Whirlpool WRT112CZJW Mode d'emploi

Marque: Whirlpool

Modèle: WRT112CZJW

Catégorie: Frigos

Taper: Mode d'emploi

Ce manuel convient également à

W11331641

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Learn More

In an effort to conserve natural resources, this refrigerator includes a condensed User Guide. A complete User Instructions manual

can be downloaded at: www.whirlpool.com/manuals. The model number is located on the inside wall of the refrigerator

compartment.

In the U.S.A.:

For assistance or service, call 1-800-253-1301.

In Canada:

For assistance or service, call 1-800-807-6777.

Para una version de estas instrucciones en español, visite www.whirlpool.com.

User Guide

Top Mount Refrigerator

WARNING:

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

 Plug into a grounded 3 prong outlet.

 Do not remove the ground prong.

 Do not use an adapter.

 Do not use an extension cord.

 Disconnect power before servicing.

 Replace all parts and panels before operating.

 Remove doors from your old refrigerator.

 Connect to a potable water supply only.

 Use a sturdy glass when dispensing ice (on some models).

 Keep flammable materials and vapors, such as gasoline, well

away from the refrigerator.

 Keep ventilation openings, in the appliance enclosure or

in the built-in structure, clear of obstruction.

 Do not use mechanical devices or other means to accelerate

the defrosting process, other than those recommended by

the manufacturer.

 Use two or more people to move and install the refrigerator.

 Disconnect the power before installing the ice maker (on ice

maker kit-ready models only).

 Use a sturdy glass when dispensing ice (on some models).

 Do not hit the refrigerator glass doors (on some models).

 Use nonflammable cleaner.

 Do not damage the refrigerant circuit.

 Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of type

recommended by the manufacturer.

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

 Children should be supervised to ensure that they do not

play with the appliance.

 If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

person in order to avoid a hazard.

 Do not store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

 This appliance is intended to be used in household and

similar applications such as:

- Staff kitchen areas in shops, offices and other working

environments;

- Farm houses and by clients in hotels, motels and other

residential type environments;

- Bed and breakfast type environments;

- Catering and similar non-retail applications.

To reduce the risk of fire, electric shock or injury to persons when using the refrigerator,

follow basic precautions, including the following:

Proper Disposal of Your Old

Refrigerator

IMPORTANT: Child entrapment and suffocation are not prob-

lems of the past. Junked or abandoned refrigerators are still

dangerous – even if they will sit for “just a few days.” If you are

getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

WARNING

Suffocation Hazard

Remove doors or lid from your old freezer or

Failure to do so can result in death or

brain damage.

refrigerator.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

IMPORTANT: Do not remove the white foam air return insert

from behind the control panel on the ceiling of the refrigerator.

If the insert is removed, ice may migrate down from the freezer

and cause icicles to form.

1. Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Rinse with warm water

and dry with a soft cloth.

NOTE: Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove tape or

glue. These products can damage the surface of your

refrigerator. For more information see “Refrigerator Safety”.

INSTALLING YOUR FREEZER

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the oor with

cardboard or hardboard to avoid oor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as oor

damage could occur.

DANGER

Explosion Hazard

Risk of re or explosion due to puncture of refrigerant

tubing.

Follow handling instructions carefully. Flammable

refrigerant used.

Install Levelers

IMPORTANT: Lay down the refrigerator ONLY to your left-hand

side (as you are looking at the front of the refrigerator) to avoid

damaging the refrigerator.

1. Locate the levelers. They are enclosed in a plastic bag inside

the crisper drawer.

2. Using two or more people, access the bottom of the

refrigerator either by tilting it rst to one side and then the

other or by laying it down on the oor to your left-hand side

as shown.

■ Tilt the refrigerator to the side enough to access the

bottom. Using a 3/8" hex driver, remove the two screws

attaching the wooden runner to the bottom of the

refrigerator. Then install a leveler to the front corner.

Repeat for the opposite side.

NOTE: The refrigerator cabinet should not touch the floor

without a leveler installed.

■ Using the packaging corner posts (left-hand side, front and

back) as a cushion, lay the refrigerator down on the floor (to

your left-hand side only) as shown in the following graphic.

NOTE: Using the packaging as a cushion will help to avoid

possible damage to the refrigerator.

■ Using a 3/8" hex driver, remove the two screws attaching

each wooden runner to the bottom of the refrigerator. Install

a leveler to each of the front corners.

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

“Refrigerator Care.”

Location Requirements

IMPORTANT: This refrigerator is designed for indoor, household

use only.

To ensure proper ventilation for your refrigerator, it is

recommended to allow a 1/2" (1.25 cm) space on each side.

Allow 1½" (3.81 cm) of space between overhead cabinets and

refrigerator top. Allow at least 1" (2.54 cm) between back of

cabinet and the wall (consider the condenser as back in case

is present). If your refrigerator has an ice maker, make sure you

leave extra space at the back for the water line connections.

If you are installing your refrigerator next to a fixed wall, leave

enough space on the hinge side to allow the door to swing open.

A. Remove runner.

B. Install leveler.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

A. Remove runner.

B. Install leveler.

C. Packaging corner post.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

NOTE: This refrigerator is intended for use in a location where

the temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity usage

and provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Electrical Requirements

Before you move your refrigerator into its final location, it is im-

portant to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 V, 60 Hz, AC only, 15 or 20 A fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension

cord.

NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the

refrigerator to the electrical source, and turn cooling on or reset

the control (Thermostat, Refrigerator or Freezer Control,

depending on the model) to the desired setting. See “Using the

Controls” in the User Instructions, User Guide, or Use & Care

Guide.

Water Supply Requirements

Read all directions before you begin.

IMPORTANT:

■ Connect to potable water supply only.

■ If you turn the refrigerator on before the water line is

connected, turn the ice maker off.

■ All installations must meet local plumbing code

requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7/16" and 1/2"

open-end wrenches or 2 adjustable wrenches, 1/4" nut driver

and drill bit, cordless drill. Gather the required tools and parts

before starting installation. Read and follow the instructions

provided with any tools listed.

NOTE: Your refrigerator dealer has a kit available with a

1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a

piercing-type or 3/16" (4.76 mm) saddle valve which reduces

water flow and clogs more easily.

Water Pressure

A cold water supply with water pressure between 30 and 120

psi (207 and 827 kPa) is required to operate the ice maker. If

you have questions about your water pressure, call a licensed,

qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa), a booster pump can be inserted

into the small tubing that goes from the cold water line to the

reverse osmosis system.

If the ice maker is still not operating properly:

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Connect the Water Supply

(on some models)

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker off to avoid excessive noise or

damage to the water valve.

Connect the Water Line

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Locate a 1/2" to 1¹⁄4" (1.27 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work. Drill on the top side of the pipe,

not the bottom. This will help keep water away from the

drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you will need.

Measure from the connection on lower left rear of refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be

sure both ends of copper tubing are cut square.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

1/2" (1.25 cm)

1" (2.54 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold

water pipe you have selected.

5. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)

drilled hole in the water pipe and that the washer is under

the pipe clamp. Tighten the packing nut. Tighten the pipe

clamp screws slowly and evenly so washer makes a

watertight seal. Do not overtighten.

6. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression

nut onto outlet end with adjustable wrench.

Do not overtighten.

7. Place the free end of the copper tubing in a container or sink

and turn on the main water supply. Flush the tubing until

water is clear. Turn off the shutoff valve on the water pipe.

Coil the copper tubing.

Connect to Refrigerator

NOTE: On kit models, attach water valve to refrigerator

according to kit instructions.

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4" (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Disconnect the tube clamp on the back of the product and

insert the copper tubing through the clamp as shown.

3. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown.

4. Tighten the compression nut. Do not overtighten. Reattach

the tube clamp and tube to the back of the cabinet.

5. Turn shutoff valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install

it in the 1/4" (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

DFE

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

A. Tube clamp

B. Copper tubing

C. Compression nut

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Refrigerator Doors

TOOLS NEEDED: 5/16" hex-head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, 5/16" open-end wrench, flat

2" putty knife.

IMPORTANT:

■ Before you begin, turn off the refrigerator control. Unplug

refrigerator or disconnect power.

■ Remove food and adjustable door or utility bins from doors.

■ If you are only removing and replacing the doors, see the

“Remove Doors and Hinges” and “Replace Doors and

Hinges” sections.

Remove Doors and Hinges

1. Unplug refrigerator or disconnect power.

2. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide support between the freezer and refrigerator

doors while the hinges are being moved. Do not depend on

the door magnets to hold the doors in place while you are

working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

4. Remove the parts for the center hinge as shown in the Center

Hinge graphic.

NOTE: Provide support between the refrigerator door and the

floor while the hinges are being moved. Do not depend on the

door magnets to hold the door in place while you are working.

5. Lift the refrigerator door free from the cabinet.

6. Remove the four screws, (two on the bottom and two on the

front) attaching the bottom hinge to the cabinet. See Bottom

Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open

in the opposite direction, follow these steps. If you are not

reversing the doors, see “Replace Doors and Hinges.”

Graphics follow these instructions.

Cabinet

1. From the top of the cabinet, remove the hinge hole plugs,

move them to the opposite side, and insert the hole plugs

into the holes from where you removed the hinge screws.

See Graphic 1-2.

2. Remove the screws lling the holes to be used for the center

hinge and install them on the opposite side.

3. Move the leveler from the bottom of the refrigerator and install

it on the opposite side.

4. Move the parts of the top hinge, center hinge and bottom

hinge to the opposite side.

Doors

1. Remove door hinge hole plug from top of freezer door. Move

to opposite side as shown. See Graphic 2.

2. Remove the door stop from the bottoms of both the freezer

and refrigerator doors and install them on the opposite side.

See Graphics 3 and 4.

Replace Doors and Hinges

NOTES:

■ Door Removal & Replacement and Door Swing Reversal

graphics may be reversed if door swing is reversed.

■ Provide additional support for the doors while the hinges are

being reinstalled. Do not depend on the door magnets to hold

the doors in place while you are working.

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

2. Assemble the parts for the center hinge as shown and

tighten all screws. See Center Hinge graphic. Replace the

freezer door.

3. Assemble the parts for the top hinge as shown. See Top

Hinge graphic. Do not tighten screws completely.

4. Align the doors so that the bottom of the freezer door

is even with the top of the refrigerator door. Tighten all

screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are

in place.

2. Plug into a grounded 3 prong outlet.

3. Reset the controls. See “Using the Control(s)” in the User

Instructions, User Guide, or Use & Care Guide.

4. Return all removable door parts to doors and food to

refrigerator.

A. 5/16" Hex-Head Hinge Screw

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

Door Hinge

Hole Plug

Cabinet Hinge

Hole Plug

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

OR REMOVAL & DOOR SWING REVERSAL (OPTIONAL)

REPLACEMENT

1-2

1-1

B A

Top Hinge

DOOR REMOVAL & DOOR SWING REVERSAL (OPTIONAL)

REPLACEMENT

A. 5/16" Hex-Head Hinge Screws

B. Top Hinge

C. Spacer

A. 5/16" Hex-Head Hinge

Screws and Washers

A. Cabinet Hinge Hole Plugs

A. Door Hinge Hole Plug

Center Hinge

Bottom Hinge

Reinstallation of Door Stops

Removal of Door Stops

A. Door Stop

B. Door Stop Screw

A. Door Stop

B. Door Stop Screw

A. Center Hinge

B. 5/16" Hex-Head Hinge Screws

A. Bottom Hinge

B. 5/16" Hex-Head Hinge Screws

C. Leveler

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Leveling and Door Adjustment

Your refrigerator has two adjustable levelers, one on each side,

at the base of the refrigerator. If your refrigerator seems unsteady

or if you want the doors to close more easily, adjust the level and

tilt of the refrigerator.

1. Turn the leveler to the left to raise that side of the refrigerator

or to the right to lower that side. It may take several turns to

level the refrigerator.

NOTE: Having someone push against the top of the refriger-

ator takes some weight off the levelers. This makes it easier

to turn the levelers.

2. Once the refrigerator is level from side to side, raise the front

levelers so that the refrigerator is tilted slightly

(approximately 1/2") downward to the rear. The doors will

close more easily and the freezer door will remain closed

whenever you close the refrigerator door.

3. Open both doors again to make sure that they close as easily

as you like. If not, tilt the refrigerator slightly more to the rear

by turning both levelers to the right. It may take several more

turns.

NOTE: To keep the refrigerator level, make the same adjust-

ment to each side.

4. Using a level, make sure the refrigerator is still level from side

to side. Readjust if necessary.

Normal Sounds

Your new refrigerator may make sounds that your old one didn’t

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal.

Hard surfaces, such as the floor, walls, and cabinets, can make

the sounds seem louder. The following describes the kinds of

sounds and what may be making them.

■ If your refrigerator is equipped with an ice maker, you will

hear a buzzing sound when the water valve opens to fill the

ice maker for each cycle.

■ Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

■ You may hear the evaporator fan motor circulating air

through the refrigerator and freezer compartments. The fan

speed may increase as you open the doors or add warm

food.

■ Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

■ Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

■ As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

■ Contraction and expansion of the inside walls may cause a

popping noise.

■ You may hear air being forced over the condenser by the

condenser fan.

■ You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATOR USE

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit air-

flow between the refrigerator and freezer sections. As shown in

the illustration, cool air enters through the bottom of the freezer

section and moves up. Most of the air then flows through the

freezer section vents and recirculates under the freezer floor. The

rest of the air enters the refrigerator section through the top vent.

NOTE: Depending on your model, the refrigerator may have

either a Normal flow or Multiflow air system.

Do not block any of these vents with food packages. If the vents

are blocked, airflow will be restricted and temperature and mois-

ture problems may occur.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Using the Controls panel

Temperature Control

Temperature Control For your

convenience, the temperature

control is preset at the factory.

When you first install your

refrigerator, make sure the control is still preset as shown

NOTE: Neither compartment will cool when the control is set to

OFF.

Adjusting the Temperature Control

If you need to adjust the temperature on either the refrigerator or

freezer compartment, use the settings listed in the chart below

as a guide.

NOTE: Except when starting the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

■ Press the Temp button to toggle among the third LED lights

which indicate the temperature setting. Reading from left to

right, the LED in the first position is the least cold. The LEDs

indicate increasingly colder settings as you continue to the

right until all third LEDs are illuminated.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm Temperature Control one

setting higher

REFRIGERATOR too warm/

too little ice

Temperature Control one

setting higher

REFRIGERATOR too cold Temperature Control one

setting lower

FREEZER too cold Temperature Control one

setting lower

Airflow Control

The Airflow control is located on the back

wall of the freezer. It regulates the amount

of air flowing between the freezer and the

refrigerator compartments.

When you plug in the refrigerator for the first

time, turn the Airflow control to the

Recommended setting.

Adjust the Airflow Control

If you want to temporarily increase the cold airflow to a specific

compartment, adjust the control.

IMPORTANT: Once the performance is achieved, return the

Airflow control to the Recommended setting to keep the

refrigerator operating at optimum efficiency.

CONDITION/REASON: ADJUSTMENT:

Heavy ice use Max

Hot room temperature Max - To maintain ice

making production rate

Large quantity of groceries Min - To quickly chill food

and beverages

Crisper Humidity Control (on some models)

You control the amount of humidity in the moisture-sealed

crisper. Depending on the produce you are storing, select the

desired Humidity Level.

Humidity Level - Min Setting

MIN (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

■ Fruit: Wash, let dry and store in refrigerator in plastic bag

or crisper. Do not wash or cut berries until they are ready to

use. Sort and keep berries in original container in crisper, or

store in a loosely closed paper bag on a refrigerator shelf.

■ Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

Humidity Level - Max Setting

MAX (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

■ Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

OPERATING YOUR REFRIGERATOR

FAST COOL

3 sec

Recommended Setting

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost

automatically. However, clean both sections about once a month

to avoid buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash painted metal exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Dry thoroughly

with a soft cloth.

4. Plug in refrigerator or reconnect power.

Vacation

If you installed an ice maker and connected it to your household

water line, turn off the water supply to the refrigerator if you will

be away from home for longer than a few days.

The following accessories are available for your refrigerator. To

order, contact us and ask for the Part Number.

In the U.S.A., visit our webpage

www.whirlpool.com/accessories or call 1-800-901-2042.

In Canada, call 1-800-807-6777.

Automatic Ice Maker (optional):

Order Part#

W11424126 - Complete Icemaker kit made up of next 3 parts

W11416492 - Icemaker kit ONLY. this includes the accessory

bag for installation of IM

W11403893 - Ice Pan

W11403892 - Wire Shelf

Affresh

Kitchen & Appliance Cleaner:

Order Part #W10355010

ACCESSORIES

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

PROBLEM SOLVER

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and scan the code there with your mobile device, or visit

www.whirlpool.com/product_help. In Canada, visit http://www.whirlpool.ca.

In the U.S.A.: In Canada:

Whirlpool Brand Home Appliances Whirlpool Brand Home Appliances

Customer eXperience Center Customer eXperience Centre

553 Benson Road 200 – 6750 Century Ave.

Benton Harbor, MI 49022-2692 Mississauga ON L5N 0B7

Please include a daytime phone number in your correspondence.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

DANGER

Explosion Hazard

Risk of fire or explosion. Flammable refrigerant used.

Do not use mechanical devices to defrost refrigerator.

Do not puncture refrigerant tubing.

DANGER

Explosion Hazard

Risk of re or explosion due to puncture of refrigerant

tubing.

Follow handling instructions carefully. Flammable

refrigerant used.

If you

experience

Possible Causes and/or Recommended Solutions

The refrigerator

will not operate

■ Not connected to an electrical supply - Plug the power cord into a grounded 3-prong outlet. Do not use an

extension cord.

■ No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

■ Household fuse blown or circuit breaker tripped - Replace the fuse or reset the circuit breaker. If the

problem continues, contact an electrician.

■ Control is not turned on - Turn on the refrigerator control. See “Using the Controls.”

■ New Installation - Allow 24 hours following installation for the refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting will not cool the refrigerator more quickly.

The motor

seems to run

too much

Your new refrigerator may run longer than your old one. Energy efficient refrigerators run longer at lower, more

energy efficient speeds. Your refrigerator may run even longer if the room is warm, a large food load is added, the

door is opened often, or if the door has been left open.

The refrigerator

is noisy

Refrigerator noise has been reduced over the years. Due to this reduction in operating noise, you may notice

unfamiliar noises that are normal. Following are some normal sounds with an explanation:

■ Buzzing - heard when the water valve opens to fill the ice maker

■ Clicking/Snapping - valves opening or closing

■ Pulsating - fans/compressor adjusting to optimize performance

■ Rattling - fl w of refrigerant, water line, or from items placed on top of the refrigerator

■ Sizzling/Gurgling - water dripping on the heater during defrost cycle

■ Popping - contraction/expansion of inside walls, especially during initial cool-down

■ Water running - may be heard when ice melts during the defrost cycle and water runs into the drain pan

■ Creaking/Cracking - occurs as ice is being ejected from the ice maker mold.

The door will

not close

completely

■ The door is blocked open - Move food packages away from door. Push bin or shelf back in the correct

position. Make sure the crisper cover is fully pushed in, so that the back rests on the supports.

The door is

difficult to open

■ Gaskets are dirty or sticky - Clean gaskets and contact surfaces with mild soap and warm water. Rinse and

dry with soft cloth.

Temperature is

too warm

■ New Installation - Allow 24 hours following installation for the refrigerator to cool completely.

■ Door(s) opened often or not closed completely - Allows warm air to enter refrigerator. Minimize door

openings and keep doors fully closed.

■ A large amount of warm food has been recently added - Allow several hours for refrigerator to return to

normal temperature.

■ Check that the Temperature Control(s) are set correctly for the surrounding conditions - Adjust the

controls to one setting colder. Check temperature in 24 hours. See “Using the Controls.”

There is interior

moisture

buildup

NOTE: Some

moisture build-

up is normal.

■ Humid room - Contributes to moisture buildup in the refrigerator.

■ Door(s) opened often or not closed completely - Allows humid air to enter the refrigerator. Minimize door

openings and keep door fully closed.

The ice maker

is not

producing ice

or not enough

ice

■ The ice maker is not connected to a water supply - Connect refrigerator to water supply and turn water

shutoff valve fully open.

■ A kink in the line can reduce water fl w - Straighten the water source line.

■ Ice maker is not turned on - Make sure the ice maker wire shutoff arm or switch (depending on model) is in

the ON position.

■ New installation - Wait 24 hours after ice maker installation for ice production to begin. Wait 3 days for full

ice production.

■ Large amount of ice recently removed - Allow sufficient time or ice maker to produce more ice.

■ Ice cube jammed in the ice maker ejector arm - Remove ice from the ejector arm with a plastic utensil.

■ A reverse osmosis water filtration system connected to our cold water supply can decrease water

pressure - See “Water Supply Requirements.”

The ice cubes

are hollow or

small

NOTE: This is

an indication

of low water

pressure.

■ The water valve is not completely open - Completely open the water shutoff valve.

■ A kink in the line can reduce water flow - Straighten the water source line.

■ A reverse osmosis water filtration system connected to our cold water supply can decrease water

pressure - See “Water Supply Requirements.”

■ If questions regarding water pressure remain, call a licensed, qualified plumber.

Off-taste, odor

or gray color in

the ice

■ New plumbing connections can cause discolored or off-flavored ice - Discard the ice and wash the

ice storage bin. Allow 24 hours for the ice maker to make new ice, and discard the first 3 batches of ice

produced

■ Ice stored too long can develop an off-taste - Discard ice. Wash ice bin. Allow 24 hours for ice maker to

make new ice.

■ Food odor transferring to ice - Use airtight, moisture proof packaging to store food.

■ There are minerals (such as sulfur) in the water - A water filter my need to be installed to remove the

minerals.

03/17

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without

service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit producthelp.whirlpool.com.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and Canada, direct all requests for

warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.

WHIRLPOOL

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address, and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase, including dealer or retailer name and address

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For one year from the date of purchase,

when this major appliance is installed,

operated, and maintained according

to instructions attached to or furnished

with the product, Whirlpool Corporation

or Whirlpool Canada LP (hereafter

“Whirlpool”) will pay for factory

speciﬁed replacement parts and repair

labor to correct defects in materials or

workmanship that existed when this

major appliance was purchased or, at

its sole discretion, replace the product.

In the event of product replacement,

your appliance will be warranted for

the remaining term of the original unit’s

warranty period.

YOUR SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT

REPAIR AS PROVIDED HEREIN.

Service must be provided by a

Whirlpool designated service company.

This limited warranty is valid only in

the United States or Canada and

applies only when the major appliance

is used in the country in which it was

purchased. This limited warranty is

effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain

service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user, operator,

or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in accordance with

electrical or plumbing codes, or correction of household electrical or plumbing (e.g., house wiring,

fuses, or water inlet hoses).

4. Consumable parts (e.g., light bulbs, batteries, air or water ﬁlters, preservation solutions).

5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.

6. Conversion of products from natural gas or propane gas.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use with products not approved

by Whirlpool.

8. Repairs to parts or systems to correct product damage or defects caused by unauthorized service,

alteration, or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance ﬁnishes,

unless such damage results from defects in materials and workmanship and is reported to Whirlpool

within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive environments including,

but not limited to, high salt concentrations, high moisture or humidity, or exposure to chemicals.

11. Food or medicine loss due to product failure.

12. Pickup or delivery. This product is intended for in-home repair.

13. Travel or transportation expenses for service in remote locations where an authorized Whirlpool

servicer is not available.

14. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (e.g., trim, decorative panels,

ﬂooring, cabinetry, islands, countertops, drywall) that interfere with servicing, removal, or replacement

of the product.

15. Service or parts for appliances with original model/serial numbers removed, altered, or not easily

determined.

The cost of repair or replacement under these excluded circumstances shall be borne by

the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you. This warranty gives you speciﬁc

legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,

you should ask Whirlpool or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES: EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of

incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc legal rights, and you

also may have other rights that vary from state to state or province to province.

Afin de conserver les ressources naturelles, ce réfrigérateur comprend un guide d’utilisation rapide. L’utilisateur trouvera un manuel

d’instructions complet téléchargeable au www.whirlpool.com/manuals. Le numéro de modèle se trouve sur la paroi interne du

compartiment de réfrigération.

Aux États-Unis:

Pour l’assistance ou le service, composez le 1800253-1301.

Enregistrer votre réfrigérateur au www.whirlpool.com.

Au Canada:

Pour l’assistance ou le service, composez le 1800807-6777.

Enregistrer votre réfrigérateur au www.whirlpool.com.

Para una versión de estas instrucciones en español, visite www.whirlpool.com.

Guide d’utilisation

Réfrigérateur à congélateur supérieur

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

Mise au rebut du vieux réfrigérateur

IMPORTANT: Le risque qu’un enfant puisse se retrouver coincé

et suffoquer n’est pas chose du passé. Les réfrigérateurs jetés

ou abandonnés restent dangereux, même s’ils ne restent à

l’extérieur que pour «quelques jours». Si l’ancien réfrigérateur

doit être mis au rebut, suivre les instructions suivantes afin

d’éviter les accidents.

Avant de jeter l’ancien réfrigérateur ou

congélateur:

■ Enlever les portes.

■ Laisser les tablettes en place de sorte que les enfants ne

puissent pas y pénétrer facilement.

AVERTISSEMENT

Risque de suffoquer

Enlever les portes ou le couvercle de votre vieux

congélateur ou réfrigérateur.

Le non-respect de cette instruction peut causer

un décès ou des lésions cérébrales.

Renseignements importants à propos de la mise au

rebut des fluides réfrigérants :

Mettre le réfrigérateur au rebut conformément à la

réglementation fédérale et locale. Les fluides réfrigérants

doivent être évacués par un technicien certifié et agréé par

l’EPA conformément aux procédures établies.

AVERTISSEMENT :

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

CONSERVER CES INSTRUCTIONS

 Brancher l’appareil sur une prise à 3 alvéoles reliée à la terre.

 Ne pas enlever la broche de liaison à la terre.

 Ne pas utiliser d’adaptateur.

 Ne pas utiliser de rallonge.

 Déconnecter la source de courant électrique avant l’entretien.

 Replacer pièces et panneaux avant de faire la mise en marche.

 Enlever les portes de votre ancien réfrigérateur.

 Raccorder à la canalisation d’arrivée d’eau potable

uniquement.

 Utiliser un verre robuste pour prendre des glaçons

(sur certains modèles).

 Garder les matières et les vapeurs inflammables, telles que

l’essence, bien à l’écart du réfrigérateur.

 Garder les évents à l’intérieur de l’enceinte de l’appareil

ou de la structure encastrée exempte d’obstacles.

 Ne pas utiliser des appareils mécaniques ou autres moyens

pour accélérer le processus de dégivrage, autre que ceux

recommandés par le fabricant.

 Au moins deux personnes sont requises pour déplacer et

installer le réfrigérateur.

 Débrancher la source de courant électrique avant d’installer la

machine à glaçons (sur les modèles avec machine à glaçons

prête-à-installée uniquement).

 Utiliser un verre robuste pour prendre des glaçons

(sur certains modèles).

 Ne pas heurter les portes en verre du réfrigérateur

(sur certains modèles).

 Utiliser un produit de nettoyage ininflammable.

 Ne pas endommager le circuit réfrigérant.

 Ne pas utiliser des appareils électriques à l’intérieur des

compartiments d’aliments de l’appareil, à moins qu’ils

soient de type recommandé par le fabricant.

 Cet appareil ne convient pas à une utilisation par des

personnes (y compris des enfants) à capacités physiques,

sensorielles ou mentales réduites, ou possédant un

manque d’expérience et de connaissances, à moins

qu’elles ne soient placées sous supervision ou qu’elles

aient reçu des instructions concernant l’utilisation de

l’appareil par une personne responsable de leur sécurité.

 Les enfants doivent être surveillés afin de s’assurer

qu’ils ne jouent pas avec l’appareil.

 Si le cordon d’alimentation est endommagé, il doit être

remplacé par le fabricant, son agent de réparation ou toute

autre personne qualifiée afin d’éviter tout danger.

 Ne pas entreposer de substances explosives comme des

aérosols avec agent propulseur inflammable dans cet

appareil.

 Cet appareil est destiné à un usage domestique et à

d’autres usages similaires comme :

- espace de cuisine pour personnel de boutiques,

bureaux et autres environnements professionnels;

- résidences fermières et utilisation par les clients d’hôtels,

de motels et d’autres types de résidences;

- environnements de type chambres d’hôtes;

- Banquets et autres utilisations non commerciales

semblables.

Afin de réduire le risque d’incendie, de décharge électrique ou de blessures corporelles lors de

l’utilisation du réfrigérateur, il convient d’observer certaines précautions fondamentales, notamment :

INSTRUCTIONS D’INSTALLATION

Déballage du réfrigérateur

Retrait des matériaux d’emballage

IMPORTANT: Ne pas enlever l’encart en mousse blanche du

retour d’air situé derrière le tableau de commande, au plafond du

réfrigérateur. Si l’encart est enlevé, de la glace peut se former en

provenance du congélateur et causer la formation de glaçons.

1. Enlever tout résidu de ruban adhésif et de colle des surfaces

avant de mettre en marche votre tiroir de réfrigération.

Frotterune petite quantité de savon liquide à vaisselle

surl’adhésif avec les doigts. Rincer à l’eau tiède et

sécheravec un chiffon doux.

REMARQUE: Ne pas utiliser d’instruments coupants,

d’alcool à friction, de liquides inflammables ou de

nettoyants abrasifs pour enlever le ruban adhésif ou la

colle. Cesproduits peuvent endommager la surface du

réfrigérateur. Pour plus de renseignements, voir la section

«Sécurité du réfrigérateur».

Déplacement de votre réfrigérateur :

Votre réfrigérateur est lourd. Lors du déplacement de votre

réfrigérateur pour le nettoyage ou un entretien ou réparation,

veiller à recouvrir le plancher avec du carton ou un panneau

de fibres dures pour éviter qu'il ne subisse tout dommage.

Toujours tirer le réfrigérateur tout droit lors de son

déplacement. Ne pas incliner le réfrigérateur d’un côté ou de

l’autre ni le “faire marcher” en essayant de le déplacer car le

plancher pourrait être endommagé.

DANGER

Risque d'explosion

Risque d'incendie ou d'explosion en cas de perforation

des conduits de réfrigérant.

Suivre les instruction de manipulation avec attention.

réfrigérant utilisé inammable.

AVERTISSEMENT

Risque du poids excessif

Utiliser deux ou plus de personnes pour déplacer et

installer le réfrigérateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Installation des dispositifs de nivellement

IMPORTANT: Afin d’éviter d’endommager le réfrigérateur,

lefaire reposer UNIQUEMENT sur le côté gauche (lorsqu’on

faitface à l’avant de l’appareil).

1. Repérer l’emplacement des dispositifs de nivellement.

Ils se trouvent dans un sac en plastique situé dans le

tiroiràlégumes.

2. À l’aide d’au moins deux personnes, accéder à la partie

inférieure de l’appareil en l’inclinant d’un côté puis de l’autre

OU en le faisant reposer sur le sol sur son côté gauche,

comme illustré.

■ Incliner suffisamment le réfrigérateur sur le côté pour

pouvoir accéder à sa partie inférieure. À l’aide d’un

tourne-écrou de 3/8 po, retirer les deux vis fixant le

profilé de bois au bas du réfrigérateur. Installer ensuite

un dispositif de nivellement sur l’angle avant. Répéter

l’opération de l’autre côté.

REMARQUE: On ne doit pas laisser la caisse du

réfrigérateur toucher le plancher lorsqu’un dispositif

denivellement est installé.

■ En utilisant les cornières de l’emballage comme protection

(cornières de gauche, avant et arrière), faire reposer le

réfrigérateur sur le plancher (uniquement sur son côté

gauche), comme indiqué à l’illustration suivante.

REMARQUE: Utiliser l’emballage comme protection

permettra d’éviter d’éventuels dommages sur le réfrigérateur.

■ À l’aide d’un tourne-écrou de 3/8po, retirer les deux vis

fixant chaque profilé de bois au bas du réfrigérateur. Installer

un dispositif de nivellement sur chaque angle avant.

Nettoyage avant utilisation

Après avoir enlevé tous les matériaux d’emballage, nettoyer

l’intérieur du réfrigérateur avant de l’utiliser. Voir les instructions

de nettoyage dans la section «Entretien du réfrigérateur».

Exigences d’emplacement

IMPORTANT: Ce réfrigérateur est conçu pour un usage

domestique, à l’intérieur uniquement.

Pour obtenir une aération appropriée pour votre réfrigérateur,

ilest recommandé de laisser un espace de 1/2po (1,25cm) de

chaque côté. Laisser un espace de 1 ½po (3,81cm) entre le

dessus du réfrigérateur et le dessous des armoires. Laisser un

espace d’au moins 1po (2,54cm) entre l’arrière de l’appareil

et le mur (le condensateur représente l’arrière, s’il est présent).

Sile réfrigérateur comporte une machine à glaçons, s’assurer de

laisser un espace additionnel à l’arrière pour les raccordements

du conduit d’eau. Si on installe le réfrigérateur près d’un mur

fixe, laisser suffisamment d’espace du côté de la charnière

pourpermettre à la porte de s’ouvrir.

A. Ôter le dispositif de nivellement.

B. Installer le dispositif de nivellement.

Importants renseignements à savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

l’eau tiède quand ils sont froids. Les tablettes et les

couvercles peuvent se briser s'ils sont exposés à des

changements soudains de température ou à un impact tel

que coup brusque. Le verre trempé est conçu pour éclater

en d’innombrables pièces minuscules. Ceci est normal. Les

tablettes et les couvercles en verre sont lourds. Les saisir à

deux mains lors de leur dépose afin d'éviter de les faire

tomber.

Risque d'explosion

Garder les matériaux et les vapeurs inflammables, telle

que l'essence, loin du réfrigérateur.

Le non-respect de cette instruction peut causer

un décès, une explosion ou un incendie.

AVERTISSEMENT

A. Ôter le dispositif de nivellement.

B. Installer le dispositif de nivellement.

C. Cornière d’emballage.

REMARQUE: Ce réfrigérateur est conçu pour être utilisé dans

un endroit où la température est comprise entre un minimum de

55°F (13°C) et un maximum de 110°F (43°C). La plage de

température ambiante idéale pour un rendement optimal est

comprise entre 60°F (15°C) et 90°F (32°C). Respecter cette

plage de température permet aussi de réduire la consommation

d’électricité et d’optimiser l’efficacité du refroidissement. Il est

recommandé de ne pas installer le réfrigérateur près d’une

source de chaleur comme un four ou un radiateur.

Spécifications électriques

Avant de placer le réfrigérateur à son emplacement final, ilest

important de s’assurer d’avoir le raccordement électrique

approprié.

Méthode recommandée de liaison à la terre

Un circuit de 115V CA à 60Hz relié à la terre et protégé par un

fusible de 15A ou 20A est requis. Il est recommandé d’utiliser

un circuit distinct pour alimenter le réfrigérateur uniquement.

Utiliser une prise de courant dont l’alimentation ne peut pas être

interrompue par un interrupteur. Ne pas utiliser de rallonge.

REMARQUE: Avant d’installer ou de nettoyer un quelconque

élément, ou de remplacer une ampoule d’éclairage, désactiver

le refroidissement ou placer la commande (du thermostat,

réfrigérateur ou congélateur selon le modèle) à OFF (arrêt) et

débrancher ensuite le réfrigérateur de la source d’alimentation

électrique. Lorsque vous avez terminé, reconnecter le réfrigérateur

à la source d’alimentation électrique et réactiver le refroidissement

ou replacer la commande (du thermostat, réfrigérateur ou

congélateur selon le modèle) au réglage désiré. Voir la section

«Utilisation des commandes» dans les instructions d’utilisation,

le guide d’utilisation ou le guide d’utilisation et d’entretien.

Spécifications de l’alimentation en eau

Lire toutes les instructions avant de commencer.

IMPORTANT:

■ Brancher sur une alimentation en eau potable uniquement.

■ Si on doit mettre en marche le réfrigérateur avant que la

canalisation d’eau ne soit connectée, placer la machine à

glaçons à Off (arrêt).

■ Toutes les installations doivent être conformes aux exigences

des codes locaux de plomberie.

■ Utiliser un tuyau en cuivre et vérifier qu’il n’y a pas de

fuite. Installer seulement des tuyaux en cuivre là où les

températures resteront au-dessus du point de congélation.

OUTILS REQUIS: Tournevis à lame plate, clés plates de 7/16 po

et 1/2po ou deux clés à molette, tourne-écrou de 1/4po et foret,

une perceuse sans fil. Rassembler les outils et pièces nécessaires

avant d’entreprendre l’installation. Lire et observer les instructions

d’installation fournies avec chaque outil mentionné dans la liste.

REMARQUE: Votre marchand de réfrigérateurs propose une trousse

avec un robinet d’arrêt à étrier de 1/4po (6,35mm), un raccord et

un tube en cuivre. Avant d’en faire l’achat, s’assurer que le robinet

d’arrêt à étrier est conforme aux codes locaux de plomberie. Ne pas

employer de robinet d’arrêt à étrier de 3/16po (4,76mm) ou de type

à percer – ils réduisent le débit d’eau et s’obstruent plus facilement.

Pression d’eau

Une alimentation en eau froide avec une pression entre 30 et

120 psi (207 à 827kPa) est nécessaire pour faire fonctionner la

machine à glaçons. Pour toute question au sujet de la pression

de l’eau, faire appel à un plombier qualifié agréé.

Alimentation en eau par osmose inverse

Si un système de filtration de l’eau par osmose inverse est raccordé

à votre alimentation en eau froide, la pression de l’eau au système

doit être d’un minimum de 40 à 60lb/po² (276 à 414kPa).

Si la pression de l’eau au système d’osmose inverse est inférieure

à une valeur entre 40 à 60lb/po² (276 à 414kPa), une pompe

de surpression peut être insérée sur le petit tuyau qui va de la

canalisation d’eau froide à l’entrée du système d’osmose inverse.

Si la machine à glaçons ne fonctionne toujours pas correctement:

■ Vérifier que le filtre à sédiment dans le système à osmose

inverse n’est pas obstrué. Remplacer le filtre si nécessaire.

■ Laisser le réservoir du système d’osmose inverse se remplir

après une utilisation intense.

Pour toute question au sujet de la pression de l’eau, faire appel à

un plombier qualifié agréé.

Raccordement à la canalisation d’eau

(sur certains modèles)

Lire toutes les instructions avant de commencer.

IMPORTANT: Si l’on met en marche le réfrigérateur avant que la

canalisation d’eau ne soit raccordée, éteindre la machine à glaçons

pour éviter tout bruit excessif ou éviter d’endommager le robinet d’eau.

Raccordement à la canalisation d’eau

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Couper l’alimentation principale en eau. Ouvrir le robinet le

plus proche assez longtemps pour vider l’eau du tuyau.

3. Identier une canalisation d’eau froide verticale de 1/2po à

1¹/

4po (1,27cm à 3,18cm) à proximité du réfrigérateur.

IMPORTANT:

■ Vérifier qu’il s’agit d’une canalisation d’eau froide.

■ On peut aussi utiliser une canalisation horizontale. Percer

par le dessus de la canalisation et non pas par le dessous.

Ceci permet de tenir la perceuse à l’écart de l’eau et

d’empêcher les sédiments qu’on trouve normalement

dans l’eau de s’accumuler dans le robinet d’arrêt.

AVERTISSEMENT

Risque de choc électrique

Brancher sur une prise à 3 alvéoles reliée à la terre.

Ne pas enlever la broche de liaison à la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un câble de rallonge.

Le non-respect de ces instructions peut causer

un décès, un incendie ou un choc électrique.

Ne pas utiliser pour le filtrage d'une eau

microbiologiquement polluée ou de qualité inconnue en

l'absence d'un dispositif de désinfection adéquat avant ou

après le système. Les systèmes certifiés pour la réduction

de kyste peuvent être utilisés pour l'eau désinfectée qui

peut contenir des kystes filtrables.

1/2po (1,25cm)

1po (2,54cm)

4. Déterminer la longueur de tube de cuivre à utiliser. Mesurer

depuis le point de connexion (angle inférieur arrière gauche

du réfrigérateur) et la canalisation d’eau. Ajouter 7pi (2,1m)

pour permettre les opérations de nettoyage. Utiliser un tube

en cuivre de 1/4po (6,35mm) de diamètre extérieur. Veiller à

ce que le tube soit coupé d’équerre aux deux extrémités.

À l’aide d’une perceuse sans fil, percer un trou de 1/4 po

(6,35mm) dans la canalisation d’eau froide sélectionnée.

5. Fixer le robinet d’arrêt sur la canalisation d’eau froide avec

la bride de tuyau. Veiller à bien insérer l’extrémité de sortie

dans le trou de 1/4 po (6,35mm) de la canalisation d’eau;

veiller à placer correctement le joint sous la bride du tuyau.

Serrer l’écrou de serrage. Serrer lentement et uniformément

les vis fixant la bride de tuyau sur le tuyau afin d’assurer

l’étanchéité du joint. Ne pas serrer excessivement.

Enfiler la bague et l’écrou de compression sur le tube en

cuivre comme illustré. Insérer l’extrémité du tube directement

dans l’extrémité de sortie, aussi loin que possible. Visser

l’écrou de compression sur l’extrémité de sortie du raccord

àl’aide d’une clé à molette. Ne pas serrer excessivement.

Placer le bout libre du tube de cuivre dans un contenant ou évier

et ouvrir le robinet principal d’alimentation en eau. Laisser l’eau

s’écouler par le tube jusqu’à ce qu’elle soit limpide. Fermer le

robinet d’arrêt de la canalisation d’eau. Lover le tube de cuivre.

Raccordement au réfrigérateur

REMARQUE: Pour les modèles en kit, installer la valve d’entrée

d’eau sur le réfrigérateur conformément aux instructions du kit.

Style1

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Raccorder le tube de cuivre au robinet d’arrivée d’eau à l’aide

d’un écrou et d’une bague de compression, comme illustré.

Serrer l’écrou de compression. Ne pas serrer excessivement.

3. Utiliser la bride du tube à l’arrière du réfrigérateur pour xer le tube

au réfrigérateur comme illustré. Ceci aide à éviter d’endommager

le tube lorsque le réfrigérateur est poussé contre le mur.

4. OUVRIR le robinet d’arrêt.

5. Vérier qu’il n’y a pas de fuites. Serrer tous les raccords

(ycompris les raccords du robinet) ou les écrous qui

présentent des fuites.

6. La machine à glaçons comporte un ltre à eau incorporé.

Si les caractéristiques de l’eau requièrent un second ltre à

eau, installer celui-ci dans la canalisation d’eau de 1/4po

(6,35mm) à l’une ou l’autre des extrémités de la canalisation.

Se procurer un ltre à eau auprès de votre revendeur

d’appareils ménagers le plus proche.

Style2

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Déconnecter la bride du tube à l’arrière du produit et

introduire le tube en cuivre dans la bride, comme indiqué.

3. Raccorder le tube de cuivre au robinet d’arrivée d’eau à

l’aide d’un écrou et d’une bague de compression, comme

illustré.

4. Serrer l’écrou de compression. Ne pas serrer excessivement.

Réattacher la bride du tube et le tube à l’arrière de l’appareil.

5. OUVRIR le robinet d’arrêt. Vérier qu’il n’y a pas de fuites.

Serrer tous les raccords (y compris les raccords du robinet)

ou les écrous qui présentent des fuites.

6. La machine à glaçons comporte un ltre à eau incorporé.

Si les caractéristiques de l’eau requièrent un second ltre à

eau, installer celui-ci dans la canalisation d’eau de 1/4po

(6,35mm) à l’une ou l’autre des extrémités de la canalisation.

Se procurer un ltre à eau auprès de votre revendeur

d’appareils ménagers le plus proche.

Terminer l’installation

1. Brancher l’appareil sur une prise à 3 alvéoles reliée à la terre.

REMARQUE: Prévoir un délai de 24 heures pour la production

du premier lot de glaçons. Jeter les trois premiers lots de

glaçons produits. Prévoir un délai de 3 jours pour le remplissage

complet du récipient à glaçons.

DFE

A. Canalisation d’eau froide

B. Bride de tuyau

C. Tube de cuivre

D. Écrou de compression

E. Bague de compression

F. Robinet d’arrêt

G. Écrou de garniture

A. Bride du tube

B. Vis de bride de tube

C. Tube de cuivre

D. Écrou de compression

E. Robinet d’arrivée d’eau

A. Bride du tube

B. Tube de cuivre

C. Écrou à compression

AVERTISSEMENT

Risque de choc électrique

Brancher sur une prise à 3 alvéoles reliée à la terre.

Ne pas enlever la broche de liaison à la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un câble de rallonge.

Le non-respect de ces instructions peut causer

un décès, un incendie ou un choc électrique.

La page charge ...

Whirlpool WRT112CZJW Mode d'emploi

Marque: Whirlpool

Modèle: WRT112CZJW

Catégorie: Frigos

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WRT112CZJW User guide

Whirlpool WRT112CZJW Mode d'emploi

Ce manuel convient également à

Whirlpool WRT112CZJW Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents