Indesit XWE 101484X WSSS EU Le manuel du propriétaire

1

GB

WASHING MACHINE

Instructions for use

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Description of the washing machine, 6-7

Control panel

Display

Running a wash cycle, 8

Wash cycles and options, 9-10

Table of wash cycles

Wash options

Push & Wash

Detergents and laundry, 11-12

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13

Service, 14

XWE 101484

English,1

GB

FR

Français,15

DE

Deutsch,29

IT

Italiano,43

TR

Türkçe,57

NL

Nederlands,73

2

GB

! This instruction manual should be kept in a safe

place for future reference. If the washing machine

is sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with the

installation process.

3. Remov e t h e 4

protective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on

the rear part of the

appliance (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not

p e r f e c t l y l e v e l ,

c o m p e n s a t e f o r

any unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured in relation

to the worktop, must

not exceed 2°.

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tap using a

¾ threaded connection

(see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2 . C o n n e c t t h e

inlet hose to the

washing machine by

screwing it onto the

corresponding water

inlet of the appliance,

which is situated on

the top right-hand side

of the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

3

GB

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

Alternatively, place the

drain hose over the

edge of a washbasin

o r b a t h t u b , b y

fastening the guide

(which can be

purchased at the

technical assistance

centre) to the tap (see

figure).The free end of

the hose should not

be underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

•the socketisearthed and complies with all

applicable laws;

•thesocketisabletowithstandthemaximum

power load of the appliance as indicated in the

Technical data table (see opposite);

•thepowersupplyvoltagefallswithinthevalues

indicated in the Technical data table (see

opposite);

•the socket is compatible with the plug of

the washing machine. If this is not the case,

replace the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been installed,

the electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle

with detergent and no laundry, using the wash

cycle “Auto Clean” (see “Cleaning the washing

machine”).

65 - 100 cm

Technical data

Model

XWE 101484

Dimensions

width 59.5 cm

height 85 cm

depth 60,5 cm

Capacity

from 1 to 10 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water

connections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 71 litres

Spin speed

up to 1400 rotations per minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

Programme 8:

Cotton Standard 60°.

Programme 9:

Cotton Standard 40°.

This appliance conforms to

the following EC Directives:

- EMC - 2014/30/EU (Elec-

tromagnetic Compatibility)

- LVD - 2014/35/EU (Low

Voltage)

- 2012/19/EU (WEEE)

4

GB

Care and maintenance

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front

of the machine by

first pressing it in

the centre and then

pushing downwards

on both sides until

you can remove it

(see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figure):

a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

•Turnoffthewatertapaftereverywashcycle.

This will limit wear on the hydraulic system inside

the washing machine and help to prevent leaks.

•Unplugthewashingmachinewhencleaningit

and during all maintenance work.

Cleaning the washing machine

•Theouterpartsandrubbercomponents

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

•Thewashingmachinehasa“AutoClean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washing machine. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards

(2) (see figure).

Wash it under running

water; this procedure

should be repeated

frequently.

Caring for the door and drum of your

appliance

•Alwaysleavetheportholedoorajarinorderto

prevent unpleasant odours from forming.

2

1

2

3

A

B

5

GB

Precautions and tips

! This washing machine was designed and constructed

in accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

•Thisappliancewasdesignedfordomesticuseonly.

•Thisappliancecanbeusedbychildren

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

•Thewashingmachinemustonlybeusedbyadults,in

accordance with the instructions provided in this manual.

•Donottouchthemachinewhenbarefootorwithwetor

damp hands or feet.

•Donotpullonthepowersupplycablewhenunplugging

the appliance from the electricity socket. Hold the plug

and pull.

•Donotopenthedetergentdispenserdrawerwhilethe

machine is in operation.

•Donottouchthedrainedwaterasitmayreach

extremely high temperatures.

•Neverforcetheportholedoor.Thiscoulddamagethe

safety lock mechanism designed to prevent accidental

opening.

•Iftheappliancebreaksdown,donotunderany

circumstances access the internal mechanisms in an

attempt to repair it yourself.

•Alwayskeepchildrenwellawayfromtheappliancewhile

it is operating.

•Thedoorcanbecomequitehotduringthewashcycle.

•Iftheappliancehastobemoved,workinagroupoftwo

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

•Beforeloadinglaundryintothewashingmachine,make

sure the drum is empty.

Disposal

•Disposingofthepackagingmaterials:observelocal

regulations so that the packaging may be re-used.

• TheEuropeanDirective2012/19/EUonWaste 

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

6

GB

Description of the washing

machine

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button

and indicator light

DELAYED

START

button

OPTION

buttons

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: press this briefly to switch the

machine on or off. The START/PAUSE indicator light which

flashes slowly in a green colour shows that the machine is

switched on. To switch off the washing machine during the

wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the

machine will not switch off.

If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

PUSH & WASH button: (see “Wash cycles and options”).

WASH CYCLE SELECTOR KNOB: used to set the

desired wash cycle (see “Table of wash cycles”).

OPTION buttons: press to select the available options.

The indicator light corresponding to the selected option will

remain lit.

TEMPERATURE button: press to reduce or

completely exclude the temperature; the value appears on

the display.

SPIN button: press to reduce or completely exclude

the spin cycle; the value appears on the display.

DELAYED START button: press to set a delayed

start for the selected wash cycle; the delay period appears

on the display.

START/PAUSE button and indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the indicator

light will remain lit in a fixed manner. To pause the wash

cycle, press the button again; the indicator light will flash

in an amber colour. If the symbol is not illuminated, the

door may be opened. To start the wash cycle from the

point at which it was interrupted, press the button again.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF button briefly and

wait for the machine to start up again.

DISPLAY

PUSH & WASH

button

7

GB

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED

START option has been set, the countdown to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the

machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.

The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of

10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon

will then switch off approximately 1 minute after the final amount of time remaining has appeared.

The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle

appear in section B:

Main wash

Rinse

Spin

Drain

The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.

There are three levels in section C concerning the washing options.

DOOR LOCKED indicator light:

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door.

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened.

Display

B

C

A

C

8

GB

Running a wash cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH & WASH” button to start the wash

programme.

Traditional programming

1. SWITCH THE MACHINE ON. Press the button;

the START/PAUSE indicator light will flash slowly in a

green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

3. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle

will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modify the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again,

the maximum values are restored.

! Exception: if the 8 programme is selected, the

temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option has been

activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until

the text “OFF” appears on the display.

Modify the cycle settings.

• Pressthebuttontoenabletheoption;theindicator

light corresponding to the button will switch on.

• Pressthebuttonagaintodisabletheoption;the

indicator light will switch off.

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! If the selected option is not compatible with another

previously selected option, the indicator light will

flash accompanied by a buzzer (3 beeps), and only

the latter option will be activated; the indicator light

corresponding to the activated option will turn on.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/

PAUSE button. The corresponding indicator light will

turn green, remaining lit in a fixed manner, and the door

will be locked (the DOOR LOCKED symbol will be lit).

To change a wash cycle while it is in progress, pause

the washing machine using the START/PAUSE button

(the START/PAUSE indicator light will flash slowly in an

amber colour); then select the desired cycle and press

the START/PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press

the START/PAUSE button again to restart the wash

cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END” on the display; when the

DOOR LOCKED symbol switches off the door may

be opened. Open the door, unload the laundry and

switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

9

GB

Wash cycles and options

Table of wash cycles

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 8 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 9 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.

3) Synthetic program along: set wash cycle 10 with a temperature of 40°C.

Wash cycles

Description of the wash cycle

Max. temp.

(°C)

Max. spe-

ed (rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption

kWh

Total water lt

Cycle duration

Prewash

Wash

Fabric

softener

Bleach

Special

1

Sport

30° 600 -

 

- 4,5 - - - 60’

2

Dark

30° 800 -

 

- 6 - - - 80’

3

Anti-odour (Cotton) 60° 1000 -

 

- 4 - - - 125’

3

Anti-odour (Synthetic) 40° 1000 -

 

- 4 - - - 110’

4

Delicate

30° 0 -

 

- 1 - - - 80’

5

Wool: for wool, cashmere, etc. 40° 800 -

 

- 2,5 - - - 100’

6

Duvet: for down-stuffed garments. 30° 1000 -

 

- 3,5 - - - 105’

Standard

7

Cottons with Pre-wash: extremely soiled whites. 90° 1400

  

- 10 53 2,73 105 200’

8

Cotton Standard 60°C (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1400 -

 

- 10 53 1,08 60 220’

9

Cotton Standard 40°C (2): lightly soiled whites and delicate colours.

40° 1400 -

 

- 10 53 0,94 85 190’

10

Synthetic: heavily soiled resistant colours. 60° 800 -

 

- 5,5 48 1,20 68 125’

10

Synthetic (3): lightly soiled resistant colours. 40° 800 -

 

- 5,5 48 0,83 69 115’

11

Coloured

40° 1400 -

 

- 10 53 1,02 101 125’

Eco & Rapid

12

Cotton Standard 20°C: lightly soiled whites and delicate colours. 20° 1400 -

 

- 10 - - - 200’

13

Eco Synthetic

20° 800 -

 

- 10 - - - 125’

14

Rapid

- 800 - -



- 1,5 - - - 9’

14

Rapid

30° 800 -

 

- 4 71 0,21 50 30’

14

Rapid

60° 1000 -

 

- 10 - - - 60’

Partials

Rinse/Bleach - 1400 - -

 

10 - - - 60’

Spin + Drain - 1400 - - - - 10 - - - 10’

Drain only * - OFF - - - - 10 - - - 3’

Wash options

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! If the selected option is not compatible with another

previously selected option, the indicator light will

flash accompanied by a buzzer (3 beeps), and only

the latter option will be activated; the indicator light

corresponding to the activated option will turn on.

Rapid

When this button is pressed the first time, the 9’ icon will

light up, when pressed the second time the 30’ icon lights

up and the third time the 1h icon lights up. When pressed

the fourth time the 9’ icon lights up again.

Fast Forward

During a wash programme and under certain conditions,

pressing this button allows for ending the wash

programme after only 20’ if necessary, by performing a

brief rinse cycle followed by a spin cycle at maximum 800

rpm or lower, if reduced manually during the programme

customisation phase. In this case, washing and rinsing

performance will be reduced. After pressing the button, the

relative indicator light turns on together with the indicator

light of the rinse phase. If the selected temperature is

equal to 40° and/or the button is pressed during the initial

phase of the programme, the “Fast Forward” option lasts

longer so that the detergent can dissolve properly and

avoid damaging the fabrics. In this case, the rinse phase

indicator light flashes while the wash indicator light remains

fixed until the necessary activation conditions are fulfilled.

If less than 20’ remain of the wash programme, the option

will be disabled.

Stain removal

Thisoptionallowsforselectingthetypeofdirtsoasto

optimally adjust the cycle for removing the stains. The

following types of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages,

for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of

selected dirt.

* If you select programme and exclude the spin cycle, the machine will drain only.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

10

GB

Push & Wash

This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF

button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the

Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.

The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes

at a temperature of 30° and a maximum spin speed of 1200 rpm. Maximum load 4,5 kg. (Cycle duration 50’).

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and additives.

3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns

green and the door will lock (the DOOR LOCKED symbol turns on).

N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle

recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.

To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at

which it was interrupted.

4. Once the programme is finished, the END indicator light turns on.

11

GB

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance and

contribute to environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent

dispenser drawer and pour

in the detergent or washing

additive, as follows.

Compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

Compartment 2: Washing detergent (powder or liquid)

If liquid detergent is used, it is recommended that the

removable plastic partition A (supplied) be used for proper

dosage. If powder detergent is used, place the partition

into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indicated

on the central pin.

Extra compartment 4: Bleach

Bleach cycle

Insert the additional compartment 4 (provided) into

compartment 1. In pouring the bleach do not exceed the

“max” level indicated on the central pin.

Perform bleaching by pouring the bleach into additional

compartment 4 and set the programme .

! Traditional bleach should be used on resistant white

fabrics, and delicate bleach for coloured and synthetics

fabrics and for wool.

Preparing the laundry

• Dividethelaundryaccordingto:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Emptyallgarmentpocketsandcheckthebuttons.

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Special wash cycles

Sport (programme 1) is designed for washing lightly soiled

sports clothing (tracksuits, shorts, etc.); for best results, we

recommend not exceeding the maximum load indicated

in the “Table of wash cycles”. We recommend using liquid

detergent, and adding the amount suitable for a half-load.

Dark: use programme 2 to wash dark-coloured garments.

This programme is designed to maintain dark colours over

time. We recommend using a liquid detergent for the best

results when washing dark-coloured garments.

Anti-odour: use programme 3 for washing garments

with bad odours (e.g. smoke, sweat, fried food). The

programme is designed to remove bad odours while

preserving the fabric fibres. Synthetics fabrics or mixed

loads should be washed at 40°, and resistant cotton

fabrics at 60°.

Delicate: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments.

Wool - Woolmark Apparel Care - Blue:

the wool wash cycle of this machine has been approved

by The Woolmark Company for the washing of wool

garments labelled as “hand wash” provided that the

products are washed according to the instructions on the

garment label and those issued by the manufacturer of this

washing machine. (M1135)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Duvet: to wash double or single duvets (the weight of

which should not exceed 3,5 kg), cushions or clothes

padded with goose down such as puffa jackets, use the

special wash programme number 6. We recommend that

duvets are placed in the drum with their edges folded

inwards (see figure) and that no more than ¾ of the total

volume of the drum is used. To achieve the best results,

we recommend that a liquid detergent is used and placed

inside the detergent dispenser drawer.

Coloured: use this programme 11 to wash bright

coloured clothes. The programme is designed to maintain

bright colours over time.

12

GB

Cotton Standard 20°C (programme 12) ideal for lightly

soiled cotton loads. The effective performance levels

achieved at cold temperatures, which are comparable to

washing at 40°, are guaranteed by a mechanical action

which operates at varying speed, with repeated and

frequent peaks.

Eco Synthetic (programme 13) ideal for mixed loads

(cotton and synthetics) with a normal soil level. The

effective performance levels achieved at cold temperatures

are guaranteed by a mechanical action which operates at

varying speed, across set average intervals.

Rapid (programme 14) allows for varying the garment

treatment duration from 9’ to 1h. Pressing the

corresponding “Rapid” button allows for varying the cycle

duration between 9’ (refresh), 30’ (wash), 1h (wash).

The 9’ cycle refreshes garments using fabric softener

only; it is advisable not to add any detergent into

the machine. The 30’ programme is designed to wash

lightly soiled garments at 30° (excluding wool and silk)

with a 3 kg maximum load in a short time: it only lasts 30

minutes and allows for saving time and energy. The “1h”

cycle is designed to wash moderately soiled resistant

cotton garments at 60° in an hour, with good washing

performance. For synthetic or mixed garments, we

recommend lowering the temperature down to 40°.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs

the distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

13

GB

Troubleshooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),

make sure that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water (the text “H2O” on the

display).

The washing machine

continuously takes in and drains

water.

The washing machine does not

drain or spin.

The washing machine vibrates a

lot during the spin cycle.

The washing machine leaks.

The “option” and START/PAUSE

indicator lights flash rapidly and an

error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

Push & Wash does not activate.

The programme lasts a lot less

that expected.

Possible causes / Solutions:

•Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.

•Thereisnopowerinthehouse.

•Thewashingmachinedoorisnotclosedproperly.

•TheON/OFFbuttonhasnotbeenpressed.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thewatertaphasnotbeenopened.

•Adelayedstarthasbeenset.

•Thewaterinlethoseisnotconnectedtothetap.

•Thehoseisbent.

•Thewatertaphasnotbeenopened.

•Thereisnowatersupplyinthehouse.

•Thepressureistoolow.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor

(see “Installation”).

•Thefreeendofthehoseisunderwater(see “Installation”).

•Thewalldrainagesystemisnotfittedwithabreatherpipe.

If the problem persists even after these checks, turn off the water tap, switch the

appliance off and contact the Technical Assistance Service. If the dwelling is on one

of the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to prevent this inconvenience.

•Thewashcycledoesnotincludedraining:somecyclesrequirethedraining

process to be enabled manually.

•Thedrainhoseisbent(see “Installation”).

•Thedrainageductisclogged.

•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).

•Thewashingmachineisnotlevel(see “Installation”).

•Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).

•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).

•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care

and maintenance”).

•Thedrainhoseisnotfixedproperly(see “Installation”).

•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for

washing machines” or “hand and machine wash”, or the like).

•Toomuchdetergentwasused.

• AfterswitchingonthemachineacontrolotherthanPush&Washwasactivated.

Switch the machine off and press the Push & Wash button.

• The“FastForward”optionwasactivated.

14

GB

Service

Before contacting the Technical Assistance Service:

• Checkwhetheryoucansolvetheproblemalone(see“Troubleshooting”).

• Restartthewashcycletocheckwhethertheproblemhasbeensolved.

• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

FR

15

Français

FR

LAVE-LINGE

Sommaire

Installation, 16-17

Déballage et mise à niveau

Raccordements eau et électricité

Premier cycle de lavage

Caractéristiques techniques

Entretien et soin, 18

Coupure de l’arrivée d’eau et du courant

Nettoyage du lave-linge

Nettoyage du tiroir à produits lessiviels

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau d’arrivée de l’eau

Précautions et conseils, 19

Sécurité générale

Mise au rebut

Description du lave-linge, 20-21

Bandeau de commandes

Écran

Comment faire un cycle de lavage, 22

Programmes et options, 23-24

Tableau des programmes

Options de lavage

Push & Wash

Produits lessiviels et linge, 25-26

Tiroir à produits lessiviels

Cycle blanchissage

Triage du linge

Programmes spéciaux

Système d’équilibrage de la charge

Anomalies et remèdes, 27

Assistance, 28

XWE 101484

Mode d’emploi

16

FR

Installation

! Conserver ce mode d’emploi pour pouvoir

le consulter à tout moment. En cas de vente,

de cession ou de déménagement, veiller à

ce qu’il suive toujours le lave-linge pour que

son nouveau propriétaire soit informé sur son

mode de optionnement et puisse profiter des

conseils correspondants.

! Lire attentivement les instructions: elles

fournissent des conseils importants sur

l’installation, l’utilisation et la sécurité de

l’appareil.

Déballage et mise à niveau

Déballage

1. Déballer le lave-linge.

2. Contrôler que le lave-linge n’a pas été

endommagé pendant le transport. S’il est

abîmé, ne pas le raccorder et contacter le

vendeur.

3. Enlever les 4 vis

de protection servant

au transport, le

caoutchouc et la cale,

placés dans la partie

arrière (voir figure).

4. Boucher les trous à l’aide des bouchons

plastique fournis.

5. Conserver toutes ces pièces: il faudra les

remonter en cas de transport du lave-linge.

! Les pièces d’emballage ne sont pas des

jouets pour enfants.

Mise à niveau

1. Installer le lave-linge sur un sol plat et rigide,

sans l’appuyer contre des murs, des meubles

ou autre.

2. Si le sol n’est

pas parfaitement

horizontal, visser ou

dévisser les pieds de

réglage avant (voir

figure) pour niveler

l’appareil; son angle

d’inclinaison, mesuré

sur le plan de travail,

ne doit pas dépasser

2°.

Une bonne mise à niveau garantit la stabilité

de l’appareil et évite qu’il y ait des vibrations,

du bruit et des déplacements en cours de

optionnement. Si la machine est posée sur de

la moquette ou un tapis, régler les pieds de

manière à ce qu’il y ait suffisamment d’espace

pour assurer une bonne ventilation.

Raccordements eau et électricité

Raccordement du tuyau d’arrivée de

l’eau

1. Reliez le tuyau

d’alimentation en le

vissant à un robinet

d’eau froide à embout

fileté 3/4 (voir figure).

Faire couler l’eau

jusqu’à ce qu’elle

soit limpide et sans

impuretés avant de

raccorder.

2. Raccorder le tuyau

d’arrivée de l’eau

au lave-linge en le

vissant à la prise

d’eau prévue, dans la

partie arrière en haut

à droite (voir figure).

3. Attention à ce que le tuyau ne soit pas plié

ou écrasé.

! La pression de l’eau doit être comprise entre

les valeurs indiquées dans le tableau des

Caractéristiques techniques (voir page ci-

contre).

! Si la longueur du tuyau d’alimentation ne

suffit pas, s’adresser à un magasin spécialisé

ou à un technicien agréé.

! N’utiliser que des tuyaux neufs.

! Utiliser ceux qui sont fournis avec l’appareil.

FR

17

Raccordement du tuyau de vidange

Raccorder le tuyau

d’évacuation, sans

le plier, à un conduit

d’évacuation ou

à une évacuation

murale placés à

une distance du sol

comprise entre 65 et

100 cm ;

Autrement, accrocher

le tuyau de vidange

à un évier ou à une

baignoire, dans

ce cas, attacher

la crosse (à

acheter au service

d’assistance) au

robinet (voir figure).

L’extrémité libre du

tuyau d’évacuation

ne doit pas être plongée dans l’eau.

! L’utilisation d’un tuyau de rallonge est

absolument déconseillée mais si on ne peut

faire autrement, il faut absolument qu’il ait le

même diamètre que le tuyau original et sa

longueur ne doit pas dépasser 150 cm.

Raccordement électrique

Avant de brancher la fiche dans la prise de

courant, s’assurer que :

• lapriseestbienreliéeàlaterreetest

conforme aux réglementations en vigueur;

• lapriseestbienapteàsupporterla

puissance maximale de l’appareil indiquée

dans le tableau des Caractéristiques

techniques (voir ci-contre);

• latensiond’alimentationestbiencomprise

entre les valeurs figurant dans le tableau

des Caractéristiques techniques (voir ci-

contre);

• lapriseestbiencompatibleaveclafichedu

lave-linge. Autrement, remplacer la prise ou

la fiche.

! Le lave-linge ne doit pas être installé dehors,

même à l’abri, car il est très dangereux de le

laisser exposé à la pluie et aux orages.

! Après installation du lave-linge, la prise de

courant doit être facilement accessible.

65 - 100 cm

! N’utiliser ni rallonges ni prises multiples.

! Le câble ne doit être ni plié ni trop écrasé.

! Le câble d’alimentation ne doit être remplacé

que par des techniciens agréés.

Attention! Nous déclinons toute responsabilité

en cas de non-respect des normes

énumérées ci-dessus.

Premier cycle de lavage

Avant la première mise en service de l’appareil,

effectuer un cycle de lavage avec un produit

lessiviel mais sans linge et sélectionner

le programme «AUTO NETTOYANT» (voir

“Nettoyage du lave-linge”).

Caractéristiques techniques

Modèle

XWE 101484

Dimensions

largeur 59,5 cm

hauteur 85 cm

profondeur 60,5 cm

Capacité

de 1 à 10 kg

Raccorde-

ments élec-

triques

Voir la plaque signalétique

appliquée sur la machine

Raccor-

dements

hydrauli-

ques

pression maximale

1 MPa (10 bar)

pression minimale

0,05 MPa (0,5 bar)

capacité du tambour 71 litres

Vitesse

d’essorage

jusqu’à 1400 tours minute

Programmes

de contrôle

selon les

directives

1061/2010

et

1015/2010

programme 8;

Coton standard 60°C.

programme 9;

Coton standard 40°C.

Cet appareil est conforme

aux Directives Communau-

taires suivantes:

- EMC - 2014/30/EU (Com-

patibilité électromagnétique)

- 2012/19/EU (WEEE)

- LVD - 2014/35/EU (Basse

Tension)

18

FR

Entretien et soin

Coupure de l’arrivée d’eau et du

courant

• Fermerlerobinetdel’eauaprèschaque

lavage. Cela réduit l’usure de l’installation

hydraulique du lave-linge et évite tout

danger de fuites.

• Débrancherlafichedelaprisedecourant

lors de tout nettoyage du lave-linge et

pendant tous les travaux d’entretien.

Nettoyage du lave-linge

• Pournettoyerl’extérieuretlespartiesen

caoutchouc, utiliser un chiffon imbibé d’eau tiède

et de savon. N’utiliser ni solvants ni abrasifs.

•Celave-lingeestéquipéd’unprogramme

«AUTO NETTOYANT» des parties internes qui doit

être effectué tambour complètement vide.

La lessive (dans une quantité égale à 10% de

celle conseillée pour du linge peu sale) ou les

additifs spéciaux pour le nettoyage du lave-

linge, pourront être utilisés comme adjuvants

dans le programme de lavage. Il est conseillé

d’effectuer le programme de nettoyage tous

les 40 cycles de lavage.

Pour activer le programme, appuyer

simultanément sur les touches A et B pendant

5 secondes (voir figure). Le programme

démarrera automatiquement et durera environ

70 minutes. Pour stopper le cycle, appuyer

sur la touche START/PAUSE.

Nettoyage du tiroir à produits

lessiviels

Pour sortir le tiroir,

appuyer sur le levier (1)

et tirer vers soi (2) (voir

figure).

Le laver à l’eau

courante ; effectuer

cette opération assez

souvent.

Entretien du hublot et du tambour

•Ilfauttoujourslaisserlehublotentrouvert

pour éviter la formation de mauvaise odeurs.

2

1

Nettoyage de la pompe

Le lave-linge est équipé d’une pompe

autonettoyante qui n’exige aucune opération

d’entretien. Il peut toutefois arriver que de

menus objets (pièces de monnaie, boutons)

tombent dans la préchambre qui protège la

pompe, placée en bas de cette dernière.

! S’assurer que le cycle de lavage est bien

terminé et débrancher la fiche.

Pour accéder à cette préchambre :

1. retirer le panneau

situé à l’avant

du lave-linge en

appuyant vers le

centre. Appuyer

ensuite vers le bas

de chaque côté et

l’extraire (voir figures).

2. dévisser le

couvercle en le

tournant dans le sens

inverse des aiguilles

d’une montre (voir

figure) : il est normal

qu’un peu d’eau

s’écoule;

3. nettoyer soigneusement l’intérieur;

4. revisser le couvercle;

5. remonter le panneau en veillant à bien enfiler

les crochets dans les fentes prévues avant de

le pousser contre l’appareil.

Contrôle du tuyau d’arrivée de

l’eau

Contrôler le tuyau d’alimentation au moins

une fois par an. Procéder à son remplacement

en cas de craquèlements et de fissures : car

les fortes pressions subies pendant le lavage

pourraient provoquer des cassures.

! N’utiliser que des tuyaux neufs.

1

2

3

A

B

FR

19

Précautions et conseils

! Ce lave-linge a été conçu et fabriqué conformément

aux normes internationales de sécurité. Ces consignes

sont fournies pour des raisons de sécurité, il faut les lire

attentivement.

Sécurité générale

•Cetappareilestconçupourunusagedomestique.

•Cetappareilpeutêtreutiliséparlesenfantsà

partir de 8 ans et par les personnes dont les

capacités physiques, sensorielles ou mentales

sont réduites ou qui ne disposent pas des

connaissances suffisantes, à condition qu’ils

soient encadrés ou aient été formés de façon

appropriée pour l’utilisation de l’appareil de façon

sûre et en comprenant les dangers qui y sont liés.

Les enfants ne doivent pas jouer avec l’appareil.

L’entretien et le nettoyage ne doivent pas être

effectués par les enfants sans surveillance.

•Nejamaistoucherl’appareilsil’onestpiedsnusetsiles

mains sont mouillées ou humides.

•Nejamaistirersurlecâblepourdébrancherlafichedela

prise de courant.

•Nepasouvrirletiroiràproduitslessivielssilamachine

est branchée.

•Nepastoucheràl’eaudevidange,ellepeutatteindre

des températures très élevées.

•Nepasforcerpourouvrirlehublot:leverrouillagede

sécurité qui protège contre les ouvertures accidentelles

pourrait s’endommager.

•Encasdepanne,éviteràtoutprixd’accéderaux

mécanismes internes pour tenter une réparation.

•Veilleràcequelesenfantsnes’approchentpasde

l’appareil pendant son optionnement.

•Pendantlelavage,lehublotatendanceàseréchauffer.

•Deuxoutroispersonnessontnécessairespourdéplacer

l’appareil avec toutes les précautions nécessaires. Ne

jamais le déplacer tout seul car il est très lourd.

•Avantd’introduirelelinge,s’assurerqueletambourest

bien vide.

Mise au rebut

•Miseaurebutdumatérield’emballage:seconformer

aux réglementations locales de manière à ce que les

emballages puissent être recyclés.

•LaDirectiveEuropéenne2012/19/EU-WEEEsurles

Déchets des Equipements Electriques et Electroniques,

exige que les appareils ménagers usagés ne soient pas

jetés dans le flux normal des déchets municipaux. Les

appareils usagés doivent être collectés séparément afin

d’optimiser le taux de récupération et le recyclage des

matériaux qui les composent et réduire l’impact sur la

santé humaine et l’environnement.

Le symbole de la ‘’poubelle barrée’’ est apposée sur

tous les produits pour rappeler les obligations de

collecte séparée. Les consommateurs devront contacter

les autorités locales ou leur revendeur concernant

la démarche à suivre pour l’enlèvement de leur vieil

appareil.

20

FR

Description du lave-linge

Bandeau de commandes

Touche

TEMPÉRATURE

BOUTON

PROGRAMMES

Tiroir à produits lessiviels

Touche ON/OFF

Touche

ESSORAGE

Touche et voyant

START/PAUSE

Touche

DÉPART

DIFFÉRÉ

Touches

OPTION

Tiroir à produits lessiviels : pour charger les produits

lessiviels et les additifs (voir “Produits lessiviels et linge”).

Touche ON/OFF : appuyer brièvement sur la touche

pour allumer ou éteindre l’appareil. Le voyant vert START/

PAUSE clignotant lentement indique que la machine est

allumée. Pour éteindre le lave-linge en cours de lavage,

appuyer sur la touche pendant au moins 3 secondes de

suite ; une pression brève ou accidentelle n’entraîne pas

l’arrêt de l’appareil.

L’arrêt de l’appareil pendant un lavage annule le lavage en

cours.

Touche PUSH & WASH: (voir “Programmes et options”).

BOUTON PROGRAMMES: pour sélectionner le

programme désiré (voir “Tableau des programmes”).

Touches OPTION: pour sélectionner les options

disponibles. Le voyant correspondant à l’option

sélectionnée restera allumé.

Touche TEMPÉRATURE : appuyer sur cette

touche pour diminuer la température ou pour l’exclure

complètement. La valeur correspondante s’affiche à

l’écran.

Touche ESSORAGE : appuyer sur cette touche

pour diminuer la vitesse de l’essorage ou pour l’exclure

complètement. La valeur correspondante s’affiche à

l’écran.

Touche DÉPART DIFFÉRÉ : appuyer pour

sélectionner un départ différé pour le programme choisi. Le

retard est affiché à l’écran.

Touche et voyant START/PAUSE : quand le voyant

vert clignote lentement, appuyer sur la touche pour

démarrer un lavage. Une fois le cycle lancé, le voyant

passe à l’allumage fixe. Pour activer une pause de lavage,

appuyer à nouveau sur la touche ; le voyant devient

couleur ambre et se met à clignoter. Si le symbole

n’est pas allumé, il est possible d’ouvrir le hublot. Pour

faire redémarrer le lavage exactement à l’endroit de l’arrêt,

appuyer une nouvelle fois sur la touche.

Stand-by

Ce lave-linge, conformément aux nouvelles normes en

vigueur dans le domaine de l’économie d’énergie, est

équipée d’un système d’extinction automatique (veille)

activé après environ 30 minutes d’inutilisation. Appuyez

brièvement sur la touche ON-OFF et attendre que la

machine soit réactivée.

ECRAN

Touche

PUSH & WASH

La page charge ...

Indesit XWE 101484X WSSS EU Le manuel du propriétaire

Indesit XWE 101484X WSSS EU Le manuel du propriétaire

dans d''autres langues