Samsung ST40B-M Bluetooth Powered Speaker Tower Manuel utilisateur

MX-ST40B

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - ii

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

comes with important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that a safety connection to electrical

earth (ground) is not required.

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution. Consult Instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

• This product contains chemicals known to the

State of California to cause cancer and birth

defects or other reproductive harm.

• The battery (battery or batteries or battery

pack) shall not be exposed to excessive heat

such as sunshine, re or the like.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases, on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - iii

To avoid deterioration of water resistant

Check the following and use the unit correctly.

• Deformation or damage from dropping the

unit or subjecting it to mechanical shock may

cause deterioration of the water resistant.

• This unit does not have a design that is

resistant to water pressure. Use of the unit in

a location where high water pressure is

applied, such as in the shower, may cause a

malfunction.

• Do not pour high-temperature water or blow

hot air from a hair dryer or any other

applicance on the unit directly. Also never use

the unit in a place subject to high

temperatures, such as in a sauna or near a

heat source.

• Handle the cap with care. Port cover & AC

plug cover plays a very important role in

maintenance of the water resistant. When

using the unit, make sure that the cap is

closed completely. When closing the cap, be

careful not to allow foreign objects inside. If

the cap is not closed completely the water

resistant may deteriorate and may cause a

malfunction of the unit as a result of water

entering the unit.

• IPX5 cannot be met when any JACK or AC

power is plugged in.

• The product cannot be dumped to ensure it is

water resistant.

USB

(5V 0.5A)

AUX 1

POWER

ENG - iv

• The Sound Tower provides durability by IPX5.

Protection against solids IP Protection against water

0 5

No requirements X X No requirements

No protection 0 0 No protection

Solids> 50 mm 1 1 Vertically falling water

Solids> 12 mm 2 2 Vertically water-enclosure tilted 15°

Solids> 2.5 mm 3 3 Sprayed water 60° from vertical

Solids> 1.0 mm 4 4 Splashed water from all directions

Dust Protected 5 5 Hosing jets from all directions

Dust tight 6 6 Strong hosing jets from all directions

- 7 Temporary Immersion: 1m for 30 minutes

- 8 Immersion: manufacture dened depth and time

ENG - v

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the rear of your product.

Install your product horizontally, on a

suitable base (furniture), with enough space

around it for ventilation (7~10 cm). Make sure

the ventilation slots are not covered. Do not

place the unit on ampliers or other

equipment which may become hot. This unit

is designed for continuous use.

To fully turn off the unit, disconnect the AC

plug from the wall outlet. Unplug the unit if

you intend to leave it unused for a long

period of time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

CAUTION : Danger of explosion if the battery

is replaced incorrectly. Replace only with the

same or equivalent type.

Others

• As the battery is manufactured only for this

product, do not use the battery for other

electronic appliances or other purposes.

• When discarding a dead battery, put it into a

battery collection box for recycling.

• Do not disassemble the battery.

• To protect the battery, the battery cannot be

charged when the temperature is lower than

3 °C or higher than 42 °C.

• When the battery level is low, recharge it. If

the level of the battery remains low for a long

period of time, it can cause the performance

of the battery to degrade.

• Do not apply heat to the battery and do not

put the battery in a re.

• Do not disassemble the battery.

• To protect the battery, the Sound Tower may

not operate when the temperature is lower

than -17 °C or higher than 57 °C.

ENG - vi

ABOUT THIS MANUAL

The user manual has two parts: this simple paper USER MANUAL and a detailed FULL MANUAL you can

download.

USER MANUAL

See this manual for safety instructions, product installation,

components, connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on Samsung’s on-line

customer support centre by scanning the QR code on the left.

To see the manual on your PC or mobile device, download the

manual in document format from Samsung’s website.

(https://www.samsung.com/us/support/downloads/)

Design and specications are subject to change without prior notice.

ENG - vii

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control

(AAA batteries X 2) ------------------------- 2

02 Product Overview 3

Top Panel of the Sound Tower ------------------------- 3

Rear Panel of the Sound Tower ------------------------- 4

03 Connecting the Sound Tower 6

Connecting Electrical Power ------------------------- 6

How to use Audio Group ------------------------- 7

04 Connecting an External Device 13

Connecting using an Analogue Audio (AUX) Cable ------------------------- 13

Connecting a mobile device via Bluetooth ------------------------- 14

Connecting the Samsung TV via Bluetooth ------------------------- 17

05 Connecting a USB Storage Device 18

Software Update ------------------------- 19

06 Using the Remote Control 20

How to Use the Remote Control ------------------------- 20

How to use Sound Mode ------------------------- 23

How to use the DJ Effect ------------------------- 23

ENG - viii

07 Using the Samsung Sound Tower App 25

Install Samsung Sound Tower App ------------------------- 25

Launching the Samsung Sound Tower App ------------------------- 25

08 Troubleshooting 26

09 LICENCE 27

10 Open Source LICENCE Notice 28

11 Important Notes About Service 28

12 SpecicationsandGuide 29

Specications ------------------------- 29

ENG - 2

01 CHECKING THE COMPONENTS

Sound Tower Main Unit Remote Control / Batteries Power Cord

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Rear of the Sound Tower Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• When moving the product, do not drag or pull the product from the ground. Lift the product when

moving the product.

• Design and specications are subject to change without prior notice.

Inserting Batteries before using the Remote Control

(AAA batteries X 2)

Slide the battery cover in the direction of the arrow

until it is completely removed. Insert 2 AAA

batteries (1.5V) oriented so that their polarity is

correct. Slide the battery cover back into position.

ENG - 3

02 PRODUCT OVERVIEW

Top Panel of the Sound Tower

BASS

󰟻

󰟶

󰟹

󰟷

󰟸

󰟺

󰟵󰟴

󰟳

󰟳Remote

Sensor

When operating the Sound Tower system, please aim the front of the remote control at

the remote sensor.

󰟴LED Indicator

Displays operating messages or current source of the Sound Tower system.

The information sources represented by each LED are as follows:

(BT) (USB) (AUX1) (AUX2) (Power/Battery)

󰟵Power Turns the Sound Tower on and off.

󰟶Light Press the (Light) button to turn the Lighting Mode on.

󰟷Source

Press to select a source connected to the Sound Tower.

Press and hold the (Source)

button for more than 5 seconds

to enter the

“SEARCHING TV”

mode.

󰟸Play/Pause

• Play/Pause

Press the button to pause a music le temporarily.

When you press the button again, the music le plays.

• Demo play

Press and hold the

button for more than 5 seconds to start the Demo play while

the system is turned on. 5 LEDS ashing simultaneously and it plays demo music for

90seconds.

– Please be careful as it may play louder than the set volume.

󰟹Volume down Press the (Volume down) button to lower the volume.

󰟺Volume up Press the (Volume up) button to raise the volume.

󰟻BASS Press the BASS button to use the powerful bass sound.

ENG - 4

Rear Panel of the Sound Tower

USB

(5V 0.5A)

AUX 1

POWER

USB

(5V 0.5A)

AUX 1

󰟳

󰟺

󰟹 󰟸 󰟷 󰟶

󰟴 󰟵

󰟳Bluetooth

PAIRING

Press the PAIRING button to enter pairing mode, "PAIRING" LED on the rear plane

will be fast blink.

󰟴ADD STEREO Press the ADD STEREO button to connect to another same model Sound Tower

wirelessly.

󰟵GROUP PLAY Press the GROUP PLAY button to connect up to ten Sound Tower systems wirelessly.

󰟶USB Connect a USB device to the USB port on the main unit.

• Press the (Source) button to select USB.

󰟷

GROUP PLAY

OUT

Terminals

Use an Audio Cable (not supplied) to connect GROUP PLAY (OUT) terminals on the

main unit to Audio In on an external analogue output device.

󰟸GROUP PLAY

IN Terminals

Use an Audio Cable (not supplied) to connect AUX2(IN) terminals on the main unit to

Audio Out on an external analogue output device.

󰟹AUX1 Use an Audio (AUX) Cable (not supplied) to connect AUX1 jack on the main unit to

Audio Out on an external device.

󰟺Power Connect the power cord to the Power jack and connect the other end of the power

cord to a wall socket to supply electrical power to the Sound Tower.

ENG - 5

Charge LED State of the Sound Tower:

Sound

Tower state Charging state Charge LED

(AC Mode)

Charge LED

(DC Mode) Remark

Off Fully charged Off(black) Off (black)

Off Charging Green blinks N/A

Off Not in charging Off (black) Off (black) The AC cable is not

inserted.

Stand by Fully charged Blue on N/A There is no standby mode

in DC mode.

Stand by Charging Green blinks N/A

The charging LED is the

same as when Sound

Tower is shut down.

On Fully charged Blue on Blue on

When turned on, Sound

Tower mainly reects the

current battery state.

On Charging Green blinks N/A

On Not in charging and

30%~98%power Green on Green on

On Not in charging and

5% ~ 29% power Red on Red on

On Not in charging and

below 5% power Red on

Power off after

Light bar

orange blink

once

In DC mode shutdown, the entire system power will be turned off. So in the off state, compared with AC

mode, the following functions are not supported.

Feature

Wake up via bluetooth

Shop mode

Power Off Setting

Customer Reset

Power on via IR

Battery Charge

AUI on/off

UI feedback of LED lighting bar(front) on/off

ENG - 6

03 CONNECTING THE SOUND TOWER

Connecting Electrical Power

Use the power cord to connect the Sound Tower to an electrical outlet in the following order:

Connect the power cord to the Sound Tower and then to a wall socket.

See the illustrations below.

• When the AC cord is pressed in, the built-in battery will be charged automatically until the battery

is fully charged. The LED indicator on the top panel will show the current charging state

(refer to page ENG - 4).

• When you unplug the set to run on battery, the volume level drops dramatically.

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Rear of the Sound Tower)

USB

(5V 0.5A)

AUX 1

POWER

Connecting

Electrical Power

Rear of Sound Tower

ENG - 7

How to use Audio Group

You can connect multiple audio systems in a group to create a party environment and produce higher

sound output. Set one Sound Tower as the HOST and any music played on it will be shared among any

other Sound Tower systems in the Audio group.

Connecting the wired Group Play mode

1st

Sound Tower HOST

2nd

Sound Tower

Last

Sound Tower

Continue the

connection until

the last Sound

Tower

󰟳 󰟴 󰟵

Set up Group Play by connecting all the systems using audio cables (not supplied). Use the AUX or

(Source) button to change the source to AUX2 for every Sound Tower system except the 1st (or

HOST) Sound Tower system.

NOTES

• The 1st Sound Tower HOST can play music from any source.

• Depending on the length or characteristics of the cable, there may be a difference in operating

distance.

ENG - 8

Connecting the wireless Group Play mode

You can connect up to ten Sound Tower systems with the wireless Group Play function.

POWER

HOST

SUB 1 SUB 2

󰟳

󰟴 󰟵

Greenashing

󰟳 Press the GROUP PLAY button on the HOST Sound Tower system, After “GROUP LED” solw blinks

10 seconds ”GROUP PLAY”LED will be fast blink (30s).

󰟴 Press the GROUP PLAY button on the 2nd Sound Tower system (SUB 1).”GROUP PLAY”LED will be

blink.And then SUB1 will be connected with HOST,”GROUP PLAY”LED of SUB1 and HOST will stop

blinking and turn on.

󰟵 Press the GROUP PLAY button on the 3rd Sound Tower system (SUB 2). Tone prompt instead the

GROUP PLAY button on the system stops blinking.

4. If you want to add more Sound Tower systems, repeat step 3.

5. Play music on the HOST Sound Tower. Sound outputs from all the connected systems.

NOTES

• In Group play mode, “HOST” Sound Tower (Figure 1) can connect to the Samsung TV. After the

connection is successful, the Group play mode automatically exits.

• The wireless Group Play connection is available for MX-ST90B/MX-ST50B/MX-ST40B.

• Environmental conditions or other factors with connected devices may have effect on playback

quality.

• If the red LED is on the GROUP PLAY button, an error has occurred in the wireless Group Play

connection. Try step 1 to step 5 again.

• The ADD STEREO button and PAIRING button on the SUB Sound Tower systems are not available

while in wireless Group Play mode.

• The ADD STEREO button on the HOST Sound Tower system is not available while in wireless Group

Play mode.

ENG - 9

• Long press “GROUP PLAY” in BT Source state to enter Group mode as “HOST”.

• All SUB units must be connected one by one. For example, after HOST is connected, press GROUP

PLAY button on SUB 1 to connect, and after SUB 1 is connected, you should connect SUB 2 and SUB

3 one by one sequentially.

• While using Group Play, currently connected Bluetooth devices are disconnected and Bluetooth

connection is disabled.

• Bluetooth devices can search and connect with the HOST Sound Tower only.

• When in Group Play mode, the SUB cannot connect to a Bluetooth device.

• If you power off and then power on the Sound Tower or select any source other than BT on a SUB

unit, in Group Play mode, the Group Play mode is disconnected.

• This product does not support aptX audio stream with Wireless Group Play mode.

Disconnecting the wireless Group Play mode

1. Press and hold the GROUP PLAY button over 5 seconds (HOST or SUB) after Group Play is

connected or press the GROUP PLAY button (HOST or SUB) before Group Play is connected.

• Tone prompt instead and the LED above the GROUP PLAY button is off.

2. If you select any source other than BT on the SUB units or turn off the HOST Sound Tower, the

Group Play mode is disconnected.

• If the disconnection is made from the HOST Sound Tower, Group Play is disconnected.

LED Indications

LED STATE Description

Green Blink Waiting for a wireless Group Play connection.

Solid The wireless Group Play connection was successful.

Red Solid There is an error with the wireless Group Play connection.

NOTE

• In wireless connection, Playback quality can be unstable depending on Bluetooth environment.

For better play, please keep the device in wired Group Play mode.

• The rst bluetooth connection should be within 1m.

ENG - 10

Using a Smartphone and Stereo Group mode

Connect two Sound Tower and use them with your smartphone to enjoy stereo sound.

Left Sound Tower

(MAIN)

Right Sound Tower

(SUB)

󰟳 󰟴

󰟳 Press the ADD STEREO button on the left Sound Tower system. The LED blinks on the ADD

STEREO button.

󰟴 Press the ADD STEREO button on the right Sound Tower system. The LED blinks on the ADD

STEREO button.

3. When the connection is made, tone prompt. Backplane ADD LED Green Indicator Steady on.

• The MAIN Sound Tower system outputs left channel sound and the SUB Sound Tower system

outputs right channel sound. Press the ADD STEREO button on the MAIN or SUB Sound Tower

to change the sound channel of the Sound Tower.

4. Play music by connecting your smartphone to the MAIN Sound Tower and Bluetooth.

Sound is output from both Sound Tower.

NOTES

• To use the Stereo Group mode, both Sound Tower systems must be the same model.

• Environmental conditions or other factors with connected devices may have effect on playback

quality.

• If the red LED is on the ADD STEREO, an error has occured in the Stereo Group connection. Try step

1 and step 3 again.

• Remote Controller, BT PAIRING, GROUP PLAY and (Source) buttons on the SUB Sound Tower

systems are disabled while in Stereo Group mode.

• The GROUP PLAY button on the MAIN Sound Tower system is not available while in Stereo Group

mode.

ENG - 11

• In mode other than “BT” (ex. USB, AUX mode), music is played only in MAIN Sound Tower and music

is not played in SUB Sound Tower.

• The lighting colours between MAIN Sound Tower and SUB Sound Tower may vary.

• This product does not support aptX audio stream with Stereo Group mode.

• If you try to connect a Bluetooth device while Stereo Group is connecting, the Stereo Group mode

may fail.

Terminate the Stereo Group mode

Press the ADD STEREO button (MAIN or SUB) for at least 5 seconds while the Stereo Group is

connected.

• Tone prompt and the LED above the ADD STEREO button is off.

LED Indications

LED STATE Description

Green Blink Waiting for a Stereo Group connection.

Solid The Stereo Group connection is successful.

Red Solid There is an error with the Stereo Group connection.

Using Samsung TV and Stereo Group mode

Connect two Sound Tower by wire and use them with Samsung TV to enjoy stereo sound.

Left Sound Tower

(MAIN)

Right Sound Tower

(SUB)

󰟳 󰟴

󰟳 Connect the RCA cable to the AUX2 OUT on the MAIN and AUX2 IN on the SUB as shown by using

the RCA cable (not supplied).

󰟴 In “BT” mode, press the “AUX” button on the MAIN Sound Tower remote control for at least 5

seconds. The LED blinks on the ADD STEREO button.

3. When the connection is complete, the “ADD STEREO” LED turn on and then the current output.

Tone prompt instead.

ENG - 12

4. When the connection is complete, the SUB top panel “AUX2” LED turn on.

• The MAIN Sound Tower outputs the left channel sound and the SUB Sound Tower outputs the

right channel sound. Press the ADD STEREO button on the MAIN or SUB Sound Tower to

change the sound channel of the Sound Tower.

5. Connect a TV and MAIN Sound Tower via Bluetooth to play music. Sound is output from both

Sound Tower.

NOTES

• To use Stereo Group mode, both Sound Tower must be the same model.

• A red light on the LED on the ADD STEREO button indicates an error in the Stereo Group

connection. Try Step 1 to 5 again.

• In Stereo Group mode, the remote control, BT PAIRING, GROUP PLAY, and (Source) buttons on

the SUB Sound Tower are disabled.

• The GROUP PLAY button on the MAIN Sound Tower is not available in Stereo Group mode.

• If Samsung TV supports a simple connection, the connection pop-up is automatically displayed on

the TV, and if you select “Yes”, it connects to the TV. If there is a previous connection history

between Samsung TV and Sound Tower, it will be connected to Samsung TV without pop-up. For a

simple connection to Samsung TV, refer to page 17.

• The lighting colours may vary between the MAIN Sound Tower and the SUB Sound Tower.

Terminating the Stereo Group mode connection

Press the ADD STEREO button (MAIN or SUB) for at least 5 seconds after the Stereo Group is

connected.

• “OFF-STEREO MODE” tone prompt and the LED on the ADD STEREO button turns off.

ENG - 13

04 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired or wireless network to play the external device’s sound

through the Sound Tower.

Connecting using an Analogue Audio (AUX) Cable

AUX 1

- AUDIO -

R L

Mobile device / MP3 / PMP

BD / DVD player / Set-top box / Game console

󰟴

󰟳

3.5mm

stereo cable (not supplied)

Audio (AUX) Cable (not supplied)

Rear of the Sound Tower

󰟳 3.5mm stereo Cable (AUX1)

1. Connect AUX1 jack on the main unit to the AUDIO OUT jack of the Source Device using an 3.5mm

stereo cable.

2. Select “AUX1” mode by pressing the (Source) button on the top panel or on the remote control.

• You can also select a source using AUX button on the remote control.

󰟴 Audio Cable (AUX2)

1. Connect AUX2 (IN) terminals on the main unit to the AUDIO OUT terminals of the Source Device

using an audio cable.

2. Select “AUX2” mode by pressing the (Source) button on the top panel or on the remote

control.

• You can also select a source using AUX button on the remote control.

La page charge ...

Samsung ST40B-M Bluetooth Powered Speaker Tower Manuel utilisateur

Samsung ST40B-M Bluetooth Powered Speaker Tower Manuel utilisateur

dans d''autres langues

Documents connexes