JVC KD-SX38MBT Mode d'emploi

Marque: JVC

Modèle: KD-SX38MBT

Taper: Mode d'emploi

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

ENGLISH

FRANÇAIS

ESPAÑOL

B5K-0997-00 [KN]

DIGITAL MEDIA RECEIVER

Quick Start Guide

RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE

Guide de démarrage rapide

RECEPTOR DE MEDIOS DIGITALES

Guía de inicio rápido

KD-SX38MBT

For detailed operations and information, refer to the INSTRUCTION MANUAL on the following

website:

Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur

le site web suivant:

Para obtener más información y detalles sobre las operaciones, consulte el MANUAL DE

INSTRUCCIONES en el siguiente sitio web:

<https://www.jvc.net/cs/car/>

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet.

Retain this information for future reference.

Model No.

Serial No.

KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd 1KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd 1 20/5/2022 10:18:26 AM20/5/2022 10:18:26 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida

útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de

residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser

desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final

de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento

adecuado a estos productos y a sus subproductos residuales correspondientes.

Póngase en contacto con su administración local para obtener información sobre el

punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación

de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos

perjudiciales en la salud y el medio ambiente.

Supplier's Declaration of Conformity

Trade Name: JVC

Products: DIGITAL MEDIA RECEIVER

Model Name: KD-SX38MBT

Responsible Party: JVCKENWOOD USA CORPORATION

4001 Worsham Avenue, Long Beach, CA 90808, U.S.A.

PHONE: 1-800-252-5722

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING

TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd iKD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd i 27/4/2022 3:48:31 PM27/4/2022 3:48:31 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su

operación no deseada”

Contains Bluetooth Module FCC ID: ZWY88112

IC ID: 12033A-88112

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is

copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions

which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.

This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the

Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or

indirectly from any third party. In such case, some third parties require the Users to follow their conditions

for use separately from this Software License Agreement. Such software shall not be subject to this

Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided

separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case

referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.

(the country where the User bought the Product (hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the

Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed

Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall

not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation

manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright

Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software

embedded in the Product (including any related materials, updates and upgrades) on condition that

no original, copies or related materials continue in the possession of the User, and that the User shall

cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code

analysis works in connection with the Licensed Software.

ISED Caution

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science

and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired

operation of the device.

Attention de ‘ISED

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage.

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

CAUTION

This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio

frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at

least 20 cm or more away from person’s body.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un

environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices

d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’ISED. Cet équipement

doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps

humain.

KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd iiKD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd ii 27/4/2022 3:48:31 PM27/4/2022 3:48:31 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

iii

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents

shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or

sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be

entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any

related documents.

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User

or any third party due to the exercise of the license granted to the User under this Agreement, unless

otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with

certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any

other intellectual property right that was caused by the User's use of the Licensed Software, the User shall

settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any

inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof

or any other information to be granted under this Agreement, as well as the conditions of this Agreement

as has not yet entered the public domain, and shall not disclose or divulge the same to any third party

without approval of the Licensor.

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may

immediately terminate this Agreement or claim that the User compensates for the damage incurred by the

Licensor due to such event:

(1) when the User violated any provision of this Agreement; or

(2) when a petition has been filed against the User for an attachment, provisional attachment,

provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed

Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software

shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the

ownership of the User.

2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country

of the User (including transmission thereof outside the country of the User via Internet of other

communication tools).

2. The User shall understand that the Licensed Software shall be subject to the export restrictions

adopted by the country of User and any other countries.

3. The User shall agree that the software will be subject to any and all applicable international and

domestic laws (including the export control regulation of the country of User and any other countries,

and any restrictions concerning the end-users, the use by end-users and importing countries to be

provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions

shall continue in force.

2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of

this Agreement shall be provided or settled upon good-faith consultation between the Licensor and

the User.

3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and

any dispute arising from, and relating to the rights and obligations under, this Agreement shall be

submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd iiiKD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd iii 27/4/2022 3:48:31 PM27/4/2022 3:48:31 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Important Notice concerning the Software

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated

documentation files (the "Software"), to deal in the Software without restriction, including without

limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following

conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions

of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY

CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,

ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

-cJSON

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated

documentation files (the "Software"), to deal in the Software without restriction, including without

limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following

conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions

of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY

CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,

ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

-CMP

The MIT License (MIT)

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated

documentation files (the "Software"), to deal in the Software without restriction, including without

limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following

conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions

of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY

CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,

ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

nanopb

This software is provided 'as-is', without any express or implied warranty. In no event will the authors be

held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications,

and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote

the original software. If you use this software in a product, an acknowledgment in the product

documentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the

original software.

3. This notice may not be removed or altered from any source distribution.

KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd ivKD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd iv 27/4/2022 3:48:32 PM27/4/2022 3:48:32 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

sha2

AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/

You may obtain a copy of the license at

https://opensource.org/licenses/BSD-3-Clause

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY

CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,

ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

Posix

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and

the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following

acknowledgement:

This product includes software developed by the University of California, Berkeley and its contributors.

4. Neither the name of the University nor the names of its contributors may be used to endorse or

promote products derived from this software without specific prior written permission.

Developed at SunPro, a Sun Microsystems, Inc. business.

Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is

preserved.

License to copy and use this software is granted provided that it is identified as the “RSA Data Security, Inc.

MD4 Message-Digest Algorithm” in all material mentioning or referencing this software or this function.

Author: Chris G. Demetriou

Permission to use, copy, modify and distribute this software and its documentation is hereby granted,

provided that both the copyright notice and this permission notice appear in all copies of the software,

derivative works or modified versions, and any portions thereof, and that both notices appear in supporting

documentation.

CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS “AS IS” CONDITION. CARNEGIE MELLON

DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF

THIS SOFTWARE.

Carnegie Mellon requests users of this software to return to

Software Distribution Coordinator or Software.Distribution@

CS.CMU.EDU

School of Computer Science

Carnegie Mellon University

Pittsburgh PA 15213-3890

any improvements or extensions that they make and grant Carnegie the rights to redistribute these

changes.

License is also granted to make and use derivative works provided that such works are identified as

“derived from the RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material mentioning or

referencing the derived work.

RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or

the suitability of this software for any particular purpose. It is provided “as is” without express or implied

warranty of any kind.

You may redistribute unmodified or modified versions of this source code provided that the above

This software is provided “as is”, and comes with no warranties of any kind. I shall in no event be liable for

anything that happens to anyone/anything when using this software.

These notices must be retained in any copies of any part of this documentation and/or software.

KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd vKD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd v 27/4/2022 3:48:32 PM27/4/2022 3:48:32 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

T-Kernel 2.0

This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum

(www.tron.org)

BSD-3-Clause

You may obtain a copy of the license at

https://opensource.org/licenses/BSD-3-Clause

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,

OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

LFS Subsystem

You may obtain a copy of the license at

https://directory.fsf.org/wiki/License:BSD-4-Clause

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,

OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Accordo2 Player

Apache License

Licensed under the Apache License,

Version 2.0, January 2004(the “License”);

You may obtain a copy of the license at

http://www.apache.org/licenses/LICENSE-2.0

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,

OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

KD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd viKD-SX38MBT_K_B5K-0997-00_Cover_1st Draft.indd vi 27/4/2022 3:48:32 PM27/4/2022 3:48:32 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Basic procedure

1 Remove the key from the ignition switch, then disconnect the

terminal of the car battery.

2 Connect the wires properly. See “Wiring connection” on page 3.

3 Install the unit to your car. See the following “Installing the unit

(in-dash mounting)”.

4 Connect the terminal of the car battery.

5 Press B SRC to turn on the power.

6 Detach the faceplate and reset the unit within 5 seconds. See “How to

reset” on page 4.

Installing the unit (in-dash mounting)

Installation/Connection

This section is for the professional installer.

For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.

WARNING

• The unit can only be used with a 12 V DC power supply, negative ground.

• Disconnect the battery’s negative terminal before wiring and mounting.

• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to

prevent a short circuit.

• To prevent short circuit:

– Insulate unconnected wires with vinyl tape.

– Be sure to ground this unit to the car’s chassis again after installation.

– Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into contact with

metal parts to protect the wires.

CAUTION

• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly

after use of the unit. Metal parts such as the heat sink and enclosure become hot.

• Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in

parallel.

• Connect speakers with a maximum power of more than 50 W. If the maximum power of the speakers is

lower than 50 W, change the

[AMPGAIN]

setting to avoid damaging the speakers.

• Mount the unit at an angle of less than 30º.

• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the

terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the

ignition key.

• Keep all cables away from heat dissipate metal parts.

• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working

properly.

• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with

one that has the same rating.

Hook on the top side

Bend the appropriate tabs to hold the

sleeve firmly in place.

Dashboard of your car

KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 2KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 2 27/4/2022 3:48:57 PM27/4/2022 3:48:57 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Wiring connection

a Light blue/yellow: To the

steering wheel remote control

adapter

b Brown (not used)

c Blue: To power antenna

d Blue/white: To amplifier

e Blue/white: Remote

(12 V 350mA)

f Orange/white: Illumination

g Yellow: Battery 12V

h Red: Ignition 12V

i Black: Ground

j Gray ª, Gray/black ·:

Front speaker (right)

k White ª, White/black ·:

Front speaker (left)

l Purple ª, Purple/black ·:

Rear speaker (right)

m Green ª, Green/black ·:

Rear speaker (left)

Removing the unit

Installing the unit (without mounting sleeve)

1 Remove the mounting sleeve and trim plate from the unit.

2 Align the holes in the unit (on both sides) with the vehicle

mounting bracket and secure the unit with screws (commercially

available).

Part list (supplied)

(A) Faceplate (×1)

(B) Trimplate (×1)

(D) Wiring harness (×1)

(E) Extraction key (×2)

Use only the specified screws.

Using wrong screws might damage

the unit.

Join the same color

wires together.

Custom wiring harness

(separately purchased)

Vehicle dashboard

Recommended connection

Factory wiring

harness (vehicle)

Antenna terminal

Fuse (10 A)

KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 3KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 3 27/4/2022 3:49:00 PM27/4/2022 3:49:00 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Basics (on faceplate)

Volume knob

USB input

terminal

Detach button

Display window*1

Auxiliary

input jack

*1 Only for illustration purpose.

Attach Detach How to reset

Reset the unit

within 5seconds

after detaching the

faceplate.

To On the faceplate

Turn on the power Press B SRC.

• Press and hold to turn off the power.

Adjust the volume Turn the volume knob.

Select a source Press B SRC repeatedly.

Change the display information*2 Press repeatedly.

*2 One of the display information supports Music Synchronization Effect. The illumination color or brightness level of

the buttons changes and synchronizes with the music level.

Before Use

IMPORTANT

• To ensure proper use, please read through this Guide before using

this product. It is especially important that you read and observe

Warnings and Cautions in this Guide.

• Please keep the Guide in a safe and accessible place for future

reference.

WARNING

Do not operate any function that takes your attention away from safe

driving.

CAUTION

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to

prevent accidents.

• Lower the volume before playing digital sources to avoid

damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the external device if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no

responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal

tools) inside the unit to prevent a short circuit.

• Depending on the types of cars, the antenna will automatically

extend when you turn on the unit with the antenna control wire

connected. Turn off the unit when parking at a low ceiling area.

KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 4KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 4 27/4/2022 3:49:00 PM27/4/2022 3:49:00 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Getting Started

1 Acknowledge the crossover type

When you turn on the power for the first time (or

[FACTORY RESET]

is set to

[YES]

), the display shows: “2-WAY X’OVER” or “3-WAY X’OVER” “PRESS”

“VOLUME KNOB” “TO CONFIRM”.

Press the volume knob to acknowledge the current crossover type.

2 Set the clock and date

1 Press and hold .

2 Turn the volume knob to select

[CLOCK]

, then press the knob.

To adjust the clock

3 Turn the volume knob to select

[CLOCKADJUST]

, then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Set the time in the order of “Hour” “Minute”.

5 Turn the volume knob to select

[CLOCK FORMAT]

, then press the knob.

6 Turn the volume knob to select

[12H] or [24H]

, then press the knob.

To set the date

7 Turn the volume knob to select

[DATESET]

, then press the knob.

8 Turn the volume knob to make the settings, then press the knob.

Set the date in the order of “Day” “Month” “Year”.

9 Press to exit.

To return to the previous setting item, press .

3 Set the basic settings

1 Press and hold .

2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected or activated.

4 Press to exit.

To return to the previous setting item, press .

Default: [XX]

[SYSTEM]

[KEY BEEP] (Not applicable when 3-way crossover is selected.)

[ON]: Activates the keypress tone. ; [OFF]: Deactivates.

[FACTORY RESET] [YES]: Resets the settings to default (except the stored station). ;

[NO]: Cancels.

[CLOCK]

[CLOCK DISPLAY] [ON]: The clock time is shown on the display even when the unit is

turned off. ; [OFF]: Cancels.

[ENGLISH] Select the display language for menu and music information if

applicable.

By default, [ENGLISH] is selected.

[ESPANOL]

KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 5KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 5 27/4/2022 3:49:00 PM27/4/2022 3:49:00 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Radio

Search for a station

1 Press B SRC repeatedly to select FM or AM.

2 Press S / T to search for a station automatically.

(or)

Press and hold S / T until “M” flashes, then press repeatedly to

search for a station manually.

Settings in memory

You can store up to 18 stations for FM and 6 stations for AM.

Store a station

While listening to a station....

Press and hold one of the number buttons (1 to 6).

(or)

1 Press and hold the volume knob until “PRESETMODE” flashes.

2 Turn the volume knob to select a preset number, then press the knob.

“MEMORY” appears once the station is stored.

Select a stored station

Press one of the number buttons (1to6).

(or)

1 Press .

2 Turn the volume knob to select a preset number, then press the knob.

USB

Selectable source: USB

Start playback

The source changes automatically and playback starts when you attach a

USB device to the USB input terminal.

To On the faceplate

Reverse/Fast-forward Press and hold S / T.

Select a file Press S / T.

Select a folder Press 2 J / 1 K.

Repeat play Press 4  repeatedly.

Random play Press 3  repeatedly.

KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 6KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 6 27/4/2022 3:49:01 PM27/4/2022 3:49:01 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Menu Settings

1 Press and hold to enter menu settings.

2 Turn the volume knob to select an item, then press the knob.

3 Repeat step 2 until the desired item is selected/activated.

4 Press to exit.

To return to the previous setting item, press .

• Refer to the INSTRUCTION MANUAL on the following website for the

detailed explanation of each item: <https://www.jvc.net/cs/car/>

Menu items

[EQ SETTING]

: Selects a preset equalizer or adjusts your own sound

settings.

[AUDIO CONTROL]

: Sets your preferred audio settings.

[SOUND EFFECT]

: Sets your preferred sound effect.

[DISPLAY]

: Sets your preferred control for the display window.

[COLOR]

: Sets your preferred illumination color for buttons.

[TUNER SETTING]

: Settings for radio source.

[BT MODE]

: Settings for using a Bluetooth device.

[REMOTE APP]

: Settings for using smartphone to control this unit.

[MIC GAIN]

* : Sets the sensitivity of the microphone.

[NR LEVEL]

* : Adjusts the noise reduction level.

[ECHO CANCEL]

* : Adjusts the echo cancellation delay time.

[SYSTEM]

: Settings for this unit.

[CLOCK]

: Adjusts the clock.

[ENGLISH]

: Selects language for the menu and music information.

[ESPANOL]

: Selects language for the menu and music information.

* Applicable only while talking on the phone.

Examples of some well-used settings

Subwoofer Level Setting

1 Press and hold to enter menu settings.

2 Turn the volume knob clockwise to select

[AUDIO CONTROL]

, then press

the knob.

3 Turn the volume knob clockwise to select

[SUBWOOFER SET]

, then press

the knob.

4 Turn the volume knob clockwise to select

[ON]

, then press the knob.

5 Turn the volume knob clockwise to select

[SUB.W LEVEL]

, then press the

knob.

6 Press the volume knob if

[PRE-OUT]

is shown on the display.

Turn the volume knob to adjust the subwoofer level, then press the knob.

Continued on the next page...

KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 7KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 7 27/4/2022 3:49:01 PM27/4/2022 3:49:01 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

5 Turn the volume knob to choose a color, then press the knob.

•

[COLOR01]

[COLOR49]

•

[USER]

: The color you have created for

[DAYCOLOR]

[NIGHTCOLOR]

is shown.

•

[COLORFLOW01]

[COLORFLOW03]

: Color changes at

different speeds.

•

[CRYSTAL]

[FLOWER]

[FOREST]

[GRADATION]

[OCEAN]

[RELAX]

[SUNSET]

: The selected color pattern is

shown. (Selectable only when

[ALLZONE]

is selected

in step4.)

6 Repeat step 4 and step 5 to set color for other zones.

7 Press to exit.

Other Information

For playback operations of AUX source, refer to the INSTRUCTION MANUAL

on the following website: <https://www.jvc.net/cs/car/>

Note for specifications

Bluetooth Frequency Range:

2.402 GHz — 2.480 GHz

Speaker Impedance:

4Ω—8Ω

Operating Voltage:

12 V DC car battery

8 Press to exit the setting menu.

Note:

You need to set

[SPK/PRE OUT]

[REAR/SUB.W]

[SUB.W/SUB.W]

before you can

make the subwoofer level settings.

Illumination Color Setting

You can set your preferred illumination color for each zone.

1 Press and hold to enter menu settings.

2 Turn the volume knob clockwise to select

[COLOR]

, then press the knob.

3 Press the volume knob if

[PRESET]

is shown on the display.

4 Turn the volume knob to choose a zone (

[ALL ZONE]

[ZONE 1]

[ZONE 2]

then press the knob.

KD-SX38MBT_K_B5K-0997-00_EN_2nd Draft.indd 8KD-SX38MBT_K_B5K-0997-00_EN_2nd Draft.indd 8 14/6/2022 3:47:36 PM14/6/2022 3:47:36 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Bluetooth®

• Depending on the Bluetooth version, operating system and the

firmware version of your mobile phone, Bluetooth features may not

work with this unit.

• Be sure to turn on the Bluetooth function of the device to make the

following operations.

• Signal conditions vary depending on the surroundings.

Connect the microphone

Connect the supplied microphone to the microphone input jack on the rear

panel.

Adjust the

microphone

angle

Secure using cord

clamps (not supplied)

if necessary.

Pair and connect a Bluetooth device for the first time

1 Press B SRC to turn on the unit.

2 Search and select the name of your receiver (“KD-SX38MBT”) on the

Bluetooth device.

3 Perform (A) or (B) depending on what appears on the display.

For some Bluetooth devices, pairing sequence may vary from the steps

described below.

(A) “[Device Name]” “XXXXXX” “VOL–YES” “BACK–NO”

“XXXXXX” is a 6-digit passkey randomly generated during each pairing.

Ensure that the passkeys appear on the unit and Bluetooth device

are the same.

Press the volume knob to confirm the passkey.

Operate the Bluetooth device to confirm the passkey.

(B) “[Device Name]” “VOL–YES” “BACK–NO”

Press the volume knob to start pairing.

• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code

“0000” into the Bluetooth device.

• If only “PAIRING” appears, operate the Bluetooth device to confirm

pairing.

“PAIRING COMPLETED” appears when pairing is completed and “ ” will light

up when the Bluetooth connection is established.

Answer a call

Press or the volume knob.

• To adjust the phone volume

[00]

[35]

, turn the volume knob.

• To end a call, press and hold or the volume knob.

Audio player via Bluetooth

1 Press B SRC repeatedly to select BTAUDIO.

• Pressing enters BT AUDIO directly.

2 Operate the audio player via Bluetooth to start playback.

To On the faceplate

Play back/pause Press the volume knob.

Select group or folder Press 2 J / 1 K.

Reverse skip/Forward skip Press S / T.

Reverse/Fast-forward Press and hold S / T.

Repeat play Press 4  repeatedly.

Random play Press 3  repeatedly.

KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 9KD-SX38MBT_K_B5K-0997-00_EN_1st Draft.indd 9 27/4/2022 3:49:02 PM27/4/2022 3:49:02 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Procédure de base

1 Retirez la clé de contact, puis déconnectez la borne de la batterie de la

voiture.

2 Connectez les fils correctement. Voir “Connexions” à la page3.

3 Installez l’appareil dans votre voiture. Reportez-vous à “Installation de

l’appareil (montage encastré)” ci-après.

4 Connectez la borne de la batterie de la voiture.

5 Appuyez sur B SRC pour mettre l’appareil sous tension.

6 Détachez la façade et réinitialisez l’appareil avant 5 secondes. Voir

“Comment réinitialiser” à la page4.

Installation de l’appareil (montage encastré)

Installation/Connexion

Cette section est réservée aux installateurs professionnels.

Pour des raison de sécurité, laissez le travail de câblage et de montage des professionnels. Consultez

votre revendeur autoradio.

MISE EN GARDE

• L’appareil peut uniquement être utilisé avec une alimentation de 12 V CC, à masse négative.

• Déconnectez la borne négative de la batterie avant le câblage et le montage.

• Ne connectez pas le fil de batterie (jaune) et le fil d’allumage (rouge) au châssis de la voiture ou au fil de masse

(noir) pour éviter les courts-circuits.

• Pour éviter les courts-circuits:

– Isolez les fils non connectés avec du ruban adhésif.

– Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après

l’installation.

– Fixez les câbles avec des serre-câbles et enrouler un ruban de vinyle autour des câbles qui entrent en contact

avec des pièces métalliques pour protéger les câbles.

AVERTISSEMENT

• Installez cet appareil dans la console de votre véhicule. Ne touchez pas les parties métalliques de cet appareil

pendant ou juste après son utilisation. Les parties métalliques, comme le dissipateur de chaleur et le boîtier,

deviennent chaudes.

• Ne connectez pas les fils des l’enceintes au châssis de la voiture, au fil de masse (noir) ou en parallèle.

• Connectez des enceintes avec une puissance maximum de plus de 50 W. Si la puissance maximum des enceintes

est inférieure à 50W, changez le réglage

[AMPGAIN]

pour éviter d’endommager les enceintes.

• Montez l’appareil avec un angle de moins de 30º.

• Si le faisceau de fils de votre véhicule ne possède pas de borne d’allumage, connectez le fil d’allumage (rouge) à la

borne du boîtier de fusible de votre véhicule qui offre une alimentation de 12 V CC et qui se met en et hors service

avec la clé de contact.

• Gardez tous les câbles à l’écart des dissipateurs thermiques.

• Après avoir installé l’appareil, vérifiez si les lampes de frein, les indicateurs, les clignotants, les essuie-glaces, etc.

de la voiture fonctionnent correctement.

• Si un fusible saute, assurez-vous d’abord que les câbles ne touches pas le châssis de la voiture puis remplacez le

vieux fusible par un nouveau de même valeur.

Crochet sur le

côté supérieur

Tordez les languettes appropriées pour

maintenir le manchon en place.

Tableau de bord de votre voiture

KD-SX38MBT_K_QSG_FR.indd 2KD-SX38MBT_K_QSG_FR.indd 2 30/9/2022 9:42:03 AM30/9/2022 9:42:03 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Connexions

a Bleu clair/jaune: À l’adaptateur

de télécommande volant

b Marron (non utilisé)

c Bleu: À l’antenne alimentée

d Bleu/blanc: À l’amplificateur

e Bleu/blanc: Télécommande

(12 V 350mA)

f Orange/blanc: Éclairage

g Jaune: Batterie 12 V

h Rouge: Allumage 12V

i Noir: Masse

j Gris ª, Gris/noir ·:

Enceinte avant (droite)

k Blanc ª, Blanc/noir ·:

Enceinte avant (gauche)

l Violet ª, Violet/noir ·:

Enceinte arrière (droite)

m Vert ª, Vert/noir ·:

Enceinte arrière (gauche)

Retrait de l’appareil

Installation de l’appareil (sans le manchon de montage)

1 Retirez le manchon de montage et la plaque de garniture de l’appareil.

2 Alignez les entailles de l’appareil (des deux côtés) avec le support de

montage du véhicule et fixez l’appareil avec les vis (en vente dans le

commerce).

Liste de pièces (fourni)

(A) Façade (×1)

(B) Plaque de garniture (×1)

(D) Faisceau de fils (×1)

(E) Clé d’extraction (×2)

N’utiliser que les vis spécifiés.

L’utilisation de vis incorrects peut

endommager l’appareil.

Joignez les fils de même

couleur ensemble.

Faisceau de fils personnalisé

(vendu séparément)

Tableau de bord

du véhicule

Connexion recommandée

Faisceau de câbles de

l’usine (véhicule)

Borne de l’antenne

Fusible (10 A)

KD-SX38MBT_K_QSG_FR.indd 3KD-SX38MBT_K_QSG_FR.indd 3 30/9/2022 9:42:04 AM30/9/2022 9:42:04 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Fonctionnement de base (sur la façade)

Bouton de volume

Prise d’entrée

USB

Touche de détachement

Fenêtre d’affichage*1

Prise d’entrée

auxiliaire

*1 Uniquement à des fins d’illustration.

Attachez Détachez Comment réinitialiser

Réinitialisez l’appareil en

moins de 5 secondes

après avoir détaché la

façade.

Pour Sur la façade

Mettez l’appareil sous tension Appuyez sur B SRC.

• Maintenez la touche enfoncée pour mettre

l’appareil hors tension.

Ajustez le volume Tournez le bouton de volume.

Sélectionner la source Appuyez répétitivement sur B SRC.

Changez l’information sur

l’affichage*2 Appuyez répétitivement sur .

*2 Une des informations de l’affichage prend en charge l’effet de synchronisation musicale. La couleur d’éclairage ou le niveau

de luminosité des touches change et est synchronisé avec le niveau de la musique.

Avant l’utilisation

IMPORTANTES

• Pour utiliser correctement l’appareil, veuillez lire ce Guide complément

avant de l’utiliser. Il est particulièrement important que vous lisiez et

acceptiez les avertissements et les précautions de ce Guide.

• Veuillez garder ce Guide dans un endroit sûr et accessible pour une

utilisation future.

MISE EN GARDE

N’utilisez aucune fonction qui risque de vous distraire de la conduite sure

de votre véhicule.

AVERTISSEMENT

Réglage du volume:

• Ajustez le volume de façon à pouvoir entendre les sons extérieurs à la

voiture afin d’éviter tout risque d’accident.

• Réduisez le volume avant de reproduire des sources numériques afin

d’éviter d’endommager les enceintes par la soudaine augmentation du

niveau de sortie.

Généralités:

• Éviter d’utiliser le périphérique extérieur s’il peut gêner une conduite en

toute sécurité.

• Assurez-vous que toutes les données importantes ont été sauvegardées.

Nous ne pouvons pas être tenu responsable pour toute perte des

données enregistrées.

• Veuillez faire en sorte de ne jamais mettre ou laisser d’objets métalliques

(tels que des pièces ou des outils) dans l’appareil, afin d’éviter tout

risque de court-circuit.

• En fonction du type de voiture, l’antenne s’étendra automatiquement

quand vous mettrez l’appareil sous tension si le câble de commande

d’antenne est connecté. Mettez l’appareil hors tension quand vous vous

garez dans un parking avec un plafond bas.

KD-SX38MBT_K_QSG_FR.indd 4KD-SX38MBT_K_QSG_FR.indd 4 30/9/2022 9:42:04 AM30/9/2022 9:42:04 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Prise en main

1 Vérifiez le type de transition

Quand vous mettez l’appareil sous tension pour la première fois (ou que

[FACTORYRESET]

est réglé sur

[YES]

), l’affichage montre: “2-WAY X’OVER” ou

“3-WAYX’OVER” “PRESS” “VOLUME KNOB” “TO CONFIRM”.

Appuyez sur le bouton de volume pour valider le type de transition actuel.

2 Réglez l’horloge et la date

1 Maintenez enfoncée .

2 Tournez le bouton de volume pour choisir

[CLOCK]

, puis appuyez sur le

bouton.

Pour ajuster l’horloge

3 Tournez le bouton de volume pour choisir

[CLOCKADJUST]

, puis appuyez sur

le bouton.

4 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le

bouton.

Réglez l’heure dans l’ordre “Heures” “Minutes”.

5 Tournez le bouton de volume pour choisir

[CLOCK FORMAT]

, puis appuyez sur

le bouton.

6 Tournez le bouton de volume pour choisir

[12H] ou [24H]

, puis appuyez sur

le bouton.

Pour régler la date

7 Tournez le bouton de volume pour choisir

[DATESET]

, puis appuyez sur le

bouton.

8 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le

bouton.

Réglez la date dans l’ordre “Jour” “Mois” “Année”.

9 Appuyez sur pour quitter.

Pour retourner à l’option de réglage précédente, appuyez sur .

3 Faites les réglages de base

1 Maintenez enfoncée .

2 Tournez le bouton de volume pour sélectionner un élément (voir le tableau

suivant), puis appuyez sur le bouton.

3 Répétez l’étape 2 jusqu’à ce que l’élément souhaité soit sélectionné ou

activé.

4 Appuyez sur pour quitter.

Pour retourner à l’option de réglage précédente, appuyez sur .

Défaut: [XX]

[SYSTEM]

[KEY BEEP] (Non applicable quand la transition 3 voies est sélectionnée.)

[ON]:Met en service la tonalité des touches.; [OFF]:Met hors service la

fonction.

[FACTORY RESET] [YES]:Réinitialise les réglages aux valeurs par défaut (sauf la station

mémorisée).; [NO]:Annulation.

[CLOCK]

[CLOCK DISPLAY] [ON]:L’horloge apparaît sur l’affichage même quand l’appareil est hors

tension.; [OFF]:Annulation.

[ENGLISH] Sélectionnez la langue d’affichage pour le menu et l’information sur le

morceau si elle est disponible.

Par défaut, [ENGLISH] est sélectionné.

[ESPANOL]

KD-SX38MBT_K_QSG_FR.indd 5KD-SX38MBT_K_QSG_FR.indd 5 30/9/2022 9:42:04 AM30/9/2022 9:42:04 AM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Radio

Recherchez une station

1 Appuyez répétitivemenent sur B SRC pour sélectionner FM ou AM.

2 Appuyez sur S / T pour rechercher une station automatiquement.

(ou)

Maintenez en enfoncé S / T jusqu’à ce que “M” clignote, puis appuyez

répétitivement dessus pour rechercher une station manuellement.

Réglages en mémoire

Vous pouvez mémoriser un maximum de 18 stations pour FM et de 6 stations

pour AM.

Mémorisez une station

Pendant l’écoute d’une station....

Maintenez enfoncée une des touches numériques (1 à 6).

(ou)

1 Maintenez enfoncé le bouton de volume jusqu’à ce que “PRESETMODE”

clignote.

2 Tournez le bouton de volume pour choisir un numéro de préréglage, puis

appuyez sur le bouton.

“MEMORY” apparaît une fois que la station est mémorisée.

Sélectionnez une station mémorisée

Appuyez sur l’une des touches numériques (1 à 6).

(ou)

1 Appuyez sur .

2 Tournez le bouton de volume pour choisir un numéro de préréglage, puis

appuyez sur le bouton.

USB

Source sélectionnable: USB

Démarrez la lecture

La source change automatiquement et la lecture démarre quand vous connectez

un périphérique USB à la prise d’entrée USB.

Pour Sur la façade

Recherche rapide vers

l’arrière/vers l’avant Maintenez enfoncée S / T.

Sélectionnez un fichier Appuyez sur S / T.

Sélectionnez un dossier Appuyez sur 2

J / 1 K.

Lecture répétée Appuyez répétitivement sur 4

.

Lecture aléatoire Appuyez répétitivement sur 3

.

KD-SX38MBT_K_QSG_FR.indd 6KD-SX38MBT_K_QSG_FR.indd 6 30/9/2022 9:42:04 AM30/9/2022 9:42:04 AM

La page charge ...

JVC KD-SX38MBT Mode d'emploi

Marque: JVC

Modèle: KD-SX38MBT

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: JVC KD-SX38MBT User guide
español: JVC KD-SX38MBT Guía del usuario

JVC KD-SX38MBT Mode d'emploi

JVC KD-SX38MBT Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents