Audio Note CDT ZERO Transport Owner's Information

Catégorie
Lecteur CD
Taper
Owner's Information
- -
1
Congratulations on your purchase of the Audio Note CDT ZERO Transport.
Audio Note is highly critical of the digital medium as presented by compact disc; we
sincerely hope that you too will find this transport breaks free from the ‘digital mould’
that we are all so accustomed to, and so open a new window on your CD collection.
Please read over this manual carefully in order to obtain the best possible
performance and longevity from your transport.
TABLE OF CONTENTS
PRECAUTIONS
UNPACKING & INSTALLATION
OPERATIONS (Via Remote Control)
LOADING
CD PLAYBACK Ÿ TIME DISPLAY
GOING TO THE PREVIOUS/NEXT TRACK
RANDOM PLAYBACK
REMOTE CONTROL
TROUBLESHOOTING GUIDE
SPECIFICATIONS
- -
2
PRECAUTIONS
Never touch the power cord with wet hands.
Always pull the power cord out by the plug, not by the cord.
Never expose the system to rain, moisture, excessive heat and magnetism.
Never let an inexperienced person repair or reassemble the unit.
Never put anything, especially metal, into the unit.
Never place excessive weight on the unit.
POWER REQUIREMENTS
Power requirements for electrical equipment differ from area to area. Please ensure
that your unit meets the power requirements in your area. The power requirement for
your transport is marked on the serial number plate on the rear panel.
If you are in doubt, please contact your dealer before plugging the unit into the
mains supply!
CLASS 1 LASER PRODUCT
This product contains a low power laser device. To ensure continued safety, do not
remove any covers or attempt to gain access to the inside of the product. Refer
servicing to qualified personnel.
Make Your Contribution to Protect the Environment
Used batteries with the ISO symbol for recycling, as well as small accumulators
(rechargeable batteries), mini-batteries (cells) and starter batteries should not be
thrown into the dustbin. Please leave them at an appropriate depot.
This equipment conforms to No. 62/499/EEC, 87/308/EEC standard.
- -
3
-2-
- -
4
UNPACKING & INSTALLATION.
Please take care when unpacking the CDT ZERO. We recommend that you store
the packing materials in case the unit requires shipping at a later date.
Next, select a suitable location for the unit, for example, a dry and dust-free area
which is not exposed to direct sunlight.
Connections:
The transport’s sonic performance will start to improve as the internal parts ‘bed’ in.
The transport requires about two hundred hours of operation before the bedding in
process is complete.
A single connector provides a digital output for connection to your DAC via your digital
input RCA connector. Your dealer can advise on suitable type and quality of cable
eg:- Audio Note is a excellent choice.
Power connector: An IEC power connector is available for connection to the local
supply. Simply connect this to a convenient power point using the supplied cable.
IMPORTANT INFORMATION
Compact disc transports have built-in error compensation circuits to correct minor
manufacturing defects on a disc. In some cases, defects on the disc, which are too
large for the error compensation circuits to handle, may cause the CD player to skip
some tracks during playback. If this problem occurs, play a new disc, normal
playback of the new disc indicates that the previous disc is damaged in some way.
However, if the problem continues, it is best to have the unit serviced.
-3-
- -
5
OPERATIONS
VIA REMOTE CONTROL.
The batteries supplied with the CDT ZERO should be fitted into the remote control
before operating the remote control. Please ensure that the batteries are inserted
correctly.
PLAY/PAUSE button Press this button to play a disc. Pressing this button
again will pause playback. Press the button again to resume playback.
STOP button Press this button to stop playback.
OPEN/CLOSE Press this button to open or close the tray.
MEMORY Use the Memory button for programming and reviewing programs.
PROGRAMMING
You may select a number of tracks and store them in the memory in the desired
sequence. The transport will then play back only your selection of tracks in the
selected order.
. 1 Press the MEMORY button. ‘MEMORY’ will appear on the display.
. 2 Press the CD SKIP buttons To select the desired track to be stored.
. 3 Press the MEMORY button The track is now stored in the memory.
. Repeat steps 2 and 3 to complete programming.
. 4 Press play to hear the programmed tracks.
. 5 Press stop once to stop music. #
. 6 Press stop a second time to clear programming.
A maximum of 32 tracks may be stored.
A particular track in your selection may be replaced with a new one if the original
selection was made in error. Simply store the new track in the program number
to be replaced.
-4-
- -
6
# To review the programming, press the MEMORY button. The program number
and its track will appear on the display.
NOTE: Programming may not be made during playback.
SKIP buttons.
Press these buttons to go to the previous or the next track.
SEARCH buttons.
Press these buttons to cue or review a track.
FTo reverse (review) a track, hold down the CD SEARCH button.
FTo cue (fast forward) a track, hold down the CD SEARCH + button.
NOTE:
The Cue and Review feature may be used when the CD player is in either play or
pause mode. In both instances, a visual indication of the playing time of the track
that has been cued or reviewed will be indicated on the display. Using this
feature with the CD player in Pause mode will mute the sound whilst cueing or
reviewing. Once the desired point on the track has been found, simply resume
playback by pressing Play.
TIME button.
Press this button to see the elapsing time or remaining time of the CD. (Play
mode only.)
FPress the TIME button and select the desired TIME DISPLAY for CD
playback.
Each time this button is pressed, selection is as follows:
--------à EACH ----à REMAIN ----à TOTAL ------------
“EACH” : the elapsed playing time for the current track.
“REMAIN” : the remaining playing time for the current track.
“TOTAL” : the total elapsed playing time.
REPEAT button.
Press this button to listen to the music repeatedly.
First Press to repeat displayed flashing track.
Second press to repeat all of the disc.
RANDOM button.
Press this button for random order playback.
-5-
- -
7
10 KEY buttons.
A particular track may be selected for playback by using these buttons.
<EXAMPLE>
- To play track ‘ 3’, press the button ‘ 3’ once.
- To play track ‘14’, press the button “+10” once and “4”.
- To play track ‘20’, press the button “+10” twice and “0”.
INTRO
Intro scan plays the first ten seconds of each track, in the normal track order so that a
quick hearing of a CD can be made.
1 Press the Intro button “ INTRO ” appears on the display.
The first 10 seconds of each track consecutively will be played.
Normal playback may be resumed at any time by pressing the Intro button again.
REMOTE CONTROL
In the event of no remote control operation eg:- flat battery, lost remote, etc.
& looking from the front of the unit and sitting in the top right hand rear corner.
Rear panel buttons 2(Two).
Right button Open/close CD draw.
Left button Play/pause CD only.
-6-
- -
8
TROUBLESHOOTING GUIDE
Refer to the relevant sections in the manual for remedy suggestions.
SYMPTOM CHECK POINT
No sound from the CD player. CD is not selected on the amplifier.
The disc tray does not close. The disc is not loaded or seated properly into the
disc tray.
Playback does not start.
The disc is dirty.
The disc is upside down.
The player is in the PAUSE mode.
Moisture condensation has caused the unit to
operate incorrectly.
“NO DISC” appears. There is no disc loaded or the disc is loaded
incorrectly.
Playback does not start from the first track. The player is in the PROGRAM or RANDOM
mode. Press the STOP (n) button to cancel the
programme.
SPECIFICATIONS
AUDIO CHARACTERISTICS
Frequency response: 10 Hz - 20 kHz (+0.5 dB)
Signal-to-noise ratio: More than 85 dB
Wow and flutter: Below measurable limit
Channel separation: More than 80 dB
Output voltage 2 V RMS
DIGITAL SIGNAL PROCESSING
Optical pick-up: 3-beam laser
Semi-conductor laser 780 nm
D/A conversion:
∆Σ
Sampling frequency: 44.1 kHz
Power source: AC 220-230V 50/60 Hz
Fuse: 230V 500 mA Anti-surge
120V 500 mA Anti-surge
Dimension (with panel): 220 (W) x 120 (H) x 300 (D) mm
Weight: 4kg
Power consumption: 8W
-7-
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Audio Note CDT ZERO Transport Owner's Information

Catégorie
Lecteur CD
Taper
Owner's Information

dans d''autres langues