Whirlpool WEE510SAGB Mode d'emploi

Catégorie
Cuisinières
Taper
Mode d'emploi
ELECTRIC RANGE
USER INSTRUCTIONS
THANK YOU for purchasing this high-quality product.
For future reference, please make a note of your product model and serial numbers. These can be found on the label
located on the upper-right corner of the front frame.
Model Number _______________________________________ Serial Number ________________________________________
W11256517A
ELECTRIC RANGE
USER INSTRUCTIONS
Table of Contents
RANGE SAFETY .......................................................................... 2
The Anti-Tip Bracket ................................................................. 2
FEATURE GUIDE .........................................................................4
COOKTOP USE ........................................................................... 6
Cookware ..................................................................................7
Home Canning .......................................................................... 8
OVEN USE ...................................................................................9
Electronic Oven Controls .......................................................... 9
Sabbath Mode ..........................................................................9
Keep Warm .............................................................................10
Positioning Racks and Bakeware ...........................................10
Oven Vent ...............................................................................11
Baking and Roasting ..............................................................11
Broiling .................................................................................... 11
Cook Time ..............................................................................11
RANGE CARE ............................................................................12
Self-Cleaning Cycle ................................................................12
General Cleaning ....................................................................13
Oven Light ..............................................................................14
TROUBLESHOOTING ...............................................................15
ASSISTANCE OR SERVICE ...................................................... 16
2
RANGE SAFETY
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Slide range forward.
Look for the anti-tip bracket securely attached to floor or wall.
Slide range back so rear range foot is under anti-tip bracket.
See installation instructions for details.
WARNING
Anti-Tip
Bracket
Range Foot
3
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
WARNING:
TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS
UNDER ANTI-TIP BRACKET.
CAUTION: Do not store items of interest to children in
cabinets above a range or on the backguard of a range
children climbing on the range to reach items could be
seriously injured.
Proper Installation Be sure the range is properly installed
and grounded by a qualified technician.
Never Use the Range for Warming or Heating the Room.
Do Not Leave Children Alone Children should not be left
alone or unattended in area where the range is in use.
They should never be allowed to sit or stand on any part of
the range.
Wear Proper Apparel Loose-fitting or hanging garments
should never be worn while using the range.
User Servicing – Do not repair or replace any part of the
range unless specifically recommended in the manual. All
other servicing should be referred to a qualified technician.
Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
Do Not Use Water on Grease Fires – Smother fire or flame
or use dry chemical or foam-type extinguisher.
Use Only Dry Potholders Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholder touch hot heating elements. Do not use a towel
or other bulky cloth.
DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
UNITS – Surface units may be hot even though they are
dark in color. Areas near surface units may become hot
enough to cause burns. During and after use, do not touch,
or let clothing or other flammable materials contact surface
units or areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and surfaces
facing the cooktop.
Use Proper Pan Size The range is equipped with one or
more surface units of different size. Select utensils having
flat bottoms large enough to cover the surface unit heating
element. The use of undersized utensils will expose a
portion of the heating element to direct contact and may
result in ignition of clothing. Proper relationship of utensil to
burner will also improve efficiency.
Never Leave Surface Units Unattended at High Heat
Settings – Boilover causes smoking and greasy spillovers
that may ignite.
Make Sure Reflector Pans or Drip Bowls Are in Place
Absence of these pans or bowls during cooking may
subject wiring or components underneath to damage.
Protective Liners Do not use aluminum foil to line surface
unit drip bowls or oven bottoms, except as suggested in
the manual. Improper installation of these liners may result
in a risk of electric shock, or fire.
Glazed Cooking Utensils Only certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed
utensils are suitable for range-top service without breaking
due to the sudden change in temperature.
Utensil Handles Should Be Turned Inward and Not Extend
Over Adjacent Surface Units To reduce the risk of burns,
ignition of flammable materials, and spillage due to
unintentional contact with the utensil, the handle of a
utensil should be positioned so that it is turned inward, and
does not extend over adjacent surface units.
Do Not Soak Removable Heating Elements – Heating
elements should never be immersed in water.
Do Not Cook on Broken Cooktop – If cooktop should
break, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock. Contact
a qualified technician immediately.
Clean Cooktop With Caution If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to
avoid steam burn. Some cleaners can produce noxious
fumes if applied to a hot surface.
Use Care When Opening Door Let hot air or steam
escape before removing or replacing food.
Do Not Heat Unopened Food Containers – Build-up of
pressure may cause container to burst and result in injury.
Keep Oven Vent Ducts Unobstructed.
Placement of Oven Racks Always place oven racks in
desired location while oven is
cool. If rack must be moved
while oven is hot, do not let potholder contact hot heating
element in oven.
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
SURFACES OF OVEN – Heating elements may be hot even
though they are dark in color. Interior surfaces of an oven
become hot enough to cause burns. During and after use,
do not touch, or let clothing or other flammable materials
contact heating elements or interior surfaces of oven until
they have had sufficient time to cool. Other surfaces of the
appliance may become hot enough to cause burns – among
these surfaces are oven vent openings and surfaces near
these openings, oven doors, and windows of oven doors.
For self-cleaning ranges
Do Not Clean Door Gasket The door gasket is essential
for a good seal. Care should be taken not to rub, damage,
or move the gasket.
Do Not Use Oven Cleaners No commercial oven cleaner
or oven liner protective coating of any kind should be used
in or around any part of the oven.
Clean Only Parts Listed in Manual.
Before Self-Cleaning the Oven Remove broiler pan and
other utensils.
For units with ventilating hood
Clean Ventilating Hoods Frequently Grease should not
be allowed to accumulate on hood or filter.
When flambeing foods under the hood, turn the fan on.
4
FEATURE GUIDE
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or the Frequently Asked
Questions section of our website at www.whirlpool.com for more detailed instructions.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
KEYPAD FEATURE INSTRUCTIONS
CLOCK Clock
The Clock uses a 12-hour cycle.
1. Check that the oven is OFF.
2. Press CLOCK.
3. Press Temp/Time “up” or “down” arrow keypad to set the hours. Press CLOCK to switch
to the minutes. Press Temp/Time “up” or “down” arrow keypad to set the minutes.
4. Press CLOCK or START.
LIGHT Oven cavity light
While the oven door is closed, press LIGHT to turn the light on and off. The oven light will
come on when the oven door is opened. The oven light will not come on during the Self-
Cleaning cycle.
TIMER SET/OFF Oven timer
The Timer can be set in hours or minutes up to 9 hours and 59 minutes.
1. Press TIMER SET/OFF.
2. Press Temp/Time “up” or “down” arrow keypad to set the length of time.
3. Press START to begin the countdown. If enabled, end-of-cycle tones will sound at end of
countdown.
4. Press TIMER SET/OFF to cancel the Timer. Do not press CANCEL because the oven will
turn off.
START Cooking start
The Start keypad begins any oven function. If Start is not pressed within 10 seconds, a tone
will sound and Start will blink until pressed or canceled. If Start is not pressed within 30
seconds after pressing a keypad, the function is canceled and the time of day is displayed.
CANCEL Range function
The Cancel keypad stops any function except the Timer and Oven Control Lockout.
TEMP/TIME Temperature and
time adjust
The Temp/Time “up” and “down” arrow keypads are used to adjust time and temperature
settings.
BAKE Baking and
roasting
1. Press BAKE.
2. Press Temp/Time “up” or “down” arrow keypad until desired temperature is reached.
A tone will sound if the minimum or maximum temperature is reached.
3. Press START.
4. To change the temperature, repeat Step 2. Press START.
5. Press CANCEL when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed.
All timers, including any active Cook Time or Timed Cook functions, will continue to count
down.
CLEAN
(on some models)
Self-Cleaning
cycle
See the “Self-Cleaning Cycle” section.
5
KEYPAD FEATURE INSTRUCTIONS
FROZEN BAKE Prepackaged
food
1. Position the food on a at rack in the oven on rack position 3. See the “Positioning
Racks and Bakeware” section.
NOTE: Cook only 1 package of frozen food at a time when using Frozen Bake™
Technology.
2. Press FROZEN BAKE LASAGNA or PIZZA.
3. Press the Temp/Time “up” or “down” arrow keypad to set the temperature as
recommended on the food packaging.
4. Press COOK TIME.
5. Press the Temp/Time “up” or “down” arrow keypad to set the maximum cook time as
recommended on the food packaging.
6. Press START. The range will calculate the best cook time based on the current oven
temperature.
NOTE: The cook time that appears in the display is the estimated required cook time as
calculated by the oven control. It may be different than the time you entered. A beep will
alert you to check the food’s doneness with at least 2 minutes remaining on the timer.
To add more time, press the “up” arrow keypad and press START. The time entered is
added to the remaining time
7. Press START to start the calculated time.
8. At the end of the cook time, a beep will alert you to check the food’s doneness. To add
more time, press the “up” arrow keypad and press START. Unless more time is selected,
the bake element turns off.
9. Press CANCEL when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed.
All timers, including any active Cook Time or Timed Cook functions, will continue to count
down.
BROIL Broiling
1. Position cookware in oven and close the oven door.
2. Press BROIL.
3. Press Temp/Time “up” or “down” arrow keypad until the desired temperature is reached.
A tone will sound if the minimum or maximum temperature is reached.
4. Press START.
5. To change the temperature, repeat Step 3. Press START.
6. Press CANCEL when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed.
All timers, including any active Cook Time or Timed Cook functions, will continue to count
down.
KEEP WARM Hold warm
Food must be at serving temperature before placing it in the warmed oven.
1. Press KEEP WARM.
2. Temperature is set at 170°F (75°C). Press the Temp/Time “up” or “down” arrow keypad
until desired temperature is reached. A tone will sound if the minimum or maximum
temperature is reached.
3. Press START.
4. Press CANCEL when nished.
NOTE: The convection fan will shut off when the oven door is opened. If the oven door
remains open for too long, the heating elements will shut off until the oven door is closed.
All timers, including any active Cook Time or Timed Cook functions, will continue to count
down.
DELAY Delayed start
The Delay keypad is used to enter the starting time for an oven function with a delayed start.
Delay should not be used for foods such as breads and cakes because they may not bake
properly.
To set a Timed Cook or a Delayed Timed Cook, see “Cook Time” section.
COOK TIME Timed cooking
Cook Time allows the oven to be set to turn on at a certain time of day, cook for a set length
of time, and/or shut off automatically.
To set a Timed Cook or a Delayed Timed Cook, see “Cook Time” section.
CONTROL LOCK
hold 3 sec
Oven and
cooktop control
lockout
1. Check that the oven and cooktop are OFF.
2. Press and hold CONTROL LOCK for 3 seconds.
3. A tone will sound and a lock will be displayed.
4. Repeat to unlock. No keypad will function with the controls locked.
NOTE: The control lock cannot be activated or deactivated while the Hot Surface
indicator light is on. Wait for the Hot Surface indicator light to turn off before activating or
deactivating the control lock.
6
COOKTOP USE
IMPORTANT: When cooktop is in use, the Self-Cleaning cycle
will be disabled. When the Self-Cleaning cycle is in use, the
cooktop will be locked.
Ceramic Glass (on some models)
The surface cooking area will glow red when an element is ON.
Some parts of the surface cooking area may not glow red when
an element is ON. This is normal operation. It will also randomly
cycle off and back on again, even while on High, to keep the
cooktop from extreme temperatures.
It is normal for the surface of light colored ceramic glass to
appear to change color when surface cooking areas are hot.
As the glass cools, it will return to its original color.
Clean the cooktop after each use to help avoid scratches, pitting,
abrasions and to condition the glass surface. Ceramic glass
cooktop cleaner and a cooktop scraper are also recommended
for stubborn soils. Do not use abrasive cleaners, cleaning pads,
or harsh chemicals for cleaning. Refer to the “Range Care”
section for additional information.
IMPORTANT: To avoid permanent damage to the cooktop surface
and to make soils easier to remove, clean the cooktop after each
use to remove all soils.
Avoid storing jars or cans above the cooktop. Dropping
a heavy or hard object onto the cooktop could crack the
cooktop.
To avoid damage to the cooktop, do not leave a hot lid on
the cooktop. As the cooktop cools, air can become trapped
between the lid and the cooktop and the ceramic glass could
break when the lid is removed.
For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Then, while wearing oven mitts, remove the spills
using a scraper while the surface is still warm. If sugary spills
are allowed to cool down, they can adhere to the cooktop and
can cause pitting and permanent marks.
To avoid scratches, do not slide cookware or bakeware across
the cooktop. Aluminum or copper bottoms and rough nishes
on cookware or bakeware could leave scratches or marks on
the cooktop.
Do not cook popcorn in prepackaged aluminum containers on
the cooktop. They could leave aluminum marks that cannot
be removed completely.
To avoid damage to the cooktop, do not allow objects that
could melt, such as plastic or aluminum foil, to touch any part
of the entire cooktop.
To avoid damage to the cooktop, do not use the cooktop as a
cutting board.
Use cookware about the same size as the surface cooking
area. Cookware should not extend more than 1/2" (1.3 cm)
outside the area.
Use at-bottomed cookware for best heat conduction and
energy efciency. Cookware with rounded, warped, ribbed,
or dented bottoms could cause uneven heating and poor
cooking results.
Determine atness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the
ruler, no space or light should be visible between it and the
cookware.
Cookware designed with slightly indented bottoms or small
expansion channels can be used.
Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
To avoid damage to the cooktop, do not cook foods directly
on the cooktop.
Ceramic Glass Cooktop Cleaning (on some models)
Clean the cooktop after each use to help avoid scratches, pitting,
abrasions and to condition the glass surface. Ceramic glass
cooktop cleaner and a cooktop scraper are also recommended
for stubborn soils. Do not use abrasive cleaners, cleaning pads,
or harsh chemicals for cleaning. Refer to the “Range Care”
section for additional information.
IMPORTANT: To avoid permanent damage to the cooktop surface
and to make soils easier to remove, clean the cooktop after each
use to remove all soils.
WARNING
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
A. Surface cooking area
B. Cookware/canner
C. 1/2" (1.3 cm) maximum overhang
A
B
C
7
Cooktop On Indicator Light
The Cooktop On indicator light is located on the display panel.
When any cooktop element on the console panel is turned on, the
Cooktop On indicator light will glow.
Hot Surface Indicator Light
On ceramic glass models, the Hot Surface indicator light is
located on the display panel.
The Hot Surface indicator light will glow as long as any surface
cooking area is too hot to touch, even after the surface cooking
area is turned off.
The control lock cannot be turned on or off while the Hot Surface
indicator light is on. Wait for the Hot Surface indicator light to turn
off before turning the control lock on or off.
Coil Elements and Burner Bowls (on some models)
Coil elements should be level for optimal cooking results. Burner
bowls, when clean, reect heat back to the cookware. They also
help catch spills.
Cookware should not extend more than 1/2" (1.3 cm) over the
coil element. If cookware is uneven or too large, it can produce
excess heat, causing the burner bowl to change color.
Dual Zone Cooking Element (on some models)
The Dual Zone Cooking Element offers exibility depending on
the size of the cookware. Single size can be used in the same way
as a regular element. The dual size combines both the single and
outer elements and is recommended for larger size cookware.
1. Press ON/OFF for the desired Dual Zone element.
2. Press SIZE to select dual element and a picture of the dual
element will appear.
3. Press the “up” and “down” element arrow keypads to adjust
the heating element to the desired level.
4. To switch back to the single element, press SIZE.
5. Press ON/OFF for the selected element to turn the
element off.
Melt Cooking Element
The Melt cooking element offers exibility due to a wide range of
settings between High and Melt. The High heat option can be
used to boil small amounts of liquid quickly. The lowest setting
can be used to prepare sauces and to keep foods at a low
temperature. Use cookware appropriate in size for the Melt
element.
To reduce the power setting to Melt, press the “down” arrow for
the Melt element until “Melt” appears in the display.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element, or surface burner.
Ideal cookware should have a at bottom, straight sides, and a
well-tting lid, and the material should be of medium-to-heavy
thickness.
Rough nishes may scratch the cooktop. Aluminum and
copper may be used as a core or base in cookware. However,
when used as a base, they can leave permanent marks on the
surfaces.
Cookware material is a factor in how quickly and evenly heat
is transferred which affects cooking results. A nonstick nish
has the same characteristics as its base material. For example,
aluminum cookware with a nonstick nish will take on the
properties of aluminum.
Cookware with nonstick surfaces should not be used under the
broiler.
Check for atness by placing the straight edge of a ruler across
the bottom of the cookware. While you rotate the ruler, no space
or light should be visible between it and the cookware.
A
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2 0
1
2
3
4
5
6
7
A. Dual cooking element
8
Use the following chart as a guide for cookware material
characteristics.
COOKWARE CHARACTERISTICS
Aluminum
Heats quickly and evenly.
Suitable for all types of cooking.
Medium or heavy thickness is best for
most cooking tasks.
May leave aluminum residues
which may be diminished if cleaned
immediately after cooking.
Cast iron
Heats slowly and evenly.
Good for browning and frying.
Maintains heat for slow cooking.
Rough edges or burrs may scratch the
cooktop.
Ceramic or
Ceramic glass
Follow manufacturer’s instructions.
Heats slowly, but unevenly.
Ideal results on low-to-medium heat
settings.
May scratch the cooktop.
Copper
Heats very quickly and evenly.
May leave copper residues which may
be diminished if cleaned immediately
after cooking.
Can leave a permanent stain or bond to
the cooktop if overheated.
Earthenware
Follow manufacturer’s instructions.
Use on low heat settings.
May scratch the cooktop.
Porcelain
enamel-on-
steel or cast
iron
See stainless steel or cast iron.
Porcelain enamel bakeware without the
metal base may bond to the cooktop if
overheated.
Stainless steel
Heats quickly, but unevenly.
A core or base of aluminum or copper
on stainless steel provides even
heating.
Use at-bottomed cookware for best cooking results and energy
efciency. The cookware should be about the same size as the
cooking area outlined on the cooktop. Cookware should not
extend more than 1/2" (1.3 cm) outside the area.
Home Canning
Canning can be performed on a glass smooth-top cooking
surface or traditional coil element cooktop. When canning for long
periods, alternate the use of surface cooking areas or elements
between batches. This allows time for the most recently used
areas to cool.
Center the canner on the largest surface cooking area or
element. On electric cooktops, canners should not extend
more than 1/2" (1.3 cm) beyond the surface cooking area or
element.
Do not place canner on 2 surface cooking areas or elements
at the same time.
On ceramic glass models, use only at-bottomed canners to
avoid damage to the cooktop and elements.
For more information, contact your local agricultural extension
ofce or refer to published home canning guides. Companies
that manufacture home canning products can also offer
assistance.
9
OVEN USE
Odors and smoke are normal when the oven is used the rst few
times or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and
well-ventilated room.
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
Electronic Oven Controls
Control Display
The display will ash when powered up or after a power loss.
Press CANCEL to clear. When oven is not in use, the time of day
is displayed.
Fahrenheit and Celsius
The temperature is preset to Fahrenheit but can be changed
toCelsius.
To change: Press and hold the Temp/Time “up” arrow keypad
for 5 seconds. “°C” or “°F” will appear on the display. Repeat to
change back.
To exit mode, press CANCEL.
Keypress Tones
Activates or turns off the tones when a keypad is pressed.
To change: Press and hold LIGHT for 5 seconds. Repeat to
change back.
To exit mode, press CANCEL.
Demo Mode
IMPORTANT: This feature is intended for use on the sales oor
with 120 V power connection and permits the control features
to be demonstrated without heating elements turning on. If this
feature is activated, the oven will not work.
To change: Press CANCEL, CANCEL, Temp/Time “up” arrow
keypad, TIMER SET/OFF. Repeat to change back and end
Demomode.
Tones
Tones are audible signals, indicating the following:
Basic Functions
One Tone
Valid keypad press
Oven is preheated (long tone)
Function has been entered
Reminder, repeating every 20 seconds after the
end-of-cycle tones
Three Tones
Invalid keypad press
Four Tones
End of cycle
Oven Temperature Control
IMPORTANT: Do not use a thermometer to measure oven
temperature. Elements will cycle on and off as needed to provide
consistent temperature but may run slightly hot or cool at any
point in time due to this cycling. Most thermometers are slow
to react to temperature change and will not provide an accurate
reading due to this cycling.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature can
be adjusted to personalize it for your cooking needs. It can be
changed in Fahrenheit or Celsius.
To Adjust Oven Temperature:
1. Press and hold the Temp/Time “down” arrow keypad for
5seconds until the oven display shows the current setting, for
example “0°F CAL” or “00.”
2. Press the Temp/Time “up” or “down” arrow keypad to
increase or to decrease the temperature in 5°F (3°C) amounts.
The adjustment can be set between 30°F (18°C) and -30°F
(-18°C).
3. Press START.
Sabbath Mode
(on some models)
The Sabbath mode sets the oven to remain on in a Bake setting
until turned off. A Timed Bake can also be set to keep the oven
on for only part of the Sabbath. The Oven Control Lockout feature
(if present) will be disabled during the Sabbath mode. After the
Sabbath mode is set, no tones will sound, the display will not
show the temperature, the Kitchen Timer mode will be canceled
(if active), and only the following keypads will function:
Temp/Time “up” and “down” arrow keypads
Cancel
When the oven door is opened or closed, the oven light will not
turn on or off and the heating elements will not turn on or off
immediately.
When power is restored after a power failure, the oven will return
to Sabbath mode and remain Sabbath compliant with the bake
elements off until the Cancel keypad is pressed.
Pressing the Cancel keypad at any time cancels the cooking cycle
and returns the oven to the normal cooking mode (not Sabbath
compliant).
Before entering the Sabbath mode, it must be decided if the oven
light is to be ON or OFF for the entire Sabbath mode period. If
the light is ON when entering Sabbath mode, it will remain ON for
the entire time Sabbath mode is in use. If the light is OFF when
entering Sabbath mode, it will remain OFF for the entire time
Sabbath mode is in use. Opening the oven door or pressing the
Light keypad will not affect the oven light once Sabbath mode
has been entered.
On the Holiday, the oven temperature can be changed once the
oven is in Sabbath mode by pressing the Temp/Time “up” or
“down” arrow keypad. The oven temperature will change 25°F
(14°C) each time the Temp/Time “up” and “down” arrow keypads
are pressed. Press START to activate the new temperature. The
display will not change and there will be no sounds during this
adjustment.
To Bake Using Sabbath Mode:
1. Press BAKE.
2. To change the temperature, press the Temp/Time “up” or
“down” arrow keypad.
3. Press START.
4. Press and hold the Timer Set/Off keypad for 5 seconds.
“SAb” will ash in the display.
5. Press START while “SAb” is ashing to enter Sabbath mode;
otherwise, the entire cycle cancels out. “SAb” will stop
ashing and remain on in the display. The oven is now in
Sabbath mode and is Sabbath compliant.
10
Pressing the Cancel keypad at any time cancels the cooking cycle
and returns the oven to the normal cooking mode (not Sabbath
compliant).
To Set a Timed Bake Using Sabbath Mode
(on some models):
1. Press BAKE.
2. Press the Temp/Time “up” or “down” arrow keypad to enter a
temperature other than the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light will
light up.
4. Press the Temp/Time “up” or “down” arrow keypad to enter a
cook time length.
5. Press START.
6. Press and hold the Timer Set/Off keypad for 5 seconds.
“SAb” will ash in the display.
7. Press START while “SAb” is ashing to enter Sabbath mode;
otherwise, the entire cycle cancels out. “SAb” will stop
ashing and remain on in the display. The oven is now in
Sabbath mode and is Sabbath compliant. The Bake, On, and
Cook Time indicator lights will be displayed.
When the set cook time ends, the oven will shut off automatically
and the indicator lights will turn off, indicating the end of the
cycle.
Pressing the Cancel keypad at any time cancels the cooking cycle
and returns the oven to the normal cooking mode (not Sabbath
mode compliant).
To Set a Delayed Timed Bake Using Sabbath Mode
(on some models):
1. Press BAKE.
2. Press the Temp/Time “up” or “down” arrow keypad to enter a
temperature other than the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light will
light up.
4. Press the Temp/Time “up” or “down” arrow keypad to enter a
cook time length.
5. Press DELAY. The Delay indicator light will light up.
6. Press the Temp/Time “up” or “down” arrow keypad to enter a
start time.
7. Press START.
8. Press and hold the Timer Set/Off keypad for 5 seconds.
“SAb” will ash in the display.
9. Press START while “SAb” is ashing to enter Sabbath mode;
otherwise, the entire cycle cancels out. “SAb” will stop
ashing and remain on in the display. The oven is now in
Sabbath mode and is Sabbath compliant. The Delay indicator
light will be displayed.
When the start time is reached the Bake, On, and Cook Time
indicator lights will automatically turn on. When the set cook time
ends, the oven will shut off automatically and the indicator lights
will turn off, indicating the end of the cycle.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath mode compliant).
Keep Warm
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
IMPORTANT: Food must be at serving temperature before
placing it in the warmed oven. Food may be held up to 1 hour;
however, breads and casseroles may become too dry if left in the
oven during the Keep Warm function. For best results, coverfood.
The Keep Warm feature allows hot cooked foods to stay at
serving temperature.
To Use:
1. Press WARM.
2. Press Temp/Time “up” or “down” arrow keypad until desired
temperature is reached. A tone will sound if the minimum or
maximum temperature is reached.
3. Press START.
4. Place food in the oven.
5. Press CANCEL when nished.
NOTE: The temperature may be changed at any time by pressing
the Temp/Time “up” or “down” arrow keypad to thedesired
temperature and then START.
Aluminum Foil
IMPORTANT: To avoid permanent damage to the oven bottom
nish, do not line the oven bottom with any type of foil or liner.
For best cooking results, do not cover entire oven rack with foil
because air must be able to move freely.
Positioning Racks and Bakeware
IMPORTANT: To avoid permanent damage to the porcelain
nish, do not place food or bakeware directly on the oven door
orbottom.
Bakeware
To cook food evenly, hot air must be able to circulate. Allow
2" (5cm) of space around bakeware and oven walls. Make sure
thatno bakeware piece is directly over another.
Racks
Position racks before turning on the oven.
Do not position racks with bakeware on them.
Make sure racks are level.
To move a rack, pull it out to the stop position, raise the front
edge, and then lift out. Use the following illustration as a guide.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
1
2
3
4
5
11
Rack Positions
Rack 5: Toasting bread or broiling thin, non-fatty foods
Rack 4: 2-rack baking and broiling
Rack 3: Most baked goods on a cookie sheet, mufn pan, or jelly
roll pan; layer cakes; broiling chicken pieces
Rack 2: Pies, casseroles, yeast bread, quick breads, frozen
convenience foods, 2-rack baking
Rack 1: Roasting large and small cuts of meat and poultry
Multiple Rack Cooking
2-rack: Use rack positions 2 and 4.
Baking Layer Cakes on 2 Racks
For best results when baking cakes on 2 racks, use racks 2 and 4
for baking. Place the cakes on the racks as shown.
Oven Vent
The oven vent releases hot air and moisture from the oven
andshould not be blocked or covered. Blocking or covering the
oven vent will cause poor air circulation, affecting cooking and
cleaning results. Do not set plastics, paper, or other items that
could melt or burn near the oven vent.
On coil element models, the element can be used when the oven
is in use as long as the cookware does not extend more than
1/2"(1.3 cm) over the element.
Baking and Roasting
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
ACCUBAKE
®
Temperature Management System
The ACCUBAKE
®
system electronically regulates the oven heat
levels during preheat and Bake to maintain a precise temperature
range for optimal cooking results. The bake and broil elements
or burners cycle on and off in intervals. On convection range
models, the fan will run while preheating and may be cycled on
and off for short intervals during Bake to provide the best results.
This feature is automatically activated when the oven is in use.
Before baking and roasting, position racks according to
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven preheat cycle to end before
putting food in unless it is recommended in the recipe.
Preheating
When Start is pressed, the oven will begin preheating. Once
100ºF (38ºC) is reached, the display temperature will increase as
the actual temperature of the oven increases. When the preheat
temperature is reached, a tone will sound and the selected
temperature will appear on the display.
Broiling
NOTE: The convection fan will shut off when the oven door is
opened. If the oven door remains open for too long, the heating
elements will shut off until the oven door is closed. All timers,
including any active Cook Time or Timed Cook functions, will
continue to count down.
IMPORTANT: Close the door to ensure proper broiling
temperature.
Changing the temperature when Custom Broiling allows more
precise control when cooking. The lower the broil setting is, the
slower the cooking. Thicker cuts and unevenly shaped pieces of
meat, sh, and poultry may cook better at lower broil settings.
Use rack 4 or 5 for broiling. Refer to the “Positioning Racks and
Bakeware” section for more information.
On lower settings, the broil element will cycle on and off to
maintain the proper temperature.
For best results, use a broiler pan and grid. It is designed to
drain juices and help avoid spatter and smoke.
NOTE: Odors and smoke are normal the rst few times the oven
is used or if the oven is heavily soiled.
Cook Time
To Set a Timed Cook:
1. Press BAKE. The Bake indicator light will light up.
2. Press the Temp/Time “up” or “down” arrow keypad to enter a
temperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will
light up.
4. Press the Temp/Time “up” or “down” arrow keypad to enter
the length of time to cook.
5. Press START. The display will count down the time. When the
time ends, the oven will shut off automatically.
6. Press CANCEL to clear the display.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time
of day. See the “Clock” keypad feature in the “Feature Guide”
section.
1. Press BAKE.
2. Press the Temp/Time “up” or “down” arrow keypad to enter a
temperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will
light up.
4. Press Temp/Time “up” or “down” arrow keypad to enter the
length of time to cook.
5. Press DELAY. The delay oven indicator light will light up.
6. Press Temp/Time “up” or “down” arrow keypad to enter the
time of day to start.
7. Press START.
When the start time is reached, the oven will automatically turn
on. The Temperature and/or Cook Time settings can be changed
anytime after the oven turns ON by repeating steps 2-4 and
pressing Start. To change to a different delay time, cancel the
feature and repeat steps 1-7. When the set cook time ends, the
oven will shut off automatically.
8. Press CANCEL to clear the display.
A
A. Oven vent
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
12
RANGE CARE
Self-Cleaning Cycle
(on some models)
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to
the fumes may result in death to certain birds. Always move birds
to another closed and well-ventilated room.
Do not block the oven vent during the Self-Cleaning cycle. Air
must be able to move freely. Depending on your model, see
“Oven Vent” section.
Do not clean, rub, damage, or move the oven door gasket.
Prepare Range
Remove the broiler pan, grid, cookware and bakeware, all
cooking utensils, oven racks and aluminum foil and, on some
models, the temperature probe from the oven.
Use a damp cloth to clean inside door edge and the
1
1
/
2
"(3.8cm) area around the inside oven cavity frame,
beingcertain not to move or bend the gasket.
Remove plastic items from the cooktop because they
maymelt.
Remove all items from the storage drawer.
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks, and
popping sounds.
Before Self-Cleaning, make sure the door is completely closed or
the door will not lock and the Self-Cleaning cycle will not begin.
Once the oven has completely cooled, remove ash with a damp
cloth. To avoid breaking the glass, do not apply a cool damp cloth
to the inner door glass before it has completely cooled.
To stop the Self-Cleaning cycle at any time, press CANCEL.
Ifthe temperature is too high, the oven door will remain locked
and “cool” and “locked” will be displayed. The cooling fan may
continue to run.
The oven light will not function during the Self-Cleaning cycle.
Electronic Oven Control with Adjustable Clean Time
(on some models)
The Self-Cleaning cycle is time adjustable between 2 hours
30minutes and 4 hours 30 minutes in 30-minute increments.
Suggested clean times are 2 hours 30 minutes for light soil, and 4
hours 30 minutes for heavy soil.
IMPORTANT: When cooktop is in use, the Self-Cleaning cycle will
be disabled. When the Self-Cleaning cycle is in use, the cooktop
will be locked.
To Self-Clean:
1. Press CLEAN.
2. Press the Temp/Time “up” or “down” arrow keypad to enter
the desired Self-Cleaning cycle time.
3. Press START.
The oven door will automatically lock. The Door Locked and
Clean indicator lights will be displayed. The time remaining
will also be displayed.
4. When the Self-Cleaning cycle is complete and the oven cools,
the Door Locked and Clean indicator lights will turnoff.
5. When the oven is completely cooled, remove ash with a damp
cloth.
To exit the Self-Cleaning cycle before completed, press
CANCEL. The door will unlock once the oven cools.
WARNING
Burn Hazard
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during
Self-Cleaning cycle.
Failure to follow these instructions can result in burns.
13
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are OFF and
the oven and cooktop are cool. Always follow label instructions
on cleaning products. For additional information, you can visit
the Frequently Asked Questions (FAQs) section ofour website at
www.whirlpool.com.
Soap, water, and a soft cloth or sponge are suggested rst
unlessotherwise noted.
EXTERIOR PORCELAIN ENAMEL SURFACES
(on some models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire range is cool. These spills may
affect the nish.
Cleaning Method:
Glass cleaner, mild liquid cleaner, or nonabrasive
scrubbingpad:
Gently clean around the model/serial/rating plate
becausescrubbing may remove numbers.
STAINLESS STEEL (on some models)
NOTE: To avoid damage to stainless steel surfaces, do not use
soap-lled scouring pads, abrasive cleaners, Cooktop Cleaner,
steel-wool pads, gritty washcloths, or abrasive paper towels.
Damage may occur to stainless steel surfaces, even with one-
time or limited use.
Cleaning Method:
Rub in direction of grain to avoid damaging.
METALLIC PAINT (on some models)
Do not use abrasive cleaners, cleaners with bleach, rust
removers, ammonia, or sodium hydroxide (lye) because
paintsurface may stain.
CERAMIC GLASS (on some models)
Cleaning Method:
To avoid damaging the cooktop, do not use steel wool, abrasive
powder cleansers, chlorine bleach, rust remover, or ammonia.
1. Remove food/residue with the Cooktop Scraper.
For best results, use the Cooktop Scraper while the
cooktop is still warm but not hot to the touch. It is
recommended to wear an oven mitt while scraping
thewarm cooktop.
Hold the Cooktop Scraper at approximately a 45° angle
against the glass surface and scrape the residue. It will
be necessary to apply pressure in order to remove the
residue.
Allow the cooktop to cool down completely before proceeding
to Step 2.
2. Apply a few dime-sized drops of Cooktop Cleaner tothe
affected areas.
Rub Cooktop Cleaner onto the cooktop surface with the
blue Cooktop Cleaning Pad. Some pressure is needed to
remove stubborn stains.
Allow the cleaner to dry to a white haze before proceeding
to Step 3.
3. Polish with a clean, dry cloth or a clean, dry paper towel.
Repeat steps 1 through 3 as necessary for stubborn
orburned-on stains.
COOKTOP CONTROLS
To avoid damage to the cooktop controls, do not use steel wool,
abrasive cleansers, or oven cleaner.
To avoid damage, do not soak knobs.
When replacing knobs, make sure knobs are in the OFF position.
On some models, do not remove seals under knobs.
Cleaning Method:
Soap and water:
Pull knobs straight away from control panel to remove.
CONTROL PANEL AND OVEN DOOR EXTERIOR
To avoid damage to the control panel, do not use abrasive
cleaners, steel-wool pads, gritty washcloths, or abrasive
papertowels.
Cleaning Method:
Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly
onpanel.
14
COIL ELEMENTS (on some models)
Cleaning Method:
Damp cloth:
Make sure control knobs are OFF and elements are cool.
Do not clean or immerse in water. Soil will burn off when hot.
BURNER BOWLS (on some models)
Before removing or replacing coil elements and burner bowls,
make sure they are cool and the control knobs are in the Off
position.
Remove the coil element by pushing the edge of the coil element
toward the receptacle. Lift it enough to clear the burner bowl. Pull
the coil element straight away from the receptacle to remove. Lift
out the burner bowl.
Cleaning Method:
Chrome burner bowls
Wash frequently in warm, soapy water. (It is not recommended to
wash chrome bowls in a dishwasher.) A mild abrasive cleaner and
a plastic scrubber can be used to remove stubborn stains.
For heavily soiled bowls, place an ammonia-soaked paper towel
on the stains and allow to soak for a short time, then gently scrub
with a plastic scrubber.
SURFACE UNDER COOKTOP (on some models)
The coil cooktop will lift up to provide easy access for cleaning
beneath. Lift the cooktop by both front corners until the support
locks into place.
Cleaning Method:
Glass cleaner, mild liquid cleaner, or nonabrasive scrubbing pad.
To avoid damage to the range, do not remove the cooktop.
OVEN RACKS
Cleaning Method:
Steel-wool pad
For racks that have discolored and are harder to slide,
alightcoating of vegetable oil applied to the rack guides
willhelp them slide.
STORAGE DRAWER (on some models)
Check that storage drawer is cool and empty before cleaning.
Cleaning Method:
Mild detergent
OVEN CAVITY
Do not use oven cleaners on models with Self-Cleaning.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining,
etching,pitting, or faint white spots can result.
Cleaning Method:
See the “Self-Cleaning Cycle” section.
Oven Light
The oven light is a standard 40 W appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the Off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
15
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Operation
PROBLEM POSSIBLE CAUSES SOLUTIONS
Nothing will operate
Power supply cord is unplugged. Plug into a grounded outlet.
Household fuse is blown or a
circuit breaker is tripped.
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
The control displays an F9 or F9
E0 error code.
The electrical outlet in the home may be miswired. Contact a
qualied electrician to verify the electrical supply.
Cooktop will not operate
The control knob is set incorrectly. Push in knob before turning to a setting.
On ceramic glass models, the
oven Control Lockout is set.
See the “Control Lock” keypad feature in the “Feature Guide.”
Excessive heat around
cookware on cooktop
Cookware that is not the proper
size.
Use cookware about the same size as the surface cooking area,
element, or surface burner. Cookware should not extend more
than 1/2" (1.3 cm) outside the cooking area.
Cooktop cooking results not
what expected
Control knob set to incorrect
heat level.
See the “Cooktop Use” section.
Range is not level. Level the range. See the Installation Instructions.
Cooktop element cycles on
and off on High setting
Element cycling due to a
temperature limiter.
This is normal operation. The element may cycle on and off to
keep the cooktop from overheating.
Oven will not operate
Delay Start is set. See the “Electronic Oven Controls” section.
Control lock is ON. Press and hold CONTROL LOCK for 3 seconds to unlock.
Control is in Demo mode. Demo mode will deactivate all oven elements. See “Demo
Mode” in the Electronic Oven Controls” section.
Electronic oven control set
incorrectly.
See “Electronic Oven Controls” section.
Cannot turn control lock on/
off
Hot Surface indicator light is ON. Wait for the cooktop surface to cool and try again when the Hot
Surface indicator light turns off.
Oven temperature too high or
too low
Oven temperature needs
adjustment.
See the “Oven Temperature Control” in the “Electronic Oven
Controls” section.
Oven indicator lights flash
Power to range is turned on or
restored.
See “Control Display” in the “Electronic Oven Controls” section.
If the indicator light(s) keep ashing, call for service. See the
“Warranty” for more information.
Display shows messages
Power failure. (Display shows
ashing time.)
Clear the display. On some models, reset the clock, if needed.
See “Clock” keypad feature in the “Feature Guide” section.
Error code. (Display shows letter
followed by number.)
Depending on your model, press CANCEL to clear the display.
See “Control Display” in the “Electronic Oven Controls” section.
If it reappears, call for service. See the “Warranty” for more
information.
Start needs to be pressed so a
cycle can begin.
See the “Start” keypad feature in the “Feature Guide” section.
Self-Cleaning cycle will not
operate
The oven door is not closed. Make sure the oven door is fully closed.
The Self-Cleaning function has
not been entered correctly.
See the “Self-Cleaning Cycle” section.
A Timed Cooking function has
been entered.
See the “Cook Time” section.
The range is in Sabbath mode. See the “Sabbath Mode” section.
16
PROBLEM POSSIBLE CAUSES SOLUTIONS
Oven cooking results not
what expected
Range is not level. Level the range. See the Installation Instructions.
The temperature set was
incorrect.
Double-check the recipe in a reliable cookbook.
Oven temperature is calibrated
incorrectly.
See “Oven Temperature Control” in the “Electronic Oven
Controls” section.
Oven was not preheated. See the “Baking and Roasting” section.
Racks were positioned improperly. See the “Positioning Racks and Bakeware” section.
Not enough air circulation around
bakeware.
See the “Positioning Racks and Bakeware” section.
Batter distributed unevenly in pan. Check that batter is level in the pan.
Darker browning of food caused
by dull or dark bakeware.
Lower oven temperature 25°F (15°C) or move rack to a higher
position in the oven.
Lighter browning of food
caused by shiny or light colored
bakeware.
Move rack to a lower position in the oven.
Incorrect length of cooking time
was used.
Adjust cooking time.
Oven door was not closed. Be sure that the bakeware does not keep the door from closing.
Oven door was opened during
cooking.
Oven peeking releases oven heat and can result in longer
cooking times.
Oven door was open for too long. If the oven door remains open for too long, the heating elements
will shut off until the oven door is closed.
Rack is too close to bake burner,
making baked items too brown on
bottom.
Move rack to higher position in the oven.
Pie crusts browning too quickly. Use aluminum foil to cover the edge of the crust and/or reduce
baking temperature.
Temperature scale was changed
from Fahrenheit to Celsius.
Foods are overdone or burnt even at low temperatures. See
“Fahrenheit and Celsius” in the “Electronic Oven Controls”
section.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you still need help,
check the contact information on the Certificate of Warranty that accompanies the product.
When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us
to better respond to your request.
Nous vous REMERCIONS d’avoir acheté ce produit de grande qualité.
Pour référence ultérieure, consigner par écrit les numéros de modèle et de série de votre produit. Ces numéros gurent sur
l’étiquette située dans le coin supérieur droit du cadre avant.
Numéro de modèle ___________________________________ Numéro de série ______________________________________
INSTRUCTIONS
D’UTILISATION DE LA
CUISINIÈRE ÉLECTRIQUE
Table des matières
SÉCURITÉ DE LA CUISINIÈRE ................................................18
La bride antibasculement .......................................................18
GUIDE DES CARACTÉRISTIQUES ..........................................21
UTILISATION DE LA TABLE DE CUISSON ..............................24
Ustensiles de cuisson ............................................................. 25
Préparation de conserves à la maison ...................................26
UTILISATION AU FOUR ............................................................ 27
Commandes électroniques du four ........................................27
Mode Sabbat ..........................................................................28
Maintien au chaud ..................................................................29
Positionnement des grilles et des
ustensiles de cuisson au four .................................................29
Évent du four ..........................................................................29
Cuisson et rôtissage au four .................................................. 30
Cuisson au gril ........................................................................30
Cook Time (durée de cuisson) ................................................30
ENTRETIEN DE LA CUISINIÈRE .............................................. 31
Programme d’autonettoyage ..................................................31
Nettoyage général...................................................................32
Lampe du four ........................................................................33
DÉPANNAGE .............................................................................34
ASSISTANCE OU SERVICE ...................................................... 36
18
SÉCURITÉ DE LA CUISINIÈRE
La bride antibasculement
La cuisinière ne basculera pas pendant une utilisation normale. Cependant, la cuisinière peut basculer si trop de force ou de poids est
appliqué à la porte de la cuisinière sans que la bride antibasculement n’ait été adéquatement xée.
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
Risque de basculement
Un enfant ou une personne adulte peut faire basculer la cuisinière, ce qui peut causer un
décès.
Vérifier que la bride antibasculement est bien installée et engagée, conformément aux
instructions d'installation.
Réengager la bride antibasculement si la cuisinière a été déplacée.
Ne pas faire fonctionner la cuisinière si la bride antibasculement n'est pas installée et engagée.
Le non-respect de ces instructions peut causer un décès ou des brûlures graves aux enfants et
aux adultes.
Pour vérifier que la bride antibasculement est bien installée et engagée :
Faire glisser la cuisinière vers l'avant.
Vérifier que la bride antibasculement est bien fixée au plancher ou au mur.
Faire de nouveau glisser la cuisinière vers l'arrière de sorte que le pied de la cuisinière
se trouve sous la bride antibasculement.
Voir les instructions d'installation pour plus de détails.
AVERTISSEMENT
Bride
antibasculement
Pied de la cuisinière
19
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
CONSERVEZ CES INSTRUCTIONS
AVERTISSEMENT : Pour réduire le risque d’incendie, de
choc électrique, de blessures ou de dommages lors de
l’utilisation de la cuisinière, il convient d’observer certaines
précautions élémentaires dont les suivantes :
AVERTISSEMENT :
POUR MINIMISER LE RISQUE
DE BASCULEMENT DE LA CUISINIÈRE, ELLE DOIT
ÊTRE BIEN IMMOBILISÉE PAR DES DISPOSITIFS
ANTIBASCULEMENT CORRECTEMENT INSTALLÉS.
POUR VÉRIFIER SI LES DISPOSITIFS SONT
CORRECTEMENT INSTALLÉS, GLISSER LA CUISINIÈRE
VERS L’AVANT ET VÉRIFIER SI LA BRIDE
ANTIBASCULEMENT EST BIEN FIXÉE AU PLANCHER
OU AU MUR, ET GLISSER LA CUISINIÈRE VERS
L’ARRIÈRE POUR QUE LE PIED ARRIÈRE DE LA
CUISINIÈRE SOIT SOUS LA BRIDE
ANTIBASCULEMENT.
MISE EN GARDE : Ne pas remiser dans des armoires
au-dessus de la cuisinière ou sur le dosseret d’une
cuisinière, des objets que des enfants pourraient vouloir
atteindre. Les enfants pourraient se brûler ou se blesser en
grimpant sur la cuisinière.
Installation appropriée – S’assurer que la cuisinière est
correctement installée et reliée à la terre par un technicien
qualifié.
Ne jamais utiliser la cuisinière pour réchauffer ou chauffer
la pièce.
Ne pas laisser les enfants seuls Les enfants ne doivent
pas être laissés seuls ou sans surveillance dans la pièce
la cuisinière est en service. Ne jamais laisser les
enfants s’asseoir ou se tenir sur une partie quelconque de
la cuisinière.
Porter des vêtements appropriés Des vêtements amples
ou détachés ne doivent jamais être portés pendant
l’utilisation de la cuisinière.
Entretien par l’utilisateur Ne pas réparer ni remplacer
toute pièce de la cuisinière si ce n’est pas spécifiquement
recommandé dans le manuel. Toute autre opération
d’entretien ou de réparation doit être confiée à un
technicien qualifié.
Remisage dans ou sur la cuisinière – Des matériaux
inflammables ne doivent pas être remisés dans un four ou
près des éléments de surface.
Ne pas utiliser d’eau pour éteindre un feu de graisse
Étouffer le feu ou les flammes ou utiliser un extincteur à
produits chimiques secs, ou un extincteur à mousse.
N’utiliser que des mitaines sèches de four – Des mitaines
de four mouillées ou humides sur des surfaces chaudes
peuvent provoquer des brûlures provenant de la vapeur.
Ne pas laisser les mitaines de four toucher les éléments
chauffants. Ne pas utiliser une serviette ou un tissu épais.
NE PAS TOUCHER LES ÉLÉMENTS DE SURFACE OU
L’ESPACE PRÈS DES ÉLÉMENTS Les éléments de
surface peuvent être chauds même lorsqu’ils ont une teinte
foncée. Les endroits près des éléments de surface peuvent
devenir assez chauds pour causer des brûlures. Pendant
et après l’utilisation, ne pas toucher les éléments
chauffants et ne pas laisser les vêtements ou autres
matériaux inflammables entrer en contact avec ces
éléments de surface ou les endroits près des éléments,
avant qu’ils soient suffisamment refroidis. Ces endroits
comprennent la table de cuisson et les surfaces près de la
table de cuisson.
Utiliser des ustensiles de dimension appropriée – La
cuisinière est munie d’un ou de plusieurs
éléments
chauffants de différentes grandeurs. Choisir les ustensiles
qui ont un fond plat assez grand pour couvrir l’élément
chauffant de la surface de cuisson. L’utilisation d’ustensiles
trop petits exposera une partie de l’élément chauffant, ce
qui peut provoquer l’inflammation des vêtements.
L’utilisation d’un récipient de dimension correcte améliore
aussi l’efficacité de la cuisson.
Ne jamais laisser les éléments de la table de cuisson sans
surveillance alors qu’ils chauffent à la puissance maximale.
Il pourrait en résulter une ébullition qui cause de la fumée
et des renversements de corps gras qui peuvent
s’enflammer.
S’assurer que les cuvettes réfléchissantes ou les bols de
renversement sont en place L’absence de ces cuvettes
ou bols au cours de la cuisson peut causer des dommages
aux fils ou aux composants en dessous des éléments.
Garnissages protecteurs Ne pas recouvrir les cuvettes
ou le fond du four de papier d’aluminium sauf tel que
suggéré dans le manuel. L’installation incorrecte de papier
d’aluminium ou d’autre matériau peut causer un risque de
choc électrique ou d’incendie.
Ustensiles de cuisson vitrifiés Seulement certains types
d’ustensiles de verre, vitrocéramique, céramique, faïence
ou autres surfaces vitrifiées conviennent pour le service
sur une table de cuisson, sans bris attribuables aux
changements soudains de température.
Les poignées des ustensiles doivent être tournées vers
l’intérieur et non vers le dessus des éléments adjacents
Pour réduire le risque de brûlures, d’inflammation de
produits inflammables et de renversements dus à
l’entrechoquement non intentionnel des ustensiles, la
poignée d’un ustensile doit être positionnée de sorte
qu’elle est tournée vers l’intérieur et non au-dessus des
éléments de surface adjacents.
Ne pas tremper les éléments de chauffage amovibles
Les éléments de chauffage ne doivent jamais être
immergés dans l’eau.
Ne pas faire cuire sur une table de cuisson endommagée
Si la table de cuisson est brisée, les solutions de nettoyage
et les renversements peuvent pénétrer dans la table de
cuisson brisée et créer un risque de choc électrique.
Contacter immédiatement un technicien qualifié.
20
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
CONSERVEZ CES INSTRUCTIONS
Nettoyer la table de cuisson avec prudence – Si une
éponge ou un chiffon mouillé est utilisé pour essuyer les
renversements sur une surface de cuisson chaude, éviter
les brûlures causées par la vapeur chaude. Certains
nettoyants peuvent produire des émanations désagréables
lorsqu’ils sont utilisés sur une surface chaude.
Exercer une grande prudence lors de l’ouverture de la
porte – Laisser l’air chaud ou la vapeur s’échapper avant
d’enlever ou de replacer un plat.
Ne pas faire chauffer des contenants fermés
L’accumulation de pression peut causer une explosion du
contenant et des blessures.
Ne jamais obstruer les ouvertures des évents.
Positionnement des grilles du four Toujours placer les
grilles du four en position désirée pendant que le four est
froid. Si la grille doit être déplacée pendant que le four est
chaud, ne pas laisser les mitaines de four toucher l’élément
chaud du four.
NE PAS TOUCHER LES ÉLÉMENTS CHAUFFANTS OU
LES SURFACES INTÉRIEURES DU FOUR Les
éléments chauffants peuvent être chauds même s’ils ont
une teinte foncée. Les surfaces intérieures d’un four
deviennent assez chaudes pour causer des brûlures.
Pendant et après l’utilisation, ne pas toucher ou laisser des
vêtements ou autres matériaux inflammables venir en
contact avec les éléments chauds ou les surfaces
intérieures chaudes du four avant qu’ils aient eu assez de
temps pour refroidir. D’autres surfaces de l’appareil
peuvent devenir assez chaudes pour causer des brûlures.
Ces surfaces comprennent les ouvertures de l’évent du
four et les surfaces près de ces ouvertures, les portes du
four, et les hublots des portes du four.
Pour les cuisinières avec programme d’autonettoyage
Ne pas nettoyer le joint de la porte Le joint de la porte
est essentiel pour l’étanchéité. Veiller à ne pas frotter,
endommager ou déplacer le joint.
Ne pas utiliser des produits commerciaux de nettoyage du
four – On ne doit pas utiliser un produit commercial de
nettoyage de four ou un enduit de protection des surfaces
internes du four quel qu’en soit le type, sur les surfaces du
four ou les surfaces voisines.
Nettoyer uniquement les pièces indiquées dans le manuel.
Avant d’exécuter le programme d’autonettoyage du four
Ôter la lèchefrite et son plat et les autres ustensiles.
Pour les
appareils avec hotte de ventilation
Nettoyer les hottes de ventilation fréquemment – La
graisse ne doit pas s’accumuler sur la hotte ou le filtre.
Lorsque vous flambez des aliments sous la hotte, mettre le
ventilateur en marche.
1 / 1

Whirlpool WEE510SAGB Mode d'emploi

Catégorie
Cuisinières
Taper
Mode d'emploi