Modern Forms WS-W22115 Revere Mode d'emploi
- Taper
- Mode d'emploi
retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep. 2020
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
221- Outdoor Wall Sconce
WS-W22115 / WS-W22120 /WS-W22125
HARDWARE
Modern Forms
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
ɰ Read all instructions before installing.
ɰ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
ɰ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
ɰ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal
areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
ɰ Lisez toutes les instructions avant l’installation.
ɰ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
ɰ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chiffon humide.
Wire Connector
Qty:3+1Extra
$
%
Mounting Screw
Qty:1Extra
(
Allen Wrench
Qty:1pc
&
Rubber Gasket
Qty:1Extra
'
Fixed Screw
Qty:1Extra
retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep. 2020
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
221 - Outdoor Wall Sconce
WS-W22115 / WS-W22120 / WS-W22125
PREPARATION
MOUNTING THE FIXTURE (Fig. 1)
CONNECTING THE WIRES (Fig. 2)
COMPLETING THE INSTALLATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
3. Remove the mounting screw (B) and the rubber gasket (C) from the back plate.
4. Secure the back plate to the junction box using junction box screws. The side of the back plate marked “GND ” must face out.
5. Connect the fixture’s wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has a
green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate
using the GND screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Secure the fixture to the back plate using the mounting screw (B) and the rubber gasket (C).
6. Remove the fixed screw (D) using Allen Wrench (E) and the base cap from the aluminum frame.
7. Insert the clear hammered seedy glass into the top cap, then secure the base cap to the aluminum frame using the fixed screw (D).
9. To prevent moisture from entering the outlet box and causing a short circuit, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline
the outside of the back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig.3.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fi g. 1
Back Plate Dimensions
7MBC151106
Junction Box
Caulking
Fig. 3 Sealing
A
B
C
D
Wire Connector
Mounting Screw
Rubber Gasket
Aluminum Frame
Base Cap
Top Cap
Fixed Screw
E
Allen Wrench
Junction Box
GND Screw
Back Plate
Junction Box Screw
(RPL-GLA-22115)
(RPL-GLA-22120)
(RPL-GLA-22125)
Modern Forms
5 11/16”
1 3/4”
1 3/8”
4 3/4”
Clear Hammered
Seedy Glass
-
1
-
2
Modern Forms WS-W22115 Revere Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-W54016 Mist Mode d'emploi
-
-
-
-
-
-
-
-
-