Deckorators MBC Decking Guide d'installation
- Taper
- Guide d'installation
MINERAL-BASED COMPOSITE INSTALLATION GUIDE
Items you will need
• Safety glasses
• Pencil or pen
• Tape measure
• Utility knife
• Jigsaw
• Carpenter square
(speed square)
• Power screw gun or drill
• Soft mallet
• Portable power saw
• Fine-tooth saw blades
(40-tooth minimum, sharp
carbide-tipped wood or
finish/trim blades)
• Large file or medium-grit
sandpaper
• Chalk line
• Spacing tools
• Fastener-specific tools
recommended by
manufacturer
Joist spacing requirements
Gapping requirements
•
•
16"
•
•
16"
•
•
12"
Eotek4.pdf
Standard Picture frame Diagonal (45°)
Residential 16" 16" 12"
Commercial 12" 12" 12"
Note: All dimensions are on-center.
Note: Joist spacing, stair stringer spacing and fastener requirements remain the
same for all Mineral-Based Composite deck board widths (3.5", 5.5", 7.25", and
9.25").
Installation style
Above 32º F
(0º C)
Below 32º F
(0º C)
Side-to-Side 1/8" 3/16"
End-to-End 1/16" 1/8"
End-to-Side 1/16" 1/8"
Abutting Solid
Objects 1/8" 1/4"
Installation temperature
Each variegated
Deckorators board
has a unique
appearance and
should be arranged
according to the
end user's
preference.
Almacenamiento
Mantenga cubierto antes de ser instalado.
Instalación
• Todas las tablas deben distribuirse de forma adecuada
para permitir la expansión y contracción. Refiérase a las
instrucciones para la instalación completa para detalles.
• Distribuya todo el material para terrazas a 1/4
(6.4 mm) de distancia de cualquier estructura
permanente o poste.
• Utilice como mínimo sujetadores para piso de terraza
de 2-1/2 pulg., resistentes a la corrosión, con rosca
inversa y con recubrimiento.
Espaciado de las vigas
• Espaciado de la viga 16 in (41 cm) en el centro para la
instalación perpendicular a la viga.
• Espaciado de la viga 12 in (31 cm) en el centro para la
instalación diagonal a la viga.
Visite Deckorators.com para instrucciones completas
de instalación, e información de la garantía y el cuidado
y limpieza.
Deckorators es una marca comercial de Universal Consumer Products, Inc. en
los EE.UU.
La garantía está disponible en www.deckorators.com.
Guarde las etiquetas UPC como comprobante de compra.
Rangement
Gardez couvert avant l'installation.
Installation
• Toutes les planches doivent être espacées
correctement pour permettre la dilatation et le retrait.
Consultez les directives d’installation complètes pour
obtenir les détails.
• Éloignez tout le matériau de terrasse de 6,4 mm (1/4
po) de toute structure permanente ou de tout poteau.
• Utiliser des attaches de terrasse en composite enduit,
à filetage inverse, résistantes à la corrosion de au
moins 2-1/2 po.
Espacement des solives
• Espacement aux solives de 41 cm (16 po) entre axes
pour l’installation perpendiculaire aux solives.
• Espacement des solives de 31 cm (12 po) entre axes
pour l’installation diagonale aux solives.
Visitez Deckorators.com pour les instructions complètes
d’installation, garantie et l’entretien.
Deckorators est une marque de commerce déposée de Universal Consumer
Products, Inc. aux États-Unis.
Le texte de la garantie est disponible à l’adresse www.deckorators.com.
Conservez l’étiquette d’extrémité à code UPC comme preuve d’achat.
Storage
Keep covered prior to installation.
Installation
• All boards must be spaced properly to allow for
expansion and contraction. Refer to complete
installation instructions for details.
• Space all decking material 1/4-in away from any
permanent structure or post.
• Use minimum 2-1/2" corrosion-resistant, reverse-thread,
coated composite decking fasteners.
Joist Spacing
• 16-in on-center for installation perpendicular to the joist.
• 12-in on-center for installation diagonal to the joist.
Visit Deckorators.com for complete installation
instructions, warranty and care and cleaning information.
Deckorators is a trademark of Universal Consumer Products, Inc., in the U.S.
Warranty available at www.deckorators.com.
Save UPC end tags for proof of purchase.
8560 10/15
©2014-2015 Universal Forest Products, Inc. All rights reserved.
5 Meadowcraft Parkway, Selma, AL 36701 (800) 332-5724
Chaque planche de
platelage possède
une apparence
unique et devrait
donc être
disposée au goût
de l'utilisateur.
Cada tablón tiene
una apariencia
únicay debe ser
colocado de
acuerdo a la
preferencia
del usuario final.
VAULT DECKING
•
•
16"
•
•
16"
•
•
12"
Eotek4.pdf
End Tag
Product Sticker
1X6-16' GR. DKR.
• •
12"
DeckConstr.ai
• •
16"
• •
16"
16"
••
• •
12"
DeckConstr.ai
• •
16"
• •
16"
16"
••
• •
12"
DeckConstr.ai
• •
16"
• •
16"
16"
••
SIDE
VIEW
Standard Picture frame Diagonal
TOP
VIEW
•
•
16"
•
•
16"
•
•
12"
Eotek4.pdf
Note: Always follow best
workmanship practices.
Including, but not limited to,
square cutting both board ends
prior to installation.
Each Deckorators Voyage and Vault board has a unique appearance
and should be arranged according to the end user’s preference.
Prior to construction, check with your local regulatory agency’s
code requirements. For best results, follow all installation
instructions, paying close attention to gapping, spacing and fastener
requirements.
Cutting
• 10” 40T - 80T circular blade (Carbide)
• 12” 40T - 80T circular blade (Carbide)
Installation
Fastener requirements
• Corrosion-resistant, galvanized or
stainless steel fasteners
• Reverse-thread composite screw
• Minimum of 2-1/2" long screws
• 1-1/4" minimum penetration into joist
Stair installation
• Stairs must be constructed according to national and local building
codes. Generally, building codes require 3' minimum wide treads and
11" minimum tread depth.
• 9" maximum center-to-center spacing of stringers is required.
Face screw installation
Hidden fastener installation
3/8"-1"
3/8"-1"
••
Eotek 6.pdf
16" max.
•
•
•
•
Deck board
Hidden
fastener
•
Joist
Slot
•
• Use reverse-threaded composite deck screws.
• Screws must be 3/8" to 1" from side of board,
3/8" to 1" from end of board.
• Use color-matched screws for best results.
• Use caution not to overdrive screw.
• Please refer to the compatible fastener information
on Deckorators.com/FastenerInfo.
• Fastener slots may be routed into the side of the
deck boards, as needed.
• Follow hidden fastener manufacturer’s instructions.
For Mineral-Based Composite Decking:
• Use a sharp utility knife or jigsaw to finish cuts where a circular saw
cannot fully complete cut. (Marking on the back side when needed.)
• Use a jigsaw to cut openings for protrusions. (8-12T per inch on the
blade.)
• If necessary, use a large file or medium-grit sandpaper to clean cut
edges.
• Use utility knife to cut any fibers or strands.
(In the rare event that a strand or fiber protrudes from the board, do
not pull it.) If you are using a painted blade, you can remove the paint
residue with medium grit sandpaper.
• Set power driver such that screws are slightly counter sunk.
Do not overdrive.
• If using a hidden fastener system, use the manufacturer’s
recommended fastener and follow the manufacturer’s instructions.
• Two fasteners per joist minimum.
• Ends of each board must fall on a joist.
• Double joist or use blocking where two board ends meet (fig.1).
• 1” maximum cantilever.
• Install entire deck at same temperature.
• Install the deck boards starting from the outside edge of the platform
and work toward anchor wall so that ripped pieces abut the wall. Start
installing from one end of the board and work toward the other end
of the board.
OR: Start installing from the center of the board and work out toward
the ends of the board. Do not install by fastening each end first and
working toward the middle. To keep the interior boards from mov-
ing over time, we recommend pinning the boards at the center of
their length using a #8, 2” stainless steel screw. This holds the deck
board in place at the center of each board and allows the decking to
expand/contract at the ends. Pre-drill in the groove of the deck board
with an 1/8” drill bit (fig. 2a). Drive screw into the groove so it’s flush
with the bottom of the groove (fig. 2b). This will allow you to properly
fit a Stowaway hidden fastener into the groove.
• Continue installing deck boards, adhering to the gapping
requirements. Ensure consistent appearance by aligning each
plank so that the cathedrals of the emboss pattern point in the
same direction.
NOTE: Cutting all ends of boards prior to installation recommended.
To keep gaps lined up, you must build all
sections of a split deck at the same time. This
will allow you to adjust for natural variation in
board width as you go. Snap 1 line to start the
decking then reference with a measurement
every 2 or 3 rows off that original line.
Stringer
Stair tread
Eotek2.pdf
9" max.
36" min.
5 stringers
required
11" min.
depth
1/8" min.
gap
•
•
•
•
•
•
•
•
•
Mold and mildew growth
Cleaning
fig.1
Fig.2.eps
Fig.1.eps
fig.2bfig.2a
Color variation
Like most composites, Deckorators Decking will have color varia-
tions from piece to piece. This is due to naturally occurring variations
in polymers. Purchasing all required decking material at one time is
recommended, as manufacturing runs can produce slightly different
colors. Do not install if color variation is not acceptable.
Mold and mildew can be a nuisance on any exterior building surface,
regardless of the material. If the conditions are right, they will grow on
wood, plastic, concrete, metal, and other surfaces. Mold formation
is most prevalent in consistently wet, shaded areas. Spores from the
natural environment are carried by the wind and commonly land on
decks surfaces. It is important to note that the appearance of mold/
mildew is a function of nature, not necessarily a deficiency with any of
the material on which it grows.
Periodic washing with soap/mild detergent and water will help remove
surface dirt. This will also help prevent the buildup of pollen, debris and
spores that can cause and accelerate mold/mildew growth.
Caution: A pressure washer must not be used to “blast” mold/mildew or
soils from a deck surface. The abrasive nature of the water stream can
potentially cause damage by driving the spores deeper into the material,
which may create a more challenging problem to remedy. A pressure
washer with a fan-tipped nozzle must only be used to lightly wet or rinse
wood or composite deck surfaces.
There are many deck wash and exterior cleaning products available
at retail. Only use cleaners intended for your application. Instructions
provided by the manufacturer must be followed. Some cleaning prod-
ucts and inhibitors may be more effective than others, depending on
the environmental conditions your deck issubjected to. Additionally, it is
• Stair treads should be fastened over a minimum of 5 stringers to
meet code requirements.
• 1/2" maximum tread overhang over stringers.
• 1/8" minimum gap between stair-tread boards. Local building codes
may require the gap to be increased to 1/4" - 3/8" in order to main-
tain the minimum tread depth.
always a good idea to test the cleaner in a small, inconspicuous area prior to applying it to the entire deck (www.deckorators.com).
Tips for snow removal: Care should be taken when removing snow from your deck to avoid damaging the deck surface. Use a plastic snow shovel,
one without a metal edge. A stiff push broom can work very well and minimizes lifting. Light snow can be cleared using a leaf blower. Do not attempt
to break up or scrape ice from the deck surface; use ice melt products when needed. No concerns have been reported using ice melt products la-
beled “Safe for Pets”.
Mold inhibitors
As with deck washes, there are several mold-inhibitor products available from paint stores, hardware stores, online outlets, and home centers to help
prevent long-term mold/mildew growth. For any product selected, be certain to read, understand, and follow all instructions provided by the manufac-
turer. Depending upon the environmental factors affecting your deck, some preventive cleaning products may be more effective than others. It may be
necessary to try more than one product. For ongoing preventive maintenance, follow the manufacturer’s recommendation.
Note: Deckorators is not suitable for structural use. It must not be used for primary load-bearing members such as posts, joists, beams, or stringers.
The same commonsense precautions should be taken when handling Deckorators as with wood or other building materials. Dust masks and eye pro-
tection devices are recommended to avoid possible irritation from sawdust and chips. Gloves will help protect hands.
Hands should be washed after construction work.
©2021 UFP Retail Solutions, LLC. Deckorators is a registered trademark of UFP Industries, Inc. in the U.S. All rights reserved.
5 Meadowcraft Parkway, Selma, AL 36701 800.332.5724 8529_8/21
Deckorators.com
THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR
BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED
IN THE PROJECT, INCLUDING, BUT NOT LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. UNIVERSAL FOREST PRODUCTS, INC., MAKES NO WARRANTY, EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING
CONSEQUENTIAL DAMAGES.
-
1
-
2
-
3
Deckorators MBC Decking Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Deckorators 361154 Guide d'installation
-
Deckorators Solid Decking Guide d'installation
-
-
-
-
-
-
-
-