Genie 3024 Manuel utilisateur

Marque: Genie

Modèle: 3024

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

Includes INTELLICODE

2 Remote Control. Safe-T-Beam

System must be installed to close door.

For use only with residential sectional or one piece overhead garage doors.

Homelink

and Car2U

compatible.

For Answers and Assistance:

1.800.354.3643

or visit www.geniepro.com

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

IntelliG

™

1000

Model 3024

GARAGE DOOR OPENER

Homelink

is a registered trademark of Johnson Controls Technology Company. Car2U

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

CONVENTIONS USED IN THESE INSTRUCTIONS

Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving

objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading

the information in this manual. If you have questions or do not understand the information presented, call your nearest trained

door system technician or visit our website.

The following Safety Alert symbol and signal words are used throughout this manual to call attention to and identify different

levels of hazard and special instructions.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and the word "DANGER", "WARNING", or "CAUTION"

DANGER indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

Potential Hazard Effect Prevention

WARNING

Could result in

Death or Serious

Injury

Keep people clear of opening while Door is moving.

Do NOT allow children to play with the Door Opener.

Do NOT operate a Door that jams or one that has a broken

spring.

WARNING

Could result in

Death or Serious

Injury

Turn OFF power before removing opener cover.

When replacing cover, make sure wires are NOT pinched or

near moving parts.

Opener must be fully grounded.

WARNING

Could result in

Death or Serious

Injury

Do NOT try to remove, install, repair or adjust springs or any-

thing to which door spring parts are fastened, such as, wood

blocks, steel brackets, cables or other like items.

Installations, repairs and adjustments must be done by a

trained door system technician using proper tools and instruc-

tions.

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

INTELLICODE

2 Access Security System

A new generation superior encryption system that enhances the security of the door opener by continuously

changing the access code each time the remote is used. The door opener responds to each new code only once.

An access code copied from a working system and tried again will not control the door opener.

OPENER FEATURES

Wall Console

Operates door opener from inside garage. Indicator Light with: Open/Close, Vacation Lock, and Independent

Light Control buttons.

and Car2U

compatible. Refer to the programming instructions on page 9 and then

follow the HomeLink

or Car2U

instructions in your car owner’s manual.

SAFETY FEATURES

Safe-T-Beam

(STB) Non-Contact Reversing System

Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything

passes through the beam. LED indicator lights on the power head and on the STBs provide a self diagnostic code

if an operational problem exists.

Safe-T-Reverse® Contact Reversing System

Automatically stops and reverses a closing door within two seconds of contact with an object.

Automatic ForceGuard

™

Control

Automatically sets the minimum force required to fully open and close the door for maximum safety.

Watch Dog

™

Monitoring System

Monitors the Safe-T-Beam® system to ensure proper functionality and will automatically stop and reverse a

closing door if a problem is detected.

Automatic Lighting System

Two bulb lighting system supplies up to 200 Watts of light for safer evening exits and entries. Turns ON when

door is activated and automatically turns OFF 4 minutes later.

Manual Emergency Release

Manually releases door from door opener. Used during a power failure or other emergency to allow manual

opening and closing of door.

Ener-Genie™ Battery Back Up

Easily adjust the programming to reduce opening speed to a desired rate, optionally adjust limits and force, and

program new remotes.

SmartSet™ Electronic Programming

Easily adjust the programming to reduce opening speed to a desired rate, vary limits and force, and program new

remotes.

Integrated Motion Detection (Not available on all models)

Select units have motion detection built into the power head. Lights automatically turn ON when motion is

detected for much safer movement through the garage. Lights will turn OFF after 4 minutes of no motion.

TABLE OF CONTENTS

Section ....................................................................................Page

Safety Information .................................................................................................... 2

Opener Features & Safety Features ................................................................... 3

Table of Contents ....................................................................................................... 4

Installation

Important Installation Instructions ........................................................5

1 Programming Limits & Force ............................................................. 6-7

2 Program IntelliCode® 2 Remote to Power Head ..........................8

Programming HomeLink®, Car2U®, IntelliCode® 1 remotes or wireless

keypads .................................................................................................................. 9

Reference

3 Typical Installed Illustrations ................................................................ 10-12

Typical Sectional Door Installation ............................................................10

Typical One Piece Door Installation ...........................................................11

Power Head & Rail Assembled View ...........................................................12

4 Overview of Power Head Controls .............................................................13

5 Overview of Remotes and Options ...................................................... 14-16

Panic Button .......................................................................................................14

IntelliCode® Features ........................................................................................ 15

Previously Installed Openers ..........................................................................1

Lost or Stolen Remote - Clearing Memory ..................................................16

6 Maintenance & Troubleshooting ......................................................... 17-25

Important Safety Instructions ........................................................................ 17

Routine Monthly Maintenance .....................................................................17

Door Balance (Spring Tension) ......................................................................17

Safe-T-Beam® System Check .......................................................................... 17

Contact Reverse Test .........................................................................................18

Motion Detector - Overview ...........................................................................18

Reset - Open/Close Travel Limit .....................................................................18

Carriage Engage/Disengage .......................................................................... 18

Wall Console - Overview .................................................................................. 19

Change Light Bulbs ........................................................................................... 19

Optional Dual Wall Console - Installation .................................................19

Chain or Belt Tension Adjustment ................................................................ 20

Remote Battery Replacement ........................................................................20

Wiring Diagram ................................................................................................21

Speed Adjustment ............................................................................................22

Force Adjustment .............................................................................................. 23

Troubleshooting Guide - Operation ..................................................... 24-25

Troubleshooting Guide - Power Head LEDs ...............................................25

Warranty ......................................................................................................................26

PATENT STATEMENT

Patents Pending

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING: To reduce the risk of severe injury or death:

1. READ AND FOLLOW ALL SAFETY, INSTALLATION

AND OPERATION INSTRUCTIONS. (If you have

questions or do not understand an instruction, call

The Genie Company.)

2. Install only on a properly balanced sectional or

one piece garage door. An improperly balanced

door could cause severe injury. Have a trained door

system technician make repairs or adjustments to

cables, spring assemblies, and other hardware before

installing the opener.

3. Remove all ropes and remove or make inoperative all

locks connected to the garage door before installing

opener.

4. Where possible, install the door opener 7 feet or

more above the floor. For products having an

emergency release, mount the emergency release 6

feet above the floor.

5. Do NOT connect the opener to source of power until

instructed to do so.

6. Locate the wall console:

• Within sight of the garage door,

• At minimum height of 5 feet so small children

are not able to reach it, and

• Away from all moving parts of the door.

7. Install the Entrapment WARNING Label next to the

wall console in a prominent location.

8. After installing the opener, the door must reverse

within 2 seconds when it contacts a 1-1/2 inch high

object (or a 2 x 4 board laid flat) on the floor.

OPENER MUST BE INSTALLED WITH THE INCLUDED

WALL CONSOLE.

Safe-T-Beam® SAFETY REVERSE SYSTEM MUST BE

INSTALLED TO CLOSE DOOR.

INFRARED PROTECTION FUNCTION

1. When garage door is opening, its movement will not be influenced if the Safe-T-Beam® is

obstructed.

2. If the Safe-T-Beam® is obstructed before the garage door fully closes, the door will not close.

3. When the garage door is closing, if Safe-T-Beam® is interrupted by person or obstacle, the garage

door will stop its downward travel and reverse automatically to its fully opened position.

4. Remove Safe-T-Beam® obstruction.

5. If the Safe-T-Beam® System fails, loses power, or is installed improperly, press and hold the wall

console "open/close" button until the door reaches its fully closed position. If you release the

"open/close" button on the wall console during the closing movement the door will reverse

automatically to its fully opened position.

A PDF VERSION INSTALLATION POSTER IS AVAILABLE AT WWW.GENIECOMPANY.COM

OR CALL 1.800.354.3643 TO OBTAIN AN EMAIL PDF FILE

The following mechanical assembly tasks must be completed before continuing.

 Power head and rail are bolted to each other (An illustration is shown on page 12)

(Example illustrations of the following items are shown on pages 10 and 11)

 Rail end is attached to the garage door header

 Power head is attached to a support frame suspended from the ceiling or ceiling joists

 Rail door arm is attached to the garage door

 Safe-T-Beam® units installed and wired

 Wall console installed and wired

 Door arm carriage is engaged to the chain or belt drive

 Power head is plugged into an approved power outlet

Begin programming by setting Limits on the next page.

PROGRAM

SET

—

5 SECS

SETTING & TESTING LIMITS AND FORCE

The OPEN (UP) and CLOSE (DOWN) Door Limit positions are controlled by making

adjustments using the panel located on the bottom of the power head. Begin with

Step 1 and continue through Step 10. Door Force is set during the final Open/Close

cycle of these steps. The power head will automatically set door speed at slow if the

distance between limits is less than 6 feet.

A) CLOSE DOOR TRAVEL LIMIT

NOTE: You can start and stop door

movement using either buttons until

door is in correct open or closed position.

Watch door move

PROGRAMMING LIMITS & FORCE (Continuing from Installation Poster

if provided)

RAM

—

PRESS and HOLD

PROGRAM

SET

—

PRESS and HOLD

SEE BOTH

Blue LEDs

come ON

SEE round

Blue LED

come ON

OGRAM

SET

—

SEE round Blue

LED flashing

RELEASE

2 3

NOTE: If one or both LEDs come ON RED at this

time; Limits programming menu was not entered

properly. You must exit programming and restart.

To exit this mode:

A. Press

PROGRAM

SET

and release

B. Pause

C. Press

PROGRAM

SET

and release

D. Pause

E. Begin with Step 1 on this page. Restarting at

Step 1 will reset RED LEDs to BLUE.

PRESS and RELEASE

WARNING

• Make sure doorway is in view and clear of obstacles

and people to avoid injury or damage to property.

• DO NOT operate this unit from wall console before

LIMITS and FORCE are set. Severe damage to the

opener can occur.

• Bullet MUST be engaged to carriage BEFORE setting

limits. See Installation Poster (if provided) or refer to

pages 12 and 18.

Please note that there is a 30 second timeout

between each programming step.

A programming timeout during these steps has

occured when two RED flashing LEDs appear.

In the event of a timeout please restart at Step 1.

NOT CE

O R C M UC D

U O N N H D

Travel door to FULL CLOSED position

RELEASE

PRESS and

RELEASE

SEE long Blue

LED come ON

If RED LED comes ON - STOP and

exit programming.

OGRAM

SET

—

PRESS

SEE long Blue LED

flashing

Watch door move

SET

—

B) OPEN DOOR TRAVEL LIMIT

NOT E

O R M O R C D

OW O A D

DOOR CLOSES

DOOR OPENS

Door Limits are set.

Both LEDs go OFF.

Continue with

FORCE setting.

SET FORCE Force is set automatically with first full

OPEN/CLOSE door operation.

Continue with programming remotes on the next

page of this manual.

PRESS and

RELEASE

PRESS and HOLD

PRESS and

RELEASE

PRESS and

RELEASE

OGRAM

SET

—

Travel door to FULL OPEN position

RELEASE

NOTE: You can start and stop door

movement using either

buttons until

door is in correct open or closed position.

PROGRAM

SET

—

5 SECS

PROGRAM

SET

—

PROGRAM INTELLICODE® 2 REMOTE TO POWER HEAD FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

PRESS and HOLD

SEE BOTH

Blue LEDs

come ON

SEE round Blue

LED come ON

SEE long Purple

LED flashing

SEE long Purple LED

come steady ON

RELEASE

2 3

6 7

The next press of the remote will operate door.

Repeat as necessary for other remotes.

Bring remote(s) to power head location.

Begin with Step 1 and continue through Step 7 for each button to be programmed.

NOTE: The following instructions are for the remote(s) provided with this opener.

Remote(s) provided with this opener use a IntelliCode® 2 electronic access code

system. Refer to page 15 for additional information on IntelliCode® 1 and 2 remotes.

See page 9 for programming instructions using IntelliCode® 1 remotes.

PRESS and

RELEASE

PRESS and

RELEASE

PRESS and

RELEASE

Basic power head programming is complete.

Your garage door opener is ready to use.

WARNING

A moving door can cause serious injury or death.

1. Keep people clear of opening while door is moving.

2. Do NOT allow children to play with opener, including

wall console, remote, or wireless keypad.

3. During programming, door opener could begin to run,

so stay away from moving door and its parts.

SEE both LEDs OFF

SEE both LEDs

flash Blue

PRESS and

RELEASE

PROGRAM

SET

—

5 SECS

PROGRAM

SET

—

PRESS and HOLD

SEE BOTH

Blue LEDs

come ON

SEE one

Blue LED

come ON

PRESS a previously programmed Genie®

IntelliCode® 2 remote button on remote. If you

are unsure which remote you have see page 15.

Remote must be IntelliCode® 2 enabled.

RELEASE

1 2 3 4

OPTIONAL PROGRAMMING POWER HEAD TO

Homelink®, Car2U®, or IntelliCode® 1 REMOTES and SERIES II WIRELESS KEYPADS

To complete any of these tasks you MUST have at least one Genie® IntelliCode® 2 remote button already

programmed to the power head.

Homelink® or Car2U®: You must also have your Homelink® or Car2U® enabled vehicle present and their

programming instructions to perform these programming steps.

Genie® remote: You must also have your Genie® IntelliCode® 1 remote present.

Genie® wireless keypad: You must also have your Genie® wireless keypad installed and a PIN already programmed into the keypad.

PRESS and

RELEASE

On the IntelliCode® 1 remote PRESS

a button and RELEASE.

SEE both LEDs flash Blue.

IntelliCode® 1 remote or wireless keypad programming

On the IntelliCode® 1 remote PRESS

the same button and RELEASE.

The next press of the remote will

operate door.

Enter your wireless keypad PIN.

Press and hold button

(3 seconds) on wireless keypad and

see on power head long LED come ON

Purple. (You may have to press

more than once.)

Test. Repeat as necessary for any

other IntelliCode® 1 remotes.

Press and hold button

(3 seconds) on wireless keypad again

and see on power head both LEDs

come ON Blue.

Wait 30 seconds and test operation.

Genie® IntelliCode® 1 remote Genie® IntelliCode® 1 wireless keypad

SEE long Purple

LED flashing

SEE both LEDs

flash Purple

All optional programming is complete. Your garage door opener is ready to use.

For Car2U® enabled vehicles follow the Car2U®

instructions.

Test. Repeat as necessary for any other Car2U®

enabled vehicle.

Homelink® or Car2U® programming

If your Homelink® has been previously programmed to an

Genie® opener begin with Step 5.

If your Homelink® has not yet been linked to a Genie®

opener then go to page 15 and change one remote button

from IntelliCode® 2 to IntelliCode® 1, then program that

button to the power head and repeat steps 1-4 then

continue with Homelink® steps 5-6.

PRESS the Homelink® button twice.

Test. Repeat as necessary for any other pre-

programmed Homelink® enabled vehicle.

NOTICE

O R B C MS O S R C ED

UL OW ON A DE

TYPICAL SECTIONAL DOOR INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

INSTALLATION TYPIQUE SUR UNE PORTE SECTIONELLE ..................................POUR OBTENIR DE L’AIDE-1.800.354.3643

INSTALACIÓN HABITUAL DE UNA PUERTA SECCIONAL ...................................PARA OBTENER AYUDA, LLAME AL 1.800.354.3643

SAFE-T-BEAM® SENSORS

PALPEURS de SAFE-T-BEAM®

SENSORES SAFE-T-BEAM®

OPTIONAL - HEADER BRACKET MOUNTING

BOARD

PLANCHE DE MONTAGE FACULTATIVE POUR SUP-

PORT D’EMBASE

TABLERO DE MONTAJE OPCIONAL DE SOPORTE DEL

TRAVESAÑO

BRACING

ATTACHE

ARRIOSTRAMIENTO

POWER CORD* (APPROX. 45 IN.)

TO 120V GROUNDED OUTLET

CÂBLE D’ALIMENTATION* (ENVI-

RON 45 PO.) À PRISE DE CONTACT

DE 120V À CONTACT DE MISE À

LA TERRE

CABLE DE ALIMENTACIÓN* (45

PULG. APROX.) A UN TOMACOR-

RIENTE DE 120 V CONECTADO A

TIERRA

EXTENSION SPRING

RESSORT DE TRACTION

RESORTE DE EXTENSIÓN

TORSION SPRING

RESSORT DE TORSION

RESORTE DE TORSIÓN

OR / OU / O

TYPICAL SUPPORT BRACKET (NOT PROVIDED)

SUPPORT TYPIQUE (NON FOURNI)

ESCUADRA DE SOPORTE TÍPICA (NO SE INCLUYE)

*Direct wiring of power supply to opener must be installed by a licensed electrician.

*Le câblage direct de l'alimentation électrique à l’ouvre-porte doit être installé par un électricien agréé.

*Un electricista autorizado debe instalar el cableado directo del suministro de energía hacia el abridor.

FIG. 3-1

DOOR ARM

BRAS DE LA PORTE

BRAZO DE LA PUERTA

NOTE: For Low Headroom

installations do NOT reduce door

arm lengths by cutting door arms.

To clear door, reposition door

arms with greater angle.

REMARQUE: Pour les installations

à basse hauteur, ne PAS réduire la

longueur du bras de la porte en

coupant les bras de la porte. Pour

dégager la porte, repositionnez les

bras de la porte à un plus grand

angle.

NOTA: Para instalaciones a alturas

bajas, NO reduzca las longitudes de

los brazos de la puerta cortándolos.

Para despejar la puerta, vuelva a

colocar los brazos de la puerta en otra

posición con un ángulo mayor.

MAX. 6" - MIN. 5"

6 po (15 cm) MAX. -

5 po (12,7 cm) MIN.

MAX. 6" - MIN. 5"

SECTIONAL DOOR

PORTE SECTIONELLE

PUERTA SECCIONAL

ONE PIECE DOOR

PORTE D’UNE PIÈCE

PUERTA DE UNA SOLA PIEZA

O R E OM S BSTU TED

U DO N O H N LE

LIFT SPRING

RESSORT DE LEVAGE

RESORTE DE ELEVACIÓN

*Direct wiring of power supply to opener must be installed by a licensed electrician.

*Le câblage direct de l'alimentation électrique à l’ouvre-porte doit être installé par un électricien agréé.

*Un electricista autorizado debe instalar el cableado directo del suministro de energía hacia el abridor.

TYPICAL ONE PIECE DOOR INSTALLATION ............ FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

INSTALLATION TYPIQUE D’UNE PORTE DE GARAGE D’UNE PIÈCE ..............POUR OBTENIR DE L’AIDE-1.800.354.3643

INSTALACIÓN HABITUAL DE PUERTA DE UNA SOLA PIEZA .....................................PARA OBTENER AYUDA, LLAME AL 1.800.354.3643

FIG. 3-2

WARNING

To reduce the risk of injury to persons or damage to property -

Use this opener only with a one piece or sectional door.

AVERTISSEMENT

Pour diminuer le risque de blessures corporelles ou

d’endommagement matériel - Utiliser cet l’ouvreur uniquement

avec les portes à section.

ADVERTENCIA

Para reducir el riesgo de lesión a las personas o daños a la propiedad -

Use este abridor solamente con puertas en secciones.

SAFE-T-BEAM® SENSORS

PALPEURS de SAFE-T-BEAM®

SENSORES SAFE-T-BEAM®

POWER CORD* (APPROX.

45 IN.) TO 120V

GROUNDED OUTLET

CÂBLE D’ALIMENTATION*

(ENVIRON 45 PO.) À PRISE

DE CONTACT DE 120V À

CONTACT DE MISE À LA

TERRE

CABLE DE ALIMENTACIÓN*

(45 PULG. APROX.) A UN

TOMACORRIENTE DE 120 V

CONECTADO A TIERRA

HEADER BRACKET MOUNTING BOARD

PLANCHE DE MONTAGE FACULTATIVE POUR

SUPPORT D’EMBASE

TABLERO DE MONTAJE DE SOPORTE DEL TRAVESAÑO

TYPICAL SUPPORT BRACKET (NOT PROVIDED)

SUPPORT TYPIQUE (NON FOURNI)

ESCUADRA DE SOPORTE TÍPICA (NO SE INCLUYE)

REFERENCE - POWER HEAD & RAIL ASSEMBLED VIEW

RÉFÉRENCE – VUE DE LA TÊTE D’ALIMENTATION & DU RAIL ASSEMBLÉ

REFERENCIA - VISTA DEL CABEZAL ELÉCTRICO Y RIEL ENSAMBLADOS

NOTE: Use wall console and safety sensors provided with this unit. Do NOT substitute wall console or safety sensors.

REMARQUE: Utilisez la console sur le mur et les capteurs de sécurité fournis avec cet appareil. NE PAS substituer la console du mur ou les capteurs de sécurité.

NOTA: Use la consola de pared y los sensores de seguridad proporcionados con esta unidad. NO sustituya la consola de pared ni los sensores de seguridad.

FIG. 3-3

Tensioner (located inside rail)

Tendeur (situé à l'intérieur du rail)

Tensor (ubicado dentro del riel)

Release Handle

Poignée de déverrouillage

Palanca de liberación

POWER HEAD

TÊTE DE PUISSANCE

CABEZA DE LA ENERGÍA

Power Cord

Cordon de secteur

Cable eléctrico

Door Arm

Bras de la porte

Brazo de la puerta

One Piece Door, Door Arm Assembly

Porte d’une pièce, Montage du bras de la porte

Puerta de una sola pieza, Conjunto del brazo de la puerta

Sectional Door, Door Arm Assembly

Porte en section, Montage du bras de la porte

Puerta seccional, Conjunto del brazo de la puerta

Support Bracket (for extended PRO rails only)

Support (seulement pour les rails PRO étendus)

Escuadra de soporte (sólo para rieles PROFESIONALES extendidos)

Header Bracket

Embase support

Soporte del travesaño

Clevis Pin, Long

Axe de chape, longue

Pasador de grillete, largo

Clip

Étrier

Abrazadera

Engage chain or belt bullet to Carriage Slide

Embrayez la chaîne ou la courroie balle

à la coulisse du chariot

Enganche la cadena o correa bala al deslizamiento del carro

Door Arm

Bras de la porte

Brazo de la puerta

See BLUE bag for screws

Voir le sac BLEU pour des vis

Vea el bolso AZUL para los tornillos

See GREEN bag for parts

Voir le sac VERT pour des pièces

Vea el bolso VERDE para las piezas

OT CE

DOOR OM O R C

W A

Chain or belt (located inside rail)

Chaîne ou courroie

(qui se trouve à l'intérieur du rail)

Cadena o correa (ubicada dentro del riel)

Carriage Slide (located inside rail)

Coulisse du chariot (situé à l'intérieur du rail)

Deslizamiento del carro (ubicado dentro del riel)

Bullet

Balle

Bala

RETAIL RAIL

RAIL DE DETAIL

RIEL DE VENTA AL MENUDEO

Rail Connector

Maillon de junction du rail

Conector del riel

PROFESSIONAL INSTALLER RAIL

RAIL PROFESSIONNEL D'INSTALLATEUR

CARRIL PROFESIONAL DEL INSTALADOR

Rail Connector

Maillon de junction du rail

Conector del riel

SET

PROGRAM

Open

Travel

Button

ROUND

LED Indicator

(Light)

Facing

Garage Door

LONG

LED Indicator

(Light)

Travel

Button

OVERVIEW OF POWER HEAD CONTROLS

This section describes the simple programming

functions. Use this page to familiarize yourself with the

buttons and LED indicators used to program the opener.

PROGRAM

SET

—

To garage door

FIG. 4-1 Locate programming buttons

Controls location

on power head.

FIG. 4-2 Programming buttons

There are three programming buttons and two lights

(LEDs) on the power head.

Each of the buttons are used to enter and complete

the setup programming. The LEDs indicate status or a

function change by illuminating ON, OFF, or ON flashing

in one of three different colors; BLUE, RED, or PURPLE.

Throughout the instructions in this manual the buttons

and LEDs are also displayed as icons.

Buttons

Name Shape Use

Program button

PROGRAM

SET

Enters into and selects

programming menus

Close Travel button

multi-function;

moves door, advances

through menus

Open Travel button

multi-function;

moves door, advances

through menus

LED Colors

Round Red and Long Red

Round Purple

and Long Purple

Round Blue

and Long Blue

Programming Overview

There are four Power Head program menus:

Remote Program (Default menu)

Limits Program

Speed Program*

Force Program*

Programming steps for Limits and remotes found on

pages 6 through 9.

*Force and Speed settings are set at the factory and do

not normally require adjustment programming. Custom

programming instructions for Speed and Force are

located in the Troubleshooting Section of this manual.

These are the basic steps to enter into the four

programming menus:

1. Press

PROGRAM

SET

and hold till both BLUE lights come ON then

release.

2. Both LEDs go out and Round BLUE light comes

ON. You are in the Program Menus at the Remote

Programming.

By using the

or the button you can advance to

the Limits, Speed, or Force program menus and the

LED display will change accordingly.

Each program menu has a specific LED display.

Press Program LED Display

Default Remote Round Blue

Limits Long Blue

X2 Speed Round Blue & Long Blue

X3 Force Round Red

3. Press

PROGRAM

SET

button to enter into the program menu

functions.

If you have entered into an unwanted program

menu, press

PROGRAM

SET

button again to exit the programming

functions.

Programming function will time out after 30 seconds

if there is no key stroke activity.

OVERVIEW - REMOTES AND OPTIONS

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS

210 of Industry Canada. This equipment has been

tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide

reasonable protection against harmful interference

in a residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not

occur in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which may be determined

by turning the equipment OFF and ON, the user is

encouraged to try to correct the interference by

one or more of the following measures:

• Re-orient or relocate the receiver antenna.

• Increase the separation between the opener and

receiver.

• Connect the opener into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult your local dealer.

FIG. 5-1 Remote (vary by model)

WARNING

A moving door can cause serious injury or death.

1. Keep people clear of opening while door is

moving.

2. Do NOT allow children to play with opener,

including wall console, remote, or wireless

keypad.

3. During programming, the door opener could

begin to run, so keep people and objects away

from the moving door and its parts. To keep the

door from moving, close the door and disconnect

it from the rail carriage by pulling the Emergency

Release Handle. See page 18 for Release Handle

operation.

Three Button

Remote

Three button Remote

with Panic Button

feature

Panic Button OPERATION

1. Press Panic Button. Alarm will

sound from power head.

2. Press Panic Button again. Alarm

will stop.

Panic Button

PANIC BUTTON

(Not available on all models)

Openers and remotes equipped with this feature provide

additional security when exiting/entering the garage

area. The Panic Button is located on the remote as shown

below. Alarm will sound from power head.

3. Press the same button

twice to toggle IntelliCode®

selection from IntelliCode® 2

to IntelliCode® 1.

INTELLICODE® FEATURES

Earlier models of Genie® garage door openers,

remotes, and wireless keypads use IntelliCode®

1 signals to communicate. Remote(s) provided

with this unit will transmit either IntelliCode® 1 or

IntelliCode® 2 signals.

Remote(s) contained in this package are preset

to IntelliCode® 2 and can be configured to

communicate with previously installed IntelliCode®

1 openers. This dual IntelliCode® option allows one

IntelliCode® 2 remote to operate BOTH new and

current models of The Genie Company garage door

openers.

This new Genie® garage door opener will ONLY

accept signals from a remote sending IntelliCode® 2

signals or a Genie® brand IntelliCode® 1 remote that

has been programmed to the opener using a new

IntelliCode® 2 remote.

NOTE: Other remotes not enabled with Genie®

IntelliCode® 2 will not operate this opener.

If you have garage door

openers*

Best choice of

IntelliCode®

programming

One or more IntelliCode® 2

openers.

Maximum 3 different openers

Use IntelliCode® 2

Mixture of openers

manufactured between 1997

and 2010 (IntelliCode® 1) and

new IntelliCode® 2 openers

Use IntelliCode® 2

and/or 1

One or more openers

manufactured between 1997

and 2010 (IntelliCode® 1)

Use IntelliCode® 1

* Maximum 3 different openers per each 3 button

remote.

Programming to previously installed Series II

(IntelliCode® 1) Genie® garage door openers

Remote(s) provided with this unit can operate

earlier (Series II) models of Genie® garage door

openers. The default Series III (IntelliCode® 2)

frequency must be changed to IntelliCode® 1.

(Follow these same steps to change IntelliCode® 1

back to IntelliCode® 2 frequency.)

The LED color displayed on the remote indicates

the IntelliCode® transmitting mode.

Red = IntelliCode® 1 / Green = IntelliCode® 2

1. Select a button on the remote that has NOT been

programmed to the new power head.

2. Press and hold that button for 10 seconds.

Both Red and Green

LEDs come ON and stay

ON.

10 SECS

4. Press the same button again

to confirm toggle. The

IntelliCode® selection for this

button is set to IntelliCode® 1.

5. Take the remote to the earlier Genie® garage

door opener and follow that opener's instructions

to program a new remote.

Repeat for other Genie® garage remote(s) as

necessary.

Red LED Green LED

Three button

remote

TRANSMITTER COMPLIANCE STATEMENT

Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture.

No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters

are to be used in another country, the importer must determine compliance with any local laws and

regulations which may differ from United States and Canadian requirements prior to use.

Los transmisores cumplen con todas las reglamentaciones legales de los Estados Unidos y del Canadá, en

la fecha de fabricación. Ninguna garantía se da que cumplan con todas las reglamentaciones legales de

ninguna otra jurisdicción. Si los transmisores se van a utilizar en otro país, el importador debe determinar

si cumplen con las reglamentaciones y leyes locales que puedan ser diferentes a las reglamentaciones de

los Estados Unidos y del Canadá, antes de usar los mismos.

Les émetteurs sont conformes à la réglementation américaine et canadienne à compter de leur date de

fabrication. Aucune garantie n’est stipulée indiquant qu’ils sont conformes à toutes les prescriptions

juridiques d’autres autorités. Si les émetteurs sont utilisés dans d’autres pays, il incombe à l’importateur

d’en déterminer leur conformité aux lois et règles locales pouvant différer de celles des États-Unis et du

Canada avant toute utilisation desdits émetteurs.

Sendegeräte entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der

Herstellung. Wir übernehmen keine Gewährleistung für die Einhaltung aller gesetzlichen Bestimmungen

in anderen Ländern. Sollen Sendegeräte in anderen Ländern eingesetzt werden, so muss der Importeur

vor dem Gebrauch sicherstellen, dass die Sendegeräte auch solchen lokalen Bestimmungen entsprechen,

welche von den Bestimmungen der USA und Kanadas abweichen.

LOST OR STOLEN REMOTE - CLEARING MEMORY

Clearing remotes from power head memory will

clear ALL programmed remotes and wireless

keypad.

NOTE: Follow the PROGRAM REMOTE TO POWER

HEAD steps to reenter remaining or new remotes.

1. Press

PROGRAM

SET

and hold

until both lights

come ON blue.

Release button.

2. Lights go out and

Round BLUE light comes ON.

3. Press

PROGRAM

SET

again and

both lights flash

purple.

PROGR AM

SET

—

4. Press both and

simultaneously on the

power head and hold for

5 seconds.

• Test a remote operation. Remote will not

activate door opener.

• Garage door opener will operate normally using

wall console.

• Program remaining or new remotes as shown

on page 8. Your door opener will no longer

recognize any signal received from the missing

remote, or any other which has not been

reprogrammed to the power head.

OGRAM

SET

—

5 SECS

PROGR AM

SET

—

5 SECS

MAINTENANCE & TROUBLESHOOTING FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

WARNING

• Garage door hardware (springs, cables, brackets,

pulleys, etc.) are under extreme pressure and

tension.

• DO NOT attempt to repair or adjust door

springs or any hardware, and DO NOT OPERATE

garage door automatically or manually if door

is improperly balanced or springs are broken.

– CONTACT A TRAINED DOOR SYSTEM

TECHNICIAN.

ROUTINE MONTHLY MAINTENANCE

Basic monthly maintenance tasks.

• Door balance

• Safe-T-Beam® System Check

• Contact reverse

Instructions for these tasks and others are found on

the following pages.

DOOR BALANCE (SPRING TENSION)

• With the door closed, pull

release handle

DOWN and let go to release door carriage

assembly from drive system.

• Raise door manually approximately 3’- 4’ and

release.

– Door should remain stationary or move very

slightly.

– If door moves quickly, CONTACT A TRAINED

DOOR SYSTEM TECHNICIAN.

• Close the door.

• Pull emergency release handle DOWN and let go

to engage carriage assembly to drive system.

– Operate door using remote or wall console.

– Door will re-attach itself to carriage assembly.

If you have any questions, please do not hesitate to contact customer service at: 1.800.354.3643

3’ - 4’

Sectional Door

3’ - 4’

One-Piece Door

FIG. 6-1 Door balance

WARNING

Use wall console supplied with opener. Any

other wall console can cause the opener to

operate unexpectedly.

Safe-T-Beam® (STB) SYSTEM CHECK

• STB Red and Green LEDs ON steady, system OK

• STB Red LED flashes

– Check for obstruction

– Check alignment

– Verify wire routing from STBs

to STB connection in power

head

– Check for signal interference

from another Safe-T-Beam®

unit

• No STB Red or Green LED displayed

– Check wiring and wire connections

STB BWC IWC

NOT

USED

NOT

USED

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of severe injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with the door controls. Keep the remote away from children.

3. Always keep the moving door in sight and away from people and objects until the door is completely closed. NO

ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

4. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.

5. Test opener monthly. The door MUST reverse on contact with a 1-1/2" high object (or a 2" x 4" board laid flat)

at the center of the doorway on the floor. After adjusting either the force or the limit of travel, retest the door

opener. Failure to adjust the opener properly may cause severe injury or death.

6. When possible, use the emergency release only when the door is closed. Use caution when using this release

with the door open. Weak or broken springs are capable of increasing the rate of door closure and increasing the

risk of severe injury or death.

7. KEEP DOORS PROPERLY BALANCED. See your garage door Owner’s Manual. An improperly balanced door

increases the risk of severe injury or death. Have a trained door system technician make repairs to cables, spring

assemblies, and other hardware.

SAVE THESE INSTRUCTIONS.

CARRIAGE ENGAGE/DISENGAGE

Use Release Handle to manually engage or

disengage Carriage.

RESET - OPEN/CLOSE TRAVEL LIMIT

Performing all ten (10) Limits/Force setting steps

(pages 6-7) erases previous Limits/Force settings.

NOTE: The opener will not close the door

automatically unless the Safe-T-Beam® System is

installed and Limits are programmed.

MOTION DETECTOR - OVERVIEW

(Not available on all models)

Power heads equipped with a motion detector

sensor provide additional security when

exiting or entering the garage area.

NOTE: Sensor positioning on the power head does not

provide motion monitoring above the power head.

OPERATION

• Motion detector sensor is always ON. There are NO

user controls or adjustments.

• Lights automatically turn ON when motion is

detected and will turn OFF after 4 minutes of no

motion.

• Motion detector sensor will not turn OFF lighting

turned ON at the wall

console.

• Lighting turned ON at the wall console will remain

ON until wall

console turns lighting OFF or opener

is used.

PROGRAM

—

Motion Detector Sensor

CONTACT REVERSE TEST

The Force and Limit settings MUST be

COMPLETED before testing.

1. Testing.

• Open garage door using wall console.

– Place a 2" x 4" board (laid flat) under center of

garage door opening (Fig. 6-2).

• Close garage door using wall console.

• When door contacts board, the door must

stop (within 2 seconds) and reverse direction

returning to open position.

2. Adjustment.

• If the door does not reverse.

– Check to see if door has "down" limit properly

set in the fully closed position. It should not

have reached its "close" limit before hitting

board. Reprogram close limit with door

completely closed.

– If the door STOPS but does not reverse, reset

your limits. Remove board. Return to pages

6-7 and repeat Limits settings to correct down

limit.

• Test again. Repeat as necessary until door

reverses upon contacting board.

FIG. 6-2 2 x 4 under center of door opening

NOTICE

F DOOR B COMES OBSTRUCTED

PULL DOWN ON HANDLE

TO RELEASE CARRIAGE:

1. Pull DOWN on handle and let go.

2. Verify RED block is showing.

3. Raise or lower door manually.

DOOR

PULL

TO ENGAGE CARRIAGE:

1. Pull DOWN on handle and let go.

2. Verify RED block is NO LONGER showing.

3. Raise or lower door using remote or wall console.

Release Handle

FIG. 6-3 Disengage Carriage

LOCKED

UNLOCKED

WHEN RED BLOCK IS SHOWING

CARRIAGE IS UNLOCKED

FIG. 6-4 Carriage

(Standing below rail looking up at

carriage)

Independent Light Control Button

– Controls door opener lights from inside garage

– Shuts OFF lights 4 minutes after door action

Vacation Lock Button

– LOCK disables controls

after door is completely

closed

– UNLOCK allows controls to

work normally

Indicator Light

Red indicator light is always ON

When Vacation Lock is ON the

indicator light flashes

Open/Close Button

Open and closes door from inside garage

WALL CONSOLE - OVERVIEW

Use only the Series III wall console provided with this

unit. Wall consoles from other manufacturers will not

work with this power head.

Earlier Genie® Series II

wall consoles will not work with this power head

Wall console has three buttons and one indicator light.

Indicator Light

Indicator light will display red when wall console

is properly wired and Vacation Lock is OFF. When

Vacation Lock is ON indicator light flashes.

Open/Close Button

Use this button to open or close garage door. When

Vacation Lock is ON the Open/Close button will

CLOSE door only. Note: Constant button pressure in

the CLOSE mode will override error responses in the

power head and close door.

Independent Light Control Button

Use this button to turn power head lights ON. Power

head lighting will remain ON until this button is

pressed again or a door action has been completed.

Note: If opener has a Motion Detector sensor the

sensor will keep power head lights ON as long as

motion is detected.

Vacation Lock Button

When Vacation Lock is ON the power head cannot be

activated by the wall console or a remote.

• Press and hold for 5 seconds (or till Indicator Light

flashes) to activate Vacation Lock.

• Press and release to turn Vacation Lock OFF.

OPTIONAL DUAL WALL CONSOLE - INSTALLATION

Use only the Series III wall console provided with this

unit. An optional second

Genie® Series III wall console

(not provided) can be added.

STB BWC IWC

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE #1

FROM WALL

CONSOLE #2

POWER HEAD

WALL

CONSOLE #1

WALL

CONSOLE #2

TO WALL CONSOLE #1

B/W

BOTH TO POWER HEAD

WALL

CONSOLE #1

WALL

CONSOLE #2

STB BWC IWC

NOT

USED

NOT

USED

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE

Tip: If indicator light on wall console comes ON, but

there is NO

operation from

buttons -

verify

wall console

wire

routing

at power head

connector.

STB BWC IWC

NOT

USED

NOT

USED

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE

STB BWC IWC

FRO STBs

FROM WALL

CONSOLE

STB

BWC

IWC

OM STBs

ROM WA

OM W

OLE

ONSO

CHANGE LIGHT BULBS

WARNING

• Observe all safety warning and precautions!

Improper light bulb removal or replacement

could result in Death or Serious Injury.

• Disconnect power from opener before

beginning this task.

• When replacing light cover, make sure wires are

not pinched or near moving parts.

1. Disconnect power to door opener.

• Open power head light cover.

• Remove light bulb(s).

• Replace with maximum 100 Watt light bulbs.

– Do NOT use light bulbs with greater than 100

Watt rating.

• Close power head light cover.

2. Reconnect power to door opener.

• Test light operation.

CHAIN OR BELT - TENSION ADJUSTMENT

WARNING

• Observe all safety warning and precautions!

• Disconnect power from opener before

beginning this task.

Visually inspect the chain or belt once per year.

• At the center of the rail, is chain or belt resting on

rail? The chain or belt should not be resting on

the rail. Tighten adjustment nut until chain/belt

does not, at the center of the rail, rest on rail.

• Is there rust on chain or frayed edges on belt?

Contact a trained door system technician for

chain/belt replacement.

• Are there kinks or twists in the chain or belt?

Contact a trained door system technician for

chain/belt replacement.

Tighten nut to increase

tension on chain or belt

Chain

Chain at center of rail

Adjustment required

Correctly adjusted

Belt

Belt at center of rail

Adjustment required

Correctly adjusted

BELT

CHAIN

REMOTE BATTERY REPLACEMENT

Replace remote battery with a CR 2032 coin cell battery.

1. Open the remote case using a washer or coin that fits

into the slot at the top of the remote.

2. Replace battery.

3. Align components and snap case closed.

La page charge ...

Genie 3024 Manuel utilisateur

Marque: Genie

Modèle: 3024

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Genie 3024 User manual

Genie 3024 Manuel utilisateur

Ce manuel convient également à

Genie 3024 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents