INSTALLATION INSTRUCTIONS
ARGO
FM-4407, FM-4411
Wire Connector
Qty: 3 pcs
P3
HARDWARE
Junction Box Screw
Qty: 2 pcs
#8-32, * 3/4”
Stainless Steel
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019 1
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE
CIRCUIT BREAKER BEFORE BEGINNING.
•Read all instructions before installing.
•System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC)
and local regulations.
•When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
•Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the
supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not
designated for use with this product by Modern Forms could result in personal injury or property damage, and will void
the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that
customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
•Lisez toutes les instructions avant l’installation.
•Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et
également aux règlements locaux.
•Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour
être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms.
Remplacer des pièces ou accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages
corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé
ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le
luminaire. Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces
externes du luminaire une fois toutes les deux semaines avec un chiffon humide.
INSTALLATION INSTRUCTIONS
ARGO
FM-4407, FM-4411
4.
5.
INSTALLATION
Uses 3”, 4", or a combination 3/0-4/0 junction box.
1. Install the mounting plate to the junction box using the
junction box screws provided.
NOTE: Carefully align the slots on the mounting plate
with the direction you want your fixture to be in to
prevent uneven installation.
2. Provide electrical service according to the “National
Electrical Code” or your local electrical code to the
outlet box.
3. Clip the retention cable into the retention cable slot
on the mounting plate to assist with wiring.
Connect supply wires to fixture wires and insulate with
proper wire nuts.Connect incoming ground wire to
mounting plate ground wire (green or bare). Connect
incoming common wire to fixture common (white).
Connect incoming hot wire to fixture black wire.
Raise the fixture to the junction box, guide the spring
clips into the slots in the mounting plate and press the
front of the fixture firmly in the center to lock the fixture
in place.
Note: To ensure an easier installation, guide the
spring clips through the slots on one side first before
guiding the spring clips on the other side. Push all four
clips in simultaneously.
3", 4" or 3/0-4/0 Junction Box
Junction Box Mounting
Screw Retention Cable Slot
Mounting Plate Slot
Mounting Plate
Wire Connector
Fixture
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019 2
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Fig. 1
-
1
-
2
dans d''autres langues
Documents connexes
-
Modern Forms PD-66110 Ingot Mode d'emploi
-
-
-
-
-
-
-
-
-