are breached, the door’s closing procedure is
stopped. If the door stops during closing because of the
safety sensors, it subsequently opens completely.
The opener only functions with the connected safety sen-
sors kit. Product contents see "3.5 Product contents for
safety sensor kit".
pcb section Function/application example
Terminal, 2-pin
wall button 2
potential-free
The version can vary depending on the type. This
means the use of accessories can vary.
INFORMATION
If a safety eye is used, it must not be actuated
when starting the programming.
If a safety eye is used as a frame safety eye,
move the door to the center position.
6.4 Setting the DIP switches on the wall
control unit
Special functions can be set up with the DIP switches
on the wall control unit.
All DIP switches are set to OFF by default.
NOTE
Do not use a metal object to set the DIP switches,
because this may damage the DIP switches or the
pcb.
Use a suitable tool to set the DIP switches, such
DVDÀDWSODVWLFREMHFW
DIP switches on
the wall control
unit ON OFF
1
S1
ON
12345
• %XWWRQGH¿QHG
door OPEN
• %XWWRQGH¿QHG
door CLOSE
• Button 1 pulse
sequence
• Button 2 lighting
function /partial
opening
2S1
ON
12345
• "Relay" Door
status display:
Relay is activat-
ed during door
movement and
if the door is not
closed
• "Relay" lighting
function: Relay
can be used to
switch external
light
3S1
ON
12345
• No function • No function
4S1
ON
12345
• No function • No function
33
6. Connection and special functions of the wall control unit
the left or on the right side.
If the safety sensors are exposed to direct sunlight, the re-
ceiver (red sticker) should be installed on the side facing
away from the sun.
For garages with multiple doors (top view)
Fig. Installation on multiple doors
Install the safety sensors as shown in the diagram.
A = receiver (red sticker), B = transmitter (green sticker).
In this way, the safety sensors cannot influence each other
through stray light.
6.7 Installation
2”
2”
2”
1
2
2
2
1
3
Ø 3/16” 3/4”
Fig. 1 Fig. 2
1. Look for a suitable installation position for the mounting
bracket (1) inside the garage to the left and the right of
the door.
Hold the mounting bracket (1) to the wall and mark the
mounting points. The distance from the bottom edge
of the installation bracket to the floor is 2" (50 mm).
The height and angle of the bracket can be adjusted
through the slotted holes (2).
2. Drill holes for the screws. (3).
Screw in two screws (3).
WARNING
Risk of eye injury!
&KLSVÀ\LQJZKHQGULOOLQJPD\FDXVHVHULRXV
injuries to eyes and hands.
`Wear safety glasses when drilling.
6.6 Installation requirements and
dimensions
1"
<20’
< 20’
<20'
1"
Fig. Installation of safety sensors
DANGER
Danger of crushing and shearing!
If the assembly conditions are not complied
with during installation, malfunctions and error
messages may result when the safety sensors
is operated. This may result in serious injury or
even death.
The following assembly conditions must be
complied with:
`Select an installation location outside the
range of the opener and door mechanism.
`&RPSO\ZLWKDOOVSHFL¿HGLQVWDOODWLRQFRQGL-
tions and installation dimensions.
NOTE
If the following installation conditions and instal-
lation dimensions are not observed, malfunctions
and error messages may result.
$OOVSHFL¿FDWLRQVIRULQVWDOODWLRQRIWKHVDIHW\VHQ-
sors must be complied with.
NOTE
Never route the cable connection between the
safety sensors and the wall control unit along a
power supply line. This can cause the wall control
unit to malfunction. Observe the length of the
connection cable between safety sensors and wall
FRQWUROXQLW5RXWHWKHFDEOH¿UPO\
The safety sensors must be correctly connected and
aligned before the garage door opener will move in the
downward direction. Do not mount the safety sensors in
the area of the moving garage door. Mount at least 1"
(25 mm) away from it.
The distance between the transmitter and receiver of the
safety sensors set can range up to a maximum of 20'
(6.10 m).
The distance from the floor must be selected so that an ob-
stacle of 6" (152 mm) hight can be reliably detected. This
corresponds to a distance of 2" (50 mm) from the bottom
edge of the installation bracket to the floor.
The safety sensors kit consists of a transmitter (green
sticker) and a receiver (red sticker). Mount one safety sen-
sor to the left and one to the right of the door. As a general
rule, it does not matter which safety sensor is installed on
34
6. Connection and special functions of the wall control unit
2. Connect one wire of the receiver to terminal (COM)
and the other wire to terminal (Signal).
3. Check the function after connecting the 2-wire safety
sensors.
6.9 Functions of the buttons
1
2
3
4
Fig. Wall control unit - buttons
• /HIW 7XUQWKHOLJKWLQJRQDQGRႇ
• (2) Middle = Open, stopp and close the door
• (3) Right = Locking or unlocking the opener
• (4) Upper right corner, status LED = red: Operator
locked, green: Operator unlocked
7XUQLQJWKHOLJKWLQJRQDQGRႇ
The button (1) lights up green when the wall station is
ready for operation and the opener is not locked.
1. Press the button (1).
Opener lighting switched on.
2. Pressing the button (1) again switches the opener light-
ing back off.
2SHQHUOLJKWLQJRႇ
INFORMATION
,IWKHRSHQHUOLJKWLQJLVQRWVZLWFKHGRႇPDQXDOO\
LWVZLWFKHVRႇDXWRPDWLFDOO\DIWHUPLQXWHV7KLV
value can be changed via SOMlink and a WiFi-
enabled device.
The lighting cannot be switched off when the opener is
moving.
Opening, closing and stopping the door
1. Press the button (2) to open and close.
The door opens or closes depending on the starting
position.
2. Press the button (2) during the opening or closing
process.
The door stops:
3. Press the button (2) again.
The door moves into the respective starting position.
4.
4.
1
146
5
1
23
Fig. 3 Fig. 4 Fig. 5
3. Pre-attach the carriage bolt M6 (1) and the wing nut M6
(2) to the mounting bracket (3).
4. Slide the transmitter (4) over the head of the carriage
bolt M6 (1) and tighten the wing nut M6 (2). The posi-
tion of the safety sensors can be adjusted through the
slotted holes (5).
Mount the receiver on the opposite side in the same
way.
5. Run the two sets of wires (6) from the safety sensors to
the wall control unit.
6. Use staples to keep wires in place.
7. Connect to wall control unit.
6.8 Connection of the safety sensors
The 2-wire safety sensors from SOMMER must be con-
nected to the wall control unit. Initial operation is not possi-
ble without the safety sensors. The safety sensors are au-
tomatically detected during initial operation.
INFORMATION
During initial operation, the safety sensors must
not be actuated or the sensors interrupted by
persons or objects.
Fig: Terminal block for the 2-wire safety sensors
TX RX COM
Signal
Fig: Connecting diagramm for the 2-wire safety sensors
1. Connect one wire of the transmitter to terminal (COM)
and the other to terminal (Signal).
35
6. Connection and special functions of the wall control unit
Locking or unlocking the opener
Unauthorized access can be prevented by locking the
opener. For example in the absence of the user or to pre-
vent unintentional activation with a handheld transmitter.
The following functions are deactivated in the factory set-
tings when the lock button is activated:
• Radio (handheld transmitter)
• Senso ventilation function
• Control device (corded external button)
To lock:
The button (3) on the wall station lights up green when the
opener is unlocked. The button (3) lights up red when the
opener has been locked by the wall station.
1. Press and hold the button (3) for at least 5 seconds
with the door closed.
%XWWRQÀDVKHVJUHHQ
After 5 seconds, the button (3) lights up red.
Locking function activated.
All the functions of the opener are locked.
INFORMATION
If the door was still open, it can be closed using
the handheld transmitter. Only then are all opener
functions locked.
To unlock:
1. Press the button (3) for at least 5 seconds.
%XWWRQÀDVKHVUHG
Button (3) lights up green.
Locking function deactivated.
All the functions of the opener are activated again.
INFORMATION
All locking and unlocking functions can be
PRGL¿HGDQGDGMXVWHGZLWK620OLQNDQGD:L)L
enabled device. For more information ask your
specialist dealer.
6.10 Output OC
The door status can be displayed with the Output OC
(open collector output) accessory. Optional, external
lighting (Lumi Strip) DC 24V max. 750 mA can also be
switched. The function depends on the setting of the
DIP switches. See also chapter "6.4 Setting the DIP switch-
es on the wall control unit".
PAD
1
4
Fig. Relay slot for Output OC
The Output OC accessory part is plugged into the Relay
slot, see separate "Output OC" instructions.
6.11 Relay
External lighting such as the garage light, courtyard light or
door status display can be controlled with the relay acces-
sory part. The function depends on the setting of the DIP
switches. See also chapter "6.4 Setting the DIP switches
on the wall control unit".
PAD
1
4
Fig. Relay slot
The Relay is plugged into the Relay slot on the wall control
unit, see separate "Relay" instructions. The max. switch-
ing capacity is 250 V AC, 5 A or 24 V DC, 5 A.
DIP switches on
the wall control
unit
ON OFF
2S1
ON
12345
• "Relay" Door
status display:
Relay is activat-
ed during door
movement and
if the door is not
closed
• "Relay" lighting
function: Relay
can be used to
switch external
light
6.12 Installing the control unit cover of the
wall control unit
1. After working on the wall control unit, replace the con-
trol unit cover in reverse order, see "6.1 Control unit
cover of the wall control unit".
2. Connect the opener to the main power supply.
Check that the power supply is connected.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Sommer Pro+ Intelligent Garage Door Guide d'installation
- Catégorie
- Porte de garage
- Taper
- Guide d'installation